Transcript
INSTRUCTIONS AND PARTS MANUAL
PIPE BUG
Please record your equipment identification information below for future reference. This information can be found on your machine nameplate. Model Number Serial Number Date of Purchase Whenever you request replacement parts or information on this equipment, always supply the information you have recorded above.
A DIVISION OF WELD TOOLING CORPORATION
3001 WEST CARSON STREET PITTSBURGH, PENNSYLVANIA USA 15204-1899 PHONE: 1- 800-245-3186 http://www.bugo.com TELEFAX: 1- 412- 331- 0383
Table of contents Section
Description
Table of contents 1.0 General Information 2.0 Specification 2.1 General Specification 2.2 Feature Table 1 Chain Length Table Table 2 Cutting Tips Table 2.4 Dimension and weight 3.0 Operating Instruction 3.1 Chain length 3.2 Lengthen & shorten drive chain 3.3 How to fit the machine onto pipe 16” and smaller 3.4 Installation of Guide Strip 3.5 How to fit the cutting torch 3.6 – 3.7 The cutting process 3.7 – 3.9 Disassembly after use 4.0 Safety 4.1 Accident prevention rules Use condition 5.0 5.1 Provided use condition 6.0 Maintenance 6.1 Routine maintenance 7.0 Not Allowed Uses 8.0 Exploded drawing of Pipe Bug 8.0 Figure 3 – Base Unit Figure 4 – Exploded drawing of 230 vac Motorized Pipe Bug Figure 5 – Exploded drawing of 115 vac Motorized Pipe Bug Figure 6 – Pipe Bug Accessories 9.0 Parts List 9.1 Table 4 – Main components of Pipe Bug Table 4.1 – Main components of Pipe Bug (continued) Table 5 – Motorized Pipe Bug Components Table 6 – Pipe Bug Accessories Table 7 – Pipe Bug Chain Kits 10.0 Storage of Pipe Bug 10.1 General Information
LIT-PIPE-BUG-IPM-0105
1
Page 1 2 2 2 2 3 3 4 4 4 4 5 6 8 9 9 10 10 11 11 11 11 11 12 12 13 14 15 16 16 17 18 19 20 21 21
1.0 - GENERAL INFORMATION This manual is supplied with the machine. • All operators, maintenance employees and other personnel should read the manual as it concerns safe operation, spare parts and warranty. • The manual should be kept in a clean and humid free environment with easy reach of the operators. • All operators should read the manual prior to attempting to install, use, perform maintenance or dismantle the Pipe Bug. • The supervisor should make sure the operators understand the operation of the machine and oxygen/fuel machine torch. • Do not damage or remove any labels or the nameplate fitted on the machine. • Accidents can be prevented if the operators understand the operation of the machine and cutting torch.
2.0 - SPECIFICATION 2.1 - General Specification The Pipe Bug cutting and bevelling machine is designed to manually rotate an oxygen/fuel machine torch around pipes 3” (88,9 mm.) and larger in diameter. The Pipe Bug can be used with any gas cutting machine torch (acetylene, Butane, propylene, natural gas or propane gas) having a diameter of 35 mm. Pricing for propane or acetylene machine cutting torch is available. If vertical adjustment of the gas cutting torch is necessary a rack can be added to the gas torch.
2.2 - Feature The Main Body, which is an alloy aluminium casting, is fitted with a forwarding device, tensioning screw, wheels and a rack holder-floating device to support the torch. The machine is attached to the pipe to cut by means of a 2-mesh chain along which it moves during the cutting operation. Two hand cranks are used to move the forwarding device composed of a worm screw and a bronze toothed rim that are jointed to the chain pinion. A tensioning screw provides tension to the chain to fix the machine to the pipe. The forwarding device moves upward on two stainless steel columns as tension is applied to the chain. The rack holder floating device provides movement perpendicular to the machine line of travel and a knob with pinion positions it.
