Transcript
Video • Data
Passive UTP Transceiver Hub Installation Guide Models Include:
HubWayH16 - Sixteen (16) Camera Channels
Rev. 121710
More than just power.TM
Overview: Altronix HubWayH16 Passive UTP Transceiver Hub transmits UTP video, RS422/RS485 data over a single CAT-5 or higher structured cable. Unit provides 16 camera channels in a space saving 1U EIA 19” rack mount chassis. Video transmission range is up to 750 ft. max. per channel. Units are compatible with fixed cameras or PTZs.
Video:
Specifications: Accessories:
• Sixteen (16) channels of video over twisted pair up to a distance of 750 f t. per channel. • Sixteen (16) 75 ohm video outputs.
Data: • RS422/RS485 data inputs.
Features:
• HubWayAv2 - Interfaces with all HubWay and HubSat UTP Transceiver Hubs for 24VAC/12VDC fixed cameras or PTZs (based on power supply rating). • HubWayAvP - Interfaces with HubWayH16 Passive UTP Transceiver Hub for 24VAC/12VDC fixed cameras (based on power supply rating).
• 1U rack mount chassis for use in standard EIA 19” rack.
Installation Instructions: 1. Secure the unit in a rack (Fig. 5, pg. 6) (unit should be spaced at least 3” from any video monitors). 2. Connect the BNC video outputs for HubWayH16 Channels 1-16 to the corresponding video inputs on the head end equipment (DVR) (Fig. 1d, pg. 3). 3. Connect external power source (AC or DC power supply) to the individual channel terminals marked [Power] (Fig. 1b, pg. 3). Connecting Fixed Cameras (Fig. 3a, pg. 5): 1. Set switch of the corresponding channel on the rear of HubWayH16 to [PWR] (Fig. 1e, pg. 3). Warning: To avoid equipment damage do not connect PTZs to channels selected for POWER (PWR) only. 2. Connect HubWayAvP Video Balun/Combiner at camera to the HubWayH16 unit utilizing CAT-5 or higher structured cable. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked [Channel 1-16] of the HubWayH16 (Fig. 1c, pg. 3). Plug the RJ45 connector at the opposite end of the structured cable into the RJ45 jack of the Video Balun/Combiner located at the camera (Fig. 2a, pg. 4). Note: Repeat steps 1-2 for each additional fixed camera (Channels 2-16). Connecting PTZ Cameras (Fig. 3b, pg. 5): 1. Connect the RS422/RS485 output of the head end equipment (DVR) to the individual terminals marked [+ DATA --- ] of the HubWayH16 unit (polarity must be observed) (Fig. 1a, pg. 3). Note: The Data input terminals of the HubWayH16 must be wired in parallel for proper operation. 2. Set switch of the corresponding channel on the rear of HubWayH16 to [PWR/DATA] (Fig. 1e, pg. 3). 3. Connect HubWayAv2 Video Balun/Combiner at camera to the HubWayH16 unit utilizing CAT-5 or higher structured cable. Plug the RJ45 connector at one end of the structured cable into the RJ45 jack marked [Channel 1-16] of the HubWayH16 (Fig. 1c, pg. 3). Plug the RJ45 connector at the opposite end of the structured cable into the RJ45 jack of the Video Balun/Combiner located at the camera (Fig. 2b, pg. 4). Note: Repeat steps 1-3 for each additional PTZ camera (Channels 2-16).
WARNING: To reduce the risk of fire or electric shock, do not expose the unit to rain or moisture. This installation should be made by qualified service personnel and should conform to all local codes.
- 2 -
HubWayH Passive Hub Unit
HubWayH Passive Hub Unit
-3-
Front
Rear
9
1
12
4
16
PWR DATA
PWR DATA
8
POWER
PWR
PWR
CHANNEL DATA + ---
PWR DATA
15
PWR DATA
7
POWER
1d - BNC Connector: Video outputs to head end equipment (DVR).
DATA + ---
PWR
PWR
CHANNEL
1b - Individual Power Input: External AC or DC power input.
1a - Data Input: RS422/ RS485 input from head end equipment (DVR) for PTZ control.
Fig. 1
DATA + ---
PWR
PWR
CHANNEL DATA + ---
PWR DATA
13
PWR DATA
5
POWER
PWR
PWR
CHANNEL
1e - Individual Power & Data or Power Switches: Video outputs to head end equipment (DVR).
14
PWR DATA
PWR DATA
6
POWER
1c - Channels 1-16: CAT-5 or higher structured cable to Video/Balun Combiners at cameras 1-16.
