Preview only show first 10 pages with watermark. For full document please download

Pac-106 6-slot Chassis User` S Manual

   EMBED


Share

Transcript

PAC-106 6-SLOT CHASSIS USER’ S MANUAL Copyright Notice This document and product is copyrighted, August 1998, by ICP Electronics Inc. All rights are reserved. No part of this manual may be reproduced, copied, or translated without prior notice to ICP Electronics Inc. The information provided in this document is for reference only. We do not assume any responsibility arising out of the application of the products. This manual is subject to change without any notice. PAC-106, ICP are trademark of ICP Electronics Inc. 1 Table of Contents Chapter 1 Product Information 1.1 General Information 1.2 Product Specifications 1.3 Dimensions Chapter 2 System Setup 2.1 Front Panel of PAC-106 2.2 Rear Panel of PAC-106 2.3 Removing the chassis cover 2.4 Backplane Installation 2.5 Disk Drives Installation 2.6 Replacing the Filter 2.7 Power Supply Installation 2.8 Fan Installation Appendix A Passive Backplane Appendix B Exploded Diagram 2 Chapter 1 Product Information 1.1 General Information PAC-106 IPC chassis is a rugged PC/AT compatible computer designed for the factory floor and other Industrial harsh environment. The PAC-106 features 6 slots Passive Backplane and high reliability AC Input Power Supply ACE-716A. Options available for the power supply are: ACE-716C, ACE-716T. PAC-106 has an unique design for the HDD and FDD installation. It can be used for Desktop or Wall-mounting applications. 1.2 Product Specifications General specification - Construction - Disk Driver - Cooling Fan - Indicator - Dimension : : : : Heavy-duty steel One 3.5” FDD and one 3.5” HDD : Single 32.4 CFM Ball bearing fans Two LEDs to monitor the status of HDD and Power Supply 166x393x175.5 (WxDxH) Passive Backplanes (Optional) BP-6S ISA Bus 6 slots backplane IP-6S PCISA Bus 6 slots backplane PCI-6S PICMG 6 slots backplane Power Supply Optional Power Supply for the PAC-106 are: ACE-716C, ACE-716T 3 Working Environment - Operating Temperature - Relative Humidity - Vibration : : : - Shock - Safety approval : : 0~50°C 5~95% Relative 5-17Hz, 0.1” double amplitude displacement 17-640Hz, 1.5G acceleration peak to peak 10G acceleration peak to peak meet CE, FCC Cooling Fan Single Ball Bearing Cooling Fan Drive Capacity One 3.5” FDD and one 3.5” HDD drive space 4 175.5mm 181.5mm 226.2mm 252mm 276mm 300mm 321.5mm 360mm 393mm 1.3 Dimensions 11.25mm R5mm R2.5mm 166mm 209mm 5 Chapter 2 Installation Procedure The following set up procedures are provided to assist you in installing the system unit, please follow the steps below: 2.1 Front Panel of PAC-106 FILTER COVER RESET SWITCH POWER-LED POWER SWITCH H.D.D-LED 6 2.2 Rear Panel of PAC-106 AC INLET 7 2.3 Removing the chassis cover The cover is mounted by 4 screws at each side of the chassis, remove them and slide the cover to the rear of the chassis. Figure below shows how to remove the chassis cover. 8 2.4 Backplane Installation Figure below illustrates how to install the backplanes on the PAC-106 9 2.5 Disk Drives installation 1. Open the disk drive cover in the front panel 2. Remove the disk drive bay 3. Attach the FDD to the bracket with four screws and connect FDD cable & power cable to the FDD. 4. Attach the HDD to the bracket with four screws and connect a 40-pin flat cable & power cable to the HDD. 10 2.5 Replacing the Filter The filter of the PAC-106 is located at the front end of the chassis. The filter should be removed and cleaned at least once a month to achieve optimum performance. The filter can be removed simply by turn the key-lock to the counter clock-wise direction. Take out the old filter, replace it with the new one if it’ s already worn out. Then close and lock the filter door. 11 2.7 Power Supply Installation 12 2.6 Power Supply Installation PCI-6S 1 P8 P8 7 ACE-716A POWER SUPPLY P9 Brown L Blue N GND E P9 Brown GND Blue POWER SWITCH AC INLET Brown Black Blue Black White White 13 2.8 Fan Installation +12V (Red) ACE-716A POWER SUPPLY GND (Black) 14 133.00 mm 96.00 mm 55.40 mm PASSIVE BACKPLANES 0.00 mm 14.80 mm APPENDIX A 0.00 mm 165.20 mm PCI-6S 254.50 mm 264.50 mm 15 APPENDIX B EXPLODED DIAGRAM 16