2
Table 1. Length of the chain for different pipe-diameter. Pipe diameter* In/mm
2 / 51
3 / 76
4 / 102
6 / 152
8 / 203
10 / 254
12 / 305
Wheel Position
1
1
2
2
2
2
2
23
26
27
34
40
46
52
584
660
686
865
1016
1168
1321
Pipe diameter* In/mm
16 / 406
18 / 457
20 / 508
22 / 559
24 / 610
26 / 660
28 / 711
Wheel Position
2
2
2
2
2
2
2
Chain length In/mm
62
68
74
80
86
92
98
1575
1727
1880
2032
2184
2337
2489
Pipe diameter* In/mm
30 / 762
32 / 813
36 / 914
40 / 1016
42 / 1067
48 / 1219
52 / 1321
Wheel Position
2
2
2
2
2
2
2
Chain length In/mm
104
110
123
135
141
159
171
2642
2794
3124
3429
3581
4039
4368
Chain length In/mm
*The pipe diameter listed is the nominal pipe size; for the actual pipe outside diameters see a commercial pipe chart.
3
2.4 - Dimension and weight
Dimension Description Longitudinal wheel distance (Position 1) (Position 2) Total Height Transversal wheel distance Torch Arm Clearance Clearance parallel to pipe axis
In / mm A : 4 5/16 / 110 B : 5 5/16 / 135 C : 14 5/8 / 372 D : 8 1/16 / 205 E : 13 5/16 / 338 D&E : 22 / 559 F : 21 3/8 / 543
Machine Description Manual model with Gas Torch 115vac motorised model with Gas Torch 230vac motorised Model with Gas Torch Manual model without Gas Torch 115vac motorised model without Gas Torch 230vac motorised model without Gas Torch
Net Weight of base unit (does not include chain) : 38 lbs. (17 kg) : 42 lbs. (19 kg) : 42 lbs. (19 kg) : 34 lbs. (15 kg) : 38 lbs. (17 kg) : 38 lbs. (17 kg)
Shipping Dimensions and weights Packaging size Model with Gas Torch Model without Gas Torch Motorized Model with Gas Torch Motorized Model without Gas Torch Power Supply Unit (shipping dimensions) Power Supply Unit : Steel Carrying Case (shipping dimensions) Steel Carrying Case
: 10” x 10” x 18” (254 x 254 X 457mm) : 40 lbs. (18 kg) / Includes chain : 36 lbs. (16 kg) / Includes mesh chain : 74 lbs. (34 kg) : 70 lbs. (32 kg) : 14 1/2" x 8 5/8” x 7 1/4” (370 x 20 x 185mm : 17 lbs. (98kg) : 21” x 19” x 17” (520 x 475 x 415mm) : 33 lbs. (15 kg)
3.0 - OPERATING INSTRUCTION 3.1 - Chain length Drive chain length required is determined by the diameter of pipe to be cut. Table 1 of the Section 2.2 shows the chain length for various diameters of pipe.
3.2 How to lengthen/shorten the Drive Chain. From Table 1 of the Section 2.2, select the drive-chain length required. If the chain length is incorrect, proceed as follows:
•
To lengthen the riveted drive-chain.
- Select the chain segments required to extend the chain to the length mentioned in Table 1 of the Section 2.2.
4
- Join the chain segments with chain junction link (N21/B) or joint bolt and nut (N21/A). - Set the chain segment, which is the proper length in the chain unpinning block (N20) and remove the chain pin with the pin extractor (N20/A). If one pin is removed the chain is joined with the joint bolt and nut (N21/A). If two pins are removed the chain is joined with the chain junction link (N21/B). - Check that the chain ends to make sure that they meet your application requirement. For male/female chain ends joint bolt and nut (N21/A) and for female to female chain ends use chain junction link (N21/B). • To lengthen the cottered drive-chain. • To shorten the riveted drive c8anbETEMC/P< BDCB57.681 1 Tf 0 Tc 0 Tw 9 0 0
3.4 When cutting pipe under the follow conditions the Pipe Bug Guide Strip is recommended. If the pipe to be cut is spiral welded, severely out of round, in vertical or oblique position and when cutting pipes larger than 18” (457mm) it will be necessary to use a guide strip is necessary to fit the guide belt. - Check the 8” – 18” (203-457mm) away from the cut line where the Pipe Bug guide strip will fit on the pipe for concave or convex areas in the pipe surface. Remove as much of the deformity that is allowed by the welding specification. Warning: Placing the machine on the portion of the pipe, which is being cut off will result in unrepairable damage to the Pipe Bug. See table 3.4 Guide Strip Sections Required for a given Diameter - Form all sections of the guide strip so that they fit the pipe diameter to be cut as close as possible. The better the sections of the guide strip fit the diameter of the pipe; the easier it will be to latch the ends of the guide strip together. - Attach the sections of the guide strips together as shown in Figure 1 with the washer (C1) in between the band end pivot points and insert the pins (C2). The section containing the latch handle assemblies (B) should be at one end of the assembled guide strip and the section containing the receiver section ends (A) should be at the other end. Repeat this step for each section to be assembled.
