Playing A Cd

Transcript

Table of Contents ▼ Main Menu ▲ ０４／０６／２４ １８：４０：５６ ３１Ｓ６Ｍ６３０ ０１０４  Playing a CD All models except Type-S CD/TAPE BUTTON AM/FM BUTTON REPEAT INDICATOR CD SLOT REPEAT BUTTON EJECT BUTTON Features RANDOM INDICATOR POWER/VOLUME KNOB RANDOM BUTTON SEEK/SKIP BAR CD SLOT RANDOM INDICATOR REPEAT INDICATOR Type-S LOAD BUTTON CD EJECT BUTTON POWER/VOLUME KNOB REPEAT BUTTON RANDOM BUTTON SKIP BUTTONS FM BUTTON CD BUTTON AM BUTTON 101 Table of Contents ▼ Main Menu ▲ ０４／０６／２４ １８：４１：０８ ３１Ｓ６Ｍ６３０ ０１０５  Playing a CD CD Player With the ignition in the ACCESSORY (I) or ON (II) position, insert a CD into the CD slot. The drive will pull the CD in the rest of the way and begin to play it. You operate the CD player with the same controls used for the radio. The number of the track playing is shown in the display. The system will continuously play a CD until you change modes. To Change Tracks (SKIP) Each time you press and release / (＋) , the player skips forward to the beginning of the next track. Press and release / ( −) to skip backward to the beginning of the previous track. To move rapidly within a track, press and hold the / (＋) or / (−) . You will see CUE or REW in the display. 102 REPEAT − To continuously replay a track, press and release the RPT button. You will see RPT in the display. Press the RPT button again to turn it off. Type-S only Pressing either of the SKIP buttons also turns off the repeat feature. RANDOM − This feature plays the tracks in random order. To activate Random Play, press and release the RDM button. You will see RDM in the display. This continues until you press the RDM button again. To Stop Playing a CD Press the eject button ( ) to remove the CD. If you eject the CD, but do not remove it from the slot, the system will automatically reload the CD after 15 seconds and put it in pause mode. To begin playing, press the CD button. Press the AM/FM button to switch to the radio while a CD is playing. Press the CD button to play the CD. If you turn the system off while a CD is playing, either with the PWR/VOL knob or by turning off the ignition, the CD will stay in the drive. When you turn the system back on, the CD will begin playing where it left off. Table of Contents ▼ Main Menu ▲ ０４／０６／２４ １８：４１：２３ ３１Ｓ６Ｍ６３０ ０１０６  CD Changer Operating the CD Changer Loading CDs in the Changer Type-S To load multiple CDs in one operation: To load CDs or operate the CD changer, the ignition switch must be in the ACCESSORY (I) or ON (II) position. Load and play only standard round CDs. Odd-shaped CDs may jam in the drive or cause other problems. You cannot load and play 3-inch (8 cm) CDs in this system. Avoid using discs with adhesive labels. The label can curl up and cause the disc to jam in the unit. 1. Press and hold the Load button until you see ‘‘LOAd’’ in the display, then release the button. 2. On the upper left side of the display, the CD number for an empty position will begin blinking and the green CD Loaded indicator will come on. 3. Insert the CD into the CD slot. Insert it only about halfway; the drive will pull it in the rest of the way. You will see ‘‘BUSY’’ in the display. The CD Loaded indicator turns red and blinks as the CD is loaded. If you are not loading CDs into all six positions, press the Load button again after the last CD has loaded. The system will begin playing the last CD loaded. If you stop loading CDs before all six positions are filled, and you do not press the Load button, the system will wait for 10 seconds, then stop the load operation and begin playing the last CD loaded. 4. When LOAd appears again in the display, insert the next CD into the CD slot. CONTINUED 103 Features Your vehicle’s audio system has an in-dash CD changer that holds up to six CDs, providing several hours of continuous entertainment. You operate this CD changer with the same controls used for the radio and tape player. 5. Repeat this until all six positions are loaded. The system will then begin playing the last CD loaded. Table of Contents ▼ Main Menu ▲ ０４／０６／２４ １８：４１：３５ ３１Ｓ６Ｍ６３０ ０１０７  CD Changer To load a single CD: 1. Press and release the Load button. 2. When the CD number for an empty position starts to blink and the green CD Loaded indicator comes on, you will see LOAd in the display. Insert the CD into the CD slot. Insert it only about halfway, the drive will pull it in the rest of the way. 3. The system will load the CD, and begin playing it. If you press the Load button while a CD is playing, the system will stop playing that CD and start the loading sequence. It will then play the CD just loaded. You can also load a CD into an empty position while a CD is playing by pressing the appropriate preset button. Select an empty position (the CD Loaded indicator is off), and press the preset button for that position (1 to 6). The system will stop playing the current CD and start the loading sequence. It will then play the CD just loaded. Operation Select the CD changer by pressing the CD button. You will see ‘‘Cd’’ in the display. The system will begin playing the last selected CD in the CD changer. You will see the CD and track numbers displayed. When that CD ends, the next CD in the CD changer is loaded and played. After the last CD finishes, the system returns to CD 1. To select a different CD, press the appropriate Preset button (1 − 6). If you select an empty position in the CD changer, the system will go into the loading sequence (see page 103 ). You can use the SKIP buttons while a CD is playing to select passages and change tracks. 104