Transcript
Pipe Hangers
Pipe Hangers
Pipe hangers offered in this section are designed to support insulated or non-insulated pipe allowing for vertical adjustment and limited movement in the piping system.
Materials Carbon Steel, Malleable Iron and AISI Type 304 & 316 Stainless Steel are used in the manufacturing of pipe hangers. Other materials are available.
Finishes The standard finishes for mechanical supports are plain steel (oil coated) sometimes referred to as black, Electro-Galvanized Zinc (ASTM B633 SC3), Pre-Galvanized (ASTM A653 G90), Hot-Dip Galvanized After Fabrication (ASTM A123), Red Primer, Plastic Coating, DURA-GREEN™, DURA-COPPER™ and other special coatings are available upon request. Note: Due to the design of some products, (threads, connecting hardware, swivels, etc.) items may or may not be uniformly coated with special finishes i.e. Hot-Dip Galvanized, DURA-GREEN, DURA-COPPER, PVC etc. In some cases, the hanger itself may be coated, however, the hardware may be supplied Electro-Plated, DURA-COPPER Painted or Stainless Steel. Consult B-Line Systems for availability.
Approvals (as noted) Items in this section are Underwriters Laboratories Listed, Factory Mutual Approved, and comply with Federal Specification WW-H-171E & A-A-1192A or Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58. Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
47
Pipe Hangers & Supports
Pipe Hangers Fig. 1CBS - Clevis Pipe Spacer (Cooper B-Line B3100PS) Size Range: Size 1" (25mm) thru 20" (500mm) clevis hanger Material: Steel
Component of State of California OSHPD Approved Seismic Restraints System
Function: Used as a spacer at a seismic brace location to keep clevis hanger from collapsing during seismic event. Approvals: Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to the Seismic Restraint Systems Guidelines. Installation Note: Fig. 1CBS fits easily over the cross bolt and attaches by pinching tabs down. Finish: Pre-Galvanized. Contact B-Line for alternative finishes and materials. Order By: Part number and finish.
1CBS-1
Approx. Wt./100
in.
(mm)
lbs.
(kg)
1”
(25)
3.2
(1.4)
1CBS-11/4
11/4”
(32)
4.1
(1.8)
1CBS-11/2
11/2”
(40)
4.8
(2.2)
2”
(50)
9.4
(4.2)
21/2”
(65)
11.4
(5.2)
3”
1CBS-2 1CBS-21/2 1CBS-3
(75)
13.9
(6.8)
31/2”
(90)
16.0
(7.2)
1CBS-4
4”
(100)
18.0
(8.1)
1CBS-5
5”
(125)
27.3
(12.4)
1CBS-6
6”
(150)
32.5
(14.7)
1CBS-8
8”
(200)
42.5
(19.2)
1CBS-10
10”
(250)
72.7
(32.9)
1CBS-12
12”
(300)
86.3
(39.1)
1CBS-14
14”
(350)
157.6
(71.5)
1CBS-16
16”
(400)
183.7
(83.3)
1CBS-18
18”
(450)
224.6
(101.9)
1CBS-20
20”
(500)
254.0
(115.2)
1CBS-31/2
Pipe Hangers
Pipe Size Part No.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
48
Pipe Hangers B3100 - Standard Clevis Hanger (TOLCO Fig.1)
Component of State of California OSHPD Approved Seismic Restraints System
SLIDE-RITE™ Clevis Hanger Features Pipe will not ‘pinch’ when installing. 15° swing in either direction allows pipe to easily feed thru. Engineered design aligns bolt holes for quicker overhead installation.
A (Rod Size) Hanger Rod Not Included
E
*SLIDE-RITE™ Clevis Hanger design, as shown below, for sizes 2, 21/2, 3, 4, 5 & 6.
B Bottom of pipe to top of hanger. C Center of pipe to top of hanger. D Rod Take-Out Center of pipe to bottom of hanger rod. E Minimum thread length of hanger rod
D
Pat. No. 5,848,770 5,924,655
F Adjustment Top of cross bolt to bottom of hanger rod nut inside the hanger.
C
B
Nominal Pipe Size Part No.
in.
B3100-1/2
1/2"
B3100-3/4
3/4"
(mm)
Rod Size A Std NFPA**
B in.
C (mm)
in.
(54.0)
13/4"
D (mm)
in.
(mm)
(44.4)
15/16"
(23.8) (28.6)
Pipe Hangers
(15)
3/8"-16
3/8"-16
21/8"
(20)
3/8"-16
3/8"-16
21/2"
(63.5)
2"
(50.8)
11/8"
3/8"-16
27/8"
(73.0)
21/4"
(57.1)
13/8"
(34.9)
31/2"
(88.9)
211/16"
(68.2)
113/16"
(46.0)
(101.6)`
31/16"
(77.8)
21/4"
(57.1) (63.5)
B3100-1
1"
(25)
3/8"-16
B3100-11/4
11/4"
(32)
3/8"-16
3/8"-16
B3100-11/2
11/2"
(40)
3/8"-16
3/8"-16
4"
3/8"-16
41/2"
(50)
3/8"-16
(114.3)
35/16"
(84.1)
21/2"
21/2"
(65)
1/2"-13
3/8"-16
53/8"
(136.5)
315/16"
(100.0)
31/16"
(77.8)
B3100-3 *
3"
(80)
1/2"-13
3/8"-16
61/2"
(165.1)
43/4"
(120.6)
315/16"
(100.0)
B3100-31/2
31/2"
(90)
1/2"-13
3/8"-16
71/4"
(184.1)
51/4"
(133.3)
41/16"
(103.2)
(100)
5/8"-11
3/8"-16
73/4"
(196.8)
51/2"
(139.7)
51/2"
(139.7)
(125)
5/8"-11
1/2"-13
83/4"
(222.2)
61/8"
(155.6)
6"
(152.4)
1/2"-13
105/16"
B3100-2 * B3100-21/2
2" *
B3100-4 * B3100-5 *
4" 5"
B3100-6 *
6"
(150)
3/4"-10
(261.9)
615/16"
(176.2)
7"
(177.8)
B3100-8
8"
(200)
3/4"-10
1/2"-13
123/4"
(323.8)
87/16"
(214.3)
71/8"
(181.0)
B3100-10
10"
(250)
7/8"-9
5/8"-11
151/8"
(384.2)
93/4"
(247.6)
83/8"
(212.7)
(300)
7/8"-9
5/8"-11
171/2"
(444.5)
111/8"
(282.6)
911/16"
(246.1) (269.9)
B3100-12
12"
B3100-14
14"
(350)
1"-8
--
193/8"
(492.1)
123/8"
(314.3)
105/8"
B3100-16
16"
(400)
1"-8
--
213/8"
(542.9)
133/8"
(339.7)
119/16"
(293.7)
B3100-18
18"
(450)
1"-8
--
25"
(635.0)
16"
(406.4)
143/16"
(360.3)
(500)
11/4"-7
--
283/4"
(730.2)
173/4"
(450.8)
165/8"
(422.3)
(600)
11/4"-7
--
323/4"
(831.8)
193/4"
(501.6)
185/8"
(473.1)
--
3915/16"
(1014.4)
2415/16"
(633.4)
223/4"
(577.8)
--
46"
(1168.4)
28"
(711.2)
25"
(635.0)
B3100-20 B3100-24
20" 24"
B3100-30
30"
(750)
11/4"-7
B3100-36
36"
(900)
11/4"-7
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
49
Pipe Hangers & Supports
Pipe Hangers Component of State of California OSHPD Approved Seismic Restraints System
B3100 - Standard Clevis Hanger (TOLCO Fig.1) Size Range:
1
/2” (15mm) to 36” (900mm)
Material: Steel Function: Recommended for the suspension of non-insulated pipe or insulated pipe with a B3151 shield. Note: When an oversized clevis is used, a pipe spacer should be placed over the cross bolt to assure that the lower U-strap will not move in on the bolt. When attaching seismic bracing to the clevis hangers, a B3100PS (cross bolt spacer) must be installed. See Seismic Restraints Approval Guidelines. Order pipe sleeves Fig. 1CBS-(pipe size) separately. Approvals: Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to the B-Line/TOLCO Seismic Restraint Systems Guidelines. Underwriter's Laboratories Listed in the USA (UL) and Canada (cUL) for sizes 3/4” (20mm) thru 12" (300mm). Factory Mutual Engineering Approved (FM) for 3/4” (20mm) thru 12” (300mm) pipe. Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 1 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 1. Also available to accommodate rod schedule per per National Fire Protection Association (NFPA) Pamphlet 13. Maximum Temperature: 650°F (343°C). Standard Finish: Plain, Electro-Galvanized, DURA-GREEN™, or Hot-Dip Galvanized also available in Stainless Steel Order By: Part number and finish. For AWWA - Ductile Iron Clevis Hangers, see B3102, page 51. ** Note: Do not use the dimensions shown in the B3100 chart for NFPA hanger sizes. Contact B-Line for NFPA rod sizing on 1/2” (15mm) thru 12” (300mm) pipe. Part numbers will be 1NFPA-pipe size.
in.
Adjustment F
Design Load
Approx. Wt./100
(mm)
in.
(mm)
Lbs.
(kN)
Lbs.
(kg)
(63.5)
7/16"
(11.1)
730
(3.25)
25
(11.3)
B3100-1/2
21/2"
B3100-3/4
21/2"
(63.5)
1/2"
(12.7)
730
(3.25)
29
(13.1)
B3100-1
21/2"
(63.5)
5/8"
(15.9)
730
(3.25)
35
(15.9)
B3100-11/4
21/2"
(63.5)
7/8"
(22.2)
730
(3.25)
40
(18.1)
B3100-11/2
21/2"
(63.5)
13/16"
(30.2)
730
(3.25)
42
(19.0)
B3100-2 *
21/2"
(63.5)
15/8"
(41.3)
730
(3.25)
52
(23.6)
B3100-21/2
21/2"
(63.5)
2"
(50.8)
1350
(6.00)
90
(40.8)
B3100-3 *
21/2"
(63.5)
2"
(50.8)
1350
(6.00)
110
(49.9)
B3100-31/2
21/2"
(63.5)
2"
(50.8)
1350
(6.00)
142
(64.4)
B3100-4 *
21/2"
(63.5)
2"
(50.8)
1430
(6.36)
132
(59.9)
B3100-5 *
21/2"
(63.5)
2"
(50.8)
1430
(6.36)
215
(97.5)
B3100-6 *
3"
(76.2)
2"
(50.8)
1940
(8.63)
320
(145.1)
B3100-8
31/2"
(88.9)
25/16"
(58.7)
2000
(8.89)
485
(220.0)
B3100-10
31/2"
(88.9)
25/16"
(58.7)
3600
(16.01)
846
(383.7)
B3100-12
31/2"
(88.9)
25/8"
(66.7)
3800
(16.90)
1083
(491.2)
B3100-14
4"
(101.6)
27/8"
(73.0)
4200
(18.68)
1432
(649.5)
B3100-16
4"
(101.6)
211/16"
(68.3)
4600
(20.46)
2200
(997.9)
B3100-18
41/2"
(114.3)
315/16"
(100.0)
4800
(21.35)
2500
(1134.0)
(127.0)
53/8"
(136.5)
4800
(21.35)
4400
(1995.8)
*
B3100-20
5"
B3100-24
5"
(127.0)
53/8"
(136.5)
4800
(21.35)
5000
(2268.0)
B3100-30
5"
(127.0)
61/4"
(158.7)
6000
(26.69)
6600
(2993.7)
B3100-36
5"
(127.0
57/16"
(138.1)
6000
(26.69)
8474
(3843.8)
*SLIDE-RITE™ Clevis Hanger design, as shown above, for sizes 2, 21/2, 3, 4, 5 & 6.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
50
Pipe Hangers
E Part No.
