Transcript
ATC Air Traffic Control - Catalogue 13
Via Senatore Simonetta,26 20867 Caponago (MB) - Italy tel.: +39 02.95.96.11 fax +39 02.95.96.13.11 e-mail:
[email protected] www.sira.mi.it
history SIRA SIRA is a privately owned company, founded in 1977 by a group of technicians active in the telecommunication field and specialized in RF technology. Sira has 11,000 sq.meters of manufacturing and support facility based in Caponago (MI) Italy. SIRA is a customer oriented company, which has adopted the philosophy of working together with its customers to meet the critical technical requirements for their systems with an attitude of enthusiasm and concern in order to provide the best results in the final products. This approach has given Sira a position of leadership in its field. Sira products are designed and manufactured in accordance with the particular international standards in force in the area. As a major position of its cross revenues, Sira has been investing in research and development, quality and reliability control and products safety in the RF field. This policy of investments has provided Sira with an extremely high level of experience in its field: there are Sira installations in more than 80 countries in the world.
1
quality
SIRA’s aim is to give to all its customers reliable products and services with the highest quality standards, this ambitious goal is achieved mainly by means of an integrated management system (Quality-Safety-environment) and is certified according to the norms UNI EN ISO 9001 (2000) and UNI EN 14001 (1996). The enhancement of company efficiency through the continuous improvement of the operative quality of the internal functions (effectiveness), the reduction of defects on sold products and the notable attention to the quality culture at all company levels have become SIRA’s fundamental cares. Moreover SIRA is committed in a thorough policy of environmental protection: a training and information process on all personnel is continuously carried out in order to grant a responsible management of all the activities in a special respect of the environment. For instance, the development and the implementation of new technologies, products and production processes is carried out with a thorough control for a rational use of energetic sources and of raw materials, minimizing the production of waste and the use of non-renewable resources, everything with the aim of keeping environmental impact on air and water as lowest as it is possible. For all SIRA’s activities it is fundamental to oppose the conditions of life and work which are against the health of the workers, as well as promoting freedom principles and self-respect for any human being. An extract from SIRA’s ethic code states that “Sira refuses any discrimination based on sex, race, languages, personal and social conditions, religion and political choices” and to this aim Sira promotes a working environment that, inspired to the principles of respect, fairness and collaboration, is meant to support the involvement of all Employees and Contributors giving the common sense of responsibility in reaching all the Company goals.
2
index
VHF and UHF broadband omnidirectional antenna Vertical Polarization
5
Multi dipole UHF omnidirectional antenna Vertical Polarization
11
Multi dipole VHF omnidirectional antenna Vertical Polarization
23
Multi dipole VHF/UHF omnidirectional antenna Vertical Polarization
29
Anti-Icing System
37
3
VHF and UHF broadband omnidirectional antenna Vertical Polarization
TBT 02-360/V
7
TBT 02-360/U
9
VHF and UHF broadband omnidirectional antenna Vertical Polarization TYPE NO.
