Polo Monobloc Basin Mixer, No Waste

Transcript

Polo monobloc basin mixer, no waste Monobloc basin mixer, no waste Size Pattern No. Pack 1 Qty Pack 2 Qty Code Barcode Price (£) ex VAT test N/A Basin Mixer No Waste 1 4 444903 5022050376794 £179.42 5 Year Guarantee Luxury Taps and Mixers Pegler Yorkshire Customcare 5 Year Guarantee - Terms and Conditions Product are subject to a 5 year guarantee that is between Pegler Yorkshire and the final purchaser of the product. The guarantee is subject to proof of purchase being supplied. This guarantee does not affect any statutory rights the consumer may have in law. The guarantee covers manufacturing or material defects and does not cover parts subject to normal wear and tear. Finishes other than chrome are covered for a period of 3 years only and the guarantee on the finish is subject to the cleaning instructions being followed. The guarantee is not applicable where the product is fitted contrary to the conditions in the fitting instructions. Abusive behaviour and accidental damage to the product are not covered by this guarantee. The extent of this liability is limited to the cost of the replacement of the defective item and not to fitting or consequential damages. Description Minimum Operating Pressure (bar) Maximum Cold Working Pressure (bar) Maximum Hot Working Pressure (bar) Monobloc basin mixer, no waste 0.1 bar 10.0 bar at temperatures up to 85oC Not Suitable for Maximum Hot Working Pressure Care To maintain the surface finish, simply wipe occasionally with a mild detergent on a soft damp cloth. Dry, using a soft cloth. Never use abrasive cleaners or chemical household cleaners and avoid contact with concentrated bleach. Maintenance No regular maintenance is required for this product. In case of complete replacement Pegler recommend service valves should be fitted to the supply inlets. For any further help or replacement parts please contact the Service Support Team on 0800 1560050. Regulations It is important to ensure that the water supplies to your taps and mixers are connected in accordance with the water regulations (WRAS) requirements and good plumbing practice. It is Pegler’s recommendation and good plumbing practice that the supplies of hot and cold water to the mixer should be at equal (balanced) pressures in order to provide a consistent flow. Supplies should be from a common source, either mains or tank fed. If supplies are not equal pressures then non return valves should be fitted. Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF Telephone: Phone +44 (0) 844 243 4400 Fax: +44 (0) 844 243 9870 Website: www.pegleryorkshire.co.uk Registered office : Pegler Yorkshire Group Ltd, St Catherine's Ave, Doncaster, S Yorkshire, DN4 8DF Company no : 00401507 MONOBLOC BASIN / KITCHEN Model P565 and P525 are supplied with separate inlet flexible tails. i) Screw inlet tails into body and tighten up ensuring ‘O’ ring seal is firmly in place and leak proof. ii) Place anti-rotational washer on base of body and place vertical pop-up rod through hole in body (top portion only). iii) Place fitting through hole in ware. Place fibre washer over inlet tails and position on underside of ware. Place clamping plate onto threaded stud ensuring that stud is positioned in the slot in the plate and the inlet tails are positioned in the cut out in the plate.Place fixing nut onto threaded stud and tighten firmly up the base of ware/worktop. iv) Fit Pop-up Waste ( Basin Monobloc only ) a) Remove plastic cover and pop-up plug. Unscrew flange portion and fit to ware ensuring the shaped sealing gasket is located under the flange. Offer up the lower waste portion to the underside of the ware ensuring the lower sealing gasket is trapped between the ware and the waste. b) Tighten firmly to ensure no leaks occur. Ensure the horizontal rod is pointing to the back of the ware. c) Place connecting clip onto the horizontal rod. d) Screw lower part of vertical pop-up rod onto upper part. e) Lift the vertical rod upwards and pass through the hole in the connecting clip. Position the vertical rod to its lowest position. Tighten the clamping screws of the connecting clip to both