Pipe Hangers B3102 - A.W.W.A. Clevis Hanger (TOLCO Fig.1CI) Size Range: 4” (100mm) to 24” (600mm) Function: Recommended for the suspension of flanged or bell and spigot A.W.W.A. cast iron or ductile iron pipe. The O.D. of the A.W.W.A. iron pipe is shown in the data table.
B Bottom of pipe t0 top of hanger.
A (Rod Size) Hanger Rod Not Included
Material: Steel E
C Center of pipe to top of hanger. D Rod Take-Out Center of pipe to bottom of hanger rod.
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 1 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 1.
E Minimum thread length of hanger rod
D
Standard Finish: Plain & Electro-Galvanized. Contact B-Line for alternative finishes and materials.
F Adjustment Top of cross bolt to bottom of hanger rod nut inside the hanger.
C
B
Order By: Part number and finish.
Pipe Hangers
Pipe O.D. Part No.
in.
(mm)
Rod Size A
in.
B 85/16"
C (mm)
in.
D (mm)
in.
B3102-4
4.80
(121.9)
B3102-6
6.90
(175.2)
3/4"-10
105/8" (269.9) 71/16" (179.4) 513/16" (147.6)
B3102-8
9.05
(229.9)
3/4"-10
131/4" (336.5)
85/8"
(219.1)
73/16"
(182.5) 31/2"
B3102-10 11.10 (281.9)
7/8"-9
157/8" (403.2)
101/4"
(260.3) 811/16"
(220.6) 31/2"
B3102-12 13.20 (335.3)
7/8"-9
B3102-14 15.30 (388.6)
1"-8
203/8" (517.5) 125/8" (320.7) 113/16" (281.6)
B3102-16 17.40 (441.9)
1"-8
231/2" (569.9) 1411/16" (373.1) 127/8" (327.0)
B3102-18 19.50 (495.3)
1"-8
255/8" (650.9)
153/4"
B3102-20 21.60 (548.6)
11/4"-7
291/2" (749.3)
189/16" (471.5)
B3102-24 25.80 (655.3)
11/4"-7
33"
(457.2) 115/16" (287.3)
45/8"
E (mm)
5/8"-11
18"
(211.1) 513/16" (147.6)
in.
93/4"
(117.5) 21/2"
(247.6) 31/2"
(400.0) 1315/16" (354.0)
(838.2) 191/8" (508.0)
3"
177/16"
(442.9)
20"
(485.8)
Design Load
Approx. Wt./100
(mm)
in.
F (mm)
Lbs.
(kN)
Lbs.
(63.5)
2"
(50.8)
1430
(6.36)
203
(92.1)
(76.2)
2"
(50.8)
1940
(8.63)
352
(159.6)
(88.9)
21/8"
(54.0)
2000
(8.89)
532
(241.3)
(88.9)
21/4"
(57.1)
3600
(16.01)
800
(362.9)
(kg)
(88.9)
21/4"
(57.1)
3800
(16.90)
1152
(522.5)
4"
(101.6)
27/8"
(73.0)
4200
(18.68)
1449
(657.2)
4"
(101.6)
33/8"
(85.7)
4600
(20.46)
2100
(952.6)
(114.3)
33/8"
41/2"
(85.7)
4800
(21.35)
2294 (1040.5)
5"
(127.0) 413/16" (122.2)
4800
(21.35)
3887 (1763.1)
5"
(127.0)
51/4"
4800
(21.35)
4844 (2197.2)
(133.3)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
51
Pipe Hangers & Supports
Pipe Hangers B3108 - Extended Clevis Hanger (TOLCO Fig.1A)
A (Rod Size) Hanger Rod Not Included
Size Range: 3/4” (20mm) thru 12” (300mm) pipe Material: Steel
B Bottom of pipe to top of hanger. C Center of pipe to top of hanger.
Function: Recommended for the suspension of insulated pipe where the temperature does not require the use of slides, guides, or rollers for movement. Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 1 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 1.
D Rod Take-Out Center of pipe to bottom of hanger rod.
C
E Minimum thread length of hanger rod.
E B
Maximum Temperature: 650°F (343°C). Order By: Part number and finish. For service For Stainless Steel add SS to part number.
F Adjustment Top of cross bolt to bottom of hanger rod nut inside the hanger.
D
Standard Finish: Plain, Electro-Galvanized or Hot Dip Galvanized For service temperatures of 750°F (399°C) thru 1050°F (565°C) specify Type 304 Stainless Steel
in.
(mm)
Rod Size A
in.
B
C (mm)
in.
43/8"
B3108-3/4
3/4"
(20)
3/8"-16
B3108-1
1"
(25)
3/8"-16
43/4" 53/8"
D (mm)
in.
(mm)
(111.1)
313/16"
(96.8)
31/16"
(77.8)
(120.6)
41/16"
(103.2)
31/4"
(82.5) (84.1)
B3108-11/4
11/4"
(32)
3/8"-16
(136.5)
41/2"
(114.3)
35/16"
B3108-11/2
11/2"
(40)
3/8"-16
67/8"
(174.6)
515/16"
(150.8)
51/8"
(130.2)
2"
(50)
3/8"-16
813/16"
(223.8)
75/8"
(193.7)
67/8"
(174.6)
21/2"
(65)
1/2"-13
10"
(254.0)
81/2"
(215.9)
79/16"
(192.1)
105/8"
(269.9)
813/16"
(223.8)
77/8"
(200.0)
(300.0)
91/2"
(241.3)
83/8"
(212.7)
(261.9)
91/8"
(231.8)
(279.5)
911/16"
(246.0) (282.6)
B3108-2 B3108-21/2 B3108-3
3"
(80)
1/2"-13
B3108-4
4"
(100)
5/8"-11
1113/16" 131/8"
(333.4)
105/16"
(365.1)
11"
B3108-5
5"
(125)
5/8"-11
B3108-6
6"
(150)
3/4"-10
143/8"
(200)
3/4"-10
163/4"
(425.4)
123/8"
(314.3)
111/8"
191/4"
(488.9)
1313/16"
(350.8)
125/16"
(312.7)
215/8"
(549.3)
153/16"
(385.8)
135/8"
(346.1)
B3108-8
8"
Pipe Hangers
Nominal Pipe Size Part No.
H Maximum insulation thickness.
B3108-10
10"
(250)
7/8"-9
B3108-12
12"
(300)
7/8"-9
(mm)
in.
(mm)
in.
(mm)
lbs.
(kN)
lbs.
(kg)
E Part No.
in.
F
H
Design Load
Approx. Wt./100
B3108-3/4
21/2"
(63.5)
1/2"
(12.7)
2"
(50.8)
730
(3.25)
45
(20.4)
B3108-1
21/2"
(63.5)
5/8"
(15.9)
2"
(50.8)
730
(3.25)
49
(22.2)
B3108-11/4
21/2"
(63.5)
7/8"
(22.2)
2"
(50.8)
730
(3.25)
55
(24.9)
B3108-11/2
21/2"
(63.5)
13/16"
(30.2)
2"
(50.8)
730
(3.25)
67
(30.4)
B3108-2
21/2"
(63.5)
15/8"
(41.3)
4"
(101.6)
730
(3.25)
83
(37.6)
B3108-21/2
21/2"
(63.5)
2"
(50.8)
4"
(101.6)
1350
(6.00)
177
(80.3)
B3108-3
21/2"
(63.5)
2"
(50.8)
4"
(101.6)
1350
(6.00)
191
(86.6)
B3108-4
21/2"
(63.5)
2"
(50.8)
4"
(101.6)
1430
(6.36)
237
(107.5)
B3108-5 B3108-6
21/2" 3"
(63.5)
(50.8)
(8.63)
302 397
(137.0)
(101.6)
1430 1940
(6.36)
(50.8)
4" 4"
(101.6)
(76.2)
2" 2"
B3108-8
31/2"
(88.9)
25/16"
(58.7)
4"
(101.6)
2000
(8.89)
582
(264.0)
B3108-10
31/2"
(88.9)
25/16"
(58.7)
4"
(101.6)
3600
(16.01)
968
(439.1)
B3108-12
31/2"
(88.9)
25/8"
(66.7)
4"
(101.6)
3800
(16.90)
1221
(553.8)
(180.1)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
52
Pipe Hangers B3100C - Standard Clevis Hanger - Plastic Coated (TOLCO Fig.1PVC) B3100F - Standard Clevis Hanger - Felt Lined for Copper Tubing (TOLCO Fig.1F) Size Range: 1/2” (15mm) to 8” (200mm) pipe Material: Steel
A (Rod Size) Hanger Rod Not Included
E
Insulation Material: 3/16” (4.8mm) Felt Service: The B3100F is designed for the suspension of copper tube so as to prevent electrolysis between tubing and hanger. The B3100C is designed for steel or other pipe types of the same O.D. Both B3100F and B3100C act to reduce noise and vibration in pipe or tubing systems.
D
B Bottom of pipe to top of hanger. C Center of pipe to top of hanger. D Rod Take-Out Center of pipe to bottom of hanger rod. E Minimum thread length of hanger rod
Approvals: Underwriter's Laboratories Listed in the USA (UL) and Canada (cUL).
F Adjustment Top of cross bolt to bottom of hanger rod nut inside the hanger.
