Transcript
TROUBLE SHOOTING GUIDE
OPERATING INSTRUCTIONS
INSTALLATION INSTRUCTIONS
If the Pump and Motor runs but there is little or no water flow, the following conditions may apply:-
STARTING PUMP
The “Enduro” Pump has been designed to work with a variety of filter types including Sand, Cartridge and Diatomaceous Earth. The installation of the Enduro Pump should be carried out by an experienced Pool Plumbing, Pump and Filter Installer.
1. Check to see if the Filter needs cleaning or is blocked - refer to Filter Instruction Manual. 2. Pump is not primed - re-prime as per instructions in “Starting Pump”. 3. Air leaks in suction lines - Check for air bubbles under Clear Lid and tighten. Check all pipes and connections and repair if necessary. 4. Water on ground under the Pump and Motor usually indicates a damaged Pump Shaft Seal - this should be repaired immediately or further damage may occur. 5. Pump unable to draw water from the pool - check that Valves to the Pump are fully open and that the water level is correct in the pool. 6. Blockages - Check Strainer Basket and Pool Skimmer Basket are free of obstruction. If a blockage is suspected inside the Pump or in the Pipework the advice of your pool service technician should be sought. If the motor does not run, the problem could be that:1. Power not connected - Check power point by plugging in a portable appliance to ensure power is available. Also check Fuses and Main Power Supply Switch. 2. Overload tripped - Poolrite Motors incorporate an Internal Switch that will reset automatically after the Motor has cooled. 3. Blockage preventing Pump from rotating. 4. Motor fused or “burnt out” - “burning” smell evident - replacement may be required.
Before switching the pump ON check that all Pipework is properly sealed and that the pool water is at the recommended level (check with your Pool Builder). 1a. Self Priming Pump with Strainer Pot First prime the Pump by removing the Clear Lid by unscrewing in an anticlockwise direction. Fill the Strainer Pot with water to the Suction Port. Replace the Lid ensuring that it is sealed on the Gasket properly and tighten in a clockwise direction.
2. The Pump should be placed on a secure and level concrete block or similar base 600 x 300mm in size (Pump only) and should be placed in a location that cannot be flooded by storm water or by accidental immersion.
2. Connect to power supply and switch ON.
3. The rear of the Motor should be no closer than 150mm from a wall, fence or any other barrier to allow for adequate airflow to cool the Motor.
3. Allow Pump to run discharging the water back to the pool. 4. If flow is not established within approximately 1 minute, switch off the Pump and repeat procedure. Continued failure to prime may indicate an air leak in the suction line which should be rectified. ROUTINE MAINTENANCE The Strainer Basket should be inspected frequently through the Clear Lid and emptied as follows when a build-up of rubbish is evident.
4. The Suction and Discharge Ports are provided with Union Adaptors for quick disconnection. These connectors will accept either 40mm or 50mm PVC pipe and should be joined to the pipe with PVC Solvent Cement. Suction lines should be no smaller than as follows:Max Suction Line Length
Min. PVC pipe size
1. Switch off Pump.
EP 750
12m
50mm
2. Remove Clear Lid.
EP 900
12m
50mm
3. Remove Strainer Basket.
EP 1100
12m
50mm
4. Empty accumulated rubbish and hose Strainer Basket clean. 6. If Strainer Pot has emptied of water, repeat steps in “Starting the Pump”.
The Pump Motor is an electrical device and as such should not be disassembled or serviced by anyone other than an authorised Poolrite Service Technician or qualified Electricial Service Company.
WATER LEAKS
Also, any other problems that cannot be corrected by routine maintenance should be attended to by an experienced Pool Service Technician.
PIPE CONNECTION
Pump Model
Warning
Young children should be supervised to ensure that they do not play with the appliance.
1. Install at a distance no more than 12 metres from the Pool or Spa and no more than 1 metre above water level or 1 metre below water level in the case of the Self-Priming Pump with Strainer Pot. If the pool is to be installed outside these parameters, seek the advice of your local Poolrite Distributor.
1b. Non Self Priming Pump without Hair and Lint Pot The Non Self Priming Pump should always be installed below the pool water level, therefore ensure the suction pipe and pump body are filled with water.