TYPE
# INPUTS
HEIGHT
ANT/TBT 02-360/U
VPol Omni
225-400 MHz
360°
2 dBi
1xNf
946 mm
ANT/TBT 02-360/V
VPol Omni
108-156 MHz
360°
2 dBi
1xNf
1392 mm
5
TBT 02-360/V
GROUND TO AIR COMMUNICATION OMNIDIRECTIONAL ANTENNA
FEATURES vertical polarization broadband 108 ÷ 156 MHz 2 dBi gain omnidirectional pattern
ELECTRICAL DATA TYPE FREQUENCY RANGE IMPEDANCE CONNECTOR MAX POWER VSWR POLARIZATION GAIN HALF POWER BEAMWIDTH LIGHTNING PROTECTION
TBT 02-360/V 108 ÷ 156 MHz 50 ohm NF 500 W ≤ 2.0 ≤ 1.6 (118÷137 MHz) Vertical 2 dBi E-plane 75° H-plane 360° (omni ± 0.3 dB) All metal parts of the antenna, including the mounting kit and the inner conductor, are DC grounded
RADIATION PATTERNS (Mid Band) 0
270
90 10 6 3 1 dB 180
H-plane
MECHANICAL DATA DIMENSIONS WEIGHT (braket excluded) WIND SURFACE WIND LOAD (wind speed 150 km/h) MAX. WIND VELOCITY ICING PROTECTION RADOME COLOUR MOUNTING PACKING
DS 921.510.294/04
1392 x ø 82 mm 7 kg 0.11 m2 120 N 240 km/h Full radome Grey (std.), other on request On pole 1570 x 190 x 190 mm
0
270
90 10 6 3 1 dB 180
E-plane
Specifications are subject to change without prior notice
7
ADDITIONAL INFORMATION Mounting:
The antenna can be attached laterally at the tip of a tubular mast of 60-120 mm diameter with two brackets supplied with the antenna (connecting cable runs outside the mast).
Materials: Radiator: Radome: Base: Mounting kit, screws and nuts:
Aluminium. Fiberglass, colour: Grey. Weather-proof aluminium. Stainless steel.
PLEASE NOTE: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufactures must be obeyed. DS 921.510.294/04
Specifications are subject to change without prior notice
8
TBT 02-360/U
GROUND TO AIR COMMUNICATION OMNIDIRECTIONAL ANTENNA
FEATURES vertical polarization broadband 225 ÷ 400 MHz 2 dBi gain omnidirectional pattern
ELECTRICAL DATA TYPE FREQUENCY RANGE IMPEDANCE CONNECTOR MAX POWER VSWR POLARIZATION GAIN HALF POWER BEAMWIDTH LIGHTNING PROTECTION
TBT 02-360/U 225 ÷ 400 MHz 50 ohm NF 300 W ≤ 2.0 Vertical 2 dBi E-plane 75° H-plane 360° (omni ± 0.5 dB) All metal parts of the antenna, including the mounting kit and the inner conductor, are DC grounded
RADIATION PATTERNS (Mid Band) 0
270
90 10 6 3 1 dB 180
H-plane
MECHANICAL DATA DIMENSIONS WEIGHT (braket excluded) WIND SURFACE WIND LOAD (wind speed 150 km/h) MAX. WIND VELOCITY ICING PROTECTION RADOME COLOUR MOUNTING PACKING
DS 921.510.316/03
946 x ø 82 mm 6 kg 0.08 m2 85 N 240 km/h Full radome Grey (std.), other on request On pole 1125 x 190 x 190 mm
0
270
90 10 6 3 1 dB 180
E-plane
Specifications are subject to change without prior notice
9
ADDITIONAL INFORMATION Mounting:
The antenna can be attached laterally at the tip of a tubular mast of 60-120 mm diameter with two brackets supplied with the antenna (connecting cable runs outside the mast).
Materials: Radiator: Radome: Base: Mounting kit, screws and nuts:
Aluminium. Fiberglass, colour: Grey. Weather-proof aluminium. Stainless steel.
PLEASE NOTE: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufactures must be obeyed. DS 921.510.316/03
Specifications are subject to change without prior notice
10
Multi dipole UHF omnidirectional antenna Vertical Polarization
TBT 02-360/U2
13
TBT 02-360/U3
15
TBT 02-360/U4
17
TBT 02-360/U5
19
TBT 02-360/U6
21
Multi dipole UHF omnidirectional antenna Vertical Polarization TYPE NO.