C
Maximum Temperature: 650°F (343°C). Standard Finish: Plain, Electro-Galvanized, or Hot-Dip Galvanized. Contact B-Line for alternative finishes and materials.
B
Order By: Part number and finish.
Pipe Size Part No.
Pipe Hangers
B3100-1/2 B3100-3/4 B3100-1 B3100-11/4 B3100-11/2 B3100-2 B3100-21/2 B3100-3 B3100-31/2 B3100-4 B3100-5 B3100-6 B3100-8
in.
(mm)
Rod Size A
1/2"
(15)
3/8"-16
3/4"
(20)
3/8"-16
(25)
3/8"-16
(32)
3/8"-16
(40)
3/8"-16
(50)
3/8"-16
(65)
1/2"-13
(80)
1/2"-13
(90)
1/2"-13
(100)
5/8"-11
(125)
5/8"-11
(150)
3/4"-10
(200)
3/4"-10
1" 11/4" 11/2" 2" 21/2" 3" 1 3 /2" 4" 5" 6" 8" E
Part No. B3100-1/2 B3100-3/4 B3100-1 B3100-11/4 B3100-11/2 B3100-2 B3100-21/2 B3100-3 B3100-31/2 B3100-4 B3100-5 B3100-6 B3100-8
B
C
D
in.
(mm)
in.
(mm)
in.
(mm)
21/8" 27/16" 213/16" 37/16" 4" 1 4 /2" 59/16" 63/4" 7" 713/16" 91/16" 107/16" 123/4"
(54.0)
111/16" 17/8" 21/8" 29/16" 3" 1 3 /4" 4" 47/8" 5" 51/2" 61/8" 615/16" 83/8"
(42.9)
15/16"
(23.8)
(47.6)
11/8" 13/8" 113/16" 21/4" 21/2" 31/16" 315/16" 41/16" 43/8" 5" 11 5 /16" 71/8"
(28.6)
(61.9) (71.4) (87.3) (101.6)` (114.3) (141.3) (171.4) (177.8) (198.4) (230.2) (265.1) (323.8)
Adjustment F
Design Load
(54.0) (65.1) (76.2) (82.5)
(101.6) (123.8) (127.0) (139.7) (155.6) (176.2) (212.7)
(mm)
in.
(mm)
Lbs.
(kN)
Lbs.
(kg)
21/2" 21/2" 21/2" 21/2" 21/2" 21/2" 21/2" 21/2" 21/2" 21/2" 21/2" 3" 31/2"
(63.5)
7/16"
(11.1)
(3.25)
1/2"
(12.7)
(63.5)
5/8"
(15.9)
(63.5)
7/8"
(22.2)
(63.5)
13/16"
(30.2)
(63.5)
15/8" 2" 2" 2" 2" 2" 2" 25/16"
(41.3)
25 29 35 40 42 52 90 110 142 132 215 320 485
(11.3)
(63.5)
730 730 730 730 730 730 1350 1350 1350 1430 1430 1940 2000
(63.5) (63.5) (63.5) (63.5) (63.5) (76.2) (88.9)
(50.8) (50.8) (50.8) (50.8) (50.8) (50.8) (58.7)
(3.25) (3.25) (3.25) (3.25) (6.00) (6.00) (6.00) (6.36) (6.36) (8.63) (8.89)
(46.0) (57.1) (63.5) (77.8) (100.0) (103.2) (111.1) (127.0) (144.5) (181.0)
Approx. Wt./100
in.
(3.25)
(34.9)
(13.1) (15.9) (18.1) (19.0)
B3100C
(23.6) (40.8) (49.9) (64.4) (59.9) (97.5) (145.1) (220.0)
B3100F
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
53
Pipe Hangers & Supports
Pipe Hangers B3690 - J-Hanger for Pipe or Conduit (TOLCO Fig. 3) B3690F - Felt Lined J-Hanger for Copper Tubing (TOLCO Fig. 3F) B3690C - PVC Coated J-Hanger for Pipe or Conduit (TOLCO Fig. 3PVC) Size Range: 1/2” (15mm) to 10” (250mm) pipe size Material: Steel Function: Recommended for the suspension of non-insulated pipe, or insulated pipe with B3151 shield. Side hole allows for wall mounting. B3690F and B3690C are designed to reduce noise and vibration and/or prevent electrolysis between pipe and hanger.
B Center of pipe to top of hanger.
A (Rod Size) Hanger Rod Not Included
F Rod Take-Out Center of pipe to bottom of hanger rod.
Approvals: Conforms Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 5.
C
Standard Finish: Electro-Plated. Contact B-Line for alternative finishes and materials.
D Dia.
Order By: Part number and finish. E
F
B3690F
B3690C
Pipe O.D. Part No.
in.
(mm)
Rod Size A
in.
B 25/8" 27/8"
3/8"-16
B3690-11/4
11/4" (32)
3/8"-16
31/4"
B3690-11/2
11/2"
(40)
3/8"-16
39/16" 311/16"
B3690-3 B3690-31/2 B3690-4
Lbs.
(kg)
(38.1)
115/16"
(49.2)
400
(1.78)
18
(8.1)
(11.1) 111/16" (42.9)
21/8"
(54.0)
400
(1.78)
21
(9.5)
7/16"
(11.1) 113/16" (46.0)
25/16"
(58.7)
400
(1.78)
22
(10.0)
(50.8)
7/16"
(11.1) 21/16" (52.4)
25/8"
(66.7)
400
(1.78)
25
(11.3)
(55.6)
7/16"
(11.1) 27/16"
(61.9)
27/8"
(73.0)
400
(1.78)
27
(12.2)
(11.1) 29/16"
(77.8)
400
(1.78)
29
(13.1)
(47.6)
(25)
B3690-21/2
(kN)
215/16" (74.6) 115/16" (49.2)
(20)
(73.0)
Lbs.
(11.1)
1"
17/8"
(mm)
7/16"
3/8"-16
(66.7)
Approx. Wt./100
in.
(44.4)
(15)
3/4"
13/4"
Design Load
(mm)
11/2"
B3690-3/4
in.
(82.5)
2"
(90.5)
23/16"
(93.7)
21/8"
(112.7)
(mm)
in.
E
7/16"
3/8"-16
(mm)
D in.
1/2"
B3690-2
C
(mm)
B3690-1/2 B3690-1
Pipe Hangers
B
F
(50)
3/8"-16
(54.0)
7/16"
(65.1)
31/16"
21/2"
(65)
1/2"-13
47/16"
27/16"
(61.9)
9/16"
(14.3) 33/16"
(81.0)
35/8"
(92.1)
500
(2.22)
64
(29.0)
3"
(80)
1/2"-13
413/16" (122.2) 29/16"
(65.1)
9/16"
(14.3)
31/2"
(88.9)
41/16" (103.2)
500
(2.22)
72
(32.6)
31/2" (90)
1/2"-13
51/8" (130.2)
25/8"
(66.7)
9/16"
(14.3)
33/4"
(95.2)
43/8"
(111.1)
500
(2.22)
84
(38.1)
(100)
5/8"-11
61/8"
(155.6)
33/16"
(81.0)
9/16"
(14.3)
45/8"
(117.5)
53/16"
(131.8)
550
(2.44)
138
(62.6)
63/4"
(171.4)
31/4"
(82.5)
9/16"
(14.3) 51/16" (128.6)
53/4"
(146.0)
550
(2.44)
162
(73.5)
65/8"
(168.3)
600
(2.67)
249
(112.9)
2"
4"
B3690-5
5"
(125)
5/8"-11
B3690-6
6"
(150)
3/4"-10
73/4" (196.8) 39/16"
(90.5)
9/16"
(14.3) 513/16" (147.6)
B3690-8
8"
(200)
7/8"-9
93/16" (233.4) 315/16" (100.0)
9/16"
(14.3) 615/16" (176.2)
8"
(203.3)
760
(3.38)
291
(132.0)
10" (250)
7/8"-9
103/4" (273.0)
9/16"
75/8"
91/8"
(231.8)
760
(3.38)
315
(142.9)
B3690-10
37/8"
(98.4)
(14.3)
(193.7)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
54
Pipe Hangers B3109 - Flat Top Clevis Hanger Size Range: 2” (50mm) to 8” (200mm) pipe size
A (Rod Size) Hanger Rod Not Included
Material: Steel Function: Recommended for suspending noninsulated, stationary pipe where space is limited. Approvals: Complies with Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58 Type 1.
B Bottom of pipe to top of hanger. C Center of pipe to top of hanger.
C B
Standard Finish: Plain or Electro-Galvanized D
Order By: Part number and finish.
Pipe Size Pipe Hangers
Part No. B3109-2 B3109-21/2 B3109-3 B3109-31/2
in.
(mm)
Rod Size A
in.
(mm)
2"
(50)
3/8"-16
313/16"
(96.8)
21/2"
(65)
1/2"-13
45/8"
(117.5)
(80)
1/2"-13
55/16"
(134.9)
(90)
1/2"-13
513/16"
(147.6)
61/2"
(165.1)
3" 31/2"
B
B3109-4
4"
(100)
5/8"-11
B3109-5
5"
(125)
5/8"-11
713/16"
(198.4)
B3109-6
6"
(150)
3/4"-10
97/16"
(230.2)
(200)
3/4"-10
113/8"
(288.9)
(mm)
in.
(mm)
Lbs.
(kN)
B3109-2
25/8"
(66.7)
17/8"
(47.6)
300
B3109-21/2
33/16"
(81.0)
23/16"
(55.6)
500
B3109-3
39/16"
(90.5)
25/8"
(66.7)
B3109-31/2
313/16"
B3109-8
8"
C Part No.
in.
Rod Take-Out D
Design Load
Approx. Wt./100 Lbs.
(kg)
(1.33)
52
(23.6)
(2.22)
116
(52.6)
500
(2.22)
133
(60.3) (65.8)
(96.8)
27/8"
(73.0)
500
(2.22)
145
B3109-4
41/4"
(107.9)
31/8"
(79.4)
700
(3.11)
180
(81.6)
B3109-5
5"
(127.0)
37/8"
(98.4)
700
(3.11)
248
(112.5)
B3109-6
511/16"
(144.5)
47/16"
(112.7)
900
(4.00)
332
(150.6)
(177.8)
513/16"
(147.6)
1000
(4.45)
513
(232.7)
B3109-8
7"
D Rod Take-Out Center of pipe to bottom of hanger rod.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
55
Pipe Hangers & Supports
Pipe Hangers B3106 - Vee Bottom Clevis Hanger (TOLCO Fig. 1V) Size Range: 1/2” (15mm) to 4” (100mm) pipe
A (Rod Size) Hanger Rod Not Included
Material: Steel Function: Recommended for the suspension of flexible plastic pipe. Use with B3106V support trough for plastic pipe.