8
16
5
13 DATA + ---
PWR DATA
12
PWR DATA
4
POWER
PWR
PWR
CHANNEL
DATA + ---
PWR DATA
11
PWR DATA
3
POWER
PWR
PWR
CHANNEL
DATA + ---
PWR DATA
10
PWR DATA
2
POWER
PWR
PWR
CHANNEL
DATA + ---
PWR DATA
9
PWR DATA
1
POWER
PWR
PWR
CHANNEL
Video Balun/Combiners: Fig. 2 Fig. 2a
Power to Camera
Cat5 back to HubWay or HubSat
Data to Camera
Video from Camera
Power to Camera
Fig. 2b Cat5 back to HubWayH16
Power to Camera
Video from Camera
Fig. 2c
VIDEO
Commercial CCTV Accessory 3C03
HubWayDv VIDEO BALUN/COMBINER Refer to the HubWay Video Balun/Combiner Installation Guide Rev. 123008 RJ45
RJ45 Jack
To BNC Connector of Camera
Structured Cable from HubWayH16
DATA 12VDC + -- -- +
Wire Connectors
Red Power LED + 12VDC Power -- to Camera -- Data to + Camera
- 4 -
HubWayH Passive Hub Unit
Typical Application: Fig. 3 Fig. 3a
External Rack Mount 12VDC or 24VAC Power Supply
Head end Equipment (DVR)
HubWayH16 Rear Panel Connections
PWR DATA
PWR
1
HubWayH16 Front Panel Connections
1
4
DATA + ---
POWER
CHANNEL
CAT-5
Video Balun Combiner Video/ Power
Fig. 3b
External Rack Mount 12VDC or 24VAC Power Supply
Head end Equipment (DVR)
HubWayH16 Rear Panel Connections
PWR DATA
1
12VDC or 24VAC Fixed Camera
PWR
HubWayH16 Front Panel Connections
1
4
DATA + ---
POWER
CHANNEL
Head end Equipment (DVR)
CAT-5
Video Balun Combiner Video/ Data/ Power
HubWayH Passive Hub Unit
12VDC or 24VAC PTZ Camera
-5-
Rack Mount Chassis Mechanical Drawing & Dimensions (H x W x D approximate): 1.625” x 19.125” x 2.498” (41.3mm x 486mm x 63.5mm) REAR
Fig. 4
19.0” (482.6mm) PWR DATA
PWR
PWR DATA
PWR
8
1.696” (43.08mm)
PWR DATA
PWR
PWR DATA
PWR
7
15
16
PWR DATA
PWR
PWR DATA
PWR
6
PWR DATA
PWR
PWR DATA
PWR
5
14
PWR DATA
PWR
PWR DATA
PWR
4
13
PWR DATA
PWR
PWR DATA
PWR
3
12
PWR DATA
PWR
PWR DATA
PWR
2
11
PWR DATA
PWR
PWR DATA
PWR
1
10
9
17.10” (434.34mm)
2.498” (63.45mm)
3.0225” (76.77mm)
TOP & BOTTOM
1
5
4
1.696” (43.08mm) 9
8
FRONT 13
12 DATA + ---
POWER
CHANNEL
DATA + ---
POWER
CHANNEL
DATA + ---
POWER
CHANNEL
DATA + ---
POWER
CHANNEL
16 DATA + ---
POWER
CHANNEL
DATA + ---
POWER
CHANNEL
DATA + ---
POWER
CHANNEL
DATA + ---
POWER
CHANNEL
The lightning flash with arrow head symbol within an equilateral triangle is intended to alert the user to the presence of an insulated DANGEROUS VOLTAGE within the product’s enclosure that may be of sufficient magnitude to constitute an electric shock. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance. CAUTION: To reduce the risk of electric shock do not open enclosure. There are no user serviceable parts inside. Refer servicing to qualified service personnel.
Rack Mount Installation: 1- Place unit into desired EIA 19” rack position and secure with mounting screws (not included) (Fig. 5). Fig. 5
- 6 -
HubWayH Passive Hub Unit
Notes:
HubWayH Passive Hub Unit
-7-
Notes:
Altronix is not responsible for any typographical errors. 140 58th Street, Brooklyn, New York 11220 USA, 718-567-8181, fax: 718-567-9056 website: www.altronix.com, e-mail:
[email protected], Lifetime Warranty, Made in U.S.A. IIHubWayH16 E20N - 8 -
MEMBER HubWayH Passive Hub Unit