TYPE
# INPUTS
HEIGHT
ANT/TBT 02-360/U2
VPol Omni
225-400 MHz
360°
2 dBi
2xNf
2690 mm
ANT/TBT 02-360/U3
VPol Omni
225-400 MHz
360°
2 dBi
3xNf
3730 mm
ANT/TBT 02-360/U4
VPol Omni
225-400 MHz
360°
2 dBi
4xNf
4785 mm
ANT/TBT 02-360/U5
VPol Omni
225-400 MHz
360°
2 dBi
5xNf
5810 mm
ANT/TBT 02-360/U6
VPol Omni
225-400 MHz
360°
2 dBi
6xNf
6850 mm
11
TBT 02-360/U2
GROUND TO AIR COMMUNICATION OMNIDIRECTIONAL ANTENNA
FEATURES vertical polarization broadband 225 ÷ 400 MHz 2 dBi gain omnidirectional multi-element antenna consisting of two indipendently fed UHF dipoles
ELECTRICAL DATA TYPE FREQUENCY RANGE IMPEDANCE CONNECTOR MAX POWER VSWR POLARIZATION GAIN HALF POWER BEAMWIDTH DECOUPLING LIGHTNING PROTECTION
TBT 02-360/U2 225 ÷ 400 MHz 50 ohm NF 400 W ≤ 2.0 Vertical 2 dBi E-plane 75° H-plane 360° >27 dB The metal parts of the antenna, including the mounting kit and the inner conductors are DC grounded
RADIATION PATTERNS (Mid Band) 0
270
90 10 6 3 1 dB 180
H-plane
MECHANICAL DATA DIMENSIONS WEIGHT WIND SURFACE WIND LOAD (wind speed 150 km/h) MAX. WIND VELOCITY ICING PROTECTION RADOME COLOUR MOUNTING
DS 921.120.114/01
2690 x ø 169 mm 34.5 kg 0.45 m2 345 N 240 km/h Full radome Grey (std.), other on request On a flanged supporting pipe Flange 290 mm diameter
0
270
90 10 6 3 1 dB 180
E-plane
Specifications are subject to change without prior notice
13
ADDITIONAL INFORMATION Mounting:
The antenna can be attached on the top of a flanged supporting pipe.
Materials: Radiator: Radome: Base: All screws and nuts:
Aluminium, brass. Fiberglass, colour: grey. Hot dip galvanized steel. Stainless steel.
Two eyebolts for an easy lifting of the antenna
PLEASE NOTE: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufactures must be obeyed. DS 921.120.114/01
Specifications are subject to change without prior notice
14
TBT 02-360/U3
GROUND TO AIR COMMUNICATION OMNIDIRECTIONAL ANTENNA
FEATURES vertical polarization broadband 225 ÷ 400 MHz 2 dBi gain omnidirectional multi-element antenna consisting of three indipendently fed UHF dipoles
ELECTRICAL DATA TYPE FREQUENCY RANGE IMPEDANCE CONNECTOR MAX POWER VSWR POLARIZATION GAIN HALF POWER BEAMWIDTH DECOUPLING (between adjacent dipoles) LIGHTNING PROTECTION
TBT 02-360/U3 225 ÷ 400 MHz 50 ohm NF 400 W ≤ 2.0 Vertical 2 dBi E-plane 75° H-plane 360° >27 dB The metal parts of the antenna, including the mounting kit and the inner conductors are DC grounded
RADIATION PATTERNS (Mid Band) 0
270
90 10 6 3 1 dB 180
H-plane
MECHANICAL DATA DIMENSIONS WEIGHT WIND SURFACE WIND LOAD (wind speed 150 km/h) MAX. WIND VELOCITY ICING PROTECTION RADOME COLOUR MOUNTING
DS 921.120.119/01
3730 x ø 169 mm 39 kg 0.63 m2 475 N 240 km/h Full radome Grey (std.), other on request On a flanged supporting pipe Flange 290 mm diameter
0
270
90 10 6 3 1 dB 180
E-plane
Specifications are subject to change without prior notice
15
ADDITIONAL INFORMATION Mounting:
The antenna can be attached on the top of a flanged supporting pipe.
Materials: Radiator: Radome: Base: All screws and nuts:
Aluminium, brass. Fiberglass, colour: grey. Hot dip galvanized steel. Stainless steel.
