Transcript
PL-880 QUICK START
TECSUN
FM-stereo / AM / LW / SW / SW SSB radio receiver POWER /
page 18
SNOOZE
Power switch and sleep timer
page 6, 16
To activate the SLEEP TIMER, press and hold the [POWER] button, rotate the [TUNING] knob to adjust the sleep timer (1-120 minutes or " "), press the [POWER] button again to confirm (the " " symbol will show on the display).
Press the [SNOOZE] button when the radio alarm is on. The device will alarm again after 5 minutes.
SLEEP
To power on/off the radio, press the [POWER] button.
page 7
SW, FM TELESCOPIC ANTENNA
LIGHT LCD backlight
Fully extend the antenna and change its direction for better SW/FM reception.
SW ANT.
SW external antenna jack
While operating any keys or knobs, the orange backlight will turn on for about 5 seconds. You can also push the [ON/OFF LIGHT] switch into the ON position to keep the backlight turned on.
page 21
TUNING SW ANT. GAIN
page 18
Multifunction Knob
page 20
SW attenuator step control
Rotate the [TUNING] knob to adjust time, frequency, memory address in the related modes.
Depending on the strength of the radio signal and interference, select DX (far distance) / NORM (standard) / LOCAL (near) location, to get the best reception.
TONE SELECT Stereo headphone jack
Audio tone adjustment
page 20
page 19 Push the [TONE] upward for "TREBLE" listening, downward for "BASS" listening.
Stereo reception is only possible on FM-frequencies.
Power amplifier
FINE TUNING LINE OUT
page 20 FM tuning step 10 KHz AM, SW tuning step 1 KHz Single Side Band tuning step 10 Hz
This device is able to output the signal to an external amplifier or recording device through an audio cable connection. Note: While using the line out function, volume control is performed via the external device.
Audio input jack
Audio line out jack or
VOLUME Volume control knob
ICR-100
page 22
DC power supply is 5V, using USB plug
Rotate the [VOLUME] knob to adjust your desired volume level.
RESET
page 16
TIME SETTING
Reset the device by sticking a pointed object into the reset hole and gently press the [RESET] button.
Press & hold the [TIME] button until the hours indicator flashes, rotate the [TUNING] knob to adjust the hours, press the [TIME] button again to confirm and enter the minutes setting, rotate the [TUNING] knob to adjust the minutes, press the [TIME] button to confirm.
FM ALARM FUNCTION
page 22
page 11
page 17, 18 FM mode: press the [FM] button.
To adjust the alarm setting, press & hold the [ALARM] button until the hours indicator flashes, rotate the [TUNING] knob to adjust the hours, press the [ALARM] button to confirm and enter the minutes setting, rotate the [TUNING] knob to adjust the minutes and press the [ALARM] button again to confirm and enter the "Alarm Off Timer" setting, rotate the [TUNING] knob to select the number of minutes (0-90) after which the radio turns off automatically, press the [ALARM] button to confirm.
ATS (AUTO TUNING STORAGE) mode: Press and hold the [FM] button.
To set the ALARM station, turn on the radio and select your preferred station for the alarm sound, adjust your desired volume level, then press the [MEMORY] button (PRESET will flash on the display), immediately press the [ALARM] button to confirm.
MW/LW mode: Press the [AM] button.
To activate the alarm function, press the [ALARM] button, the " again to deactivate (the " " symbol disappears).
AM (MW/LW)
ATS (AUTO TUNING STORAGE) mode: Press and hold the [AM] button.
" symbol appears on the display, press the [ALARM] button
“
When the alarm goes off, press the [POWER] button twice to stop it.
MEMORY DISPLAY /
Display mode/Lock button
page 20
In radio ON mode, repeat press the [DISPLAY] button to display either ALARM TIME, TIME, or RADIO SIGNAL. Press and hold to activate/deactivate the KEYLOCK function.
FM ST. / AM BW FM stereo/AM bandwidth button
Station storage procedure
page 10
VF (view frequency) / VM (view memory) FUNCTION
” SW/SW Meter Band Selection
ATS (AUTO TUNING STORAGE) In SW mode A: press and hold the [ In SW mode B: press and hold the [ meter band.
Turn on the device, select your desired station, press the [MEMORY] button (PRESET flashes on the display), press it again to store the station into the memory.
] and [
page 12
] button.
] button to ATS for stations within all meter bands ] button to ATS only for stations within the present
page 19
USB/NORM
" symbol appears on the display), press it again to deactivate VF mode: direct press the numeric buttons to input station frequency. VM mode: direct press the numeric buttons to input station memory.
LSB/NORM
page 21
In SW mode, press the [USB/NORM] or [LSB/NORM] button to select either the Upper Side Band (USB) or Lower Side Band (LSB).
page 8
VF: Press the [VF/VM] button. When the station frequency indicator flashes twice, the VF mode is activated, press and hold the [VF/VM] button until the frequency starts running to auto browse all stations, staying on each station for about 5 seconds. Press the [MEMORY] button to store your desired station into the memory. VM: Press the [VF/VM] button. When the station memory indicator in the top right corner of the display flashes, the VM mode is activated. Press and hold the [VF/VM] button until PRESET flashes on the display, the device will auto browse all stored stations, staying on each station for about 5 seconds. To delete a stored station, press the [DELETE] button. To stop browsing, rotate the [TUNING] knob or press the [VF/VM] button.
FEATURES
”“
SW / SW Meter Band mode: press the [
0-9 Numeric button Press the [FM ST.] button to activate the stereo function (the " (the " " symbol disappears).
page 11
DELETE
Delete programed station procedure
page 14, 15
PAGE
MEMORY PAGE
page 12
Press the [page + / -] button to select your desired memory page.
In VM mode, rotate the [TUNING] knob to select the stored station which you want to delete, then press and hold the [DELETE] button ( " " flashes on the display), press the [DELETE] button again to remove the station from memory.
SYSTEM SETTING (In Power Off Mode) FM FREQUENCY RANGE Press & hold the [FM SET] button until 88-108MHz, 76-108MHz or 87-108MHz appears on the display. Press the [FM SET] button to select a suitable frequency range for FM. TURN ON/OFF LW To turn ON/OFF LW, press & hold the [AM] button until "LW ON" or "LW OFF" appears on the display. MW (AM) 9K/10K TUNING STEPS To select your desired AM tuning steps, press & hold the [9/10kHz] button until "9kHz" or "10kHz" appears on the display.
AUTO-SORTING STATION LIST In POWER OFF mode, to automatically sort all stored station memories, press & hold the [ ] button for about 2 seconds until the memory page number in the upper right corner starts running. This function is able to: 1. Remove all duplicate stations. Especially useful after storing stations manually, as you may sometimes store a station more than once. 2. Auto-sorting the sequence of stored stations. - In page P0, select your desired band to find all stored stations in sequence of frequency (from low to high). - In page P01-24, all stored stations are placed in sequence of frequency (from low to high), and in sequence of FM, SW, MW, LW.