E Minimum thread length of hanger rod.
B
Standard Finish: Plain & Electro-Galvanized. Contact B-Line for alternative finishes and materials.
D C
Order By: Part number and finish.
Pipe Size in.
C Center of pipe to top of hanger. D Rod Take-Out Center of pipe to bottom of hanger rod.
Approvals: Complies with Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58 Type 1.
Part No.
B Overall Height
(mm)
Rod Size A
in.
B (mm)
in.
C (mm)
B3106-2
1/2"
to 2"
(15 to 50)
3/8"-16
515/16"
(150.8)
41/16"
(103.2)
B3106-4
21/2" to 4"
(65 to 100)
1/2"-13
93/8"
(238.1)
6"
(152.4)
Part No.
Rod Take-Out D
Adjustment E
in.
(mm)
in.
(mm)
Lbs.
(kN)
Lbs.
(kg)
(84.1)
15/8"
(41.3)
150
(.67)
60
(27.2)
(122.2)
23/16"
(55.6)
150
(.67)
143
(64.8)
B3106-4
413/16"
Approx Wt./100
Pipe Hangers
B3106-2
35/16"
Design Load
B3106V - Plastic Pipe Support Channel (TOLCO Fig. 1VT) Size Range: 1/2” (15mm) to 4” (100mm) pipe Material: Steel TxL Steel Size
Function: Designed for use with B3106 as a support for plastic or other flexible pipe systems. Standard Finish: Pre-Galvanized. Contact B-Line for alternative finishes and materials.
B
Order By: Part number and finish.
For Nominal Pipe Sizes Part No.
Steel Size T x L
Maximum Hanger Spacing
B
Design Load
Approx. Wt./100
in.
(mm)
in.
(mm)
in.
(mm)
Ft.
(M)
Lbs.
(kN)
Lbs.
(kg)
B3106V-2
1/2" to 2"
(15 to 50)
18 Ga. x 96"
(1.2 x 2438.4)
19/16"
(39.7)
8
(2.44)
150
(.67)
449
(203.6)
B3106V-4
21/2" to 4"
(65 to 100)
18 Ga. x 120"
(1.2 x 3048.0)
31/8"
(79.4)
10
(3.05)
150
(.67)
1123
(509.4)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
56
Pipe Hangers B3104 - Light-Duty Clevis Hanger B3104F - Light-Duty Clevis Hanger - Felt Lined B3104C - Light-Duty Clevis Hanger - PVC Coated
A (Rod Size) Hanger Rod Not Included
Size Range: 1/2” (15mm) to 4” (100mm) pipe Material: Steel E
Function: Recommended for the suspension of light stationary pipe allowing for vertical adjustment.
B Bottom of pipe to top of hanger. C Center of pipe to top of hanger.
Approvals: Underwriter's Laboratories Listed in the USA (UL) and Canada (cUL) for sizes 3/4” (20mm) thru 4” (100mm). Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 12 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 1.
D Rod Take-Out Center of pipe to bottom of hanger rod.
D
E Minimum thread length of hanger rod.
C
Standard Finish: Plain, Electro-Galvanized, or DURA-GREEN™
B
Order By: Part number and finish.
F Adjustment Top of cross bolt to bottom of hanger rod nut inside the hanger.
*Slide-Rite™ Clevis Hanger design for sizes 2, 3 & 4. Pat. No. 5,848,770 5,924,655 Pipe Size Part No.
in.
(mm)
Rod Size A
in.
B 115/16"
C (mm)
in.
(mm)
(38.1)
B3104-1/2
1/2"
(15)
3/8"-16
(49.2)
11/2"
B3104-3/4
3/4"
(20)
3/8"-16
25/16"
(58.7)
13/4"
(44.4)
1"
(25)
3/8"-16
23/4"
(69.8)
21/16"
(52.4)
35/16"
(61.9)
B3104-1 Pipe Hangers
B3104-11/4
11/4"
(32)
3/8"-16
(84.1)
27/16"
B3104-11/2
11/2"
(40)
3/8"-16
35/8"
(92.1)
25/8"
(66.7)
B3104-2 *
2"
(50)
3/8"-16
413/16"
(122.2)
35/8"
(92.1)
B3104-21/2
21/2"
(65)
1/2"-13
513/16"
(147.6)
45/16"
(109.5)
B3104-3 *
3"
(80)
1/2"-13
67/16"
(163.5)
45/8"
(117.5)
B3104-31/2
31/2"
(90)
1/2"-13
615/16"
(176.2)
415/16"
(125.4)
(100)
1/2"-13
73/4"
(196.8)
51/2"
(139.7)
B3104-4 *
4"
Rod Take-Out D Part No.
E
Adjustment F
Design Load
B3104C
B3104F Approx. Wt./100
in.
(mm)
in.
(mm)
in.
(mm)
Lbs.
(kN)
Lbs.
(kg)
13/16"
(20.6)
21/2"
(63.5)
7/16"
(11.1)
150
(.67)
13
(5.9)
B3104-3/4
1"
(25.4)
21/2"
(63.5)
7/16"
(11.1)
250
(1.11)
22
(10.0)
B3104-1
13/8"
(34.9)
21/2"
(63.5)
9/16"
(14.3)
250
(1.11)
24
(10.9)
B3104-11/4
13/4"
(44.4)
21/2"
(63.5)
13/16"
(20.6)
250
(1.11)
29
(13.1)
(50.8)
21/2"
(63.5)
1"
(25.4)
250
(1.11)
30
(13.6)
(74.6)
21/2"
(63.5)
13/4"
(44.4)
250
(1.11)
35
(15.9)
B3104-1/2
B3104-11/2
2"
B3104-2 *
215/16"
B3104-21/2
37/16"
(87.3)
21/2"
(63.5)
2"
(50.8)
350
(1.55)
82
(37.2)
B3104-3 *
33/4"
(95.2)
21/2"
(63.5)
2"
(50.8)
350
(1.55)
91
(41.3)
B3104-31/2
4"
(101.6)
21/2"
(63.5)
2"
(50.8)
350
(1.55)
98
(44.4)
B3104-4 *
49/16"
(115.9)
21/2"
(63.5)
23/16"
(55.6)
400
(1.78)
132
(59.9)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
57
Pipe Hangers & Supports
Pipe Hangers B Bottom of pipe to top of hanger.
B3104CT - Clevis Hanger (TOLCO Fig. 81) B3104CTC - Clevis Hanger - PVC Coated (TOLCO Fig. 81PVC)
C Center of pipe to top of hanger. A (Rod Size) Hanger Rod Not Included
Size Range: 1/2” (15mm) to 6” (150mm) copper tubing Material: Steel Function: Recommended for the suspension of non- insulated stationary copper tubing lines. Available with plastic coating to provide additional separation between tubing and hanger.
D Rod Take-Out Center of pipe to bottom of hanger rod.
E
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 12 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 1.
E Minimum thread length of hanger rod.
D
F Adjustment Top of cross bolt to bottom of hanger rod nut inside the hanger.
C
B
Standard Finish: DURA-COPPER™ Order By: Part number and finish.
B3104CTC
in.
(mm)
Rod Size A
in.
B 21/4"
C (mm)
in.
Rod Take-Out D (mm)
in.
(mm)
(28.6)
B3104CT-1/2
1/2"
(15)
3/8"-16
(57.1)
115/16"
(49.2)
11/8"
B3104CT-3/4
3/4"
(20)
3/8"-16
115/16"
(49.2)
11/2"
(38.1)
11/8"
(28.6)
1"
(25)
3/8"-16
25/16"
(58.7)
13/4"
(44.4)
15/16"
(33.3)
B3104CT-11/4
11/4"
(32)
3/8"-16
23/4"
(69.8)
21/16"
(52.4)
19/16"
(39.7)
B3104CT-11/2
11/2"
(40)
3/8"-16
35/16"
(84.1)
27/16"
(61.9)
21/16"
(52.4)
41/2"
(85.7)
B3104CT-1
B3104CT-2 B3104CT-21/2 B3104CT-3 B3104CT-31/2 B3104CT-4
(50)
3/8"-16
(114.3)
37/16"
(87.3)
33/8"
21/2"
(65)
1/2"-13
511/16"
(144.5)
41/2"
(114.3)
315/16"
(100.0)
3"
(80)
1/2"-13
53/16"
(131.8)
35/8"
(92.1)
4"
(101.6)
(90)
1/2"-13
61/2"
(165.1)
49/16"
(115.9)
41/8"
(104.8)
(100)
1/2"-13
73/8"
(187.3)
35/16"
(134.9)
43/8"
(111.1)
9"
(228.6)
67/16"
(163.5)
53/4"
(146.0)
105/16"
(261.9)
71/4"
(184.1)
61/2"
(165.1)
2"
31/2" 4"
B3104CT-5
5"
(125)
1/2"-13
B3104CT-6
6"
(150)
5/8"-11
E Part No.
in.
Adjustment F (mm)
in.
Design Load
(mm)
Lbs.
Approx. Wt./100
(kN)
Lbs.
(kg)
B3104CT-1/2
21/2"
(63.5)
3/8"
(9.5)
150
(.67)
12
(5.4)
B3104CT-3/4
21/2"
(63.5)
7/16"
(11.1)
250
(1.11)
12
(5.4)
B3104CT-1
21/2"
(63.5)
9/16"
(14.3)
250
(1.11)
22
(10.0)
B3104CT-11/4
21/2"
(63.5)
9/16"
(14.3)
250
(1.11)
24
(10.9)
B3104CT-11/2
21/2"
(63.5)
15/16"
(23.8)
250
(1.11)
30
(13.6)
B3104CT-2
21/2"
(63.5)
13/4"
(44.4)
250
(1.11)
35
(15.9)
B3104CT-21/2
21/2"
(63.5)
21/8"
(54.0)
350
(1.55)
80
(36.3)
B3104CT-3
21/2"
(63.5)
21/16"
(52.4)
350
(1.55)
88
(39.9)
B3104CT-31/2
21/2"
(63.5)
21/8"
(54.0)
350
(1.55)
94
(42.6)
B3104CT-4
21/2"
(63.5)
21/8"
(54.0)
400
(1.78)
116
(52.6)
B3104CT-5
21/2"
(63.5)
21/2"
(63.5)
550
(2.44)
208
(94.3)
B3104CT-6
21/2"
(63.5)
3"
(76.2)
550
(2.44)
247
(112.0)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
58
Pipe Hangers
Tubing Size Part No.