Two eyebolts for an easy lifting of the antenna
PLEASE NOTE: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufactures must be obeyed. DS 921.120.119/01
Specifications are subject to change without prior notice
16
TBT 02-360/U4
GROUND TO AIR COMMUNICATION OMNIDIRECTIONAL ANTENNA
FEATURES vertical polarization broadband 225 ÷ 400 MHz 2 dBi gain omnidirectional multi-element antenna consisting of four indipendently fed UHF dipoles
ELECTRICAL DATA TYPE FREQUENCY RANGE IMPEDANCE CONNECTOR MAX POWER VSWR POLARIZATION GAIN HALF POWER BEAMWIDTH DECOUPLING (between adjacent dipoles) LIGHTNING PROTECTION
TBT 02-360/U4 225 ÷ 400 MHz 50 ohm NF 400 W ≤ 2.0 Vertical 2 dBi E-plane 75° H-plane 360° >27 dB The metal parts of the antenna, including the mounting kit and the inner conductors are DC grounded
RADIATION PATTERNS (Mid Band) 0
270
90 10 6 3 1 dB 180
H-plane
MECHANICAL DATA DIMENSIONS WEIGHT WIND SURFACE WIND LOAD (wind speed 150 km/h) MAX. WIND VELOCITY ICING PROTECTION RADOME COLOUR MOUNTING
DS 921.120.121/01
4770 x ø 169 mm 44 kg 0.81 m2 610 N 240 km/h Full radome Grey (std.), other on request On a flanged supporting pipe Flange 290 mm diameter
0
270
90 10 6 3 1 dB 180
E-plane
Specifications are subject to change without prior notice
17
ADDITIONAL INFORMATION Mounting:
The antenna can be attached on the top of a flanged supporting pipe.
Materials: Radiator: Radome: Base: All screws and nuts:
Aluminium, brass. Fiberglass, colour: grey. Hot dip galvanized steel. Stainless steel.
Two eyebolts for an easy lifting of the antenna
PLEASE NOTE: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufactures must be obeyed. DS 921.120.121/01
Specifications are subject to change without prior notice
18
TBT 02-360/U5
GROUND TO AIR COMMUNICATION OMNIDIRECTIONAL ANTENNA
FEATURES vertical polarization broadband 225 ÷ 400 MHz 2 dBi gain omnidirectional multi-element antenna consisting of five indipendently fed UHF dipoles
ELECTRICAL DATA TYPE FREQUENCY RANGE IMPEDANCE CONNECTOR MAX POWER VSWR POLARIZATION GAIN HALF POWER BEAMWIDTH DECOUPLING (between adjacent dipoles) LIGHTNING PROTECTION
TBT 02-360/U5 225 ÷ 400 MHz 50 ohm NF 400 W ≤ 2.0 Vertical 2 dBi E-plane 75° H-plane 360° >27 dB The metal parts of the antenna, including the mounting kit and the inner conductors are DC grounded
RADIATION PATTERNS (Mid Band) 0
270
90 10 6 3 1 dB 180
H-plane
MECHANICAL DATA DIMENSIONS WEIGHT WIND SURFACE WIND LOAD (wind speed 150 km/h) MAX. WIND VELOCITY ICING PROTECTION RADOME COLOUR MOUNTING
5810 x ø 169 mm 48.5 kg 0.98 m2 740 N 240 km/h Full radome Grey (std.), other on request On a flanged supporting pipe Flange 290 mm diameter
0
270
90 10 6 3 1 dB 180
E-plane
07.06.2011
Specifications are subject to change without prior notice
19
ADDITIONAL INFORMATION Mounting:
The antenna can be attached on the top of a flanged supporting pipe.
Materials: Radiator: Radome: Base: All screws and nuts:
Aluminium, brass. Fiberglass, colour: grey. Hot dip galvanized steel. Stainless steel.
