Transcript
Revision level 30.08.16 Tabletop reinforcement bar installation (for the option with two legs)
Assembly instruction for metal workbenches WS series Screen WS
Tabletop reinforcement bar
Tabletop WTH
Screen WS
View E (installation of the reinforcement bar into the leg’s grooves) F
E
Tabletop WTH
View F (reinforcement bar mounted to the leg)
Tabletop reinforcement bar
Leg WF-2
Pedestal WS-6
Pedestal WS-1
Leg WF-2
Leg WF-2 Leg WF-2
All modifications of the metal workbenches WS you can find on the website www.promet-safe.com WSH shelf installation View A Pedestal WS-6 (shelf mounted to pedestal WS)
View B (shelf mounted to leg WF-2)
Nut M6 Washer 6
Bolt M6
1. Install the legs at the distance from each other approximately equal to the tabletop reinforcement bar’s length. 2. Install the tabletop reinforcement bar into the leg’s grooves, as demonstrated on the picture (view E) 3. Mount the tabletop reinforcement bar to the leg WF-2 with bolts, washers and nuts (view F)
3 WSH bar assembly (for the option with two legs) Central bar
B А
1
WSH shelf
Bolt M5
Leg WF-2
Bolt M5 Washer 5 Nut M5
1. Install the pedestal WS and the leg WF-2 so that their front planes are on the same level. 2. Install a shelf by mounting it to the pedestal with bolts, and to the leg WF-2 with bolts, washers and nuts. C
WSH back panel installation D
View C (back panel mounted to pedestal WS)
Retractable bar G
View G (WSH bar mounted to the leg WF-2)
View D (back panel mounted to leg WF-2)
Nut M6 Washer 6
1. Install a central bar into the retractable one (for the tabletop of 160cm – to match the first three holes, for the tabletop of 200cm – to match the first holes) 2. Combine the central and the retractable bars with bolts, washers and nuts (View G).
Bolt M5 WSH back panel
2
Bolt M5
Washer 5
Nut M5
1. Install a back panel by mounting it with bolts to the pedestal WS, and with bolts, washers and nuts to the leg WF-2.
Page 1/7
4
Bolt M6
Page 2/7
Tabletop W/WTS/WTH
WSH bar installation (for the option with two legs) WSH bar
View H (WSH bar mounted to the leg WF-2)
Mounting of corner bars and reinforcement bar to tabletop W/WTS/WTH (for the option with two legs) Corner bar
Tabletop W/WTS/WTH
I H
Screw
Nut M6 Washer 6
Leg WF-2
5
1. Install the WSH bar, mounting it with bolts, washers and nuts to the leg WF-2. Bolt M6
Leg WF-2 Tabletop reinforcement bar
View I (corner bar mounted to the leg WF-2 and to the tabletop)
Mounting of pressed nuts to tabletop 1. Using the hex wrench 8 mm screw the pressed nuts M8x12.15x13 into prepared holes in the tabletop 1a. Screw 6 pressed nuts under the leg
1b. Screw 4 pressed legs under the pedestal
1. Mount a corner bar to the leg WF-2 with bolts, washers and nuts. 2. Mount the corner bar to the tabletop with screws. 3. Mount the tabletop reinforcement bar to the tabletop with screws.
Screw
Pressed nut M8x12,5x13
6
8
Bolt M6
Nut M6 Washer 6
Installation of Tabletop W/WTS/WTH
Table pad Installation to tabletop W/WTS/WTH
Tabletop W/WTS/WTH
Screw
Bolt M8x16
View J (table pad WTS/WTH mounted to the tabletop W)
Table pad WTS/WTH
1a. Remove 2-3 top drawers (see operation 6 – for the pedestal WS-6) 1. Put the tabletop on the top. Straighten it so that the holes in the pedestal and in the leg match with the holes in the tabletop. 2. Mount the pedestal and the leg to the tabletop with the bolts M8x16. The pedestal is mounted with 4 bolts, and the leg – with 6 bolts.
J Table pad WTS/WTH
7
9 Page 3/7
1. On the top of the tabletop install the table pad WTS/WTH (see view J) 2. Mount the table pad with screws
Tabletop W/WTS/WTH
Page 4/7
Installation of WS wheel set on pedestal WS-1 and 6 Washer 8 enlarged (purchased as an option, separately)
WS Screen Installation on workbench WS Screen
Only for the models produced after 01.02.16
Nut М5 Washer 5 Bolt М5х12 Right stop
Left stop Screw
1. Unscrew the screws, mounting the tabletop’s pad. 2. Screw left and right stops to the tabletop with screws. 3. With bolts, washers and nuts mount the screen to the stops. 4. With screws mount the screen to the tabletop.
Bolt М8
Turning wheel Turning wheel with brake
Installation of WS wheel set 1. Dismantle a socle from the pedestal, unscrew 4 bolts. 2. Install 4 wheels with bolts and washers. Placement of wheels with brake, choose by place
10 Drawer removal from tabletop WS-6
13
Pedestal WS-1 with installed WS wheel set
1
Lock
2
Rail guide 1. Pull out the two upper drawers until they stop. 2. Turn the plastic locks in the rail guides back 3. Remove the drawers from the rail guides
11
Installation of WS handle on leg WF-2
Installation of WS handle on pedestal WS-1/6
Only for the models produced after 01.02.16 WS handle
Bolt М8х40 DIN 912
WS handle Upper crossbar of the leg WF-2
Possible options of installation of WS handle on pedestal WS-1/6
12
1. Install the handle WS on the front or on the side of the pedestal WS-1/6 with the bolts M8x40
12.1
Washer 8 Nut М8
1. Install the handle WS on the leg WF-2 with the bolts M8x40, washers and nuts.
Page 5/7
page 6/7
NOTES TO THE INSTRUCTION 1. Assembly sequence is specified by the ordinal number in the left upper corner of each figure of the assembly operation. 2. Type and quantity of the mounted products (if they are needed) for the assembly operation are specified near the ordinal number of the assembly operation. 3. The note on the figure field specifies a name of the installed element. Recommendation for exploitation of pedestals WS. 1. It is recommended to evenly spread weight over the drawer’s bottom for the optimal load of rail guides. 2. It is recommended to evenly spread weight over the shelf for the optimal load of shelf-holders. Attention: 1. When using the pedestals (drawers) WS-0/1/6 pull out STRICTLY one by one, because pulling out of two or more loaded drawers simultaneously can lead to their dumping. 2. It is not allowed to put the drawers WS-0 into a column and hang them to the workbench’s tabletop, because under the pressure the drawer can come off the tabletop.
Notes 1. Constructive changes, not noted in this instruction, are possible. 2. The leg WF-2 is adjustable in height every 50 mm. 3. Also there is a possibility of mounting the pedestal and the leg to the tabletop with screws. Holes for screws on the top of the pedestal and in the leg are provided.
Page 7/7
