Transcript
Model PD0922J7575D2 Rev E
Ultra Low Profile 0805 Power Divider 75Ω to 75Ω Description The PD0922J7575D2 is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package and is ideal for high volume manufacturing while delivering higher performances than traditional printed and lumped element solutions. It has been designed for the following markets: DVB-S, GSM, DCS, PCS, WCDMA, GPS, 802.11a+g, Bluetooth, and Zigbee USA. The PD0922J7575D2 is matched to 75Ω and has a height profile of 0.8 mm. A two section Wilkinson design results in increased isolation performance. Two external resistors are required for operation. Components are available on tape and reel for high volume manufacturing pick and place. All Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and Y thermal o coefficient of expansion (CTE) of 17 ppm/ C.
Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°°C)
Features: • • • • • • • • • • •
950 – 2150 MHz 16 dB Isolation (output ports) Good Return Loss 0.8mm Height Profile 75Ω Outputs/Inputs External resistors required Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant
Parameter
Min.
Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling Operating Temperature
950
Typ. 75 75 11 0.8 0.4 2 16
9.5
14
Max
Unit
2150
MHz Ω Ω dB dB dB Degrees dB Watts ºC
1.0 0.7 3 2 +85
-55
* Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC)
Outline Drawing Top View (Near-side) .079±.004 [2.00±0.10]
Side View
Bottom View (Far-side) 2X .026 [0.65]
.033±.002 [0.84±0.05]
.039 [0.98]
1
2
3 6X .009 [0.22]
.049±.004 [1.25±0.10] Orientation Marker Denotes Pin Location
Dimensions are in Inches [Millimeters] Mechanical Outline
Orientation Marker Denotes Pin Location Pin 1 2 3 4 5 6
Designation Output 1 Input Mid 2 Mid 1 GND Output 2
6 5 6X .012 [0.30]
4
Tolerances are Non-Cumulative
Available on Tape and Reel for Pick and Place Manufacturing.
USA/Canada: Toll Free: Europe:
(315) 432-8909 (800) 411-6596 +44 2392-232392
Model PD0922J7575D2 Rev E
Typical Broadband Performance: 500 MHz. to 8.0 GHz. Insertion Loss 0
-3
-3
-6
-6 -9
-12
-12
-15
-15
0 -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 8000
7500
7000
6500
6000
5500
5000
4500
4000
3500
3000
-36 2500
7000
7500
8000
7000
7500
8000
5000
5000
4500
4000
3500
3000
2500
2000
1500
Frequency [MHz]
Isolation
2000
1000
8000
7500
7000
6500
6000
5500
5000
4500
-20 4000
-15
-2 3500
-1.5
3000
-10
2500
-1
2000
-5
500
0
-0.5
1500
6500
5
0
1500
6000
0.5
1000
6500
10
1000
6000
1
500
5500
15
deg
1.5
Frequency [MHz]
[dB]
4500
Phase Balance 20
500
[dB]
Amplitude Balance
Frequency [MHz]
(315) 432-8909 (800) 411-6596 +44 2392-232392
4000
Frequency [MHz]
2
USA/Canada: Toll Free: Europe:
5500
Frequency [MHz]
3500
3000
2500
500
8000
7500
7000
6500
6000
5500
5000
4500
4000
3500
-36 3000
-33
-36 2500
-30
-33 2000
-27
-30
1500
-24
-27
1000
-21
-24
2000
-18
-21
1500
-18
1000
[dB]
-9
500
[dB]
Return Loss - Input 0
Available on Tape and Reel for Pick and Place Manufacturing.
Model PD0922J7575D2 Rev E
Typical Performance: 900 MHz. to 2200 MHz. Insertion Loss
-3
-0.3
-6
-0.6
-9
-0.9
-12
-1.2
-15
-1.5
1.5
15
1
10
0.5
5
2200
2100
2000
1900
1800
2200
2100
2000
1900
1800
1700
1600
1500
1400
1300
900
2200
2100
2000
1900
1800
1700
-20 1600
-2 1500
-15
1400
-1.5
1300
-10
1200
-1
1100
-0.5
1200
0 -5
1100
0
1000
deg
20
1000
1700
Phase Balance
Amplitude Balance 2
900
1600
Frequency [MHz]
Frequency [MHz]
[dB]
1500
1400
1300
900
2200
2100
2000
1900
1800
1700
1600
1500
-3.6 1400
-3.3
-36 1300
-3.0
-33 1200
-2.7
-30
1100
-2.4
-27
1000
-2.1
-24
1200
-1.8
-21
1100
-18
1000
[dB]
0.0
900
[dB]
Return Loss - Input 0
Frequency [MHz]
Frequency [MHz]
Isolation 0 -3 -6 -9 -12 -18 -21 -24 -27 -30 -33 2200
2100
2000
1900
1800
1700
1600
1500
1400
1300
1200
1100
1000
-36 900
[dB]
-15
Frequency [MHz]
Available on Tape and Reel for Pick and Place Manufacturing.
USA/Canada: Toll Free: Europe:
(315) 432-8909 (800) 411-6596 +44 2392-232392
Model PD0922J7575D2 Rev E
Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical o and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/ C. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD0922J7575D2 is a Wilkinson power divider, external 0402 150Ω and 300Ω resistors must be mounted in locations R1 and R2 respectively, as shown in the Figure below.
Pad Footprint w/ 0402 Resistor Locations 3X Transmission Line 6X .014 [0.35]
6X .013 [0.33]
R1
4X .012 [0.30]
.026 [0.66]
Plated thru hole to ground Circuit Pattern Footprint Pad (s) Solder Resist Dimensions are in Inches [Millimeters] Mounting Footprint
USA/Canada: Toll Free: Europe:
(315) 432-8909 (800) 411-6596 +44 2392-232392
Available on Tape and Reel for Pick and Place Manufacturing.
R2
Model PD0922J7575D2 Rev E
Packaging and Ordering Information Parts are available in reel and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information.
ØA
ØC
ØD
QUANTITY/REEL
4000
TABLE 1 REEL DIMENSIONS (inches [mm]) ØA 7.00 [177.8] B 0.32 [8.0] 2.0 [50.8] ØC ØD 0.512 [13.0]
B
Available on Tape and Reel for Pick and Place Manufacturing.
USA/Canada: Toll Free: Europe:
(315) 432-8909 (800) 411-6596 +44 2392-232392
Model PD0922J7575D2 Rev E
USA/Canada: Toll Free: Europe:
(315) 432-8909 (800) 411-6596 +44 2392-232392
Available on Tape and Reel for Pick and Place Manufacturing.
