Preview only show first 10 pages with watermark. For full document please download

Plc/ir Transmitter/receiver Dimmer Switch

   EMBED


Share

Transcript

CÉLIANE TECHNICAL GUIDE PLC/IR transmitter/receiver dimmer switch 672 10 672 14 Description These MY HOME Legrand power line communication dimmer switches control the ON/ OFF, dimmer functions, and preset levels of the lighting circuits connected to their clamps: - manually, using the front controls, - using a power line communication, or radio transmitter, through a PLC/RF interface. The dimmer is a receiver. - using a mobile infrared transmitter. The dimmer is an IR receiver. Dimmer switches can be used for remote control of MY HOME Legrand receiver lighting devices. The dimmers are transmitter. A receiver can be operated by up to 32 control transmitters. All MY HOME Legrand products fitted with an infrared cell may transmit through the network a scenario control from a remote infrared transmitter. The status indicator: It indicates the lighting level of the load connected to the dimmer Local operation The dimmer switch controls the light points connected to its clamps: - switching on, pressing the ON key, - switching off, pressing the OFF key, - switching on at 66% brightness level (factory setting), pressing key 1 - switching on at 33% brightness level (factory setting), pressing key 2 - increasing dimmer function, pressing and holding down the ON or the 1 key, - decreasing dimmer function, pressing and holding down the OFF or the 2 key. Note: Switching on occurs within 1 second, switching off within 2 seconds. Customising the brightness level of key 1: Action 1 2 3 4 6 5 4 Legend 1. Load status indicator (blue). For 672 14 2. Infrared cell 3. The 1st LED will turn red if in case of device protection (overload, temperature too high, short circuit or load not connected). For 672 14 4. Control keys: 1 - increasing dimmer function; 2 - decreasing dimmer function; ON - increasing dimmer function; OFF - decreasing dimmer function 5. LEARN LED 6. LEARN key L Dimmer switch: Short pressure of the ON key Related articles Key cover 680 75 and 683 75 (for device 672 10) Key cover 680 76 and 683 76 (for device 672 14) Press and hold down the ON and OFF keys to obtain the desired brightness level Standards, Certification, Marks Press and hold down keys 1 and ON for 5 seconds and then Normalised line socket following EN 50 065-1 Products in accordance with EN 50 065-1, -2.1,-7 and NF EN 60 669-2.1 Customising the brightness level of key 2: Action L Dimmer switch: Dimensional data 2 flush-mounting modules Short pressure on the ON key and then 1 LG00178-a-UK Press and hold down keys 2 and OFF for 5 seconds PLC SYSTEM Press and hold down the ON and OFF keys to obtain the desired brightness level PRODUCT TECHNICAL SHEETS 672 10 672 14 Description Operation as receiver The dimmer switch has a lighting circuit output. It can be operated to perform: 1.ON/OFF functions, by simple or double switches, automatic switches, power line communication controlled sockets. 2.ON/OFF functions, at a preset level, by power line communication, infrared, or radio scenario switches, using the PLC/RF interface, including an automatic radio switch. 3. ON/OFF and dimmer control using: - dimmer switches, remote dimmer switches, power line communication dimmer controlled sockets. - power line communication or radio lighting scenario switches* using the PLC/RF interface * the power line communication lighting scenario switch can also control it at preset level, using keys 1 and 2. 4. ON/OFF dimmer control using the IR 882 00 remote control, by directly pointing the device, as well as using the RF/IR remote control 882 15 Example: Create a dimmer two-way switch using a dimmer switch (672 10) and a lighting scenario switch (672 08) N L Transmitter 672 08 Receiver 672 10 L It is not necessary to program the OFF pushbutton of the *lighting scenario switch, as this is learnt automatically. On the lighting scenario switch: - press the ON key, switch on, - press and hold down the ON key, gradual increase of the brightness level - press the OFF key, switch off, - press and hold down the OFF key, gradual decrease of the brightness level. Note: During the programming procedure, pressing keys 1 and 2 of the dimmer (after pressing Learn), will remove the link between these two keys and the dimmer function (deleting the preset levels). Operation as transmitter The dimmer switch has three control directions: - one ON/OFF and increasing/decreasing dimmer direction, - one scenario 1 and increasing dimmer direction, - one scenario 2 and decreasing dimmer direction. For example, it can control remote switches and other remote dimmer switches. LG00178-a-UK N L Transmitter 672 10 Receiver 672 10 It is not necessary to program the OFF pushbutton of the dimmer switch (transmitter), as this is learnt automatically. On the dimmer switch (transmitter): - press the ON key, switch on, - press and hold down the ON key, gradual increase of the brightness level - press the OFF key, switch off, - press and hold down the OFF key, gradual decrease of the brightness level, decrease of the loads connected to the two dimmers. Example 2 : Controlling a simple switch (672 01) and a dimmer switch (672 10) using key 1 of a dimmer switch (672 10). L N 2 Example 1: Controlling a dimmer switch (672 10) using the ON key of another dimmer switch (672 10) N L Transmitter 672 10 Receiver 672 01 Transmitter 672 10 Key 2 of the dimmer switch (transmitter) does not switch off (short pressure) or decrease the load (extended pressure) of the actuators programmed on key 1 (they are not automatically learnt). On the dimmer switch (transmitter): - pressure of key 1 switches on lamp L1 at 100%, and lamp L2 at the programmed brightness level. - press and hold down key 2, gradual increase of the brightness level of lamp L2. The brightness level of lamp L1 cannot be adjusted. To change the brightness level, it is recommended that the same group of devices are programmed on keys 1 and 2. Note: Using a dimmer set as OFF within the lighting scene, it is possible to change the light level by pressing and holding down 1. CÉLIANE TECHNICAL GUIDE 672 10 672 14 Description Wiring diagram To record a brightness level when performing the scenario learning procedure Step 1: start the learning procedure (on the TRANSMITTER) 1. Press LEARN 2. Press the ON control key that will be associated to leader 3. Press and hold down the ON or OFF keys, to obtain the desired brightness level Note: Never use Pushbuttons 1 and 2 of the Dimmer. N L Technical data 100 – 240 Vac 50 – 60 Hz 8 mm Voltage: Frequency: Consumption: - Idle: - Loaded: Self-extinguishing: Storage and operating temperatures: 0.6 W 1.2 W 30 s @ 650 °C (-5) – (+45) °C 672 10 230 V 110 V 672 14 230 V Halogen lamp TBT halogen lamp with ferromagnetic transformer * Min. 20 W 20 W 20 VA Max. 150 W 150 W 150 VA Min. 20 W 20 W 20 VA Max. 300 W 300 W 300 VA Min. 20 W 20 W 20 VA Max. 300 W 300 W 300 VA Min. 20 W 20 W 20 VA Max. 600 W 600 W 600 VA *Note: The performance of the transformers must be taken into account. For example, for a double switch, the maximum TBT halogen light load for each direction will be 210 W with a transformer with a 70% performance, instead of 300 W. Besides, a transformer must be loaded at 60% of its power. 3 LG00178-a-UK 110 V Incandescent lamp PLC SYSTEM Maximum controlled power: