Transcript
Rev 0 – June 2014
Key Digital®, led by digital video pioneer Mike Tsinberg, develops and manufactures high quality, cutting-edge technology solutions for virtually all applications where high quality video imaging is important. Key Digital® is at the forefront of the video industry for Home Theater
Phantom Series™ HDMI Switchers with Audio De-Embedder, Coaxial Audio, Optical Digital Audio & Analog L/R, support Ultra HD/4K
Retailers, Custom Installers, System Integrators, Broadcasters, Manufacturers, and Consumers.
Operating Instructions
KD-HD2x1ProK
KD-HD4x1ProK
The Experts in Digital Video Technology and Solutions™
Key Digital® Systems :: 521 East 3rd Street :: Mount Vernon, NY 10553 Phone : 914.667.9700
Fax : 914.668.8666
Phantoms_HDProK_Switchers_Manual.indd 2-3
Web : www.keydigital.com
6/5/14 10:48 AM
4
1
Table of Contents
Introduction
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Key Digital® Phantom Series™ HDMI switchers are designed and engineered to offer the
Quick Setup Guide . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
best quality, performance, and reliability while providing a cost-effective HDMI/DVI switching solution. Phantom Series™ HDMI switchers are a transparent solution for all digital video/
Installation and Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
audio switching applications and support all HD and SD video standards, including Ultra
DVI Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
HD/4K, 3D and 1080p/60. KD-HD2x1ProK / KD-HD4x1ProK switchers feature iAS™
IR Remote Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
(Intelligent Auto Sense) signal detection and automatic switching, pushbutton control, IR,
Serial IR & IR Emitter Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 EDID Control Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 External Audio Outputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 RS-232 Commands and Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
RS-232, status-monitoring LEDs, and support for HDMI CEC. The Phantom Series™ switchers support multiple unit expandability, and are individually addressable. Key Features ›› Digital Switching: 2/4 HDMI Sources to 1 HDMI Display ›› Resolution Support: Supports all SD, HD, and VESA (VGA, SVGA, XGA, WXGA, SXGA, UXGA)
Using iAS Intelligent Auto Sense . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 ™
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Important Product Warnings & Safety Instructions: . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 How to Contact Key Digital® . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Warranty Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
›› ›› ›› ›› ›› ›› ›› ›› ›› ›› ›› ›› ››
resolutions up to Ultra HD/4K, 3D and 1080p/60 (60Hz & 50Hz) »» SD & HD: 480i, 480p, 720p, 1080i, 1080p and Ultra HD/4K »» VESA: From 640x480p up to 1920x1200p 3D Ready: Capability to pass 3D stereoscopic signal formats Ultra HD/4K: 4K/2K video resolution support for 4K-capable televisions and commercial applications such as Digital Movie Theaters, CAD, Post Production Audio De-Embedder: Can de-embed audio from the HDMI input and send it to external digital or analog audio outputs Lossless Compressed Digital Audio: Dolby® TrueHD, Dolby® Digital Plus and DTS-HD Master Audio™ EDID Control: 16 internal library settings or auto EDID detection from display Licensing: Fully licensed and compatible with all HDMI and HDCP technologies I2C Communication: EDID and HDCP transparency from Display to Source Control: Front panel push buttons and LEDs, Optical IR Deep Color Support: Up to 12 bits/color Signal rates: up to 3.4 Gb per second CEC: Fully Supported Firmware upgradable Rack mountable
Accessories
Always follow the instructions provided in this Operating Manual.
›› ›› ›› ›› ››
External power supply: 5V 2A HDMI Lacing Clips Rack Ears Operating Instructions Warranty Card
© 2014 Key Digital, Inc. All rights reserved.
Phantoms_HDProK_Switchers_Manual.indd 4-1
6/5/14 10:48 AM
Serial IR
DVD
Plasma TV
RS-232
HDMI
Optical IR
Speakers
Subwoofer
Optical IR
2
3
Cable
Blu-Ray
EDID Control
HDMI
HDMI
Audio Rcvr. HDMI
KD-HD4x1ProK
Plasma HDMI
RS-232
Quick Setup Guide HDMI
Audio
TV
Installation and Operation
Optical IR
Speakers
›› Step 1: Find a safe and convenient locationOptical toIR mount or place your KD-HD ProK unit Cable ›› Step 2: Begin with the KD-HD ProK unit and all input/output devices turned off with power EDID Control
Step 3: Step 4: Satellite Step 5: Step 6: Step 7: Step 8:
HDMI
Satellite
Serial IR
DVD
›› ›› ›› ›› ›› ››
Audio
HDMI cables removed Audio Rcvr. Connect your HDMI or DVI-D source devices to the input ports of your KD-HD ProK unit Audio Connect your HDMI or DVI-D display to the output port of your KD-HD ProK unit HDMI Connect the desired IR or RS-232 control inputs to your KD-HD ProK unit Audio HDMI Be sure the Operation Mode Switch is set to the “Normal” position Connect power to the KD-HD ProK unit Power on input/output devices
Subwoofer Before permanently securing the unit for final installation, test for proper Speakers operation of the unit and cables in your system. It is recommended that you leave enough Blu-Ray ventilation space to provide sufficient airflow and cooling. HDMI
An optional HDMI cable clip (included) allows for a secure HDMI cable connection to be made to the rear of DVD and helps defeat intermittent or complete signal the unit KD-HD4x1ProK loss due to poor connection.
Optional HDMI Cable clip (included)
HDMI
Optical IR
Active Input / Output LED Indicators Cable
Serial IR RS-232
Optical IR
Your KD-HD ProK unit may be controlled via the pushbutton on the front of the unit. Select your desired input by depressing the “Input Select” button. The front LED indicators (1, 2, 3, 4) correspond to the selected input. HDMI
EDID Control
Blu-Ray HDMI
Satellite HDMI
DVD
KD-HD4x1ProK
HDMI
Serial IR RS-232
Audio Rcvr.
Optical IR
Plasma TV
Audio
Cable
HDMI
Optical IR
HDMI Audio
HDMI/DVI
Audio
DVI Applications
Audio
EDID Control
Audio
KD-HD HDMI can also be used with DVI-D sources and displays. For these *To connectProK DVI, use HDMI to DVISwitchers adapters applications, use DVI to HDMI adapters. Note that while HDMI supports both video and audio over an HDMI cable, DVI-D supports only video. Speakers
Satellite HDMI
Sub-Woofer
Speakers
Desktop PC DVI Video*
Audio Rcvr.
KD-HD4x1ProK
Plasma TV
Audio
Laptop
DVI Video*
Serial IR
Plasma TV
RS-232
HDMI
Optical IR
DVI Video* Optical IR
Desktop PC
EDID Control
Audio
Audio
Audio
HDMI/DVI
DVI Video*
Audio
*To connect DVI, use HDMI to DVI adapters
DVI
Speakers
Sub-Woofer
Speakers
Laptop
DVI Video*
*To connect DVI, use HDMI to DVI adapters
Note: N o signal conversion is done on the KD-HD2x1ProK; KD-HD4x1ProK. Desktop PC If input signal is HDMI output signal will be HDMI. If input signal is DVI output signal will be DVI. DVI Video*
KD-HD4x1ProK Laptop
DVI Video*
Serial IR
Plasma TV
RS-232 Optical IR
DVI Video*
Desktop PC Phantoms_HDProK_Switchers_Manual.indd 2-3
Optical IR
6/5/14 10:48 AM
Speakers
4
5
IR Remote Control
EDID Control Settings
The KD-HD ProK switcher features IR sensors on the front and rear of the unit for reception of the IR signals, and can be operated using the IR remote control provided with your unit.
At times, your HDMI sources and display may not synchronize properly. This is when EDID* control should be utilized. KD-HD ProK Switchers feature an internal library of EDID settings to ensure your HDMI source’s output is compatible with the display devices.
Power Input Select
Please reset the unit by either unplugging and plugging the HDMI connections, or via a power cycle for the new settings to take effect.
EDID Settings
Auto Input Select
Input Select Scroll Up
Input Select Scroll Down Numeric Keypad
Rotary EDID Control Switch
›› The default EDID is ‘00’--Copy EDID from HDMI output.
The 16 possible EDID settings range from ‘00’ to ‘F’. (‘00’ is the default).
R1, R2, R3
00
Copy EDID from HDMI Output
A
4Kx2K, 2CH AUDIO
Reserved for future use
01
1080i, 2Ch Audio
B
4Kx2K, DOLBY/DTS 5.1
02
1080i, Dolby/DTS 5.1
C
4Kx2K, HD AUDIO
03
1080i, HD Audio
D
1280x1024 DVI
04
1080p, 2Ch Audio
E
1920x1080 DVI
05
1080p, Dolby/DTS 5.1
F
1920x1200 DVI
06
1080p, HD Audio
07
3D, 2Ch Audio
08
3D, Dolby/DTS 5.1
09
3D, HD Audio
Serial IR & IR Emitter Control The “Serial IR” port requires the use of a Male 3.5mm Mono cable (not included) with the IR command signal being carried on the “Tip” of the input inserted into the KD-HD ProK unit. The location of the IR signal may vary by control system used. Please verify the location of the IR signal with your control system. Ground Signal
Addressing Mode Units may be addressed when used in a cascaded configuration. To address your Champion Series switch, press the following buttons on the Key Digital IR remote control: R3 » R1 » R2 » XX
When using the IR Emitter / IR Extender (sold separately), the IR Emitter must be mounted over the IR Sensor on the KD-HD ProK unit. It is recommended that the rear IR sensor of the KD-HD ProK unit be utilized for these applications. One end of the cable is connected to the IR Receiver / Master Controller / IR Extender / IR Connecting Block, while the other end is mounted over the IR Sensor of the KD-HD ProK unit.
The XX characters will be replaced with the two digit address you wish to assign to the unit. The default address is 00--Single unit mode.
HPD Control You may force Hot Plug Detection (HPD) to a source, or use Normal HPD mode (default). ›› To set the Normal HPD mode (default) press the following buttons on the Key Digital IR remote
control: R1 » R2 » R3 » 0 » 1 ›› So set Forced HPD on, press the following: R1 » R2 » R3 » 0 » 0
Resetting to Factory Default To reset your unit to factory default, press and hold the Input Select button on the front panel for 10 seconds. *EDID (Extended display identification data) is a data structure provided by a display to describe its capabilities to a source device.
Phantoms_HDProK_Switchers_Manual.indd 4-5
6/5/14 10:48 AM
6
7
Example of EDID Auto Select: If one of your system’s displays supports 1080p and the second display only supports up to 1080i (does not support 1080p), then the highest common EDID format supported is 1080i. By choosing the Auto Select EDID Setting, your KD-HD ProK unit will inform your source device to output 1080i in order to ensure all displays receive a supported signal.
External Audio Outputs
STA
Show Global System Status
Video Output Setup Commands: yy = [01-04] (A=All) SPO SIyy
Set Output to Video Input yy
SPO ON/OFF
Set Output ON/OFF
Audio Output Setup Commands: [E=Enable, D=Disable] SPO AA E/D
Enable/Disable External Analog Audio Output
Analog audio output via 3.5mm stereo phone jack ›› 2 channel analog audio output from the selected HDMI input source ›› Converts only 2 ch. PCM audio from the HDMI input to 2 channel analog audio output ›› Only supports 2 ch. PCM audio, not multi-channel PCM, Dolby, DTS, HD audio
SPO DA E/D
Enable/Disable External Digital Audio Output
System Address Setup Command: xx = [00-99], 00 = Single SPC Axx
Set System Address to xx
System Control Setup Commands: SPC AS x
Set Auto Sense Mode x = [ 0:OFF, 1=AUTO, 2=FORCED ON ]
SPC FB E/D
Enable/Disable Front Panel Buttons
Digital audio output via Coax/RCA
SPC FHPD ON/OFF
Set Forced HPD ON/OFF
›› Digital audio output from the selected HDMI input source ›› Uses SPDIF format ›› Supports 2 ch. PCM, Dolby, DTS; does not support multi-channel PCM or HD audio
SPC DF
Reset to Factory Defaults
Digital audio output via Optical ›› Digital optical audio output from the HDMI input ›› Uses SPDIF format ›› Supports 2 ch. PCM, Dolby, DTS; does not support multi-channel PCM or HD audio
RS-232 Commands and Protocol ›› KD-HD ProK units are compatible with all Control Systems, such as Compass Control®, AMX®,
Control4®, Crestron®, RTI®, Universal® ›› Connect your Control System’s Master Controller to the KD-HD ProK unit using the RS-232 port.
Follow all instructions provided with your control system. ›› RS-232 Protocol: »» Baud Rate = 57600 bits per second »» Data Bits = 8 / Stop Bits = 1 »» Parity = None »» Flow Control = None ›› All RS-232 commands must be in lower case letters ›› Command must be terminated with a carriage return
RS-232 Command
Description
Using iAS Intelligent Auto Sense™ Intelligent Auto Sense (iAS™) will automatically switch inputs when a Hot Plug Detect signal becomes active on an input. iAS™ can be enabled and disabled via IR or RS-232 control. Please note that many common HDMI sources, such as a cable or satellite boxes, will emit Hot Plug Detect signals when in stand-by mode and may prevent full functionality of iAS™. When the blue “Auto” button on the IR remote is pressed or the ‘SPC AS ON’ RS-232 command is sent, iAS will be activated on the KD-HD ProK unit. NOTE: iAS will be disabled when the input button on the front of the unit is pressed to switch inputs or if any of the input select/scroll buttons on the IR remote are pressed.
Specifications Technical: »» Input (Each): HDMI Connector, Type A, 19 Pin Female »» Output: HDMI Connector, Type A, 19 Pin Female »» Bandwidth: TMDS bandwidth 3.4 Gb/s »» Control: Front panel push buttons and LEDs; front/rear IR sensors; Wired IR - rear 3.5 mm
female mini-stereo connector; RS-232 - DB9 Female connector for Tx, Rx and ground
Azz
All Commands may have Prefix System Address zz=[01-99]
»» Deep Color Support: Digital video formats in Deep Color Mode up to 12 bits/color
H
Help
»» HDMI® and HDCP Licensing: Fully licensed and compatible with all HDMI
PF
Power Off
PN
Power ON
Phantoms_HDProK_Switchers_Manual.indd 6-7
and HDCP techologies »» Compliance with HDMI Standards: Supports all versions of HDMI and HDCP »» Link:Single Link - 4K/3D/1080p/60, 12 bit color depth, 1920x1200 max.
6/5/14 10:48 AM
8
9
»» EDID Control:16 Default EDID settings. EDID information is assigned to the inputs from the
internal EDID library or from a display’s internal EDID data »» Lossless Compressed Digital Audio: Supports Dolby® TrueHD, Dolby® Digital Plus and
DTS-HD Master Audio
™
»» DDC Signal (Data):Input DDC Signal - 5 Volts p-p (TTL)
Power Supply Use: You MUST use the Power Supply provided with your unit or you VOID the Key Digital® Warranty and risk damage to your unit and associated equipment.
»» HDMI Video/Audio Signal:Input Video Signal - 1.2 Volts p-p »» DDC Communication:EDID and HDCP Bi-directional Transparency from Display to Source »» Wired IR: modulated IR signal input, 0-5V TTL or -10to +10V. »» Power: 5 Volt DC @ 2 Amp, 100-240 VAC, 50-60 Hz
General:
Power Supply Use: You MUST use the Power Supply provided with your unit or you VOID the Key Digital® Warranty and risk damage to your unit and associated equipment.
»» Regulation: CE, RoHS, WEEE »» Enclosure: Black Metal »» Product Dimensions: 8.2” x 1.67” x 3.9” »» Shipping Dimensions: 11.6” x 6.9” x 4.9” »» Product Weight: 2 lbs »» Shipping Weight: 5 lbs
Important Product Warnings: 1. Connect all cables before providing power to the unit. 2. Test for proper operation before securing unit behind walls or in hard to access spaces. 3. If installing the unit into wall or mounting bracket into sheet-rock, provide proper screw support with bolts or sheet-rock anchors.
Safety Instructions:
How to Contact Key Digital® Technical Support For technical questions about using Key Digital® products, please contact us at: ›› Phone: 914-667-9700 ›› E-mail:
[email protected]
Repairs and Warranty Service Should your product require warranty service or repair, please obtain a Key Digital® Return Material Authorization (RMA) number by contacting us at: ›› Phone: 914-667-9700 ›› E-mail:
[email protected]
Feedback Please email any comments/questions about the manual to: ›› E-mail:
[email protected]
Please be sure to follow these instructions for safe operation of your unit. 1. Read and follow all instructions. 2. Heed all warnings. 3. Do not use this device near water. 4. Clean only with dry cloth. 5. Install in accordance with the manufacturer’s instructions.
Warranty Information All Key Digital® products are built to high manufacturing standards and should provide years of trouble-free operation. They are backed by a Key Digital Limited Lifetime Product Warranty Policy. » http://www.keydigital.com/warranty.htm
6. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 7. Only use attachments/accessories specified by the manufacturer. 8. Refer all servicing to qualified service personnel. Servicing is required when the device has been damaged in any way including: »» Damage to the power supply or power plug »» Exposure to rain or moisture
Phantoms_HDProK_Switchers_Manual.indd 8-9
6/5/14 10:48 AM
