Transcript
PoolStar™ 3000
1
Instructions for the Through The Wall Above Ground Pool Light INSTALLATION ON POOLS W/FACTORY REINFORCED HOLE – should be installed prior to filling, otherwise, drain water 6” below reinforcement before proceeding. 1. Locate the factory installed 2½” reinforced hole midway down the pool wall (end of pool, near return) and carefully cut out the center of the hole. Make sure to use a sharp blade and take your time. Proceed to step #2. INSTALLATION ON POOLS W/OUT REINFORCED HOLE (Drain water 6” below return before proceeding) 1. On the end of the pool, near the pump/filter, locate the approx. center of the pool. Use a tape measure, and measure down from the white membrane 3” and place a small pen mark at that point. Center one of the clear peel and stick reinforcements over the mark and carefully cut out the center. Make sure to use a sharp blade and take your time. Next make sure the inside liner of the pool is dry and place the other clear peel and stick reinforcement over the hole from the inside of the pool. Proceed to step #2. 2. Take Large Flange 1000 Series Body, with gasket (Note: single rib side of gasket facing body) around it, and insert it into hole from the inside of the pool. 3. Take other gasket (Note: single rib side of gasket facing DNL Cap) and place against the pool liner, then take DNL Cap, flat side facing pool liner, and screw it on to the backside (outside of pool) of the body. Hand-tighten firmly. Fill pool with water to check for sufficient seal before proceeding. The combination you should now have is Body, Gasket, Pool side/Liner, Gasket, and DNL Cap. 4. The DNL Can has a Ceramic Socket with a 12 volt Light Cord and a halogen reflector already installed. Take the DNL Can and install bulb. The pins, on the bulb, are universal. There is no right or wrong way of inserting the bulb into the socket. Push the male-end pins located on the bulb, into the female ports located on the socket. 5. Take the bulb, socket, and reflector assembly and screw it onto the back of the body located on the DNL Cap previously installed. Turn clockwise approximately one revolution. 6. Take the DNL Can and push it onto the DNL Cap. Position the DNL Can so that the cord hangs down perpendicularly. The 25’ of cord is hardwired to a transformer box with two mounting tabs. The power supply is to be mounted according to the pool manufacturer’s instruction. WARNING – Risk of electric shock. Connect only to a circuit protected by a Ground Fault Circuit Interrupter (GFCI). 7. The power supply comes equipped with an On/Off switch and a 6’ power cord. The Placement of the Power Supply should be close enough to utilize the power cord provided. An extension cord should not be used. 8. Using the power supply as a template, mark the placement of the two #6 x ¾” Phillip Pan-head self-tapping screws provided. 9. Mount Power Supply with Switch and Power Cords facing down. 10. Plug Power Supply into Standard Power Outlet (GFIC Protected). 11. Save Carton that fixture came in for storage purposes.
PoolStar™ 3000
2
Instructions for the Through The Wall Above Ground Pool Light Disassembly for storage of Light Unit 1. 2. 3. 4. 5.
Unplug Power Supply. Locate the four (4) Pry Slots at the joint between the DNL Can and the DNL Cap. Using a Standard “Flat-Head” screwdriver, carefully separate the unit apart. Unscrew the reflector assembly from the back of the light body. Leaving the DNL Cap assembly attached to the poolside, carefully coil up the 25’ of cord and disconnect the power supply from its mounted location. Lifting up and slightly pulling forward on the power supply box does this. 6. Store in box. (Step 11) Reinstallation of Light Unit 1. Follow the installation steps 4, 5, 6, 7, 9, 10, and 11. Lamp Installation 1. Unplug Light unit from power source. 2. Locate the four (4) Pry Slots at the joint between the DNL Can and the DNL Cap 3. Using a Standard “Flat-Head” screwdriver, carefully separate the unit apart *At this point, you have exposed a 12 volt 20 watt halogen bulb. The bulb is attached to the socket by two male prongs extending from the bulb that connect to two female ports on the socket. 4. Pull gently on the bulb to remove it. 5. Take new bulb and insert it into the socket. The tabs are universal. So there is no right or wrong way of inserting the bulb into the socket. Push male end tabs, on bulb, into the female ports on the socket. 6. Take the DNL Can and push it back onto the DNL Cap. Arrange the DNL Can so that the cord hangs down perpendicular to the ground. 7. Plug the Light unit back into the power source
Important Safety Instructions 1. Light fixture is not intended as a step. Using it as a step may cause injury to persons or damage to equipment. 2. Warning – Risk of electrical shock. Connect only to a grounded type receptacle protected by a Ground Fault Circuit Interrupter (GFCI). 3. For a unit that does not have an integral GFCI, contact a qualified electrician if in doubt about whether or not a receptacle is protected by a GFCI 4. An extension cord should not be used. 5. The pool manufacturer determines the maximum water depth of lighting fixture. 6. Do not install on Therapeutic Pools, Hydro massage Bathtubs, Spas, or Hot tubs.
PoolStar™ 3000
3
Instructions for the Through The Wall Above Ground Pool Light
Alternate Power Supply Location Instruction 1. Along with the power supply, you are provided with two, 11” Zip ties. 2. Insert the end of the zip tie through the mounting tab of the Power Supply and around the bail carriage handle. 3. Insert the male end of the zip tie into the locking buckle. Pull the male end through the buckle to form a large loop. You will have approximately 1” of tie exposed. *Do not cinch the zip tie completely down. 4. Repeat steps 1 through 3 for second zip tie installation.
*The PoolStar™ 3000 is to be installed according to the manufacturer and/or authorized dealer.
PoolStar™ 3000
4
Instructions for the Through The Wall Above Ground Pool Light
FOR EVERY ABOVE GROUND POOL “THERE IS LIGHT”
*ETL LISTED *ONE YEAR WARRANTY *EASILY CUSTOMIZABLE
*LOW COST *EASY TO INSTALL *LOW VOLTAGE
