Transcript
Platform # 07
Firmware: PKN3
Installation Manual (1/5 pages)
Description: Nissan Infiniti CAN BUS Data Immobilizer Override (NO KEY REQUIRED) Functions: Data Transponder Interface: Override OEM Transponder Immobilizer Via Data Downloadable Firmware for Platform #07: PKN3 WARNING: Before beginning your install go to www.XpressDownload.com and be sure to print the LATEST corresponding installation manual for the firmware that is flashed to the platform you are using.
PUSH TO START 2007 NISSAN ALTIMA SUPPLEMENT INSTALLATION MANUAL
IMPORTANT! Ensure that the neutral safety relay is installed on this vehicle. It prevents the vehicle from being remote started in gear and lurching forward, causing damage or injury. The wire colors sometimes differ from model to model than what is specified in the installation guide. Please use the specific pin locations when making these connections instead of relying on the wire colors. ALWAYS TEST THE INSTALLATION ONCE A RELAY IS INSTALLED, TO ENSURE THE VEHICLE CANNOT BE STARTED IN GEAR.
IMPORTANT: PLEASE READ THE FULL INSTALLATION MANUAL BEFORE PROCEEDING WITH INSTALL. Some connection will have to be made at the vehicle's FUSEBOX (driver's side) inside the engine compartment. Please follow these instructions carefully to ensure there are no issues during installation. ADDITIONNAL PRODUCT REQUIRED: 1x relay: in order to activate the vehicle start circuit. 2x 1amp diodes: used to isolate Accessory 1 & 2 to ensure no feedback. 1x spade (female) terminal connector. Additional wire (14-16 guage): used to connect to the external circuits (starter, ignition and parking lights) PARKING LIGHTS: ISOLATION OF INDEPENDENT PARKING LIGHTS IS A MUST! The 2007 Altima is equipped with independent left and right parking circuits which must be isolated. Using either 2x 5 amp diodes OR 2 relays will provides isolation. IGNITION #1 CIRCUIT: Located PIN #37 at fusebox. There is no wire at this PIN therefore a spade (female) terminal connector will be required in order to access this circuit. END USER OPERATING INSTRUCTIONS: Once the 2007 Altima is running under remote start, the vehicle's PUSH TO START button will need to be pushed twice before applying the brake. If this procedure is not followed, the vehicle will shut down.
Platform # 07
Firmware: PKN3
Installation Manual (2/5 pages)
Description: Nissan Infiniti CAN BUS Data Immobilizer Override (NO KEY REQUIRED) Functions: Data Transponder Interface: Override OEM Transponder Immobilizer Via Data
INSTALLATION INSTRUCTIONS FOR THE 2007 NISSAN ALTIMA: PUSH-TO-START VEHICLE
Altima 2007 Function
Polarity
Wiring
Battery
Positive
Red 14 Gauge fuse box under hood
Ignition 1
Positive
PIN 37 Empty place, fuse box under hood
Ignition 2
Positive
PIN 13, White wire, fuse box under hood
Ignition 3
Positive
PIN 11, Red/Black wire, at BCM behind cluster
Accessories 1
Positive
PIN 31, Yellow wire, at BCM behind cluster
Accessories 2
Positive
PIN 24, Blue 2 silver dot wire, behind cluster
Accessories 3
Positive
PIN 48, Yellow/Red wire, fuse box under hood
Starter
Positive
PIN 80, Black/White wire, fuse box under hood
Lock
Negative
Blue/Black wire, inside driver door
Unlock
Negative
Blue/Red wire, inside driver door
Arm/Disarm
See Lock and Unlock wires
Door
Negative Negative
Hood
Negative
Add hood contact
Trunk
Negative
Blue/Red wire, at switch in dash. (Unlock doors before open the trunk to disarm)
Parking light
Positive
Pin 92, Light green/Orange wire & Pin 91, Light green/Black wire, fuse box under hood
Handbrake
Negative
Green/Red wire, at handbrake switch
Brake light
Positive
Red/Green wire, at switch pedal
Tach signal
AC
Front left door: Pin 39, Light blue wire, green connector at BCM behind the cluster. Front right door: Pin 13, Red/Black wire, green connector at BCM behind the cluster. Rear left door: Pin 38, Red/Black wire, gray connector at BCM behind the cluster. Rear right door: Pin 37, Red/White wire, gray connector at BCM behind the cluster.
Blue/Black wire, at coil
Horn
Negative
Blue/White wire at steering column
Neutral safety switch
Positive
PIN 30, Yellow wire, under hood
Platform # 07
Firmware: PKN3
Installation Manual (3/5 pages)
Description: Nissan Infiniti CAN BUS Data Immobilizer Override (NO KEY REQUIRED) Functions: Data Transponder Interface: Override OEM Transponder Immobilizer Via Data
INSTALLATION INSTRUCTIONS FOR THE 2007 NISSAN ALTIMA: PUSH-TO-START VEHICLE
The fuse box is under the hood on driver side. Parking light (+)
85
87A Starter ( + )
30
To Black/White
87
86
Add 2 diodes 5A or 2 relays
To Yellow 106 98 105 97 104 96
Ignition 1 (+) : You need to add a wire because this place is empty.