Two eyebolts for an easy lifting of the antenna
PLEASE NOTE: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufactures must be obeyed. 07.06.2011
Specifications are subject to change without prior notice
20
TBT 02-360/U6
GROUND TO AIR COMMUNICATION OMNIDIRECTIONAL ANTENNA
FEATURES vertical polarization broadband 225 ÷ 400 MHz 2 dBi gain omnidirectional multi-element antenna consisting of six indipendently fed UHF dipoles
ELECTRICAL DATA TYPE FREQUENCY RANGE IMPEDANCE CONNECTOR MAX POWER VSWR POLARIZATION GAIN HALF POWER BEAMWIDTH DECOUPLING (between adjacent dipoles) LIGHTNING PROTECTION
TBT 02-360/U6 225 ÷ 400 MHz 50 ohm NF 400 W ≤ 2.0 Vertical 2 dBi E-plane 75° H-plane 360° >27 dB The metal parts of the antenna, including the mounting kit and the inner conductors are DC grounded
RADIATION PATTERNS (Mid Band) 0
270
90 10 6 3 1 dB 180
H-plane
MECHANICAL DATA DIMENSIONS WEIGHT WIND SURFACE WIND LOAD (wind speed 150 km/h) MAX. WIND VELOCITY ICING PROTECTION RADOME COLOUR MOUNTING
DS 921.120.122/01
6850 x ø 169 mm 53.5 kg 1.16 m2 875 N 240 km/h Full radome Grey (std.), other on request On a flanged supporting pipe Flange 290 mm diameter
0
270
90 10 6 3 1 dB 180
E-plane
Specifications are subject to change without prior notice
21
ADDITIONAL INFORMATION Mounting:
The antenna can be attached on the top of a flanged supporting pipe.
Materials: Radiator: Radome: Base: All screws and nuts:
Aluminium, brass. Fiberglass, colour: grey. Hot dip galvanized steel. Stainless steel.
Two eyebolts for an easy lifting of the antenna
PLEASE NOTE: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufactures must be obeyed. DS 921.120.122/01
Specifications are subject to change without prior notice
22
Multi dipole VHF omnidirectional antenna Vertical Polarization
TBT 02-360/V2
25
TBT 02-360/V3
27
Multi dipole VHF omnidirectional antenna Vertical Polarization TYPE NO.
TYPE
# INPUTS
HEIGHT
ANT/TBT 02-360/V2
VPol Omni
108-156 MHz
360°
2 dBi
2xNf
4785 mm
ANT/TBT 02-360/V3
VPol Omni
108-156 MHz
360°
2 dBi
3xNf
7025 mm
23
TBT 02-360/V2
GROUND TO AIR COMMUNICATION OMNIDIRECTIONAL ANTENNA
FEATURES vertical polarization broadband 108 ÷ 156 MHz 2 dBi gain omnidirectional multi-element antenna consisting of two indipendently fed VHF dipoles
ELECTRICAL DATA TYPE FREQUENCY RANGE IMPEDANCE CONNECTOR MAX POWER VSWR POLARIZATION GAIN HALF POWER BEAMWIDTH DECOUPLING LIGHTNING PROTECTION
TBT 02-360/V2 108 ÷ 156 MHz 50 ohm NF 500 W ≤ 2.0 Vertical 2 dBi E-plane 75° H-plane 360° >23 dB (typical >25 dB) The metal parts of the antenna, including the mounting kit and the inner conductors are DC grounded
RADIATION PATTERNS (Mid Band) 0
270
90 10 6 3 1 dB 180
H-plane
MECHANICAL DATA DIMENSIONS WEIGHT WIND SURFACE WIND LOAD (wind speed 150 km/h) MAX. WIND VELOCITY ICING PROTECTION RADOME COLOUR MOUNTING
DS 921.120.113/01
4785 x ø 169 mm 45.5 kg 0.81 m2 610 N 240 km/h Full radome Grey (std.), other on request On a flanged supporting pipe Flange 290 mm diameter
0
270
90 10 6 3 1 dB 180
E-plane
Specifications are subject to change without prior notice
25
ADDITIONAL INFORMATION Mounting:
The antenna can be attached on the top of a flanged supporting pipe.
