Transcript
3
Paint Replacement Tape 4805 Technical Data
February, 2002
Product Description
3M™ Paint Replacement Tape 4805 contains a fluoropolymer backing and an acrylic pressure sensitive adhesive on a removable polyester liner. This tape product provides a high-performance, low surface energy coating solution for paint replacement and specialized surface protection for both indoor and outdoor applications. The tape construction will adhere to a variety of smooth and rough surfaces, is conformable and will stretch and yield allowing application over complex features without discoloration or fracturing. The fluoropolymer tape is inherently resistant to moisture, chemicals, and environmental agents to offer excellent substrate protection as well as providing long term color stability. The tape is available in the following colors: 17925 (white), 37925 (white), 37038 (black), 36270 (medium gray), 36375 (light gray), 36118 (dark gray), and 36173 (dark gray). See the General Information section below and Installation Bulletin for application, benefits, and attributes.
Typical Physical Properties and Performance Characteristics
Notes: 1) The following technical information and data should be considered representative or typical only and should not be used for specification purposes. Metric values are listed in parenthesis. 2) ASTM = American Society for Testing and Materials, FAR = Federal Aviation Regulations
A. Dimensions: Approximate Applied Thickness*:
0.009 inch (0.23 mm)
Standard Roll Size:
24 inch x 72 yd (61 cm x 65.8 m)
Alternate Widths:
1 inch to 24 inch (2.5 cm to 61 cm)
Approximate Weight:
0.064 lbs/ft2 (0.31 kg/m2)
*Excludes the polyester liner that is removed from the tape prior to application.
B. Typical Physical Properties and Performance Characteristics TEST METHOD
UNITS U.S. (SI)
TYPICAL VALUE
Tensile Strength @ Break
ASTM D882
psi (Mpa)
1600 (11)
Elongation % @ Break
ASTM D882
%
500
ASTM D3330 – Method A[1]
oz/in (N/100 mm)
56 (62) 64 (70) 64 (70)
Oxygen Transmission Rate
ASTM D3895[2]
cm3/m2/day (mol/m2/s)
1210 (6.2 x 10-7)
Oxygen Permeance
ASTM D3895[2]
cm3/m2/day/atm (mol/m2/s/Pa)
1210 (6.1 x 10-12)
Water Vapor Transmission Rate
ASTM F1249[3]
g/100 in2/day (g/m2/day)
0.46 (7.2)
PROPERTY
Peel Adhesion @ 70°F (21°C) to: Bare Aluminum ABS Plastic Stainless Steel
[1]
Sample tab was reinforced with Scotch™ 898 Filament Tape. Fluoropolymer film tested without adhesive; Sample area 10.0 cm2; 25.0°C; 40% relative humidity; 100% O2. [3] Fluoropolymer film tested without adhesive; Sample area 10.0 cm2; 37.8°C; 90% relative humidity. [2]
3M™ Paint Replacement Tape 4805 Typical Physical Properties and Performance Characteristics (continued) C. Fluid and Environmental Resistance ENVIRONMENTAL CONDITION UV Aging: ASTM G 154, Cycle 3 ASTM G 155, Cycle 1 Aircraft Interior Fire Protection: FAR 25.853(a) Appendix F Part I (a) (1) (ii) [5]
EXPOSURE
RESULT
500 hours 500 hours
No visible change in dimensions No visible change in color No visible change in gloss[4]
12 Second Vertical Exposure
Self Extinguish Time (sec) = 1 No flaming drips
Distilled Water Immersion
24 hours @ 70°F (21°C)
Unleaded Gasoline
24 hours @ 70°F (21°C)
Diesel Fuel
24 hours @ 70°F (21°C)
JP-8 Jet Fuel
24 hours @ 70°F (21°C)
Motor Oil: SAE 10W-40
24 hours @ 70°F (21°C)
[4]
Adhesion > 56 oz/in (62 N/100 mm) (ASTM D3330 – Method A [1,6]) No visible change in dimensions No visible change in color No visible change in gloss[4]
Samples exposed to the listed environmental conditions; then brought back to ambient conditions, cleaned with isopropyl alcohol and dried before testing. [5] Test conducted with tape applied to fiberglass/epoxy/honeycomb core floor panel. [6] Samples were allowed to dwell for 24 hours prior to immersion in fluids.