B3104CT
Pipe Hangers Fig. 2 - Adjustable Band Hanger (B-Line B3170) Fig. 2F - Adjustable Band Hanger Felt Lined for Copper Tubing (B-Line B3170F) Size Range: Fig. 2 - 21/2” (65mm) thru 6” (150mm) pipe Fig. 2F - 21/2” (65mm) thru 6” (150mm) pipe C
Material: Pre-Galvanized Steel
B
Function: Recommended for the suspension of noninsulated pipe or insulated pipe with B3151 shield. Fig. 2NFPA accomodates the reduced rod schedule of the National Fire Pretection Association Pamphlet 13.
D
Approvals: Factory Mutual Engineering Approved. Underwriters Laboratories Listed. Conforms to Federal Specification WW-H-171E & A-A-1192A Type 10 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 10.
Fig. 2
Standard Finish: Pre-Galvanized Note: Available in Stainless Steel material. Order By: Part number and finish.
C B
D
Fig. 2F
Fig. 2 Pipe Hangers
Nominal Part No.
in.
Pipe Size
2-21/2
21/2"
2-3 2-31/2 2-4 2-5 2-6
3" 31/2" 4" 5" 6"
(mm)
(65) (75) (90) (100) (125) (150)
Rod Size A
B in.
1/2"-13
53/4"
1/2"-13
6" 73/8" 73/8" 9" 93/8"
* * 1/2"-13 * 5/8"-11 * 5/8"-11 ** 3/4"-10 **
C (mm)
in.
(146.0) (152.4) (187.3) (187.3) (228.6) (238.1)
41/4"
(mm)
in.
(146.0) (152.4) (187.3) (187.3) (228.6) (238.1)
41/4"
41/8" 51/4" 5" 61/8" 61/2"
D
Max. Rec. Load
Approx Wt./100
(mm)
in.
(mm)
lbs.
(kN)
lbs.
(kg)
(107.9) (104.8) (133.3) (127.0) (155.6) (165.1)
15/8"
(41.3) (31.7) (54.0) (41.3) (57.1) (47.6)
600 600 600 1000 1250 1250
(2.67) (2.67) (2.67) (4.45) (5.56) (5.56)
41 45 52 59 97 139
(18.6) (20.4) (23.6) (27.6) (44.0) (63.0)
(mm)
in.
(mm)
lbs.
(kN)
lbs.
(kg)
(107.9) (104.8) (133.3) (127.0) (155.6) (165.1)
15/8"
(41.3) (31.7) (54.0) (41.3) (57.1) (47.6)
600 600 600 1000 1250 1250
(2.67) (2.67) (2.67) (4.45) (5.56) (5.56)
41 45 52 59 97 139
(18.6) (20.4) (23.6) (27.6) (44.0) (63.0)
11/4" 21/8" 15/8" 21/4" 17/8"
Fig. 2F Nominal Part No.
in.
Pipe Size
2F-21/2
21/2"
2F-3 2F-31/2 2F-4 2F-5 2F-6
3" 31/2" 4" 5" 6"
(mm)
(65) (75) (90) (100) (125) (150)
Rod Size A
B in.
1/2"-13
53/4"
1/2"-13
6" 73/8" 73/8" 9" 93/8"
* * 1/2"-13 * 5/8"-11 * 5/8"-11 ** 3/4"-10 **
* 3/8 nut is used when requested.
C
41/8" 51/4" 5" 61/8" 61/2"
D
11/4" 21/8" 15/8" 21/4" 17/8"
Max. Rec. Load
Approx Wt./100
** 1/2 nut is used when requested.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
59
Pipe Hangers & Supports
Pipe Hangers B3170CT - Adjustable Swivel Hanger for Copper Tubing (TOLCO Fig. 202) B3170CTC - Adjustable Swivel Hanger for Copper Tubing - Plastic Coated Size Range: 1/2” (15mm) thru 6” (150mm) copper tubing A (Rod Size) Hanger Rod Not Included
Material: Steel Function: Recommended for the suspension of copper tubing, allowing for vertical adjustment. (Available with plastic coating to provide additional separation between tubing and hanger.)
B Center of pipe to top of knurled hanger rod nut. C Rod Take-Out Center of pipe to bottom of hanger rod.
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 10 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 10.
C
D
D Top of pipe to bottom of hanger rod nut.
B
Standard Finish: DURA-COPPER™ Order By: Part number and finish.
Nominal Pipe Size
Rod Size A
in.
B
C (mm)
in.
21/16"
D (mm)
in.
(mm)
(52.4)
11/8"
(28.6)
31/32"
(24.6)
(58.7)
15/16"
(33.3)
11/32"
(26.2)
(39.7)
15/32"
(29.3)
(39.7)
1"
(25.4) (33.3)
B3170CT-1/2
1/2"
(15)
3/8"-16
B3170CT-3/4
3/4"
(20)
3/8"-16
25/16" 21/2"
(63.5)
19/16"
(63.5)
19/16"
1"
(25)
3/8"-16
B3170CT-11/4
11/4"
(32)
3/8"-16
21/2"
B3170CT-11/2
11/2"
(40)
3/8"-16
215/16"
(74.6)
2"
(50.8)
15/16"
2"
(50)
3/8"-16
31/8"
(79.4)
21/8"
(54.0)
13/16"
(30.2)
21/2"
(65)
1/2"-13
41/16"
(103.2)
29/16"
(65.1)
13/8"
(34.9)
3"
(75)
1/2"-13
315/16"
(100.0)
33/4"
(95.2)
11/4"
(31.7)
31/2"
(90)
1/2"-13
47/16"
(112.7)
31/4"
(82.5)
11/2"
(38.1)
4"
(100)
1/2"-13
411/16"
(119.1)
39/16"
(89.6)
19/16"
(39.7)
515/16"
(150.8)
45/16"
(109.5)
125/32"
(45.2)
611/16"
(169.9)
53/16"
(131.8)
21/8"
(54.0)
B3170CT-1
B3170CT-2 B3170CT-21/2 B3170CT-3 B3170CT-31/2 B3170CT-4 B3170CT-5
5"
(125)
1/2"-13
B3170CT-6
6"
(150)
1/2"-13
Max. Rec. Load Part No.
lbs.
(kN)
B3170CT-1/2
180
B3170CT-3/4
180
B3170CT-1 B3170CT-11/4 B3170CT-11/2 B3170CT-2
Pipe Hangers
Part No.
Approx. Wt./100 lbs.
(kg)
(0.80)
8
(6.6)
(0.80)
10
(4.5)
180
(0.80)
10
(4.5)
180
(0.80)
12
(5.4)
180
(0.80)
12
(5.4)
180
(0.80)
12
(5.4)
B3170CT-21/2
200
(0.89)
31
(24.0)
B3170CT-3
250
(1.11)
33
(14.9)
B3170CT-31/2
300
(1.33)
39
(17.2)
B3170CT-4
360
(1.60)
40
(18.1)
B3170CT-5
480
(2.13)
95
(43.1)
B3170CT-6
630
(2.80)
118
(53.5)
B3170CT
B3170CTC
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
60
Pipe Hangers Fig. 200 - “Trimline” Adjustable Band Hanger (B-Line B3170NF) Fig. 200F - “Trimline” Adjustable Band Hanger with Felt Lining for Copper Tubing (B-Line B3170NFF) Fig. 200C - “Trimline” Adjustable Band Hanger with Plastic Coated (B-Line B3170NFC) Size Range: Fig. 200 - 1/2” (15mm) thru 8” (200mm) pipe Material: Steel, Pre-Galvanized to G90 specifications Function: For fire sprinkler and other general piping purposes. Knurled swivel nut design permits hanger adjustment after installation. Features: • (1/2” (15mm) thru 2” (50mm)) Flared edges ease installation for all pipe types and protect CPVC plastic pipe from abrasion. Captured design keeps adjusting nut from separating with hanger. Hanger is easily installed around pipe. • (21/2” (65mm) thru 8” (200mm)) Spring tension on nut holds it securely in hanger before installation. Adjusting nut is easily removed.
B A
Approvals: Underwriters Laboratories listed (1/2” (15mm) thru 8” (200mm)) in the USA (UL) and Canada (cUL) for steel and CPVC plastic pipe and Factory Mutual Engineering Approved (3/4” (20mm) thru 8” (200mm)). Conforms to Federal Specifications WW-H-171E & A-A-1192A, Type 10 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 10.
Fig. 200-21/2 to 200-8
Fig. 200-1/2 to 200-2
Maximum Temperature: 650°F (343°C) Finish: Pre-Galvanized. Stainless Steel materials will be supplied with (2) hex nuts in place of a knurl nut. Order By: Part number and pipe size
Pipe Hangers
** Note: For metric hanger rod sizes add the metric rod size to the figure number. Example: 200M8-11/2 or 200M10-11/2
Fig. 200 Fig. 200C
Pipe Size
Rod Size
Part No.
in.
(mm)
in.
200-1/2 200-3/4 200-1 200-11/4 200-11/2 200-2 200-21/2 200-3 200-31/2 200-4 200-5 200-6 200-8
1/2"
(15)
3/8"-16
3/4"
(20)
3/8"-16
1" 11/4" 11/2" 2" 21/2" 3" 1 3 /2" 4" 5" 6" 8"
(25)
3/8"-16
(32)
3/8"-16
(40)
3/8"-16
(50)
3/8"-16
(65)
3/8"-16
(75)
3/8"-16
(90)
3/8"-16
(100)
3/8"-16
(125)
1/2"-13
(150)
1/2"-13
(200)
1/2"-13
mm**
M8 or M10 M8 or M10 M8 or M10 M8 or M10 M8 or M10 M8 or M10 M10 M10 M10 M10 M12 M12 M12
Fig. 200F
A
B
Max. Rec. Load
Approx. Wt./100
in.
(mm)
in.
(mm)
lbs.
(kN)
lbs.