Materials: Radiator: Radome: Base: All screws and nuts:
Aluminium, brass. Fiberglass, colour: grey. Hot dip galvanized steel. Stainless steel.
Two eyebolts for an easy lifting of the antenna
PLEASE NOTE: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufactures must be obeyed. DS 921.120.113/01
Specifications are subject to change without prior notice
26
TBT 02-360/V3
GROUND TO AIR COMMUNICATION OMNIDIRECTIONAL ANTENNA
FEATURES vertical polarization broadband 108 ÷ 156 MHz 2 dBi gain omnidirectional multi-element antenna consisting of three indipendently fed VHF dipoles
ELECTRICAL DATA TYPE FREQUENCY RANGE IMPEDANCE CONNECTOR MAX POWER VSWR POLARIZATION GAIN HALF POWER BEAMWIDTH DECOUPLING LIGHTNING PROTECTION
TBT 02-360/V3 108 ÷ 156 MHz 50 ohm NF 500 W ≤ 2.0 Vertical 2 dBi E-plane 75° H-plane 360° >23 dB (typical >25 dB) The metal parts of the antenna, including the mounting kit and the inner conductors are DC grounded
RADIATION PATTERNS (Mid Band) 0
270
90 10 6 3 1 dB 180
H-plane
MECHANICAL DATA DIMENSIONS WEIGHT WIND SURFACE WIND LOAD (wind speed 150 km/h) MAX. WIND VELOCITY ICING PROTECTION RADOME COLOUR MOUNTING
DS 921.120.120/01
7025 x ø 169 mm 57.5 kg 1.19 m2 895 N 240 km/h Full radome Grey (std.), other on request On a flanged supporting pipe Flange 290 mm diameter
0
270
90 10 6 3 1 dB 180
E-plane
Specifications are subject to change without prior notice
27
ADDITIONAL INFORMATION Mounting:
The antenna can be attached on the top of a flanged supporting pipe.
Materials: Radiator: Radome: Base: All screws and nuts:
Aluminium, brass. Fiberglass, colour: grey. Hot dip galvanized steel. Stainless steel.
Two eyebolts for an easy lifting of the antenna
PLEASE NOTE: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufactures must be obeyed. DS 921.120.120/01
Specifications are subject to change without prior notice
28
Multi dipole VHF/UHF omnidirectional antenna Vertical Polarization
TBT 02-360/UV
31
TBT 02-360/UVU
33
TBT 02-360/VUV
35
Multi dipole VHF/UHF omnidirectional antenna Vertical Polarization TYPE NO. ANT/TBT 02-360/UV
ANT/TBT 02-360/UVU
ANT/TBT 02-360/VUV
TYPE
# INPUTS
HEIGHT
VPol Omni
225-400 / 108-156 MHz
360°
2 dBi
2xNf
3650 mm
VPol Omni
225-400 / 108-156 / 225-400 MHz
360°
2 dBi
3xNf
4785 mm
VPol Omni
108-156 / 225-400 / 108-156 MHz
360°
2 dBi
3xNf
7025 mm
29
TBT 02-360/UV
GROUND TO AIR COMMUNICATION OMNIDIRECTIONAL ANTENNA
FEATURES vertical polarization broadband 108 ÷ 156 and 225 ÷ 400 MHz 2 dBi gain omnidirectional multi-element antenna consisting of one VHF and one UHF dipole (indipendently fed)
ELECTRICAL DATA TYPE FREQUENCY RANGE IMPEDANCE CONNECTOR MAX POWER VSWR POLARIZATION GAIN HALF POWER BEAMWIDTH DECOUPLING LIGHTNING PROTECTION
TBT 02-360/UV VHF: 108 ÷ 156 MHz UHF: 225 ÷ 400 MHz 50 ohm NF 500 W 400 W ≤ 2.0 Vertical 2 dBi E-plane 75° H-plane 360° at UHF >23 dB (typical >25 dB) at VHF >23 dB (typical >25 dB) The metal parts of the antenna, including the mounting kit and the inner conductors are DC grounded
RADIATION PATTERNS (Mid Band) 0
270
90 10 6 3 1 dB 180
H-plane
MECHANICAL DATA DIMENSIONS WEIGHT WIND SURFACE WIND LOAD (wind speed 150 km/h) MAX. WIND VELOCITY ICING PROTECTION RADOME COLOUR MOUNTING
DS 921.120.116/01
3650 x ø 169 mm 38.5 kg 0.62 m2 465 N 240 km/h Full radome Grey (std.), other on request On a flanged supporting pipe Flange 290 mm diameter
0
270
90 10 6 3 1 dB 180
E-plane
Specifications are subject to change without prior notice
31
ADDITIONAL INFORMATION Mounting:
The antenna can be attached on the top of a flanged supporting pipe.
Materials: Radiator: Radome: Base: All screws and nuts:
Aluminium, brass. Fiberglass, colour: grey. Hot dip galvanized steel. Stainless steel.
Two eyebolts for an easy lifting of the antenna
PLEASE NOTE: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufactures must be obeyed. DS 921.120.116/01
Specifications are subject to change without prior notice
32
TBT 02-360/UVU
GROUND TO AIR COMMUNICATION OMNIDIRECTIONAL ANTENNA
FEATURES vertical polarization broadband 108 ÷ 156 and 225 ÷ 400 MHz 2 dBi gain omnidirectional multi-element antenna consisting of one VHF and two UHF dipoles (indipendently fed)
ELECTRICAL DATA TYPE FREQUENCY RANGE IMPEDANCE CONNECTOR MAX POWER VSWR POLARIZATION GAIN HALF POWER BEAMWIDTH DECOUPLING
LIGHTNING PROTECTION
TBT 02-360/UVU VHF: 108 ÷ 156 MHz UHF: 225 ÷ 400 MHz 50 ohm NF 500 W 400 W ≤ 2.0 Vertical 2 dBi E-plane 75° H-plane 360° UHF - UHF >25 dB UHF - VHF at UHF >24 dB (typical >25 dB) UHF - VHF at VHF >22 dB (typical >25 dB) The metal parts of the antenna, including the mounting kit and the inner conductors are DC grounded
RADIATION PATTERNS (Mid Band) 0
270
90 10 6 3 1 dB 180
H-plane
MECHANICAL DATA DIMENSIONS WEIGHT WIND SURFACE WIND LOAD (wind speed 150 km/h) MAX. WIND VELOCITY ICING PROTECTION RADOME COLOUR MOUNTING
DS 921.120.115/01
4690 x ø 169 mm 43.5 kg 0.79 m2 600 N 240 km/h Full radome Grey (std.), other on request On a flanged supporting pipe Flange 290 mm diameter
0
270
90 10 6 3 1 dB 180
E-plane
Specifications are subject to change without prior notice
33
ADDITIONAL INFORMATION Mounting:
The antenna can be attached on the top of a flanged supporting pipe.
Materials: Radiator: Radome: Base: All screws and nuts:
Aluminium, brass. Fiberglass, colour: grey. Hot dip galvanized steel. Stainless steel.
