Transcript
Installation Guide Case components Front door with lock
140mm fans x 2 Power switch Reset switch
Fan sped control switch
Multi-media ports
5.25" mounting bezel
Removable 140mm fan cover Rubberized grommets for liquid cooling tubing 120mm fan Slide out M/B tray
Removable 3.5” HDD module (1) (For 3.5" HDD x 3 )
140mm fans x 3 and washable air filter
Removable 3.5” HDD module (2) (For 3.5" HDD x 4, 2.5" HDD x 2)
VGA card support column Patented tool-less PCI add-on card holder Patented tool-less PSU mounting bracket
Front panel key is in the accessories box
Hardware list
Extra quantities are spare parts.
Box (1) for spare parts
Buzzer (1)
Thumb screw (24) for 3.5" HDD
Screw #6 - 32*9.5 (16) for 3.5" HDD
Mounting bracket (1) for SSI CEB/EEB M/B
USB 3.0 to USB 2.0 converter (1)
Rubber ring (24) for 3.5" HDD
Screw (12) for converter & spare parts
Stand off bolt (3) for motherboard (spare parts)
Cable ties (3)
Screw M3*9.5 (8) for 2.5" HDD
PCI card holder/A (11)
Nut (3) for stand off
Thumb screw (12) for ODD
Anti-vibration rubber-rings for 2.5" HDD (8)
PCI card holder/B (4)
Long thumb screw (3) for motherboard mount
Screw (4) for PSU mounting
Bracket (1) for power supply mounting
Thumb screw (11) for PCI card holder
Short thumb screw (9) for motherboard mount
Screw driver (1) to ass’y motherboard
Guide to open left and right side pnels
Motherboard installation !
Note: For hard to reach areas use long thumb screws.
! !
2
Remove six thumb screws.
Slide the panel backward to release.
The oval hole on M/B tray designed for special server boards. Please use a nut to hold the copper bolt in place.
1
1. Remove two thumb screws. 2. Slide the panel forward to release.
for SSI CEB/EEB
Secure the spacing bolts to the motherboard tray. Place the M/B on the copper bolt and secure with thumb screws.
3.5” HDD module (1) installation
Remove four thumb screws.
Pull to release.
Install the screws to the HDD with anti-vibration rubber rings.
3.5” HDD module (2) installation
Slide the HDD into the HDD cage.
Close the gate to secure the HDD.
2.5” HDD installation
2 1
Remove eight thumb screws.
Pull to release.
Insert HDD, secured with thumb screws.
Install the screws to the HDD with anti-vibration rubber rings.
Follow the arrows: place the HDD over the locking points, and slide to secure. C50.P80N0.00E-1
PCI add-on card installation
ODD installation
1 2 1 1
Remove 5.25" mounting bezel.
Push the CD-ROM into the ODD tray and fasten four thumb screws to secure.
Push to release
2
2 Open the aluminum latch to remove the PCI slot bracket.
VGA card pillar installation guide
Push the card into the PCI slot, close the aluminum latch to secure the card.
Cable management
L
Insert PCI card holder/A
Use PCI card holder/B for thick VGA cards.
Fan speed control switch
PSU installation
Place the PSU on the stand, Place the PSU bracket into and push against the rear panel. slot as shown.
Lock the PSU bracket to secure the PSU.
Remove air filter
* For transportation, please place screw to secure the PSU
Supports liquid cooling systems
Washable air filter in the front door
Easy clean air filter .
Washable air filter in the bottom
Slide the air filter to remove.
Pull to release.
I/O port installation EAR
Cable installation guide E-SATA SATA Cable
E-SATA
USB 3.0
USB 3.0 USB 3.0
MIC
Supports motherboard USB 3.0 20 Pin header
Removable top panel
WHITE GRAY
GROUND Reset PLED-
WHITE BLUE WHITE NC GREEN
PLED+ IDE_LEDWHITE IDE_LED+ ORANGE
HD AUDIO BLUE 10 BLACK PURPLE 8 YELLOW 6 BROWN 4 RED 2
GROUND PWR
9 7 5 3 1
GREEN KEY ORANGE N.C. GND+H.S. TUBE
Speaker +5V
BLACK NC NC RED
POWER SW RESET SW POWER LED H.D.D LED
SPEAKER
USB 3.0 to USB 2.0 converter Pin19
Pin1
USB
Pin11
VCC RED D- WHITE D+ GREEN GND BLACK
RED WHITE GREEN BLACK KEY
VCC DD+ GND
Pin10
Notice:
To change the door's swinging hinge from right-side to left-side, visit www.lian-li.com for installation guide. C50.P80N0.00E-2