(kg)
31/8" 31/8" 33/8" 33/4" 37/8" 41/2" 55/8" 57/8" 73/8" 73/8" 91/8" 101/8" 131/8"
(79.4)
25/8" 21/2" 25/8" 27/8" 27/8" 3" 41/8" 4" 1 5 /4" 5" 61/4" 63/4" 83/4"
(66.7)
400 400 400 400 400 400 600 600 600 1000 1250 1250 1250
(1.78)
11 11 12 13 14 15 27 29 34 35 66 73 136
(5.0)
(79.4) (85.7) (94.0) (98.4) (114.3) (142.9) (149.1) (187.3) (187.3) (231.8) (257.2) (333.4)
(63.5) (66.7) (73.0) (73.0) (76.3) (104.7) (101.6) (133.3) (127.0) (158.7) (171.4) (222.2)
(1.78) (1.78) (1.78) (1.78) (1.78) (2.67) (2.67) (2.67) (4.45) (5.56) (5.56) (5.56)
(5.0) (5.5) (5.9) (6.4) (6.9) (12.3) (13.3) (15.6) (16.0) (30.2) (33.4) (62.3)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
61
Pipe Hangers & Supports
Pipe Hangers Fig. 200H - Heavy Duty Band Hanger (For Trapeze) Size Range: 2” (50mm) thru 4” (100mm) trapeze pipe size. Material: Steel — Pre-Galvanized to G40 Spec Function: Designed primarily to support substantially heavier loads than is normally intended for the nominal hanger size. Used extensively to support trapeze installations and the increased loads from both above and below the trapeze assembly. Features: Furnished with 3/8"-16 or 1/2"-13 adjusting threaded ring nut. B
Approvals: Underwriters Laboratories listed in the USA (UL) and Canada** (cUL). Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 10 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 10.
A
Maximum Temperature: 650°F (343°C) Finish: Pre-Galvanized Order By: Part number, pipe size and rod size.
Pipe Hangers
Important Design Note. Because of the increased loads applied to the trapeze assembly, both the upper trapeze supports as well as the lower hanging unit must be able to hold the maximum loads intended.
Pipe Size Part No. 200H-2-3/8 200H-2-1/2 200H-21/2-3/8 200H-21/2-1/2 200H-3-3/8 200H-3-1/2 200H-4-3/8 200H-4-1/2
Rod Size
in.
(mm)
2" 2" 1 2 /2" 21/2" 3" 3" 4" 4"
(50)
3/8"-16
(50)
1/2"-13
(65)
3/8"-16
(65)
1/2"-13
(75)
3/8"-16
(75)
1/2"-13
(100)
3/8"-16
(100)
1/2"-13
A
B
Max. Rec. Load
Approx. Wt./100
in.
(mm)
in.
(mm)
lbs.
(kN)
lbs.
(kg)
49/16" 423/32" 55/16" 515/32" 53/4" 57/8" 67/8" 71/32"
(115.9)
37/32" 33/8" 323/32" 37/8" 327/32" 331/32" 47/16" 419/32"
(81.7)
1200 1200 1200 1200 1200 1200 1200 1200
(5.34)
48 45 59 56 63 60 76 73
(21.8)
(119.8) (134.9) (138.9) (146.0) (148.1) (174.6) (178.6)
(85.7) (94.4) (98.3) (97.6) (100.8) (112.7) (1116.7)
(5.34) (5.34) (5.34) (5.34) (5.34) (5.34) (5.34)
(20.4) (26.7) (25.4) (28.6) (27.2) (34.5) (33.1)
* Select trapeze pipe size based on section modulus required for span of trapeze per information provided in NFPA 13 (2002) Table 9.1.1.6.1 (a and b). ** All sizes are UL Listed to support up to 8" pipe at max spacing per NFPA 13. For 6” (150mm) and 8” (200mm) trapeze pipe, consult factory.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
62
Pipe Hangers B3198H - Hinged Extension Split Pipe Clamp (TOLCO Fig. 302) A (Rod Size) Hanger Rod Not Included
Size Range: 3/8” (10mm) to 3” (80mm) pipe Material: Malleable Iron
C
Function: Designed for suspending non-insulated pipe horizontally or vertically. Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 25 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 12. Standard Finish: Plain or Electro-Galvanized Order By: Part number and finish.
in.
Pipe Size (mm)
Rod Size A
in.
(mm)
Lbs.
kN
Lbs.
kg
B3198H-3/8
3/8"
(10)
3/8"-16
31/32"
(24.6)
180
(.80)
9
(4.1)
B3198H-1/2
1/2"
(15)
3/8"-16
11/16"
(27.0)
180
(.80)
12
(5.4)
B3198H-3/4
3/4"
(20)
3/8"-16
17/32"
(30.9)
180
(.80)
12
(5.4)
1"
(25)
3/8"-16
111/32"
(34.1)
180
(.80)
13
(5.9)
(32)
3/8"-16
119/32"
(39.7)
180
(.80)
18
(8.1)
(40)
3/8"-16
123/32"
(43.6)
180
(.80)
21
(9.5)
(50)
3/8"-16
2"
(50.8)
180
(.80)
44
(19.9)
(65)
1/2"-13
211/32"
(59.5)
300
(1.33)
73
(33.1)
(80)
1/2"-13
223/32"
(69.0)
300
(1.33)
95
(43.1)
Part No.
B3198H-1 B3198H-11/4
11/4"
B3198H-11/2
11/2"
B3198H-2
2"
B3198H-21/2
21/2"
B3198H-3
3"
C
Design Load
Approx. Wt./100
B3198R - Extension Split Pipe Clamp Size Range: 3/8” (10mm) to 4” (100mm) pipe
C
A (Thread Size) Hanger Rod Not Included
Pipe Hangers
Material: Malleable Iron Function: Designed for suspending non-insulated pipe horizontally or vertically. Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 25 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 12. Standard Finish: Plain or Electro-Galvanized. Contact B-Line for alternative finishes and materials. Order By: Part number and finish.
Part No. Rod Thread
(mm)
Rod Thread Size A
in.
(mm)
Lbs.
(kN)
Lbs.
(kg)
31/32"
Pipe Size in.
C
Design Load
Approx. Wt./100
B3198R-3/8
3/8"
(10)
3/8"-16
(24.6)
180
(.80)
12
(5.4)
B3198R-1/2
1/2"
(15)
3/8"-16
11/16"
(27.0)
180
(.80)
16
(7.2)
B3198R-3/4
3/4"
(20)
3/8"-16
17/32"
(30.9)
180
(.80)
18
(8.1)
1"
(25)
3/8"-16
111/32"
(34.1)
180
(.80)
24
(10.9)
B3198R-11/4
11/4"
(32)
3/8"-16
119/32"
(39.7)
180
(.80)
29
(13.1)
B3198R-11/2
11/2"
(40)
3/8"-16
123/32"
(43.6)
180
(.80)
32
(14.5)
(50)
3/8"-16
2"
(50.8)
180
(.80)
39
(17.7)
(65)
1/2"-13
211/32"
(59.5)
300
(1.33)
115
(52.1)
223/32"
(69.0)
300
(1.33)
140
(63.5)
311/32"
(84.9)
300
(1.33)
160
(72.6)
B3198R-1
B3198R-2 B3198R-21/2
2" 21/2"
B3198R-3
3"
(80)
1/2"-13
B3198R-4
4"
(100)
1/2"-13
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
63
Pipe Hangers & Supports
Pipe Hangers B3198HCT - Hinged Extension Split Pipe Clamp (TOLCO Fig. 301CT) Size Range: 1/2” (15mm) to 2” (50mm) copper tubing A (Rod Size) Hanger Rod Not Included
Material: Malleable Iron Function: A rigid support to suspend tubing horizontally or vertically.
C
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 25 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 12. Standard Finish: DURA-COPPER™ Order By: Part number and finish.
Tubing Size in.
(mm)
Rod Size A
in.
(mm)
Lbs.
(kN)
Lbs.
(kg)
B3198HCT-1/2
1/2"
(15)
3/8"-16
5/8"
(15.9)
180
(.80)
8
(3.6)
B3198HCT-3/4
3/4"
(20)
3/8"-16
13/16"
(20.6)
180
(.80)
10
(4.5)
(25)
3/8"-16
15/16"
(23.8)
180
(.80)
10
(4.5)
(32)
3/8"-16
11/8"
(28.6)
180
(.80)
14
(6.3)
(40)
3/8"-16
19/16"
(39.7)
180
(.80)
18
(8.1)
(50)
3/8"-16
17/8"
(47.6)
180
(.80)
23
(10.4)
Part No.
B3198HCT-1
1"
B3198HCT-11/4
11/4"
B3198HCT-11/2
11/2"
B3198HCT-2
2"
C
Design Load
Approx. Wt./100
Size Range: 1/2” (15mm) to 2” (50mm) copper tubing Material: Malleable Iron
C
Function: A rigid support to suspend tubing horizontally or vertically. Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 25 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 12. Standard Finish: DURA-COPPER™ Order By: Part number and finish.
Tubing Size Part No.
in.
B3198RCT-3/8
3/8"
B3198RCT-1/2
1/2"
B3198RCT-3/4
3/4"
Rod Size A
in.
(mm)
Lbs.
(kN)
Lbs.
(kg)
(10)
3/8"-16
11/16"
(17.5)
180
(.80)
12
(5.4)
(15)
3/8"-16
111/16"
(17.5)
180
(.80)
12
(5.4)
(20)
3/8"-16
7/8"
(22.2)
180
(.80)
14
(6.3)
11/16"
(7.7)
(mm)
C
Design Load
Approx. Wt./100
(25)
3/8"-16
(27.0)
180
(.80)
17
B3198RCT-11/4
11/4"
(32)
3/8"-16
11/8"
(28.6)
180
(.80)
17
(7.7)
B3198RCT-11/2
11/2"
(40)
3/8"-16
15/16"
(33.3)
180
(.80)
22
(10.0)
2"
(50)
3/8"-16
11/2"
(38.1)
180
(.80)
26
(11.8)
B3198RCT-1
B3198RCT-2
1"
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
64
A (Thread Size) Hanger Rod Not Included
Pipe Hangers
B3198RCT - Extension Split Pipe Clamp
Pipe Hangers B3175 - Ring and Bolt Hanger
Bolt and Nut Included Bolt Size
Size Range: 1/2” (15mm) to 6” (150mm) pipe Steel Size
Material: Pre-Galvanized Steel Function: Designed for suspending light-weight non-insulated pipe. (Use with B3222 eye socket or B3224 hanger adjuster).
C
Standard Finish: Pre-Galvanized Order By: Part number and finish. Pipe Size Part No.
in.
C
(mm)
in.
Steel Size (mm)
Bolt Size
18 Ga. x
in.
Design Load
Approx. Wt./100
(mm)
Lbs.
(kN)
Lbs.