horizontal and vertical rods. f) Place the plug in the waste and lift the pop-up rod to ensure that the plug in the waste and lift the pop-up rod to ensure that the plug seats correctly. Adjustment to the plug position is made by the regulating screw in the bottom of the pop-up plug. v) Connect hot and cold supplies by using 15mm (Prestex) male x copper compression ( sold separately) Please note the cold supply is on the right and the hot supply is on the left when viewed from front. vi) Ensure pipework is thoroughly flushed to remove debris before connecting to the fitting. Fit handle Place snap fit connector (A) onto spline (B) and screw down firmly using screw provided (C). Place handle (D) over connector and push firmly until it snaps home. If the handles are not in the required position remove them with a sharp tug and replace to suit. Your Guide to the installation, care and maintenance of POLO Luxury Taps and Mixers Show flat sided spindle BATH SHOWER MIXER / BATH FILLER / SINK MIXER i) Remove backnuts from inlet tails and fit tails through tap holes of ware ensuring base rubber is trapped between ware/worktop and fitting. ii) Replace and tighten backnuts from beneath. iii) Thoroughly flush pipework and connect tap to the supplies ensuring hot is on the left and cold on the right when viewing the mixer from the front. iv) Fit shower hose to the bath/shower mixer. P501 1/2” Basin Taps P501 3/4” Basin Taps P502 High Neck Pillar taps P565 Basin Mixer P521 Deck Sink Mixer P525 Mono Sink Mixer CARE AND MAINTENANCE To maintain the surface finishes, simply wipe occasionally with a mild detergent on a soft damp cloth. Dry using a soft cloth, never use abrasive cleansers or chemical household cleaners, avoid contact with concentrated bleach. Leger products are manufactured to the highest of standards and should require little or no maintenance. In the unlikely event of any spare part requirements, please contact your nearest stockist or the Pegler Sales Office, St. Catherine’s Avenue, Doncaster DN4 8DF, Telephone 01302 368581. P550 Deck Bath Shower Mixer P557 Bath Filler PERFORMA Pegler Limited, St. Catherine’s Avenue, Doncaster. DN4 8DF Telephone: 01302 560560 Fax: 01302 367661 DIMENSIONAL INFORMATION WATER BYELAW REQUIREMENTS 164mm CRS It is important to ensure that the water supplies to your taps and mixers are connected in accordance with the water regulations (WRAS) requirements and good plumbing practice. 180mm CRS 73.5mm 170 mm 144 mm 73.5mm 73.5mm 70 mm 72mm 37 mm 38mm 113mm CRS 67mm 180mm CRS 180mm CRS 116mm CRS It is pegler recommendation and good plumbing practice that the supplies of hot and cold to the bath mixer should be at equal (balanced) pressures in order to provide a safe, maintained showering temperature. Supplies should be from a common source, either mains or tank fed. If supplied are not equal pressures then non return valves (801 check valves), (not supplied) should be fitted in each inlet supply line. It is recommended that in all new and refurbishment installations a thermostatic mixing valve is designed to prevent scalding when using the hot water supply. 28mm P557 Bath Filler P550 Deck Bath Shower Mixer P521 Deck Sink Mixer WATER SUPPLY PRESSURES 165mm CRS 72mm CRS Pegler fittings have been designed to function under under the following conditions. P501 1/2” Basin Taps Minimum supply pressure 0.1 bar Maximum supply pressure 10 bar 149mm 168mm CRS 109 mm 195 mm Should excessive flow be experienced, then it may be necessary to install a Pressure reducing valve (not supplied). It is our recommendation and good plumbing practice that a service valve (fig.806) should be installed in the inlet supply line. 77 mm 67mm 101 mm 169 mm INSTALLATION 28mm 112mm CRS 164mm CRS P525 Mono Sink Mixer 78mm CRS 80mm CRS P501 3/4” Basin Taps P565 Basin Mixer P502 High Neck Pillar taps PILLAR TAPS i) Remove backnut from tap tail. ii) Fit tap through ware ensuring anti-rotational washer is trapped in position between tap base and ware, replace backnut and tighten. iii) Thoroughly flush pipework and connect to tap. Hot should be on the left and cold on the right when viewing pipework from the front.