Parts Replacement/maintenance

Transcript

TB-1018 Parts Replacement/Maintenance Chart 1 – Air Cap ORDER NO. FOR AIR CAP NUMBER ON CAP RECOMMENDED INLET PRESSURE BAR/PSI AIR FLOW LPM/SCFM 703899 (HVLP) HV20 1.0 – 1.3 bar 14 – 18 psi 317 – 368 LPM 11.2 – 13.0 SCFM NOTE 1: Guns with HVLP caps must not exceed 0.7 bar (10 psi) air cap pressure with gun fully triggered. (Aproximately 24 psi gun inlet pressure.) (See accessories for air cap test kit which is available to set the exact cap pressure.) NOTE 2: When removing air cap from retaining ring, don’t remove slip ring (2) or retaining ring seal (5) from retaining ring. Damage to the parts may occur. Slip ring and retaining ring seal are not available as replacements. Simply wipe parts clean and reassemble with new or clean air cap. Chart 2 – Fluid Nozzles & Fluid Needles NO. ON FLUID NOZZLE TIP SIZE I.D. (MM) NO. ON FLUID NEEDLE (TO MATCH FLUID NOZZLE) ORDER NO. FOR NOZZLE & NEEDLE SET SN-37-11 1.1 SN-38-11 702711 SN-37-12 1.2 SN-38-12 702712 SN-37-13 1.3 SN-38-13 702713 SN-37-14 1.4 SN-38-14 702714 SN-37-15 1.5 SN-38-15 702715 NOTE: When replacing the fluid nozzle or fluid needle, replace both at the same time. Lightly lubricate the threads of the fluid nozzle before reassembling. Torque to 18–20 Nm (13–15 ft-lbs). Don’t over tighten the fluid nozzle. Use 10 mm wrench supplied with gun. 11 TB-1018 19 14 15 1 3 1 2 18 17 16 25 20 21 24 23 22 11 6 2 1 5 4 3 10 9 8 37 7 Fluid Nozzle Torque to 18–20 nm (13–15 ft-lbs) 7 26 27 40 39 28 29 44 45 42 33 32 30 REF. NO. 31 DESCRIPTION 34 Air Inlet – Torque to 20 nm (15 ft-lbs) Use medium strength thread sealant (i.e. Devcon #2242 blue, or equivalent) on threads 36 PART NO. 43 41 46 35 QTY REF. NO. DESCRIPTION PART NO. QTY 1 Air Cap Retaining Ring 1 *26 Needle Packing 1 2 Slip Ring 1 *27 Packing Spring 1 3 Air Cap 1 *28 Packing Nut 4 Air Cap Retaining Clip 1 29 Packing, Spring & Packing Nut Kit 5 Retaining Ring Seal 1 30 Air Valve Body 1 6 Air Cap & Ring See Chart 1, p.11 1 31 Air Valve Cage 1 32 Air Valve Poppet 1 33 Air Valve Spring 1 34 Air Valve Spring Pad 1 35 Air Valve Seal 36 Air Valve Assembly 191972 7 Air Cap Retaining Ring & Seals 703896 1 8 Fluid Nozzle See Chart 2, p.11 1 9 *10 11 *12 Air Separator 1 Air Separator Seal (kit of 2) 702726 1 Air Separator & Seal Kit 703900 1 Body Bushing Gasket 1 13 Body Bushing 1 14 Body Bushing & Gasket 702728 1 15 Fluid Needle See Chart 2, p.11 1 *16 Needle Spring 1 *17 Needle Spring Pad 1 18 Fluid Adjusting Knob 1 19 Fluid Adjusting Knob, Spring, & Pad Kit *20 21 *22 23 *24 25 12 38 703897 1 *37 38 *39 1 702731 1 702732 1 Trigger 1 Trigger Stud 1 40 Trigger, Stud & Screw Kit 702733 41 Plug 42 Air Inlet 702734 1 1 43 Colour ID Ring Kit (4 Colours) 702735 1 44 Gun Body 45 Air Valve Service Tool (only included with Air Valve Assembly 36) 46 Air Adjusting Valve (optional) 1 1 702737 1 OTHER SALABLE PARTS / ACCESSORIES 1 Spreader Valve Body 1 Wrench (10 & 14mm) 702740 O-ring 1 192229 Spreader Valve Adjusting Knob 1 Seal and Pin Kit (Kit of 5) (Items 20, 22 and 24.) Spreader Valve Assembly 1 Trigger Stud Screw (T20 Star) Retaining Clip Spreader Valve Pin 1 1 703898 1 * The TEKNA Spray Gun Repair Kit (702736) contains all the parts indicated with an asterisk.