Transcript
PA-85 Portable Sound System with Bluetooth®
USER’S MANUAL www.lenco.com
Warning 1. 1.WARNING: The batteries (battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. 2.
This equipment is a Class II or double insulated electrical appliance. It has been designed in such a way that it does not require a safety connection to electrical earth. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION: RISQUE DE CHOC ELECTRIQUE-NE PAS OUVRIR
3. -
This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of non-insulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock.
-
Warning: To reduce the risk of electric shock, do not remove cover (or back) as there are no user-serviceable parts inside. Refer servicing to qualified personnel.
-
The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance instructions in the literature accompanying the appliance.
4.
Caution- To prevent electric shock hazard, do not connect to mains power supply while grille is removed.
5.
Correct Disposal of this product. This marking indicates that this product should not be disposed with other household wastes throughout the EU. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources. To return your used device, please use the return and collection systems or contact the retailer where the product was purchased. They can take this product for environmental safe recycling.
2
Thank you very much for buying this Mobile Battery Bluetooth Speaker! In order to make the speaker function best, please take time to read this instruction manual carefully before use. It will help you to know every function better. Please keep well this user’s manual for longtime reference. CAUTION To avoid failure and damage when using this device, please read this user’s manual and make sure that you fully understand the safety and operation instruction. These instructions should be kept for your longtime reference. 1. This speaker offers you 3 different power supplies: AC 230V 50-60Hz; external DC 12-15V (Min. 50W), and rechargeable lead-acid battery DC 12V 4.5AH. 2. DO NOT attempt to touch any inside parts of the speaker system to avoid any possible risk of electronic shock. 3. DO NOT attempt to service the system beyond that specified in this operation instructions. All servicing should be referred to qualified service centers. 4. The power cord of the speaker should be un-plugged from the outlet when left unused for a long time. 5. The speaker should be situated at least 20cm from other appliances so that its location is not interfered with proper ventilation. 6. The speaker should be kept away from heat sources such as radiators, heat register, stoves, or other appliance that produce heat. 7. Never place the speaker in the locations liable to be splash nor put any water containers on the subwoofer, like glass, cup, vase and etc. If any liquid or metal parts enter into the speaker, please power OFF the power and contact qualified service centers to check the speaker before continuing usage. 8. When you are not using the speaker, please power off the speaker and unplug the power cord from the power supply. 9. When using a power socket or coupler as a power ON/OFF device, please ensure that this device can be easily accessed and operated. BATTERY CAUTION 1. Make sure to charge the lead-acid battery for a minimum of 12 hours for the first 3 times of using a brand new speaker. 2. Recharge the battery within 24 hours when the speaker shows in low-power or has run out of power. If you fail to charge the battery within 24 hours, it will reduce the life of the battery, causes the incapability of fully-power-charged and shortens its working time. 3. Non-professional technicians should not open the speaker or this lead-acid battery. 4. DO NOT use this lead-acid battery with other device. 5. If you want to use a new battery for this speaker, you must use one of the same specifications. Otherwise, it will cause damage or work failure to the speaker. 6. Improper battery installation will cause explosion, please ask a qualified service center to replace it. 7. After replacing with a new battery, please put the disused battery into a specified Recycle Bin or delivery it to a Recycle Institution. 8. If you do not use the speaker for a long time, please FULLY CHARGE THE BATTERY ONE TIME PER MONTH to avoid failure of battery. 3
FEATURES 1. Portable Sound System with Bluetooth 2. Support different Power Supply modes: AC 230V/ External DC 12-15V/ DC 12V(battery) 3. Built-in rechargeable lead-acid battery for outdoor usage 4. With Equalizer for professional sound adjustment 5. With Wired MIC Input with Vol. and Echo controls 6. With Guitar Input and Guitar volume control 7. With auto detect USB & SD card reader function 8. With 3.5mm and AUX input 9. With line out for external stereo equipment SPECIFICATIONS Power consumption: 40W Driver Unit: 8〞4Ω *1+ 2〞*1 Frequency Response: 60Hz-22KHz S/N Ratio: ≥85dB Power supply: Rechargeable Lead-acid Battery DC: 12V 4.5AH, External DC power supply: DC: 12-15V, AC Power supply: AC230V 50-60Hz SPEAKER CONNECTIONS 1. Insert your USB disk or SD card to the corresponding ports in the control panel referring to Diagram 1. 2. Connect your audio equipment (TV/DVD/MP3/iPhone/iPad and etc.) to the signal AUDIO INPUT ports (1 for RCA and 1 for 3.5mm) on back panel referring to Diagram 2. Remark: When both input are connected to external device, both sound will be out. In this case, press pause from one external device to play the desired device. 3. Connect the wired microphone to the corresponding MIC. IN port in the speaker control panel, and connect your electrical guitar to the GUITAR INPUT referring to Diagram 1. 4. Power Source Switch: AC INPUT, F.CHARGE/OFF, DC INPUT 5. AC Power Switch: AC ON, OFF, CHG ON Note: Please change to AUX IN or USB/SD mode first to make the microphone and electrical guitar works properly.
