Transcript
PHARE. The Mast Concept
.de
Video surveillance in open-air areas The efficient surveillance of open-air areas very often require the installation of video cameras and light sources attached to free-standing poles or masts. Frequently, for that purpose, the same type of masts is used for street or area lighting. Normally, these are round pipe sections with a buried base and different diameters over the overall length (multiple spigots). Usually, an inspection flap is integrated in the lower part of the pole, big enough to allow for the housing of electric lighting connections and circuit breaker elements. The cable conduits may run inside the pipe - cable outlets to the lighting sources consist of drilled holes and screw holds in the round pipe section or at the upper end of the mast. For today’s network-based video surveillance, however, this type of technology can be used to a limited extent only, because due to the length restrictions required for CAT cables additional electronic components are needed to transport image content via fiber optic cables. These electronic components require not only space but also power supply. Inside a mast, as we initially described, there would not usually be sufficient space to house all these additional components needed.
The PHARE concept, therefore, provides for: • • • •
mast – square steel profile – configurable up to a height of 6 meters foldable for pre-installation and fixing the electric connections all cables are concealed and unreachable within the profile connection box (lockable) either in the lower part (approx. 1 m over ground foundation) or, for security and anti-sabotage reasons, fixed at the top (to one of the upper mast segments) • (top) cable outlet pre-installed on the four sides • attachments for camera wall brackets with inside cable conduits, e.g. for WBOVA2 are prefabricated with core threads at the four sides • prefabricated core threads for the fixation of IR LED spots of the SEVEN-V-series, also on all four sides
Advantages • CAMERA and SPOTLIGHT components can be preinstalled at the top pole segment in the workshop • Raising of the mast can be done by one single person • Electric connections can be installed in place, with the mast being jacked-up, particularly if the ASK7 is to be fixed to one of the upper pole segments • For servicing it is easy to tilt the mast and access all components (cameras, light sources and switch box)
PHARE. Mast Length: 6m LightDec GmbH & Co. KG Stand 02/2014
Robert-Bosch-Str. 6 | 85053 Ingolstadt | www.lightdec.de |
[email protected] Tel.: 0049 / 841 / 97475 -29 | Fax.: 0049 / 841 / 97475 -43
PHARE. SHELTER .de
Technical data Mast base:
steel, hot-dip galvanized, 10 mm grounding clamp for earth strip or earth wire fixation with 4 x M20 adjustment with screw type 4 x M16 (pressure plate, galvanized, 3 mm) mast is foldable, screw type 2 x M16 heavy-duty dowel type M20 (4 are needed, or a crate of screws are to be ordered separately)
Basic mast:
3m m, 120 x 120 mm, wall thickness 3 mm, hot-dip galvanized, prepared with mast base cut-out for connection box ASK 7 at the pole bottom (or at the top, optional)
Mast top:
1m m, 120 x 120 mm, 3 mm wall thickness, hot-dip galvanized Master gauge for holes with M5 threads are prepared on all four sides for - wall bracket Lightdec SEVEN-V series and - wall bracket WBOVA2
Mast extension: 1 m m, 120 x 120 mm, 3 mm wall thickness, hot-dip galvanized Mast extension: 2 m m, 120 x 120 mm, 3 mm wall thickness, hot-dip galvanized Mast connection: screws
a set consisting of 2 connecting plates, 8 mm, hot-dip galvanized, and 8 x M10
Mast cap:
steel, hot-dip galvanized, 2 x M4 screws
Cover:
steel, hot-dip galvanized, 2 x M6 screws (up to 3 are required)
Special designs (length, cut-outs, master-gauge holes etc.) are made on request
Details Mast head
Cable entry
ASK with concealed
Lock
with master-gauge holes
at the ASK rear side
cable ducts
as accessory set
Errors and technical changes excepted
LightDec GmbH & Co. KG Stand 02/2014
Robert-Bosch-Str. 6 | 85053 Ingolstadt | www.lightdec.de |
[email protected] Tel.: 0049 / 841 / 97475 -29 | Fax.: 0049 / 841 / 97475 -43
ASK 7 Connection box
art. no.: 5826 .de
Compatible with the PHARE mast concept The ASK 7 connection box allows for all connecting cables to be connected in a discrete and vandal-resistant way. The installation can easily and safely be performed by one person only using the HANDFREE© mounting adapter. The ASK 7 offers all functionalities of a modern video-mast connection box.
ASK 7
Technical data • • • • • • • • • •
Weatherproof aluminum die-cast housing (IP65) Cable screws M25 for 2 x earth cables 230 Volt, 4 mm2 Cable screws M16 for 2 x cables 230 Volt, 2,5 mm2 Cable screws M25 for 2 x ethernet cables, video cable, etc. Cable screw M16 for 1 x fiber optic cable Mounting support with terminal screw connectors and universal mounting grid UMR © 230 Volt socket with RCD switch (FI safety switch) Temperature range -30°C - +50°C (Operation mode) Optional: - splice box with connector - fiber patch cable simplex - fiber patch cable duplex - quadruple switch/media converter/PoE => SWEEDER® 4 Up to 4 cameras or spotlights may be served (2 of which are mountable) - Power supply unit for PoE supply 60 Watt Up to 4 cameras (15 Watt) or 1 camera (15 Watt) and one PoE Seven-V spotlight - Power supply unit for PoE supply 240 Watt Up to 4 cameras (15 Watt) and 4 PoE Seven-V spotlights - Set of stainless-steel hinges - Set of stainless steel locks - Electronic lid surveillance - Mounting set for PHARE rectangular mast - Mounting set for round mast (third-party products) ASK7 with
ASK7 with
.. splice box .. 1 x SWEEDER® 4 .. power supply 60W .. FI safety switch .. 230VAC socket
.. splice box .. 2 x SWEEDER® 4 .. power supply 240W .. FI safety switch .. 230VAC socket
Mast step
ASK 7 lid flipped open
The open lid can be fixed to a horizontal position, using a nylon string. Thus, you have a work surface for your splice box or to safely deposit your tools or other small parts. Errors and technical changes excepted
LightDec GmbH & Co. KG Stand 02/2014
Robert-Bosch-Str. 6 | 85053 Ingolstadt | www.lightdec.de |
[email protected] Tel.: 0049 / 841 / 97475 -29 | Fax.: 0049 / 841 / 97475 -43
®
SWEEDER 4
art. no.: 5827 .de
Multifunctional Interface for Fiber Optic Technology SWEEDER® 4 is a combination of: • a quadruple switch •• a fiber connector (serves also as media converter) ••• a PoE++ supply up to 4 x 45 Watt (2 x 90 Watt)
•
a quadruple switch 10/100 High data throughput via Fast Ethernet Technology Auto MDI – MDIX with 10/100 Mbit/s support Full-duplex standard data transfer up to 100 Mbit/s
ASK with two mounted SWEEDER® 4 moduls
supported standards: ... IEEE 802.3i 10BASE-T Ethernet ... IEEE 802.3u 100BASE-TX Fast Ethernet ••
The optical fiber connection uses pluggable SFP transceiver modules allowing for simplex or duplex mode. Since the use of SFP-modules is an optional offer, already tried and tested own SFPmodules may also be used.
••• SWEEDER® 4 is universally usable since it corresponds to the PoE norms af and at; however, it is particularly designed for PoE++enabled devices, such as cameras, weather proof housing, spotlights etc. PoE standards:
…af …at …PoE++
up to 15 Watt up to 25 Watt up to 90 Watt
It is, in fact, comfortably usable for the SHELTER weatherproof series. Using the PoE SEVEN-V wall arm, the SHELTER camera weatherproof housing and a SEVEN-V spotlight can be operated with just one single Ethernet cable cable. This means that not only the camera and the heating but also the spotlight are power supplied via a single Ethernet cable. And, in spite of that, camera data and the spotlight control system can be accessed and controlled at the same time.
Errors and technical changes excepted
LightDec GmbH & Co. KG Stand 02/2014
Robert-Bosch-Str. 6 | 85053 Ingolstadt | www.lightdec.de |
[email protected] Tel.: 0049 / 841 / 97475 -29 | Fax.: 0049 / 841 / 97475 -43