5. Replace Strainer Basket.
The appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely.
LOCATION
7. Water leaking from under the Pump and Motor should be attended to immediately as this would indicate a failure of the Pump Shaft Seal. If this seal is not immediately replaced damage may occur. 8. Pool water leaking onto the pump motor from associated plumbing should be attended to immediately before damage occurs. MOTOR NOISE 9. If the Pump Motor starts to get “noisy” the Motor should be checked by a Pool Technician to ascertain whether the Motor Bearings need replacement. This should be attended to immediately as Bearing failure may cause Motor burn out. LARGE AIR BUBBLES UNDER THE STRAINER POT LID 10. Check the Gasket under the Clear Lid and check the pipe connection to the Suction Port at the front of the Pump to make sure it is tight - do not overtighten. CHEMICAL BALANCE GUIDE 11. The unit is designed to be used for Spa or Swimming Pool water, balanced in accordance with Langlier Saturation Index, with a pH level of 7.0 to 8.0 and is regularly treated with a chlorine Sanitising agent, the level not exceeding 3000 PPM.
Discharge pipe should be no smaller than 40mm. When installed below water level, Shut-off Valves should be fitted to the Suction and Discharge Lines which should be free from air leaks. The discharge from the Pump Outlet should be connected to the Inlet of the Filter and the Suction Port connected to the Skimmer Box or Suction Outlet from the Pool or Spa. WEATHER PROTECTION 5. The Enduro Pump is completely Weatherproof and therefore no enclosure is necessary. However should it be desirable to install the Pump in an enclosure, the enclosure must have both a ventilation inlet and outlet opening to allow cooling airflow around the Pump Motor. Each opening should be at least 200 sq cm in area as close as practicable to the Pump. POWER CONNECTION 6. The Enduro Pump is designed to be connected to a nominal 240 volt 50Hz power supply and is supplied with a 1.8 metre lead and 3 Pin Plug. A Weatherproof 3 Pin Power Point should be fitted by an electrician in a dry place, shielded from pool water splash over. EXTENSION LEADS ARE NOT RECOMMENDED FOR USE WITH THIS EQUIPMENT BECAUSE THEY ARE UNSAFE IN AND AROUND THE POOL ZONE.
pppppppppppppppppppppppp ENDURO PUMP WARRANTY p ENDURO PUMP WARRANTY p In addition to the conditions of sale and warranties implied at law and which may p p In addition to the conditions of sale and warranties implied at law not be excluded, Evolve Supply Chain warrants the Enduro Pump to be free from p and which may not be excluded, Poolrite warrants the Enduro p defect for a period of two (2) years from the date of purchase by the Owner from Pump to be free from defect for a period of two (2) years from p p Evolve or an authorised of the Enduro Pump. the dateChain of purchase by supplier the Owner from Poolrite or an p p Supply authorised supplier of the Enduro Evolve Supply Chain will authorise a qualifiedPump. technician to repair the Enduro p p Poolrite Pump providedwill that:repair, or authorise a qualified technician to repair, p p the Enduro Pump provided that: p • Evolve Supply is Chain is notified seven (7) days defectbeing being p Poolrite notified withinwithin seven (7) days of of thethedefect pdetected; p detected; p the Enduro Pump has not undergone any unauthorised p • the Enduro Pump has not undergone any unauthorised modification or been p modification or been fitted with other than genuine Poolrite p with other parts; than genuine and Poolrite approved parts; and pfittedapproved p Enduro Pump has been installedin and operated in p • the the Enduro Pump has been installed and operated accordance with the p accordance withand theOperating Installation Instructions and Operating p Instructions Instructions, respectively. pInstallation Instructions, respectively. p p Evolve Supply Chain will not liabletoto repair repair the PumpPump if the repair pppppppppppppppppppppppp Poolrite will not be be liable theEnduro Enduro if theis p p necessary because of misuse, accidental damage, entry of foreign objects or repair is necessary because of misuse, accidental damage, p ENDURO PUMP WARRANTY p p p entry of foreign objects or materials into the equipment, improper materials into the equipment, improper or inadequate maintenance or repair or p In addition to the conditions of sale and warranties implied at law p or inadequate maintenance or repair or incorrect operation