Transcript
PoE – Extractors, Splitters and Back -up Supplies
POE-EXT, POE-SPT and BSU-48100
EXT*
I I I I
SPT*
EXT - PoE + 12VDC-1A output SPT - 12VDC-0,5A output BSU – back-up supplies Operating temperature from –40°C
BSU* ORDERING NAME
CODE
SUPPLY
POE-EXT-1212-BOX **
4-100-110
PoE+
POE-SPT-05-1212-BOX **
4-100-111
PoE / PoE+
BSU -48100-BOX
4-100-112
48VDC
** compatible only with LAN -BUS , LAN -RING switches
*holder DIN35-LOCK for mounting to DIN 35 not included
EXT = 10/100Mbps + PoE+ / PoE + 12VDC/1A switch
IR
LAN-BUS LAN-RING
LEGEND UTP Cat5e or higher Supply
12VDC-1A 10/100 M + PoE+ PoE mode B
10/100M + PoE
EXT
SPT = 10/100Mbps + PoE(+) / PoE(+) + 12VDC/0,5A switch
IR
LAN-BUS LAN-RING
12VDC-0,5A
10/100M + PoE(+) PoE mode B
SPT
10/100M
230VAC
BSU-48100 – Back-up supply48VDC Overvoltage Protection Class D
230VAC
www.metel.eu
Switched supply: ML100.105 QS10.481 SU-230/4870
Back-up: BSU-48100
Primary supply input 48VDC SWITCH Redundant supply input 48VDC
AKU 5/10 1/8
Installation manual REV:201101
POE-EXT, POE-SPT a BSU-48100 PoE – Extractors, Splitters and Back-up Supplies
PoE-EXT – description and technical parameters PoE-EXT are PoE extractors with 10/100M PoE+ input. From the input PoE+ supply of METEL switches of LAN-RING series, it is possible to supply one PoE compatible device and one device supplied by 12VDC/max. 1A. A typical example is supplying of PoE camera and IR illumination.
Input RJ45
Output RJ45
Output terminal board
Dimensions
Parameter
Value
Unit
Note
Speed
10/100
Mbps
IEEE802.3
Supply
PoE/ PoE+
Speed
10/100
PoE mode B
Supply
PoE
Voltage
12
VDC
Current
max. 1
A
BOX:
page 5, DXF, VISIO
Mbps
IEEE802.3 PoE mode B
The producer retains the right to change any technical parameters without previous announcement.
PoE-SPT – description and technical parameters PoE-SPT are PoE splitters with 10/100M PoE+ input. From the input PoE+ supply of METEL switches of LAN-RING or LAN-BUS series, it is possible to supply one PoE incompatible device 12VDC/max. 0,5A. A typical example is connection of a camera incompatible with PoE and supplying of IR illumination. Parameter
Value
Unit
Note
Speed
10/100
Mbps
IEEE802.3
Supply
PoE/ PoE+
Output RJ45
Speed
10/100
Mbps
Output terminal board
Voltage
12
VDC
Current
max. 0,5
A
BOX:
page 5, DXF, VISIO
Input RJ45
Dimensions
PoE mode B IEEE802.3
The producer retains the right to change any technical parameters without previous announcement.
BSU-48100 – description and technical parameters BSU-48100 are back-up modules of PoE supply +48VDC. Typical application of BSU-48100 is backing-up of ML100.105 and QS10.481 sources supplying METEL switches. Parameters of supply can be set by DIP switches on the supplies or over Ethernet from SIMULand software. RS485 bus is used for interconnection with LAN-RING switches. Back-up: lead-acid accumulator 12V (gel) - automatic check of battery level - charging to constant voltage with current limit - overcharge check - periodic check of charge, keeping the battery charged - charge and discharge state indication - automatic back-up switch-on on main supply voltage drop - automatic back-up switch-off – prevention of complete discharge - communication bus EIA485 - setting, state monitoring, parameter list Parameter
Value
Unit
Input
Voltage
45-60
VDC
Output
Voltage
48
VDC
Dimensions
Power consumption
max. 100
W
Max. charging current
5
A
Max. discharging current
10
A
BOX:
page 8, DXF, VISIO
The producer retains the right to change any technical parameters without previous announcement.
www.metel.eu
2/8
Note
Installation manual REV:201101
POE-EXT, POE-SPT a BSU-48100 PoE – Extractors, Splitters and Back-up Supplies
POE-EXT-1212-BOX 12VDC load IR illumination
Installation and Setting 1. Converter mounting Screw the extractor to flat surface or attach to DIN35. Mounting holders and screws are included.
10/100 BaseTx PoE PD* device
NOTE1: In case of installation in outdoor environment we recommend combining the extractor with overvoltage protection BREAK-100M/PoE-B.
PoE
RJ45 10/100 Base-T LAN+ PoE
4. Connect the device supplied by 12VDC/1A Connect the device that is supposed to be supplied from the extractor to the terminal board labelled 12VDC.
+
3. Connect end ethernet device According to the picture connect the end ethernet PoE compatible device using UTP cable.
12VDC/1A
2. Connect Ethernet with PoE(+) According to the picture connect ethernet 10/100Mbps (IEEE802.3) to PoE(+) of LAN-RING switch using UTP cable.
NOTE2: When supplying from PoE switches LAN-BUS max. available power on the output is 15.4W.
