Transcript
Pairing TomTom Remote LINK
Pairing TomTom Remote LINK
You need to pair your TomTom Remote LINK with a TomTom LINK 300/310 before you first use the device. This is required because the Remote LINK transmits your input to the LINK 300/310 without saving the information. There are two ways to pair your Remote LINK with the LINK 300/310 which are described in this document. TomTom WORK certified sales partners can also use the activation tool, visit www.tomtomwork.com/activationtool Important: A Remote LINK can only be paired with one LINK 300/310. If your Remote LINK or the LINK 300/310 has already been paired with another device, both devices need to be reset before pairing with a new device. Instructions on how to reset both devices are described in this document.
Pairing Remote LINK to LINK 300/310 You can pair the Remote LINK with a LINK 300/310 by only using the two devices. 1. Make sure the LINK 300/310 is properly installed in the vehicle. 2. Switch on the ignition. 3. Make sure there are no other vehicles installed with a LINK 300/310 located within a distance of 30 metres. 4. Press any button on your Remote LINK to switch it on. If the LEDs on all three buttons are flashing, then the device is not paired and you need to continue with the next step. Otherwise reset your Remote LINK. 5. Press any two buttons at the same time until you hear a sound.
Remote LINK starts searching for your LINK 300/310 and the blue Connection LED begins to flash rapidly. Searching may take about one minute before a connection is established. Note: To check if a connection has been established press any key.
1
If a connection is established, the blue Connection LED will be on. If you do not use your Remote LINK for 15 seconds, the device will switch off.
If no connection is established, the yellow LEDs on all three buttons will flash and after one minute, the Remote LINK will switch off. To establish a connection, repeat steps 1 to 4.
2
Assigning a Bluetooth address via TomTom WEBFLEET You can assign a Bluetooth address for the connection between a Remote LINK and a LINK 300/310 using TomTom WEBFLEET. This ensures a unique identification for every connection, helping to avoid pairing errors. Requirement: You need access to TomTom WEBFLEET. 1. In TomTom WEBFLEET select the corresponding vehicle under "Vehicles" and click "Configure" in the details panel on the right. 2. Select the "Accessory" tab. 3. Enter the Bluetooth address of the Remote LINK, in the field for Bluetooth address.
4. Switch on the Remote LINK by pressing any key. The yellow LEDs on all three buttons should begin to flash. If not, the Remote LINK needs to be reset. For instructions on resetting the device, read ’Resetting TomTom Remote LINK’. 5. Switch on the ignition. The devices start to pair and the blue LED begins to flash. Pairing may take up to one minute. Note: To check if a connection is established, press any key.
If a connection is established, the blue Connection LED will be on. If you do not use your Remote LINK for 15 seconds, the device will switch off.
3
If a connection is not established, the yellow LEDs on all three buttons will flash and after one minute, the Remote LINK will switch off. To establish a connection, repeat steps 1 to 5.
4
Resetting TomTom Remote LINK If your Remote LINK is paired with a device but not working properly, or if your Remote LINK is paired with the wrong device, you can reset the device to the default factory settings. 1. Press any button on your Remote LINK to switch it on. 2. Press any two buttons at the same time until you hear a sound.
Your Remote LINK switches off. Note: To check if the reset was successful, press any key on your Remote LINK to switch it on.
If the yellow LEDs on all three buttons are flashing, then the reset was successful.
If the blue Connection LED is on, then the reset was not successful. To reset your Remote LINK, repeat steps 1 to 2.
Resetting TomTom LINK 300/310 If you want to pair your LINK 300/310 to a different Remote LINK, you need to reset the LINK 300/310. To reset the LINK 300/310, delete the Bluetooth address for the Remote LINK for the corresponding vehicle in the configuration dialogue in TomTom WEBFLEET and click "Save changes".
5
