Transcript
Parts Included
Flat Panel Tilt Mount
Tools and Components included in your package: Bolts
SAE Washers
Fender Washers
Screw Locks (F) 5/32 Allen Wrench
Machine Screws 4 pc each 4 mm x 16 mm
7/16" Nuts
Key
Carriage Bolts
6 mm x 16 mm Mount (D)
Inner Rails (A)
Outer Rails (B)
5 mm x 16 mm
Installation Guide
7 mm x 16 mm Rail Plate (C) (attached to Mount)
Cover Plate (E)
Tools Needed for Install: Pencil
Drill with 1/4" Bit
Wrench with 9/16" & 7/16" Socket
Philips Screwdriver
Level
Important Warnings and Cautions Warning - Failure to read, understand and follow instructions can result in serious injury, damage to equipment or voiding equipment warranty. Warning - Improper installation can result in serious personal injury or death. Ensure that the mounting surface can support a weight factor of four times the combined total weight of the equipment and the mount. If not, reinforcement of the mounting surface will be necessary before installing the mount. Warning - It is the installer's responsibility to make sure that the mounting surface and the subsurface is free and clear of all electrical wires, plumbing and gas pipes. Failure to provide adequate clearance of all electrical wires and pipes can result in serious personal injury or death. Warning - Mount and equipment exceeding a combined weight of 50 lbs can result in damage to the support structure, the mount, the equipment and may cause personal injury. Warning - Business Machine Security, Inc. does not warrant its mounts against damage caused by the end use of its mounts for any purpose other than for the purpose for which it has been designed. Warning - Business Machine Security, Inc. is not responsible for damage, or injury that may result in the use of any unauthorized modifications or attachment. Warning - Proper safety gear (Goggles, Glasses & Gloves) and practices should be adhered to at all times throughout the installation process. Warning - Do not install the mount near any heat source or air conditioning vent which may be prone to vibration. Warning - Maximum load capacity 50 lbs. Warning - Do not expose to extreme temperatures.
Made in USA
www.LocDown.com www.Anchorpad.com
800.872.9562
1 Attaching Receiver Tray to Wall *Rail Plate Not Shown
3. Measure distance between Inner Rails (A) from mounting screw to mounting screw, align Outer Rails (B) to corresponding location on Rail Plate (C), insert Carriage Bolts through aligned holes from back and fasten Nuts with a 7/16" wrench.
Wall Stud
D E
2 Attaching Rails... Continued
3 Attaching TV to Mount B
D Pilot Holes
1
F 1. Remove Cover Plate (E) and locate center of wall studs. (NOTE: If studs are not 16" on centers, backing or internal wall plate may be needed). 2. Place level on top of Mount (D) and determine location of holes. Mark hole location with a pencil. 3. Drill 1/4" pilot holes at each marked location on wall. Align Mount (D) to wall and insert lag bolts and SAE washers into pilot holes. 4. Loosely tighten lag bolts. Adjust Mount (D) so it is level, then securely tighten the lag bolts. Reattach Cover Plate (E) and Place Cylinder Lock (F) into housing and turn clockwise to secure. Do not over tighten.
2 Attaching Rails Distance
Distance
3 2
A
B
A
Side View
1. Hold TV firmly at each side and align the attached Inner Rails (A) with the Outer Rails (B). 2. Slide the top end of the Inner Rails (A) into the Outer Rails (B) then push bottom in and slowly slide down into place. 3. Place Cylinder Lock (F) into housing and turn clockwise to secure. Do not over tighten.
4 Adjusting Position on Tilt Arm
(it is recommended that you remove the TV before making adjustments) Pivot Point
C A Attaching to T.V.
Attaching to Rail Plate
2. Support TV with one hand while the other slowly loosens screw until mount is able to adjust. (**Do not loosen screw too quickly or mount will fall forward and may cause damage to TV.)
B
1. Turn TV upside down and place it flat on a soft cloth or packaging material. Be sure that area is a level and sturdy surface. 2. Align Inner Rails (A) (lock at bottom) with VESA hole pattern (if applicable) on back of TV, place Fender Washers over each mounting insert and attach the correct length screw with Phillips head screw driver. (DO NOT OVER TIGHTEN as this can cause serious damage to the TV)
1. Insert the provided 5/32" Allen Wrench into adjustment screw at base of mount.
Adjusting Screw
3. Adjust mount to desired angle and gently tighten screw. Parts Description on Back Page
