Transcript
PLCMTR ‐ Commercial Grade Camera System
www.pyleaudio.com
Please read instructions carefully before installation and use. Installation should be performed by a professional installer.
To ensure your safety, the driver should not watch videos or operate features on the monitor while driving. There are no serviceable parts in this unit, do not disassemble or try to repair this unit. If unit malfunctions please return to your vendor or send to a Pyle repair facility. Please observe and obey the local laws and regulations when installing the unit. Upon Installation, please make sure as to not to interfere with any of the vehicle's safety features, wiring, components, etc. We are not responsible for any damages, injury, malfunctions or otherwise noted due to faulty or non‐professional installation. Connection / Installation: The camera has the ability to connect up to 4 cameras (2 wired and 2 wireless ‐ the wired cameras can be connected via the included power and wiring harness, having 2 connector jacks featuring 4‐pin styled connectors. If you desire to take advantage of this optional feature, and connect additional cameras, please be sure to use compatible cameras with threaded locking 4‐pin connectors. *Please visit www.pyleaudio.com to learn more about system compatibility and optional compatible parts. Camera & Monitor feature built‐in transmitters and receivers, the included antennas need to be connected to the camera and monitor to send & receive the wireless video signals. Wireless signal transmission range up to 300' feet. This system includes one camera with built‐in 2.4G wireless transmitter. The camera can be used as a reverse camera (placed in the rear of your vehicle) or normal safety driving camera to display the picture as viewed through the lens (when placed on the sides or facing the front of your vehicle). If used as a reverse camera, be sure to wire the 'Reverse Trigger (Green)' cable accordingly. Users will have also have the ability to flip the camera picture as displayed on the LCD screen display. The button controls on the monitor panel allow the picture to be flipped horizontally (Left / Right) for backup rearview camera viewing. Not flipping the picture will out the camera picture to the monitor displays the camera picture as seen through the camera lens. This type of display output is used for any camera facing the front of your vehicle.
PLCMTR ‐ Commercial Grade Camera System
www.pyleaudio.com
Wiring & Connection
2.4G Antennas Channel 1 ‐ 2370MHz Channel 2 ‐ 2510MHz
Use the wiring chart above to connect your camera system accordingly. If multiple cameras are used the colored trigger wires serve as automatic camera and display activation connections.
Channels 1 & 2 are reserved for wireless camera connection. Channels 3 & 4 are reserved for wired camera, as the included power and power harness has 2 additional input connectors for compatible 4‐pin cameras. These options are available for users who wish to connect additional cameras to the system. Please note, system installation includes optional methods of camera setup as users can choose to incorporate additional camera sources to the camera and video system. *Please visit www.pyleaudio.com to learn more about system compatibility and optional compatible parts.
PLCMTR ‐ Commercial Grade Camera System
7'' Display Monitor
B C D E F G H I J K L M N O
Menu Video Input 1 ‐ Ch.1 Video Input 2 ‐ Ch.2 Power Video Input 3 ‐ Ch.3 Video Input 4 ‐ Ch.4 Mode Remote Control Receiver Remote Control Receiver LCD Display Screen Wireless Antenna Sun Shade Angle Adjustment Knob Display Mounting Bracket
Please note, in cold weather and temperatures, the
display monitor may require some time to 'warm up' to clearly display a picture on screen.
Monitor Stand Mounting
www.pyleaudio.com
PLCMTR ‐ Commercial Grade Camera System
www.pyleaudio.com
The U‐shaped mount stand bracket separates from the LCD display housing for attachment / fixture. The U‐shaped bracket attaches to the desired location via 3 screw holes located at the base of the bracket. Please remove the LCD display monitor from the bracket before attempting to secure the bracket to your desired location. Once screwed into the desired location, attach the LCD display monitor housing and tighten with the tightening knob to the side of the housing. Adjust the angle / tilt of the LCD display before tightening the side knob. Model: PLCMTR82WIR Wireless Weatherproof Rearview Backup Camera & Monitor Video System, Commercial Grade, Night Vision Camera, 7'' Display, Dual DC 12‐24V for Bus, Truck, Trailer, Van Camera & Monitor Vehicle Safety Video System Wireless 2.4G Signal Transmitter & Receiver Wireless Range: Over 300' Feet Designed for Car/Truck use 12/24 Volt Systems Includes All Necessary Cables & Wiring Monitor: 7 inch TFT LCD Display Wireless Receiver Built‐into Display
System Includes: Monitor with Built‐in Receiver Camera with Built‐in Transmitter Power & Wiring Harness Camera DC Power Cable (2) 2.4G Wireless Antennas
Aspect Ratio: 16:9 Widescreen System: PAL/NTSC Auto Switching Anti Glare Sun Shade Universal Stand Mount Resolution: 800 x 480 Pixels Brightness: 350 cd/m2 OSD Menu with Front Panel Button Controls Brightness, Color, Contrast Adjustable 4‐Pin System Connectivity Jacks Ability to Connect up to 4 Cameras (2 Wireless, 2 Wired) DC Reverse 12‐24 Volt Trigger with Auto Activation Dimensions: (L x W x H): 7.1'' x 2.9'' x 4.7''
Camera: Weatherproof Rearview Camera System Wireless Transmitter Built‐into Camera Weatherproof Marine Grade Construction IP68 Rating Water & Fog Resistance LED Lights with IR Night Vision Illumination Low Lux Light Performance Image Sensor: SHARP Color 1/4'' CMD System: PAL/NTSC Auto Switching Video Output 1.0V pp‐75 Ohm Lens Angle: 170 Degree Min. Illumination: 0.2 Lux Auto Image Adjustment Camera Dimensions (W x H x D): 3.18" x 2.95" x 2.17"