Transcript
SINKS GENERAL SPECIFICATIONS ROUNDED FRONT EDGE AND ROUNDED USPSTAND ARE SIMILAR TO THOSE OF THE STAINLESS STEEL TABLES AND UNITS
- Stainless steel construction - Height 900 mm (height 850 mm on request). - Upstand height 100 mm. - Grooved draining boards, anti-drip edges. - Soundproofed basins and draining boards - 3 covered sides. - Stainless steel tube underframe Ø 45 mm with adjustable feet, 80 mm indent at rear. - Delivered with overflow tube and polypropylene siphon, and choice of with or without mixer tap 15 x 21 mm.
LENGTH 1600 MM FOR SINKS WITH BASIN 500 X 500 MM
SINKS LARGE BASINS - Same specificiations, except for: * construction which is welded instead of being assembled using screws. * Delivered complete with overflow tube, filter grid and brass trap, on a pallet instead of delivery as flat pack. GROOVED DRAINING BOARDS
Basin Basin Basin Basin Basin 500 x 400 x 250 500 x 500 x 300 600 x 500 x 320 760 x 510 x 380 800 x 600 x 450 (mm) (mm) (mm) (mm) (mm)
References for sinks with tap 1 basin
-
816 670
816 680
816 860
816 870
1 basin + 1 draining board to right
816 661
816 671
816 681
816 863
816 873
1 basin + 1 draining board to left
816 662
816 672
816 682
816 864
816 874
2 basins 2 basins + 1 draining board right (length 1600 mm) 2 basins + 1 draining board (length 1600 mm) 2 basins + 1 draining board right (length 1,800 mm) 2 basins + 1 draining board (length 1,800 mm)
816 663
816 673
816 683
816 865
816 875
-
816 677
-
-
-
-
816 678
-
-
-
816 664
816 674
816 684
816 868
816 878
816 665
816 675
816 685
816 869
816 879
to to left to to left
Basins without tap: prefix 806 instead of 816. This document is not binding. The specifications given are subject to change with a view to improvement.
SINKS SINKS WITH SHELF - Lower shelf in stainless steel - Fixed with screws through parts moulded onto the legs
WALL SINKS Tel: + 33 (0)3 85 27 42 65 Fax: + 33 (0)3 85 27 42 60
- With basins 500 x 500 or 600 x 500 mm. - Fixture by 2 or 3 wall supports under upstand, with 2 jacks for horizontal adjustment.
E-mail:
[email protected]
SINK FOR INTEGRATED DISHWASHERS Web site: www.tournus.com
- With basins 500 x 500 mm. - Cladding on bowl only, and offset stand, making room to build in a dishwasher.
MADE TO MEASURE SINKS - With basins 500 x 500 x 300, 600 x 500 x 320,
ROUNDED FRONT EDGE AND 680 x 510 x 400 (GN), 760 x 510 x 380, 800 x 600 x 450 mm. ROUNDED UPSTAND, GROOVED - Same conception as the standard sink units, DRAINING BOARDS ON ALL MODELS, length made-to-measure up to 2500 mm INCLUDING MADE-TO-MEASURE - Specify when ordering position of basins and drilling diameter
for the tap ( 1 hole - 2 holes) or no drilling (wall tap).
ACCESSORIES 230 300
806 730
806 725
- Mixer tap 15 x 21, 30 l/min, ref. 230 300 - Mixer tap, 1/4 turn Chavonnet 5640 T3, flow rate 30 l/min, ref. 806 730 - Mixer tap, 1/4 turn Chavonnet 5610, flow rate 97 l/min, ref. 806 725 - Mixer shower, ref. 230 241 - Mixer shower + goose neck, ref 230 245
EXTRAS RC Mâcon B 383 567 104 Code APE 295 E SAS Capital 16 355 625 €
lateral upstand
- Lateral upstand - Adaptation for knee-operated - Wheeled units.
This document is not binding. The specifications given are subject to change with a view to improvement.