-2-
3M™ Paint Replacement Tape 4805 General Information
• 3M™ Paint Replacement Tape 4805 has excellent environmental resistance properties and has been used to isolate and protect substrates from environmental damage and corrosive elements. • Tape 4805 passes FAR 25.853 flame resistance performance requirement for aircraft interiors. • Tape 4805 will adhere and conform to a variety of smooth and contoured surfaces. • Tape 4805 can be used to provide a UV resistant surface coating for indoor and outdoor applications. • Tape 4805 removes cleanly from many substrates.
Safety and Regulatory
• Paint Replacement Tape 4805 is 100% solids and contains no hazardous air pollutants (HAPs), volatile organic component (VOC’s) or materials restricted by regulations or law. Respiratory protection is not required under normal use conditions. • Paint Replacement Tape 4805 has a zero hazard rating for health, fire and reactivity and is rated as flammability class zero. • Paint Replacement Tape 4805 meets US Federal and California regulations for landfillable materials. The product is potentially recyclable, however the pathway is not fully evaluated at this time. • Packaging materials meet US Federal and California regulations for landfillable materials and are recyclable or reuseable. • This product is considered to be an article that does not release or otherwise result in exposure to a hazardous chemical under normal use conditions.
Shipping and Storage
No special/hazardous labeling or packaging required or regulations for air, ground or water shipment for this product. Apply all film within two years of receipt. Keep film in a clean area, away from excessive moisture and out of direct sunlight. Store rolls in the shipping carton. Return partially used rolls to the shipping carton.
-3-
3M™ Paint Replacement Tape 4805 Precautionary Information
Refer to Product Label and Material Safety Data Sheet for health and safety information before using this product. For additional health and safety information, call 1-800-364-3577 or (651) 737-6501.
For Additional Information
For additional information call 1-800-235-2376. For Technical Service assistance, call 651-736-5954. Address correspondence to 3M Aerospace Lab, Technical Service, 3M Center, Building 209-2S-32, St. Paul, MN 55144-1000.
Important Notice
3M MAKES NO WARRANTIES, EXPRESS OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user’s method of application. Please remember that many factors can affect the use and performance of a 3M Engineered Adhesives Division product in a particular application. The materials to be bonded with the product, the surface preparation of those materials, the product selected for use, the conditions in which the product is used, and the time and environmental conditions in which the product is expected to perform are among the many factors that can affect the use and performance of a 3M product. Given the variety of factors that can affect the use and performance of a 3M product, some of which are uniquely within the user’s knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for the user’s method of application.
Limitation of Remedies and Liability
If the 3M product is proved to be defective, THE EXCLUSIVE REMEDY, AT 3M’S OPTION, SHALL BE TO REFUND THE PURCHASE PRICE OF OR TO REPAIR OR REPLACE THE DEFECTIVE 3M PRODUCT. 3M shall not otherwise be liable for loss or damages, whether direct, indirect, special, incidental, or consequential, regardless of the legal theory asserted, including, but not limited to, contract, negligence, warranty, or strict liability. ISO 9002
This Engineered Adhesives Division product was manufactured under a 3M quality system registered to ISO 9002 standards.
3 Aerospace Department Engineered Adhesives Division 3M Center, Building 220-8E-05 St. Paul, MN 55144-1000 www.3m.com/aerospace
Recycled Paper 40% pre-consumer 10% post-consumer
-4-
Printed in U.S.A. ©3M 2002 78-9236-7010-9
(2/02)