FIGURE 1 - It may be necessary to move the latch handle assemblies in order to latch the guide strip around the diameter. To move the latch handle assemblies to their proper location, remove the counterscrews and domed nuts (D) from the latch handle assemblies (B) shown Figure 2 and remove the latch assemblies from the guide strip. - Place the section (G) containing the latch handle assemblies (B) over the section containing the latch end (A). - Fold the latch handles (E) of the assemblies over until it touches the screws (F) of the latch adjustment. - Place the end of the latch adjustment screws (F) of the latch handle assemblies into the curved portion of the latch end (A).
6
Figure 2 - Place the latch handle assemblies (B) base over the guide strip from which it was removed. - Locate the nearest holes (G) in that section of the guide strip and mark them. - Place the latch handle assemblies (B) base over the marked holes and insert countersunk screws and nuts (D) in the latch handle assembly base. Tighten the domed nuts on the screws. - Place the end of the latch adjustment screws (F) of the latch handle assemblies into the curved portion of the latch ends (A). - Adjust the end of the latch adjustment screws (F) until the handle of latch handle assembly will lock in position. - Place the Pipe Bug over the guide strip. - Pull the drive chain through the cavity between the sliding core (3M) and the sprocket until 12” – 18” of the chain is protruding out of the other side. - Lay the chain to rest on the sprocket the sprocket. - Place the chain between the dome nuts located near the center of the guide strip. - Connect the chain ends. - Rotate the tensioning handwheel applying tension to the chain. - Cut the chain to length and insert the conn-link. - The Pipe Bug is now ready for the installation of the fuel torch.
7
Table 3.4 Guide Strip Sections required for a given diameter Pipe Diameter In / mm
Head Section 05-0520-013B
Tail Section 05-0520-013D
Short Center Section 05-0520-013C
Long Center Section 05-0520-013A
18 / 457
1
1
****
****
20 / 508
1
1
****
****
24 / 610
1
1
****
****
28 / 711
1
1
1
****
30 / 762
1
1
1
****
32 / 813
1
1
1
****
34 / 864
1
1
****
1
36 / 914
1
1
****
1
42 / 1067
1
1
2
****
48 / 1219
1
1
1
1
52 / 1321
1
1
****
2
54 / 1372
1
1
2
1
58 / 1473
1
1
2
1
60 / 1524
1
1
1
2
3.5 Assembling the Cutting Torch to the Pipe Bug The 1 3/8” (35mm) torch holder (17) is equipped with a knob with 32 pitch or metric pinion (17/A) to adjust the gas torch tip to pipe height. - Verify that the torch tip is appropriate for the type of gas and for the thickness of the pipe to cut. - See the torch manufacturer’s instructions for proper use of the gas cutting torch. - A plasma cutting system with machine cutting torch can be used with the Pipe Bug to cut stainless steel and non-ferrous pipes. - Use the correct the gas for the type of torch purchased - Set gas and oxygen regulators to the pressure specified by the manufacturer for the type of gas that is being used. - Move the knob (29M) to check the torch arm tension and adjust as needed. - Install the torch into the torch holder (17) and rotate the knob with pinion (17/A) to adjust the gas torch tip to pipe height.