PoE(+)
RJ45 10/100 Base-T
* standard IEEE802.3-at 2009 defines PoE PSE device – „power supply device“, i.e. source of PoE supply PoE PD device – „powered device“, i.e. device supplied from PoE
PoE+ switch LAN-RING (PoE PSE device*) www.metel.eu
3/8
Installation manual REV:201101
POE-EXT, POE-SPT a BSU-48100 PoE – Extractors, Splitters and Back-up Supplies
POE-SPT-1212-BOX 12VDC load
10/100 BaseTx device
IR illumination
Installation and Setting 1. Converter mounting Screw the splitter to flat surface or attach to DIN35. Mounting holders and screws are included.
230VAC
RJ45 10/100 Base-T LAN
PoE PD* device
NOTE1: In case of installation in outdoor environment we recommend combining the splitter with overvoltage protection BREAK-100M/PoE-B. NOTE2: When supplying from PoE switches LAN-BUS max. available power on the output is 15.4W.
RJ45 10/100 Base-T
* standard IEEE802.3-at 2009 defines PoE PSE device – „power supply device“, i.e. source of PoE supply PoE PD device – „powered device“, i.e. device supplied from PoE
PoE(+)
4. Connect the device supplied by 12VDC/0,5A Connect the device that is supposed to be supplied from the splitter to the terminal board labelled 12VDC.
+
3. Connect end ethernet device According to the picture connect the end ethernet device using UTP cable.
12VDC/0,5A
2. Connect Ethernet with PoE(+) According to the picture connect ethernet 10/100Mbps (IEEE802.3) to PoE(+) of LAN-RING or LAN-BUS switch using UTP cable.
PoE+ switch LAN-RING (PoE PSE device*) www.metel.eu
4/8
Installation manual REV:201101
POE-EXT, POE-SPT a BSU-48100 PoE – Extractors, Splitters and Back-up Supplies
Installation of POE-EXT and SPT to flat surface or DIN35
51,50
30,00
70,00
60,00
www.metel.eu
5/8
Installation manual REV:201101
POE-EXT, POE-SPT a BSU-48100 PoE – Extractors, Splitters and Back-up Supplies
BSU-48100-BOX Installation and Setting 1. Converter mounting Screw the module to flat surface or attach to DIN35. Mounting holders and screws are included. 2. Connect input supply 48VDC According to the pictures below connect supply 48VDC.
ACCU
Supply feed 48VDC
BSU-48100-BOX
ACCU
Supply feed 48VDC
BSU-48100-BOX
Backed-up device
Backed-up device
Redundant supply input 3. Connect the accumulator Set charging current using DIP switches. DIP 1 in position ON - Charging current is set over RS485 from SIMULand software. DIP 1 in position OFF - Charging current is set by DIP switches DIP2, DIP3 and DIP4. DIP2 DIP3 DIP4 Charging current OFF OFF OFF 1.5 A ON OFF OFF 2A OFF ON OFF 2.5 A ON ON OFF 3A OFF OFF ON 3.5 A ON OFF ON 4A OFF ON ON 4.5 A ON ON ON 5A Set operating mode using DIP5 and DIP6 switches. DIP5 DIP6 Mode OFF OFF supplying load without recharging of accumulator ON OFF charging accumulator, output 48VDC is off OFF ON charging ON-LINE (output 48VDC is activated continually*) ON ON charging OFF-LINE (output 48VDC is activated only on input supply failure*) * Output voltage on Vout+ terminal must be set by Vout trimmer to value 1V lower than input voltage. Therefore, default factory setting of module output voltage is 47VDC. 4. Connect backed-up device According to the pictures at paragraph 2 connect the backed-up device. Indication LEDs on the front panel indicate LED POWER – on -> active supply of processor part, i.e. the device is on LED ERROR – on -> module failure, e.g. battery not connected, battery short-circuited, ... LED CHARGER - indicates charging status off -> charging is off fast blinking -> test of battery connection slow blinking -> charging in “current charging” mode on and periodically short off -> charging in “voltage limiting” mode (battery almost charged) on -> battery is fully charged LED OUTPUT - off -> output voltage is not generated on -> output voltage is generated and accumulator is OK blinking -> output voltage is generated and accumulator is close to discharge
www.metel.eu
6/8
Installation manual REV:201101
POE-EXT, POE-SPT a BSU-48100 PoE – Extractors, Splitters and Back-up Supplies
BSU-48100-BOX 5. Connect RS485 In case of module setting and monitoring over RS485 bus connect terminals RS485 A+ positive RS485 wire RS485 B- negative RS485 wire GND data cable shielding (connect only for STP/FTP cables) Communication speed is 9.6kbps, no parity, 1 stop bit. Tools for setting over Ethernet will be implemented to SIMULand software by 1st May 2011.
BSU-48100-BOX schema of LAN-RING switches back-up Main supply input 230VAC
SU-230/4870H ML100.105 QS10.481
ACCU
Main supply input +48VDC
Main supply input +48VDC
RS485 port B+ A-
Switch LAN-RING
Redundant supply input +48VDC
www.metel.eu
7/8
Installation manual REV:201101
POE-EXT, POE-SPT a BSU-48100 PoE – Extractors, Splitters and Back-up Supplies
Installation of BSU-48100-BOX to flat surface or DIN35
60.00
109.00
1 2
3
4
5
6
165.00
ON
119.00
www.metel.eu
8/8
