Preview only show first 10 pages with watermark. For full document please download

π H-3069 Kihlberg Pneumatic Plier Stapler

   EMBED


Share

Transcript

π H-3069 KIHLBERG PNEUMATIC PLIER STAPLER 1-800-295-5510 uline.com OPERATION loading the magazine 1. Pull the magazine lid (A) all the way out. (See Figure 1) 3. Push the lid all the way forward until it clicks into place. (See Figure 3) Figure 3 Figure 1 A 2. Place the staple strip (B) into the staple rail (C) from the left side. (See Figure 2) Figure 2 B C USING THE STAPLER WARNING! Place the stapler on a stable work surface. Do not drive staples into hard or brittle materials. Do not drive staples at too steep an angle or too close to the edge of the work. Doing so may cause injury. Be sure that the stapler is not pointed at yourself or anyone else when connecting it to the compressed air line. To avoid damage, never fire the stapler when it is empty. 1. Adjust the air pressure to the lowest setting to drive the staples to the desired depth. Start at approximately 5.5 bar and raise by 0.5 bar increments until the correct operating pressure is found. CAUTION! Never exceed 7 bar air pressure. PAGE 1 OF 3 0612 IH-3069 OPERATION CONTINUED 2. Place the item to be stapled (D) below the stapler head (E). (See Figure 4) Pull the trigger (F). Figure 4 REMOVING STUCK STAPLES WARNING! Always disconnect the tool from the air supply, empty the magazine, and read the safety warnings before troubleshooting. 1. Pry the door open from the lefthand side with a screwdriver. 2. Remove any staple remnants inside the tool nozzle and close the door again until it clicks shut. F E D safety warnings NOTE: Read the following warnings to prevent injuries to yourself and those around you. • Never use oxygen, combustible gases, CO 2, steam or high pressure gas tanks as power sources. The stapler may explode and cause serious injury. • Use only dry, clean, pressure-regulated compressed air to drive the stapler. • Eye protection must always be worn by the operator and others in the work area. • Never point the stapler at yourself or anyone else, whether it contains staples or not. Always remove finger from trigger when not driving staples. • Connect the stapler to the compressed air line before loading staples. Maximum air pressure is 7 bar. • Ensure that the air hose has the right dimension to avoid pressure drops which might cause malfunctioning. Minimum: ¼”. • Always use personal protection equipment as required, such as ear protection, hard hats, etc. • The stapler and the hose must have a coupling which automatically bleeds all air pressure from the stapler when it is disconnected. • Never use a defective stapler. Ensure the trigger operates properly and all screws and nuts are securely tightened at all times. • Avoid personal injury. Never hold your hand in the jaws of the stapler. • Do not modify the stapler. • Always disconnect the stapler from the air supply and empty the magazine when the stapler is not in use or when servicing. • Do not load the stapler with the trigger depressed. • Use only Josef Kihlberg staples, type 777. • Always place yourself in a firmly balanced position when using or handling the stapler. • Never leave a loaded stapler unattended. • Always assume that the stapler is loaded. • No horseplay. Respect the stapler as a working implement. PAGE 2 OF 3 0612 IH-3069 MAINTENANCE • Always disconnect the tool from the air supply, empty the magazine and read the safety warnings before starting maintenance. • A small amount of lubricating oil is needed in the nipple each day or 10 drops once a week to ensure safe functioning. • Check that all safety devices function properly, especially that the trigger moves freely and that all screws and nuts are securely tightened. • At high frequency stapling lubricating oil is recommended. • This tool does not require special servicing. It only needs regular cleaning with a non-corrosive cleaning agent. Do not remove any parts for cleaning purposes. • Contact Uline for more information: 1-800-295-5510. SPECIFICATIONS MFG. Part No. Height Length Width Weight Staples Length Magazine Capacity JK20T777L 250mm 375mm 68mm 2,1kg 777 8–16mm 100 • Air pressure: - Approx. 5-6 bar working pressure - 7 bar maximum air pressure • Magazine loading: Loaded from above • The stapler is designed for use with original Josef Kihlberg staples only • Air consumption per shot. :0,3 l at 6 bar operating pressure • Firing of the stapler: Single shot firing π CHICAGO • ATLANTA • DALLAS • LOS ANGELES • MINNEAPOLIS • NYC/PHILA • SEATTLE • MEXICO • CANADA 1-800-295-5510 PAGE 3 OF 3 uline.com 0612 IH-3069