8
3.6 STARTING THE MANUAL CUTTING PROCESS - Light the gas torch per the manufacturer’s instructions. - Preheat the pipe to the desired temperature. - Rotate the crank handle while applying the cutting oxygen to the gas torch to minimize notching of the pipe. - Rotate the Pipe Bug crank handle until the cut is complete. - Turn off the cutting oxygen valve as soon as the cut is complete - Turn of the gas and oxygen to the gas torch. 3.7 STARTING THE 230VAC MOTORIZED CUTTING PROCESS - Connect the power supply (28) to the Right Angle drive motor (22/B). - Connect the remote control pendent (27A) to the power supply (28) - Connect the power supply (28) to the 230vac electrical source. - Move the power switch (27/C) to the on position. - Move the forward/reverse switch (27/D) to the forward or reverse position to check functionality of the equipment. Increase the Speed regulator as needed. - Light the gas torch per the manufacturer’s instructions. - Preheat the pipe to the desired temperature. - Rotate the crank handle while applying the cutting oxygen to the gas torch to minimize notching of the pipe. - Rotate the Pipe Bug crank handle until the cut is complete. - Turn off the cutting oxygen valve as soon as the cut is complete - Turn of the gas and oxygen to the gas torch. 3.7 STARTING THE 115VAC MOTORIZED CUTTING PROCESS - Connect the Motor control box (27/A1) to the Right Angle drive motor (22/B2). - Connect the motor control box (27/A1) to the 115vac electrical source. - Move the forward/reverse switch to the forward or reverse position to check functionality of the equipment. Increase the Speed regulator as needed. - Light the gas torch per the manufacturer’s instructions. - Preheat the pipe to the desired temperature. - Move the forward/reverse switch to the desired direction, while applying the cutting oxygen to the gas torch to minimize notching of the pipe. - Rotate the Pipe Bug around the pipe until the cut is complete. - Turn off the cutting oxygen valve as soon as the cut is complete - Turn of the gas and oxygen to the gas torch.
3.7 DISASSEMBLY MANUAL MODEL AFTER USE -
Remove the cutting torch form the torch holder (17). Check the functionality of the gas torch and cutting tip. Rotate the tensioning levers (8E) simultaneously releasing the chain tension. Remove the joint bolt and nut (21A) or junction link (21B) from the chain. Remove the Pipe Bug base unit from the pipe. If used remove the Guide Strip from the pipe by releasing the both latch handle assemblies (B).
9
3.8 DISASSEMBLY 230VAC MOTORIZED MODEL AFTER USE -
Move the power switch (27/C) to the on position. Disconnect the power supply (28) to the 230vac electrical source. Disconnect the power supply (28) to the Right Angle drive motor (22/B). Disconnect the remote control pendent (27A) to the power supply (28) Remove the cutting torch form the torch holder (17). Check the functionality of the gas torch and cutting tip. Rotate the tensioning levers (8E) simultaneously releasing the chain tension. Remove the joint bolt and nut (21A) or junction link (21B) from the chain. Remove the Pipe Bug base unit from the pipe. If used remove the Guide Strip from the pipe by releasing both latches.
3.9 DISASSEMBLY 115VAC MOTORIZED MODEL AFTER USE -
Move the forward/reverse switch to the off position. Disconnect the motor control box (27/A1) from the 115vac electrical source. Disconnect the Motor control box (27/A1) from the Right Angle drive motor (22/B2). Remove the cutting torch form the torch holder (17). Check the functionality of the gas torch and cutting tip. Rotate the tensioning levers (8E) simultaneously releasing the chain tension. Remove the joint bolt and nut (21A) or junction link (21B) from the chain. Remove the Pipe Bug base unit from the pipe. If used remove the Guide Strip from the pipe by releasing both latches.
4.0. - SAFETY DEVICES 4.1 Accident prevention rules. For the safety of the operators, who use the Torch Pipe –Pipe Bug, the operator should follow all shop, national and manufacturer standard safety procedures such as: 1. Persons in the work area should always wear safety equipment such as safety glasses or face shield, gloves, safety shoes and clothing suitable for the work environment and the ambient temperature. 2. All the personnel, who are working around the machine, while the machine is operating, should wear safety glasses for eye protection. 3. Before starting the cutting operation, check all connections to the torch and oxygen and gas regulators. 4. The cutting speed must be properly selected considering the thickness of the pipe to cut. 5. Keep the work area clear of all flammable material. 6. Always wear safety when removing slag, grinding dust and other debris from the work area. 7. Make sure the Pipe Bug, torch, regulators and hoses are properly maintained. 8. During the cutting process, all the personnel not associated with the process must stay at a safe distance. IN ADDITION OF THE ABOVE PROCEDURES, ALL SHOP, NATIONAL AND MANUFACTURER’S SAFETY INSTRUCTIONS CONCERNING THE FLAME CUTTING SYSTEM SHOULD BE FOLLOWED. ALL CUTTING OPERATIONS SHOULD BE CONDUCTED IN THE BEST OF SAFETY CONDITIONS.