4
Diagram 1:
Diagram 2:
COMPUTER
Flat panel TV
DVD/CD
5
BLUETOOTH Press the INPUT SWITCHING Button until the BLUETOOTH Indicator blinks. The BLUETOOTH function is ON. Turn on the BLUETOOTH in device and start searching for this BLUETOOTH speaker. You will find device name of LENCO PA-85. Select this to link to the speaker. The Indicator will stop blinking and light up in BLUE color when you are successfully linked. After the linking, you can start to play music from your device. When Bluetooth is paired and connected, you can press and hold the play/pause button to disconnect the current connection and re-pairing once. POWER SUPPLY SELECTION Back Panel: 1. Power Jack: Insert the power cord to this jack and connect to AC 230V 50-60Hz. 2. Power Source Switch: AC INPUT, F.CHARGE/OFF, DC INPUT 3. AC Power Switch: AC ON, OFF, CHG ON How to Use the Switch: AC Power Supply, connect the power cord to AC230V 50-60Hz, switch the Power Source Switch to AC INPUT, and switch the AC power switch to AC ON. To turn the system off, switch both to OFF. Internal DC Power Supply, now the system is powered by built-in battery (12V, 4.5Ah). Switch the Power Source Switch to DC INPUT, and switch the AC power switch to AC OFF. To turn the system off, switch both to OFF. To charge the system, connect the power cord, switch the Power Source Switch to F. Charge and switch the AC power switch to CHG ON. To use and charge the system in the same time, switch the Power Source Switch to AC INPUT, and switch the AC Power Switch to CHG ON. External DC power supply: DC12-15V (Min. 50W). Turn OFF the AC POWER Button and unplug the power cord from the AC outlet. Then turn the POWER SOURCE button to DC INPUT. Then, connect the positive pole of your external power supply to the RED terminal and connect the negative pole to the BLACK terminal in speaker back panel as the below picture. The speaker here is powered by external DC power supply. This operation is for reserve usage when battery runs out of power. BATTERY PANEL This panel is to be opened ONLY when replacing a new battery by qualified service centers. To avoid any potential dangers and damages to the battery, please make sure that the new battery are of the same specification with the original battery. Please follow the below steps properly: 1. Remove the 6 outlying screws and take out the panel. 2. Take out the battery and press the clinching fasteners to unplug the lead wires. Please work carefully to avoid damages. 3. Remove the 2 screws on the metal-battery-fame. 4. Replace with the new battery. Be sure that the new battery is of the same specification with the original battery. Connect the Red cable to the Red Terminal and Black cable to Black Terminal. After inserting and plugging the terminals, please make sure that the connections are fixed tightly without any loose. 5. Screw back both metal-battery-frame and battery panel. 6
SPEAKER OPERATION INSTRUCTIONS Control Panel (Diagram 3)
1. Equalizers 2. USB/SD Indicator: When both USB and SD card are inserted, USB play first.. 3. AUX/Bluetooth indicator: blinks when searching external Bluetooth Device and keeps on when connected; Keeps on when playing by AUX. 7
4. SD card input: Insert SD card to play music. 5. USB input: Insert USB card to play music. 6. Repeat key, press this key to switch repeat one/repeat all/random: Repeat One: USB/SD indicator blinks about 2 times per second; Repeat All: USB/SD indicator blinks about 3 times per second; Random: USB/SD indicator blinks about 1 time per second. 7. Previous track/Long-press for fast backward 8. Pause and play 9. Next track/Long-press for fast forward 10. Input mode switching key: select mode from AUX to USB/SD to Bluetooth 11. Electric Guitar input port 12. Electric Guitar volume control 13. Microphone echo control 14. Microphone volume control 15. Wired microphone input port 16. Power/Low voltage Indicator: It keeps on when the unit is powered on. When the unit is in low voltage, it begins to blink. 17. Master volume control 18. Charging indicator: When charging, the CHG indicator blinks in RED. When charging is almost completed, it blinks in GREEN. When completing charging, the indicator keeps on in GREEN. Operation Reference Power
AC
Power
Source
Power
Indicator
CHG Indicator
Power Management
Unit Operation Powered by AC and Battery Charged Will
AC INPUT
AC ON
ON
Refer REMARK
YES
go into standby and charging cease after no signal input for 15 minutes
AC INPUT
OFF
OFF
*OFF
Not applicable
Switch AC Power switch to OFF, and then AC ON to power on the system again.