(kg)
7/8"
B3175-1/2
1/2"
(15)
11/16"
(27.0)
1/4"-20
(1.2 x 22.2)
275
(1.22)
7.5
(3.4)
B3175-3/4
3/4"
(20)
13/16"
(30.2)
1/4"-20
18 Ga. x 7/8"
(1.2 x 22.2)
275
(1.22)
8.0
(3.6)
1"
(25)
15/16"
(33.3)
1/4"-20
18 Ga. x 7/8"
(1.2 x 22.2)
275
(1.22)
9.0
(4.1)
B3175-11/4
11/4"
(32)
11/2"
(38.1)
1/4"-20
18 Ga. x 7/8"
(1.2 x 22.2)
275
(1.22)
10.5
(4.7)
B3175-11/2
11/2"
(40)
15/8"
(41.3)
1/4"-20
18 Ga. x
7/8"
(1.2 x 22.2)
275
(1.22)
11.5
(5.2)
B3175-1
B3175-2
(50)
113/16"
(46.0)
1/4"-20
18 Ga. x
7/8"
(1.2 x 22.2)
275
(1.22)
13.0
(5.9)
21/2"
(65)
25/16"
(58.7)
5/16"-18
16 Ga. x
11/4"
(1.5 x 31.7)
500
(2.22)
30.0
(13.6)
3"
(80)
25/8"
(66.7)
5/16"-18
16 Ga. x 11/4"
(1.5 x 31.7)
500
(2.22)
35.0
(15.9)
31/2"
(90)
27/8"
(73.0)
5/16"-18
16 Ga. x 11/4"
(1.5 x 31.7)
500
(2.22)
38.5
(17.4)
4"
(100)
31/8"
(79.4)
5/16"-18
16 Ga. x 11/4"
(1.5 x 31.7)
500
(2.22)
42.0
(19.0)
(125)
35/8"
(92.1)
5/16"-18
16 Ga. x
11/4"
(1.5 x 31.7)
500
(2.22)
51.0
(23.1)
(150)
43/16"
(106.4)
5/16"-18
16 Ga. x
11/4"
(1.5 x 31.7)
500
(2.22)
58.5
(26.5)
2"
B3175-21/2 B3175-3 B3175-31/2 B3175-4 B3175-5
5"
B3175-6
6"
B3175CT - Ring and Bolt Hanger, DURA-COPPER™ Coated Pipe Hangers
Bolt and Nut Included
Size Range:
1/2” (15mm)
Bolt Size
to 4” (100mm) pipe
Steel Size
Material: Pre-Galvanized Steel Function: Designed for suspending copper tubing allowing for vertical adjustment. (Use with B3222 eye socket or B3224 hanger adjuster).
C
Standard Finish: DURA-COPPER™ Order By: Part number and finish.
Tubing Size Part No.
C
Steel Size Bolt Size
(mm)
in.
(mm)
B3175CT-1/2
1/2"
(15)
15/16"
(33.3)
1/4"-20
x 1"
1/16"
x 7/8"
(1.6 x 22.2)
B3175CT-3/4
3/4"
(20)
13/8"
(34.9)
1/4"-20
x 1"
1/16"
x 7/8"
(25)
13/16"
(30.2)
1/4"-20
x 1"
1/16"
x
7/8"
(32)
15/16"
(33.3)
1/4"-20
x 1"
1/16"
x
7/8"
(40)
11/2"
(38.1)
1/4"-20
x 1"
1/16"
x
7/8"
x
7/8"
B3175CT-1
1"
B3175CT-11/4
11/4"
B3175CT-11/2
11/2"
B3175CT-2 B3175CT-21/2 B3175CT-3 B3175CT-31/2 B3175CT-4
in.
Design Load
in.
(mm)
Lbs.
Approx. Wt./100
(kN)
Lbs.
(kg)
200
(.89)
8
(3.6)
(1.6 x 22.2)
200
(.89)
8
(3.6)
(1.6 x 22.2)
200
(.89)
8
(3.6)
(1.6 x 22.2)
200
(.89)
10
(4.5)
(1.6 x 22.2)
200
(.89)
11
(5.0)
2"
(50)
115/16"
(49.2)
1/4"-20
x 1"
1/16"
(1.6 x 22.2)
200
(.89)
11
(5.0)
21/2"
(65)
23/16"
(55.6)
1/4"-20
x 1"
1/16"
x 7/8"
(1.6 x 22.2)
200
(.89)
12
(5.4)
3"
(80)
211/16"
(68.3)
1/4"-20
x 1"
1/16"
x 7/8"
(1.6 x 22.2)
200
(.89)
14
(6.3)
(90)
215/16"
(74.6)
1/4"-20
x 1"
1/16"
x
7/8"
(1.6 x 22.2)
200
(.89)
16
(7.2)
(100)
33/16"
(81.0)
1/4"-20
x 1"
1/16"
x
7/8"
(1.6 x 22.2)
200
(.89)
18
(8.1)
31/2" 4"
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
65
Pipe Hangers & Supports
Pipe Hangers B3190 Return Line Offset J-Hook (TOLCO Fig. 40) Size Range: 1/2” (15mm) to 8” (200mm) pipe Material: Steel (Stainless steel available) Function: Recommended for supporting light pipe runs with a 1" (25.4) offset from mounting surfaces. Standard Finish: Plain or Electro-Galvanized. Contact B-Line for alternative finishes and materials. Order By: Part number and finish. Pipe Size Part No.
Design Load
Approx. Wt./100
in.
(mm)
Lbs.
(kN)
Lbs.
(kg)
B3190-1/2
1/2"
(15)
200
(.89)
54
(24.5)
B3190-3/4
3/4"
(20)
200
(.89)
55
(24.9)
B3190-1
1"
(25)
200
(.89)
78
(35.4)
B3190-11/4
11/4"
(32)
200
(.89)
85
(38.5)
B3190-11/2
11/2"
(40)
200
(.89)
90
(40.8)
B3190-2
2"
(50)
200
(.89)
98
(44.4)
(65)
350
(1.55)
126
(57.1)
3"
(80)
350
(1.55)
136
(61.7)
31/2"
(90)
350
(1.55)
147
(66.8)
B3190-4
4"
(100)
450
(2.00)
235
(106.6)
B3190-5
5"
(125)
450
(2.00)
350
(158.7)
B3190-6
6"
(150)
450
(2.00)
383
(173.7)
B3190-8
8"
(200)
450
(2.00)
605
(274.4)
B3190-3 B3190-31/2
9/16"
Dia.
(14.3)
5"
21/2"
B3190-21/2
1" (25.4)
(127.0)
Pipe Hangers
B3191 Return Line Straight J-Hook (TOLCO Fig. 41) Size Range: 1/2” (15mm) to 8” (200mm) pipe Material: Steel (Stainless steel available) Function: Recommended for supporting light pipe runs flush with the mounting surfaces. Standard Finish: Plain or Electro-Galvanized. Contact B-Line for alternative finishes and materials. Order By: Part number and finish. 9/16"
Pipe Size
Design Load
Approx. Wt./100
Part No.
in.
(mm)
Lbs.
(kN)
Lbs.
(kg)
B3191-1/2
1/2"
(15)
200
(.89)
54
(24.5)
B3191-3/4
3/4"
(20)
200
(.89)
55
(24.9)
1"
(25)
200
(.89)
76
(34.5)
B3191-1
11/4"
(32)
200
(.89)
82
(37.2)
B3191-11/2
11/2"
(40)
200
(.89)
87
(39.4)
2"
(50)
200
(.89)
96
(43.5)
21/2"
(65)
350
(1.55)
124
(56.2)
3"
(80)
350
(1.55)
134
(60.8)
31/2"
(90)
350
(1.55)
145
(65.8)
B3191-4
4"
(100)
450
(2.00)
153
(69.4)
B3191-5
5"
(125)
450
(2.00)
348
(157.8)
B3191-6
6"
(150)
450
(2.00)
381
(172.8)
B3191-8
8"
(200)
450
(2.00)
600
(272.1)
B3191-2 B3191-21/2 B3191-3 B3191-31/2
5" (127.0)
B3191-11/4
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
66
Dia.
(14.3)
Pipe Hangers Fig. 120RWA - (Model B) Retrofit Wrap Around “U” Hanger Clamp Size Range: 1" (25mm) thru 6" (150mm) pipe
Component of State of California OSHPD Approved Seismic Restraints System
Material: Steel Function: Designed to restrain movement of the pipe within standard U-hangers as required by NFPA 13. Where retrofit capability is crucial, the Fig. 120RWA is a labor efficient alternative to the standard Cooper B-Line Fig. 120W wrap around U-hanger. Features Installs easily by tightening two hex nuts. Features a unique bracing slot that locks onto a standard U-hanger to become a solid unit that will stabilize the pipe during seismic activity or sprinkler head activation. Designed to be used in retrofit or new construction applications. Will clamp to existing U-Hangers without restriction to leg angle. Approvals: Underwriters Laboratories listed in the USA (UL) and Canada (cUL) as a restrainer. Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to the Cooper B-Line Seismic Restraint Systems Guidelines. NFPA 13 (2010) 9.3.6.3. Finish: Plain and Galvanized. Contact B-Line for alternative finishes and materials. Order By: Part number, type numbers and pipe size Ordering Note: Order by the following type and pipe size: Type 1 — (1" (25mm) and 11/4" (32mm) pipe size) Type 2 — (11/2" (40mm) and 2" (50mm) pipe size) Type 3 — (21/2" (65mm) and 3" (80mm) pipe size) Type 4 — (4" (100mm) pipe size) Type 6 — (5" (125mm) and 6" (150mm) pipe size) Pipe Hangers
Important Note: The bracing slot feature is sized to fit the U-Hanger rod schedule as required by NFPA 13 as follows: 5/16" (7.9mm) rod for up to 2" (50mm) pipe 3/8" (9.5mm) rod for 21/2" (65mm) - 6" (160mm)
pipe For other rod size requirements consult factory.
Type Part No. 120RWA-TYPE1-1
Pipe Size in.
(mm)
1
1"
(20)
120RWA-TYPE1-11/4
1
11/4"
(25)
120RWA-TYPE2-11/2 120RWA-TYPE2-2
2 2
11/2" 2"
(40)
3 3
21/2"
(65)
3"
(80)
4 4 6 6
31/2"
(90)
4" 5" 6"
(100)
120RWA-TYPE3-21/2 120RWA-TYPE3-3 120RWA-TYPE4-31/2 120RWA-TYPE4-4 120RWA-TYPE6-5 120RWA-TYPE6-6
(50)
(125) (150)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
67
Pipe Hangers & Supports
Pipe Hangers Fig. 120 - “U” Hanger Size Range: Size 3/4" (20mm) thru 8" (200mm) pipe Material: Steel Function: Used to support piping from wood beams where no contraction is expected. Used extensively in automatic fire sprinkler systems.