10
5.0 – CONDITIONS OF USE 5.1 Provided use condition The Pipe Bug cutting machine has been designed to cut metal pipe having minimum nominal pipe diameter of 2 1/2” (63 mm). Don’t fit the guide belt and the drive chain on heavily crushed pipe or pipe having weld crown in excess of 3/8” (9.5mm) in order to avoid disfigurement of the guide strip and overloading of the drive chain. Cutting of vertical pipe should not be attempted without the use the Mini Guide strip.
6.0. - MAINTENANCE 6.1 Routine Maintenance - Routine maintenance should be planned in advance to avoid down time. - The period between Routine maintenance checks should be shortened if the machine is in constant use. - Check the machine to make sure to insure it has not been dropped. - During the routine maintenance inspection replace all worn parts. - Maintain the gas torch and the oxygen and gas regulators per the manufacturer’s instructions. - The oxygen and gas hoses should be checked daily for burns and abrasions. - Oxygen and gas bottles should be checked in accordance to the safety standard.
7.0 - NOT ALLOWED USE The Pipe Bug machine has been specially designed to cut and bevel pipes. Never to be used in presence of gas or inflammable liquid or solid. Check any time for clearance. Any obstacle must be removed before operation. Flame torch must never be positioned in direction to the operator or other people. Never use torch with inappropriate gas. Never use wrong tip. Switch off the equipment anytime to get near the machine for maintenance.
11
8.0 – Exploded drawing of the Pipe Bug and components Figure 3 Base Machine
12
Figure 4 – 230vac Motorized Pipe Bug Machine
13
Figure 5 – 110vac Motorized Pipe Bug
14
Figure 6 – Pipe Bug Accessories
15
9.0 – PARTS LIST 9.1 - Main components of the Pipe Bug Table 4 - Components of the Pipe Bug (See Figure 3) Item N1 N2 N3 3B 3C 3D 3E 3F 3G N4 N4/A N4/B N4/C N4/D N4/E N5 N5/A N6 N6/A N7 N7/A N8 N8/A N8/B N8/C N11 N11/A N11/B N11/C N11/D N11/E N12 N12/A N12/B N12/C 14 14/A 14/B 14/C 14/D 17 17/A
Description Aluminium Main Frame Right Block Left Block Bearing Flange Bronze Tooth Rim Worm Gear Bearing Screw, M4 x 8 Pinion Holder Shaft Pinion Locking Pin Key, 5 x 5 x 18mm Seeger, Dia. 15mm Flange Column Screw, M8 x 15 Clamping Plate Screw, M6 x 12 Cover Plate Screw, M8 x 15 (See N5/A) Tensioning screw, M12 x 140 Tensioning Hand-wheel Spring Washer Wheel Axel Bronze Bushing Collar Washer Screw, M6 x 12 (See N6/A) Rack Holder Floating Device Gear Rack Screw, M5 x 12 Countersunk screw, M3 x 10 Torch for Torch Holder (complete) Socket Set Screw, M6 x 15 Knob with Metric Gear & Locking Pin Brass Slide Socket Set Screw, M4 x 15 35mm Torch Holder with 32 Pitch Pinion (complete) 35mm Torch Holder with metric pinion (complete) Knob with 32 Pitch Gear & Locking Pin Knob with Metric Gear & Locking Pin
16