OFF Powered by AC and
AC INPUT
CHG ON
ON
Refer REMARK
NO
Battery Charged Won't stop charging
Not Recommended
till complete Refer REMARK (if power cord DC INPUT
AC ON
ON
NO
Powered by battery
NO
Powered by battery
Not applicable
Powered by battery
connected) *OFF(if power cord is not connected)
DC INPUT
DC INPUT
OFF CHG ON
ON
*OFF
Recommended Not Recommended
Powered by battery
Refer REMARK ON
Not
(if power cord
NO
connected)
and battery charged
Not
Won't stop charging
Recommended
till complete 8
Operation Reference Power
AC
Power
Source
Power
Indicator
CHG Indicator
Power Management
Unit Operation
*OFF (if power cord is not
NO
Powered by battery
connected) Powered by AC and CHARGING ONLY, F. Charge/OFF
AC ON
OFF
Refer REMARK
YES
Will go into standby
Not
and charging cease
Recommended
after 15minutes no signal input Powered by AC and F.
CHG
Charge/OFF
ON
OFF
Refer REMARK
CHARGING ONLY
NO
Won't stop charging till complete
F. Charge/OFF
OFF
OFF
*OFF
Not applicable
OFF
REMARK: * Blink for around 2 to 5 seconds before indication is OFF. Blink RED (Charging); Blink GREEN (Near end of charging); Green ON (Complete charging) -
The off-mode power consumption is Max. 0.23 W
-
Period of time: 15minutes
-
The power consumption in networked standby is 40 W
Mode
USB/SD Indicator At Pause, it is ON; At Play, it is Blink At Pause, it is ON; At Play, it is Blink ON OFF
USB SD AUX IN Bluetooth
AUX IN/BT Indicator OFF OFF ON Blink
TROUBLESHOOTING Troubles
Possible Reasons
Trouble Shootings
Power Indicator OFF and NO sound coming out
1. AC Power Button is still OFF 2. Battery run out of power
1. Turn the AC Power Button to ON. 2. Connect the power cord to AC 220V/50Hz outlet to test if speaker still working and to re-charge the battery.
Power Indicator ON But NO sound coming out
1. Wrongly connect the RCA or 3.5mm Audio input. 2. Master Volume is in minimum.
1. Turn OFF the speaker and check all audio cable connections. 2. Turn on the master volume to your wanted level.
Sound coming out with NOISES
Improper audio-cable connections or cross talk
1. Turn OFF the speaker and check all audio cable connections to see if they are correctly connected. 2. If all cables are well connected, that might
9
be caused by some external cross talks from your audio equipment, you can turn down the volume to solve it. Gear whines when using the microphones
1. The MIC Volume is too loud. 2. The microphones are close to the speaker
1. Turn down the MIC Volume 2. Keep the microphones at least 2 meters away from the speaker
If the speaker still out of work after checking with the above troubleshooting, please ask qualified service centers to check and repair it. DO NOT attempt to service the system beyond that specified in this operation instructions. All servicing should be referred to qualified service centers.
ACCESSORY 1. 2. 3. 4.
ONE speaker ONE power cord ONE wired microphone ONE user’s manual
This product operates at 2400 - 2483.5 MHz and is designated only to be used inside a normal household environment. This product is suited for this purpose within all EU counties.
10
SERVICE AND SUPPORT For information: www.lenco.com Lenco offers service and warranty in accordance to European law, which means that in case of repairs (both during and after the warranty period) you should contact your local dealer. Important note: It is not possible to send products that need repairs to Lenco directly. Important note: If this unit is opened or accessed by a non-official service center in any way, the warranty expires. This device is not suitable for professional use. In case of professional use, all warranty obligations of the manufacturer will be voided.
CE MARKING AND RECYCLING Products with the CE marking comply with the EMC Directive (2004/108/EC) and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community. Hereby, STL Group BV, Ankerkade 20 NL 5928 PL Venlo, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of conformity may be consulted at https://lencosupport.zendesk.com/forums/22413161-CE-Documents
This symbol indicates that the relevant electrical product or battery should not be disposed of as general household waste in Europe. To ensure the correct waste treatment of the product and battery, please dispose them in accordance to any applicable local laws of requirement for disposal of electrical equipment or batteries. In so doing, you will help to conserve natural resources and improve standards of environmental protection in treatment and disposal of electrical waste (Waste Electrical and Electronic Equipment Directive).
® All rights reserved
11