of p p incorrect operation of the Enduro Pump. p and which may not be excluded, Poolrite warrants the Enduro p the Enduro Pump. p Pump p todoes be free from defect fortoa wear period two (2) Enduro years from p ThisThis warranty notdoes extend reasonable andoftear of the Pump. warranty notto extend reasonable wear and tear of p p p the date of purchase by the Owner from Poolrite or an p p the Enduro All repairs must supplier bePump. undertaken byEnduro a technician authorised by Evolve Supply p p authorised of the Pump. p All repairs must be undertaken by Poolrite or a technician p Chain. p Poolrite willbyrepair, or authorise a qualified technician to repair, p authorised Poolrite. p p the Enduro Pump provided p p The The OwnerOwner will be will responsible for allthat: freight travelling charges. Evolve p be responsible for and/or all freight and/or travelling p Poolrite is notified within seven (7) days of the defect being p p charges. Poolrite accepts no responsibility for goods while in Supply Chain accepts no responsibility for goods while in transit. p detected; p p p transit. p Evolvethe Supply Chain accepts no for representations other than p Enduro Pump hasresponsibility not undergone any unauthorised p Poolrite accepts no responsibility for representations other than p p p modification beeninfitted withbyother than genuine expressly contained inorliterature published Evolve Supply Chain. InPoolrite particular expressly contained literature published by Poolrite. In p p approved parts; and p Evolve Supply Chain has made representation as to the fitness thefitness Enduro p particular Poolrite has no made no representation as toofthe p p Enduro been installed andliterature. operated in p p Pump forthe any particularPump purposehas except as particular contained in purpose such ofthe Enduro Pump for any except as p p accordance with the Installation Instructions and Operating p contained in such literature. p Instructions, respectively. p p p Poolrite will not be liable to repair the Enduro Pump if the p pppppppppppppppppppppppp p repair isComplete, detach and return to The Evolve Group damage, p necessary because of misuse, accidental p entry of foreign objects or materials p into the equipment, improper Complete, detach and return to Poolrite. p or inadequate maintenance or repair or incorrect operation of p WARRANTY CARD p the Enduro Pump. p This warranty does not extend to reasonable wear and tear of p p WARRANTY CARD Name of Purchaser:_____________________________________________ p the Enduro Pump. p All repairs must be undertaken by Poolrite or a technician p p Address:______________________________________________________ authorised by Poolrite. Name Purchaser: p Theof Owner p will be responsible for all freight and/or travelling p _____________________________________________________________ charges. Poolrite accepts no responsibility for goods while in p Address: p transit. p _____________________________________________________________ p Poolrite accepts no responsibility for representations other than p p expressly contained in literature published by Poolrite. In p particular Poolrite has made no representation as to the fitness p Purchased From:_______________________________________________ p of the From: Enduro Pump for any particular purpose except as Purchased p contained in such literature. p Date:_________________________________________________________ p p Date: pppppppppppppppppppppppp Equipment and Model:__________________________________________
CUSTOMER RECORD Customer Record Purchased From:_______________________________________________ Purchased From: _______________________________________________________ Purchase Date: Purchase Date:_ ________________________________________________
ENDURO Swimming Pool & Spa Pool Pump
�
�
Installation Instructions
�
ENDURO
CUSTOMER RECORD Purchased From:
Swimming Pool & Spa Pool Pump
Purchase Date:
ENDURO
�
�
Installation Instructions SWIMMING POOL PUMP
�
✄
✄
Equipment and Model:
✄
✄
Complete, detach and return to Poolrite.
✄
POOLRITE EQUIPMENT PTY LTD
The Evolve Group
A.B.N. 11 001 674 004
✄
PO Box 3077Road, Clontarf, QLD Australia WARRANTY CARD 415 Creek (P.O. Box 520) 4019 Phone: +61 7 3283 1196 | Fax: +61 7 3883 1560 Mt. Gravatt. QLD. 4122 Australia EQUIPMENT Email:
[email protected] Telephone: (07) 3323 6555 | www.poolrite.com Fax: (07) 3323 6500 Name of Purchaser: Address:
Stella Print Item No. 22534 (6/05)
QUICK START GUIDE