Part Number 05-0520-1N1 05-5201N2 05-5201N3 05-510-103B 05-0510-103C 05-010-103D 05-0510-103E 05-0510-103F 05-0510-103G 05-0520-1N4 05-0520-1N4A 05-0520-1N4B 05-0520-1N4C 05-0520-1N4D 05-0520-1N4E 05-0520-1N5 05-0520-1N5A 05-0520-1N6 05-0520-1N6A 05-0520-1N7 05-0520-1N5A 05-0520-1N8 05-0520-1N8A 05-0520-1N8B 05-0520-1N8C 05-0520-1N11 05-0520-1N11A 05-0520-1N11B 05-0520-1N11C 05-0520-1N11D 05-0520-1N6A 05-0520-1N12 05-0520-1N12A 05-0520-1N12B 05-0520-1N12C 05-0510-114 05-0510-114A 05-0510-114B 05-0510-114C 05-0510-114D 05-0510-117 05-0510-117E 05-0510-117A 05-0510-117F
Table 4.1 - Components of the Pipe Bug (See Figure 3) Item 17/B 17/C 19
19/A 19/B 19/C 19/D N20 N20/A N20/B 21 N21/A N21/A1 N21/A2 N21/B N21/C 24 24/A 24/B 24/C N/25 N/25A 60/A 60/B 60/C 60/D 60/E
Description Plastic Locking Knob Metal Locking Knob Screw, M6 x 20 American Torch, dia. 35mm European Torch, dia. 35mm American Torch, dia. 35mm with 32 Pitch Rack European Torch, dia. 35mm with Metric Rack Locking Nut, “H” Cutting Tip Locking Nut, “S” Cutting Tip Cutting Tip Screw, 32 Pitch Rack (specify torch make & model ) Screw, Metric Rack 1,5 x 5 Rack, Torch 32 Pitch (specify torch make & model ) Rack, Torch Metric Pitch Pin Extractor Block with Extractor Pin (compete) Pin, Extractor Block, Pin Extractor 2-Mesh Chain Joint Bolt and Nut (complete) Joint Bolt Joint Nut Connecting Link Chain Junction Link Crank Handle (complete) Revolving Handle Socket Set Screw, M3 x 8 Crank Handle Frame Hose Support Screw, M5 X 22 N° 2 Hex Key N° 3 Hex Key N° 4 Hex Key N° 5 Hex Key N° 6 Hex Key
17
Part Number 05-0510-117A 05-0510-117 05-0520-117C
See Table 2
05-0520-009 05-0520-1N20 05-0520-1N20A 05-0520-121 05-0520-1N21A 05-0520-1N21A1 05-0520-1N21A2 05-0520-1N21B 05-0520-1N21C 05-0510-124 05-0510-124A 05-0510-124B 05-0510-124C 05-0520-1N25 05-0520-1N25A 05-0510-160A 05-0510-160B 05-0510-160C 05-0510-160D 05-0510-160E
Table 5 – Motorized Pipe Bug Machine Components (See Figure 4 and 5) Item
22 22/A 22/B 22/C 27 27/B 27/C 27/D 27/E 28 28/A 28/B 28/C 28/D 28/F 28/G 28/H 28/I 28/L
Description Motorizing Kit, 115 VAC Motorizing Kit, 230 VAC with 2 wall sockets (CE) Motorizing Kit, 230 VAC with 3 wall sockets (CE) Motor Adapter Flange (115VAC) Motor Adapter Flange (230VAC) Motor Coupling Sleeve (115VAC) Motor Coupling Sleeve (230VAC) Motor, Right Angle 90 volts DC (115VAC) Motor, Right Angle 50 volts DC (230VAC) Screw, M3 X 8 Motor Control Box (115VAC) Remote Control Box (230VAC) Pilot Lamp (2302VAC) Power Switch (230VAC) Forward Control (230VAC) Speed Regulator (230VAC) Power Supply Cabinet , 2 Sockets Power Supply Cabinet , 3 Sockets Motor Power Supply Socket Auxiliary 230V Socket Auxiliary 230V Socket General Power Switch Cable Restraint Power Supply Unit Fuse Transformer 500 Amperes Transformer 900 Amperes Step-Down Transformer
18
Part Number 05-0510-A01 05-0510-A02 05-0510-A03 05-0510-014 05-0510-122 05-0510-015 05.0510.122A 03-0201-056 05-0510-122B 05-0520-122C 03-0203-009 05-0510-081
05-0510-073 05-0510-086
05-0510-087