38 36 37 35
82 80 81 79
103 95 102 94 101 93 100 92 99 91
Ignition2 (+): White
34 33 32 31 30
24 23 22 21 20
78 68 77 76 75 74
67 66 65 64
29 28 27 26 25
19 18 17 16 15
73
63
72 71 70 69
62 61 60 59
14 13 12 11 10 9
8 7 6 5 4 3
58 57 56 55 54 53
52 51 50 49 48 47
Batterie (+)
Conenct to 14 gauge red wire in fuse box Accessories 3 Yellow/Red wire
Accessoires (+)
See connection on page 4 for this wire.
Platform # 07
Firmware: PKN3
Installation Manual (4/5 pages)
Description: Nissan Infiniti CAN BUS Data Immobilizer Override (NO KEY REQUIRED) Functions: Data Transponder Interface: Override OEM Transponder Immobilizer Via Data
INSTALLATION INSTRUCTIONS FOR THE 2007 NISSAN ALTIMA: PUSH-TO-START VEHICLE
BCM: Located Behind Cluster
19
24
Pink
Red/Black
Violet Can High
Violet/White Can Low
Ignition 3 (+)
Blue
XK7-PKN3
Acc. 1 Yellow wire
BCM 21 1
30
40 20
B
Pink Cut security led Blue/Orange wire
Pink/White
Pink
Pink/White
M18
D2D
Acc. 2 Blue 2 silver dot
20 40
Diode 1 amp
11 31
M19
Diode 1 amp
1
21
Accessories (+)
Platform # 07
Firmware: PKN3
Installation Manual (5/5 pages)
Description: Nissan Infiniti CAN BUS Data Immobilizer Override (NO KEY REQUIRED) Functions: Data Transponder Interface: Override OEM Transponder Immobilizer Via Data
INSTALLATION INSTRUCTIONS FOR THE 2007 NISSAN ALTIMA: PUSH-TO-START VEHICLE LIMITED ONE-YEAR CONSUMER WARRANTY For a period of ONE YEAR from the date of purchase of a Directed Electronics remote start or security accessory product, Directed Electronics. (hereinafter "DIRECTED") promises to the original purchaser, to repair or replace (at DIRECTED's election) with a comparable reconditioned piece, the security or remote start accessory piece (hereinafter the "Part"), which proves to be defective in workmanship or material under normal use, provided the following conditions are met: the Part was purchased from an authorized DIRECTED dealer in the United States; and the Part is returned to DIRECTED, postage prepaid, along with a clear, legible copy of the receipt or bill of sale bearing the following information: consumer's name, address, telephone number, the authorized licensed dealer's name, date of purchase and complete product and Part description. This warranty is non-transferable and is automatically void if the Part has been modified or used in a manner contrary to its intended purpose or if the Part has been damaged by accident, abuse, unreasonable use, neglect, water, theft, improper service, installation or other causes not arising out of defect in materials or construction. This warranty is automatically void if any Part has had the serial number defaced, altered, or removed. This warranty is automatically void if the Part has had Repair Service performed by anyone other than the Directed Repair Department. This warranty does not cover damage to any Part caused by installation or removal of the Part or any system related thereto. This warranty does not cover labor costs for the removal or reinstallation of the Part. TO THE MAXIMUM EXTENT ALLOWED BY LAW, ALL WARRANTIES, INCLUDING BUT NOT LIMITED TO EXPRESS WARRANTY, IMPLIED WARRANTY, WARRANTY OF MERCHANTABILITY, FITNESS FOR PARTICULAR PURPOSE AND WARRANTY OF NON-INFRINGEMENT OF INTELLECTUAL PROPERTY, ARE EXPRESSLY EXCLUDED TO THE MAXIMUM EXTENT PERMITTED BY LAW; AND DIRECTED NEITHER ASSUMES NOR AUTHORIZES ANY PERSON OR ENTITY TO ASSUME FOR IT ANY DUTY, OBLIGATION OR LIABILITY IN CONNECTION WITH ITS PRODUCTS. DIRECTED HEREBY DISCLAIMS AND HAS ABSOLUTELY NO LIABILITY FOR ANY AND ALL ACTS OF THIRD PARTIES INCLUDING DEALERS OR INSTALLERS. IN THE
This Interface kit / Data Bus Interface part has been tested on the listed vehicles. Other vehicles will be added to the select vehicle list upon completion of compatibility testing. Visit website for latest vehicle application guide. DISCLAIMER: Under no circumstances shall the manufacturer or the distributors of the bypass kit / data bus interface part(s) be held liable for any consequential damages sustained in connection with the part(s) installation. The manufacturer and it’s distributors will not, nor will they authorize any representative or any other individual to assume obligation or liability in relation to the interface kit / data bus interface part(s) other than its replacement. N.B.:Under no circumstances shall the manufacturer and distributors of this product be liable for consequential damages sustained in connection with this product and neither assumes nor authorizes any representative or other person to assume for it any obligation or liability other than the replacement of this product