Two eyebolts for an easy lifting of the antenna
PLEASE NOTE: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufactures must be obeyed. DS 921.120.115/01
Specifications are subject to change without prior notice
34
TBT 02-360/VUV
GROUND TO AIR COMMUNICATION OMNIDIRECTIONAL ANTENNA
FEATURES vertical polarization broadband 108 ÷ 156 and 225 ÷ 400 MHz 2 dBi gain omnidirectional multi-element antenna consisting of one UHF and two VHF dipoles (indipendently fed)
ELECTRICAL DATA TYPE FREQUENCY RANGE IMPEDANCE CONNECTOR MAX POWER VSWR POLARIZATION GAIN HALF POWER BEAMWIDTH DECOUPLING
LIGHTNING PROTECTION
TBT 02-360/VUV VHF: 108 ÷ 156 MHz UHF: 225 ÷ 400 MHz 50 ohm NF 500 W 400 W ≤ 2.0 Vertical 2 dBi E-plane 75° H-plane 360° VHF - VHF >22 dB (typical >25 dB) VHF - UHF at VHF >25 dB VHF - UHF at UHF >22 dB (typical >25 dB) The metal parts of the antenna, including the mounting kit and the inner conductors are DC grounded
RADIATION PATTERNS (Mid Band) 0
270
90 10 6 3 1 dB 180
H-plane
MECHANICAL DATA DIMENSIONS (mm) WEIGHT (kg) WIND SURFACE (m2) WIND LOAD (wind speed 150 km/h) (N) MAX. WIND VELOCITY ICING PROTECTION RADOME COLOUR MOUNTING
DS 921.120.125/01
6300 x ø 169 mm 52.5 1.06 805 240 km/h Full radome Grey (std.), other on request On a flanged supporting pipe Flange 290 mm diameter
0
270
90 10 6 3 1 dB 180
E-plane
Specifications are subject to change without prior notice
35
ADDITIONAL INFORMATION Mounting:
The antenna can be attached on the top of a flanged supporting pipe.
Materials: Radiator: Radome: Base: All screws and nuts:
Aluminium, brass. Fiberglass, colour: grey. Hot dip galvanized steel. Stainless steel.
Two eyebolts for an easy lifting of the antenna
PLEASE NOTE: As a result of more stringent legal regulations and judgements regarding product liability, we are obliged to point out certain risks that may arise when products are used under extraordinary operating conditions. The mechanical design is based on the environmental conditions as stipulated in ETS 300 019-1-4, which include the static mechanical load imposed on an antenna by wind at maximum velocity. Extraordinary operating conditions, such as heavy icing or exceptional dynamic stress (e.g. strain caused by oscillating support structures), may result in the breakage of an antenna or even cause it to fall to the ground. These facts must be considered during the site planning process. The installation team must be properly qualified and also be familiar with the relevant national safety regulations. The details given in our data sheets have to be followed carefully when installing the antennas and accessories. The limits for the coupling torque of RF-connectors, recommended by the connector manufactures must be obeyed. DS 921.120.125/01
Specifications are subject to change without prior notice
36
Anti-Icing System
37
ANTI-ICING SYSTEM SIRA has developed an anti-icing system to be connected to the base flange of the multi coaxial dipole VHF/UHF antennas. This anti-icing system allows the control of the hot air flow inside the antenna radome. MAIN FEATURES OF THE SIRA SOLUTION: Redundancy of system’s components Reduction of energy consumption The ANTI-ICING system modulates heating power in accordance to the external environmental conditions. The system is designed only using passive components inside the antenna (no maintenance). Distribution of the heating over the entire length of the antenna. The activation of the remote control can be made through RS232 or TCP-IP.
CAlling Air-Intake
Hot air
Anti-Icing kit
ON
HEATING RADOME
38
ANTI-ICING SYSTEM Schematic block - Master and Slave Multi coaxial dipole VHF/UHF antennas
1
2
3
N
RESISTANCE
FAN
SLAVE > PLUG AND PLAY
Master
POWER SUPPLY REMOTE CONTROL
The system is based on a programmable Logic controller (PLC) that receives data from a professional weather station on temperature and frost conditions.
Professional Weather Station with calibration certificate.
39
ANTI- ICING SYSTEM Trial Terminillo – site mountain 2000 m Multi coaxial dipole antennas UVU Height = 4.7 mt
Professional Weather Station
Anti-Icing system Remote control
40