Table 6 Accessories of the Pipe Bug (See Figure 6) Item Description N35/A Guide Strip, 18”- 32” (457 – 813mm) N35/B Guide Strip 18” – 48” (457 – 1219mm) Head Section, Guide Strip (SEE Table 3.4) Tail Section, Guide Strip (SEE Table 3.4) Short Center Section, Guide Strip (SEE Table 3.4) Long Center Section, Guide Strip (SEE Table 3.4) 36 9 foot (3m) Flexible Drive Cable Assembly (complete) 14 foot (3m) Flexible Drive Cable Assembly (complete) Adapter, Cable Drive Adapter, Cable Drive (European) Coupling, Cable Drive Coupling, Cable Drive (European) 16 Grinding Tool Holder (complete) 16/A Locking Knob with Screw 16/B Locking Knob with Screw 37/B Grinding Tool Holder (European) 37/C Portable Right Angle Grinder, 230 V 37/D Grinding Wheel 38/C Portable Right Angle Grinder, 48 V Steel Storage Case (not shown)
19
Part Number 05-0520-012 05-0520-013 05-0520-013B 05-520-013D 05-0520-013C 05-0520-013A 05-0510-FDC 05-0510-FD14 05-0510-010 05-0510-010 05-0510-116 05-0510-116A 05-0510-116B
05-0520-BOX
Table 7 – Pipe Bug Chain Kits Item 21 N21/A N21/A1 N21/A2 N21/B N21/C
Description 2-Mesh Chain (Sold by Meter) Joint Bolt and Nut (complete) Joint Bolt Joint Nut Connecting Link Chain Junction Link
Wheel Pos 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2 2
Chain Length In/mm 27 / 686 34 / 864 40 / 1016 46 / 1168 52 / 1321 56 / 1422 61 / 1549 67 / 1702 73 / 1854 80 / 2032 86 / 2184 92 / 2337 98 / 2489 110 / 2794 116 / 2946 122 / 3099 128 / 3251 134 / 3404 141 / 3581 147 / 3734 159 / 4039 165 / 4191 171 / 4343 178 / 4521 184 / 4674 190 / 4826 196 / 4978
Description Chain kit, 4” (102m) diameter pipe Chain kit, 6” (152mm) diameter pipe Chain kit, 8” (203mm) diameter pipe Chain kit, 10” (254mm) diameter pipe Chain kit, 12” (305mm) diameter pipe Chain kit, 14” (356mm) diameter pipe Chain kit, 16” (406mm) diameter pipe Chain kit, 18” (457mm) diameter pipe Chain kit, 20” (508mm) diameter pipe Chain kit, 22” (559mm) diameter pipe Chain kit, 24” (610mm) diameter pipe Chain kit, 28” (711mm) diameter pipe Chain kit, 30” 762mm) diameter pipe Chain kit, 32” (813mm) diameter pipe Chain kit, 34” (864mm) diameter pipe Chain kit, 36” (914mm) diameter pipe Chain kit, 40” (1016mm) diameter pipe Chain kit, 42” (1067mm) diameter pipe Chain kit, 44” (1118mm) diameter pipe Chain kit, 46” (1168mm)diameter pipe Chain kit, 48” (1219mm) diameter pipe Chain kit, 50” (1270mm) diameter pipe Chain kit, 52” (1321mm) diameter pipe Chain kit, 54” (1372m) diameter pipe Chain kit, 56” (1422mm) diameter pipe Chain kit, 58” (1473mm) diameter pipe Chain kit, 60” (1524mm) diameter pipe
20
Part Number 05-0520-121 05-0520-1N21A 05-0520-1N21A1 05-0520-1N21A2 05-0520-1N21B 05-0520-1N21C Part Number 01-0520-004 01-0520-006 01-0520-008 01-0520-010 01-0520-012 01-0520-014 01-0520-016 01-0520-018 01-0520-020 01-0520-022 01-0520-024 01-0520-028 01-0520-030 01-0520-032 01-0520-034 01-0520-036 01-0520-040 01-0520-042 01-0520-044 01-0520-046 01-0520-048 01-0520-050 01-0520-052 01-0520-054 01-0520-056 01-0520-058 01-0520-060
10.0 – Storage 10.1 - General information Lubricate all moving parts of the Pipe Bug Machine with a light coat of oil. Store the machine in a clean, dry, and safe environment. Store the machine in the Pipe Bug machine storage box if the machine will not be used for an extended period of time.
21