A
Approvals: Meets or exceeds the requirements of National Fire Protection Association (NFPA), Pamphlet 13. Included in our Seismic Restraints Catalog approved by the State of California Office of Statewide Health Planning and Development (OSHPD). For additional load, spacing and placement information relating to OSHPD projects, please refer to the Seismic Restraint Systems Guidelines.
Length (Specify)
Maximum Temperature: 750°F (399°C) Finish: Plain. Contact B-Line for alternative finishes and materials.
Pipe Size Part No. 120-3/4 120-1
A
Fastener Size
in.
(mm)
in.
(mm)
3/4"
(20)
5/16"
(7.9)
(25)
5/16"
1"
Max. Rec. Load*** lbs.
(kN)
16 x 2*
250
(1.11)
(7.9)
16 x 2*
250
(1.11)
120-11/4
11/4"
(32)
5/16"
(7.9)
16 x 2*
250
(1.11)
120-11/2
11/2"
(40)
5/16"
(7.9)
16 x 2*
250
(1.11)
2"
(50)
5/16"
(7.9)
16 x 2*
250
(1.11)
21/2"
(65)
3/8"
(9.5)
3/8
x 21/2**
320
(1.42)
(80)
3/8"
(9.5)
3/8
x
21/2**
320
(1.42)
(90)
3/8"
(9.5)
3/8
x
21/2**
560
(2.49)
(100)
3/8"
(9.5)
1/2
x 3**
560
(2.49)
(12.7)
1/2
x 3**
560
(2.49)
120-2 120-21/2 120-3 120-31/2 120-4
3" 31/2" 4"
Pipe Hangers
Order By: Part number, pipe size, length and finish
120-5
5"
(125)
1/2"
120-6
6"
(150)
1/2"
(12.7)
1/2
x 3**
760
(3.38)
120-8
8"
(200)
1/2"
(12.7)
5/8
x 3**
--
(--)
* Drive Screw ** Lag Bolt *** With minimum safety factor of 5 Fastener schedule per NFPA
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
68
Pipe Hangers Fig. 120MJ - Mutt & Jeff “U” Hanger Size Range: Size 3/4" (20mm) thru 8" (200mm) pipe Material: Steel Function: Used to support piping from wood beams where no contraction is expected. Used extensively in automatic fire sprinkler systems. Fig. 120MJ is used when the wood beam is on a diagonal.
A
Finish: Plain. Contact B-Line for alternative finishes and materials. Length (Specify)
Order By: Part number, side length and finish Pipe Size Part No.
in.
A
Fastener Size
(mm)
in.
(mm)
(7.9)
120MJ-3/4
3/4"
(20)
5/16"
120MJ-1 120MJ-11/4 120MJ-11/2 120MJ-2 120MJ-21/2 120MJ-3 120MJ-31/2 120MJ-4 120MJ-5 120MJ-6 120MJ-8
1" 11/4" 11/2" 2" 21/2" 3" 31/2" 4" 5" 6" 8"
(25)
5/16"
(7.9)
(32)
5/16"
(7.9)
(40)
5/16"
(7.9)
(50)
5/16"
(7.9)
(65)
3/8"
(9.5)
(80)
3/8"
(9.5)
(90)
3/8"
(9.5)
(100)
3/8"
(9.5)
(125)
1/2"
(12.7)
(150)
1/2"
(12.7)
(200)
1/2"
(12.7)
16 x 2* 16 x 2* 16 x 2* 16 x 2* 16 x 2* 3/8 x 21/2** 3/8 x 21/2** 3/8 x 21/2** 1/2 x 3** 1/2 x 3** 1/2 x 3** 5/8 x 3**
Max. Rec. Load*** lbs.
(kN)
250 250 250 250 250 320 320 560 560 560 760 --
(1.11) (1.11) (1.11) (1.11) (1.11) (1.42) (1.42) (2.49) (2.49) (2.49) (3.38) (--)
* Drive Screw ** Lag Bolt *** With minimum safety factor of 5 Fastener schedule per NFPA
Pipe Hangers
Fig. 120W - Wrap Around “U” Hanger Size Range: Size 3/4" (20mm) thru 2" (50mm) pipe Material: Steel Function: Required for automatic fire protection agencies to be used on the end of branch lines to prevent pipe from whipping vertical and striking ceiling or beam.
A
Finish: Plain. Contact B-Line for alternative finishes and materials. Order By: Part number, side length and finish
Length (Specify)
Pipe Size Part No.
in.
A
Fastener Size
(mm)
in.
(mm)
(7.9)
120W-3/4
3/4"
(20)
5/16"
120W-1 120W-11/4 120W-11/2 120W-2
1" 1 1 /4" 11/2" 2"
(25)
5/16"
(7.9)
(32)
5/16"
(7.9)
(40)
5/16"
(7.9)
(50)
5/16"
(7.9)
16 x 2* 16 x 2* 16 x 2* 16 x 2* 16 x 2*
Max. Rec. Load*** lbs.
(kN)
250 250 250 250 250
(1.11) (1.11) (1.11) (1.11) (1.11)
* Drive Screw *** With minimum safety factor of 5 Fastener schedule per NFPA
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
69
Pipe Hangers & Supports
Pipe Hangers A (Rod Size)
B3262 Light Duty Spring Hanger Rod Size Range: 3/8”-16 to 3/4”-10
C
Material: Steel Service: Designed for use with a light piping system where vertical movement does not exceed 11/4" (31.7). D
Approvals: Conforms to Federal Specification WW-H-171E & A-A-1192A, Type 49 and Manufacturers Standardization Society ANSI/MSS SP-69 & SP-58, Type 48. Order By: Part number.
B A (Rod Size)
Spring Color
In
B (mm)
B3262-3/8
3/8"-16
Brown
2"
B3262-1/2
1/2"-13
B3262-5/8
5/8"-11
Red
B3262-3/4
3/4"-10
Orange
Black
C (mm)
In
(mm)
(50.8)
23/4"
(69.8)
41/2"
(114.3)
(50.8)
23/4"
(69.8)
41/2"
(114.3)
2"
(50.8)
23/4"
(69.8)
41/2"
(114.3)
2"
(50.8)
3"
(76.2)
7"
(177.8)
2"
Spring Deflection
Rated Load
Part No.
In
(mm)
Lbs.
B3262-3/8
1.20
(30.1)
B3262-1/2
1.10
(27.7)
B3262-5/8
1.00
B3262-3/4
1.20
D
In
Approx. Wt./100
(kN)
Lbs.
(kg)
100-150
(.44 - .67)
390
(176.2)
150-250
(.67 - 1.11)
410
(186.0)
(25.4)
350-450
(1.56 - 2.00)
470
(213.2)
(30.1)
600-750
(2.67 - 3.34)
1240
(562.6)
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
70
Pipe Hangers
Rod Size A
Part No.
Pipe Hangers BH-2-4, BH-5-8, BH-9-12 - Parallel Strap Hangers BH-2-4-R, BH-5-8-R, BH-9-12-R - Right Angle Strap Hangers Material: Steel Function: The Parallel Strap Hanger series is designed for suspending up to 1" (50.8) wide straps parallel to beams. The Right Angle Strap Hanger series is designed for suspending up to 1" (50.8) wide straps at right angle to the beam. Note: Install clip to beam with hammer. Standard Finish: Zinc Phosphate Order By: Part number and finish.
Part No. Parallel Right Angle BH-2-4 BH-5-8 BH-9-12
Right Angle Strap
Parallel Strap
Flange Thickness In.
BH-2-4-R
1/8"
BH-5-8-R
5/16"
BH-9-12-R
9/16"
Approx. Wt./100 BH-2-12 BH-2-12R
Maximum Load
(mm)
Lbs.
(kN)
Lbs.
to
1/4"
(kg)
Lbs.
(kg)
(3.2 to 6.3)
200
(.89)
4.5
(2.0)
6.0
(2.7)
to
1/2"
(7.9 to 12.7)
200
(.89)
5.0
(2.3)
6.5
(2.9)
to
3/4"
(14.3 to 19.0)
200
(.89)
5.5
(2.5)
7.0
(3.2)
Design Load is a static straight down load.
BL1400 - Hanger Size Range:
W
1/2” (15mm)
to 4” (100mm) pipe
Pipe Hangers
Material: Steel
Pipe Size T
Function: Designed to support or suspend light duty stationary pipe runs.
A
Standard Finish: Electro-Galvanized Order By: Part number.
Hole Size B
Pipe Size Part No.
A
B
T
W
Approx. Wt./100
In.
(mm)
In.
(mm)
In.
(mm)
In.
(mm)
In.
(mm)
Lbs.
(kg)
BL1400
1/2"
(15)
29/32"
(23.0)
9/32"
(7.1)
16 Ga.
(1.5)
3/4"
(19.0)
6
(2.7)
BL1410
3/4"
(20)
31/32"
(24.6)
9/32"
(7.1)
16 Ga.
(1.5)
3/4"
(19.0)
7
(3.2)
BL1420
1"
(25)
11/4"
(31.7)
9/32"
(7.1)
16 Ga.
(1.5)
3/4"
(19.0)
8
(3.6)
BL1430
11/4"
(32)
113/32"
(35.7)
9/32"
(7.1)
18 Ga.
(1.5)
7/8"
(22.2)
10
(4.5)
BL1440
11/2"
40)
55/8"
(41.3)
11/32"
(8.7)
16 Ga.
(1.5)
1"
(25.4)
17
(7.7)
BL1450
2"
(50)
17/8"
(47.6)
11/32"
(8.7)
16 Ga.
(1.5)
11/4"
(31.7)
25
(11.3)
BL1460
21/2"
(65)
21/16"
(52.4)
11/32"
(8.7)
16 Ga.
(1.5)
11/4"
(31.7)
26
(11.8)
BL1470
3"
(80)
21/2"
(63.5)
11/32"
(8.7)
16 Ga.
(1.5)
11/4"
(31.7)
33
(14.9)
BL1480
31/2"
(90)
23/4"
(69.8)
11/32"
(1.5)
11/4"
(31.7)
36
(16.3)
(100)
31/2"
(88.9)
11/32"
(1.5)
11/4"
(31.7)
40
(18.1)
BL1490
4"
(8.7) (8.7)
16 Ga. 16 Ga.
Designed for positioning only, no load rating.
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
71
Pipe Hangers & Supports
Pipe Hangers
Pipe Hangers
All dimensions in charts and on drawings are in inches. Dimensions shown in parentheses are in millimeters unless otherwise specified.
Pipe Hangers & Supports
72
