Transcript
POS SYSTEM
5
Installing Optional Items
POS SYSTEM
Model
P2C C-100
P2C P-100
System Configurations
Remove the Hole Cover to install Customer display(VFD), 2nd display 1 Power off the product
1 Open the right side cover to install the MSR as shown in figure 1
Processor
Intel Core™ i3,i5,i7 (3rd generation)
2 Insert the MSR (Hook side in) to the base of the monitor
Intel® Atom™ Processor D2550, Dual Core/1.86 GHz / 512KB x 2 L2 Cache
Chipset
Intel NM10 Express Chipset
Intel QM77 Express Chipset
3 Slide the MSR down to secure the position
Storage Device
2.5" SATA-Ⅱ SSD 64GB (default) or HDD 320GB (optional)
2.5" SATA-III SSD 64GB (default) or HDD 320GB (optional)
4 Connect No.3 cable with I/O port in the right.
Memory
Single-Channel DDR3 Connector for 1066/800MHz x 1, default 2GB up to 4GB
Dual-Channel DDR3 Connector for 1066/800MHz x 1, default 2GB up to 16GB
Graphics
Intel Graphics Media Accelerator 3600
Intel HD Graphics 4000
BIOS
AMI BIOS
2 Remove the rear panel on the bottom fold of the stand and press the Deco panel to separate
1
2
3
3 Rear panel separates from the body as shown on figures 1 and 2 4 Press the bottom part of the open Hole Cover to separate 3
7
Product Specifications
MSR
Installing / Removing Hole Cover
2
POS SYSTEM
6
VFD 1
2
2 Face the back of the VFD to the front of the mount
POS 100 Series C-100
P-100
10°~ 60° Viewing Angle, 300:1 Contrast, Above 350cd/m2 Brightness
3
3 Insert the VFD as shown on Figures 2 and 3
HDD Replacement
1
2
2 Press the HDD lock to release the HDD. Slide the HDD out shown
4 Connect No.12 cable with I/O port in the back side.
in figure 2
2nd display How to set up the BIOS based on the OS type 1
2
3
1
2 x DB9 and 1 x RJ50 Serial Ports, Powered on Pin 9 (DC+5V or DC+12V)
USB
6 x USB A type 2.0, 1 x mini USB B type 2.0
Special USB
1 x mini USB type A, B
VGA / Expansion Slot
D-SUB 15 pin Analog VGA port / miniPCI-e
Cash Drawer
1 x RJ11 (12V) on the Right Rear Side
4 x USB A type 2.0, 2 x USB A type 3.0, 1 x mini USB B type 2.0
10" or 15 with WLED back light (1024 x 768), Single LVDS 24bit or 18bit VGA
1
2
2nd Display
Support 5-wired resistive touch panel (optional)
Customer Display
VFD Type (20 x 2), Alphabet & Numeric, Supports 15° ~ 90° Tilt and 25° Swivel
Touch Panel
Support 5-wired resistive Flat Touch panel
Support tilt (15˚ ~ 45˚) and swivel : 25˚
COM1
COM2 COM3
VGA
COM1
COM2
10°-60° Viewing Angle, 300:1 Contrast, 300cd/m2 Brightness
ISO7811, All Track / USB (default) and Serial (CMOS setting) interface / Bi-Directional reading, min. 1million times reading
MSR
Card reading speed 3inch to 60inch/sec
Smart Card Reader Dallas Reader (i-Button)
2 Change BIOS setting : BIOS > Chipset > Host Bridge > Boot Display Configuration > Select VBIOS>
3 Save BIOS setting : Press F4 to save
Serial Ports
HDD
HDD
1 How to enter the BIOS screen : Turn the system on and press the DEL or F2 button to
. Select Windows XP OS : Other OS . Select Windows 7 OS : Windows 7
1 x 10/100/1000Mbps Base T Ethernet
Options
enter the BIOS screen.
2 Rotate the knob to an open position shown in figure 2.
LAN
Audio Ports /Speaker Out 1 x Mic-in, 1 x Audio-out / 1watt Speaker (Stereo) X 2EA
COM3
the open Hole Cover location.
Supports PCAP Flat or Normal Type Touch Panel (10 points multi touch)
I/O Interfaces
1 Open left cover to replace HDD
with the same shape
4 Connect No.12 cable with I/O port in the back side.
Installation Guide
15" with WLED Backlight (1024 x 768), Single LVDS 24bits / Supports Tilt (0˚ ~ 53˚)
1
Place the rotated open knob hinge to the desired position.
Supported
Supports 5-Wired Resistive Flat or Normal Type Touch Panel
2
3 After installing a dual monitor on the dual-hinge,
POSReady2009, POSReady 7, Windows8.1 industry
Not Supported
Main Display
Rear deco panel
1 Assemble the Dual hinge and Rear Deco Panel on
POSReady2009, POSReady 7
2nd Hard disk(for RAID)
Quick Installation Guide (ver. 1.0.1)
Display
Hole Cover
4
1 Assemble VFD hinge and Rear Deco Panel to the open Hole Cover
OS
POS SYSTEM
ISO7816 EMV level 1 Supports PC/SC(Personal Computer/Smart Card) Dallas Reader (i-Button reader)
Physical Dimension Dimension / Weight
354 x 246 x 339 (W x D x H, mm) / 5.5 (Kg)
Environment Color
White & Black, All Black, White & Red, White & Orange, White & Green
Power Supply / Temperature
100V AC ~ 240V AC, DC12V-5A Adaptor, 60 watt / Operating: 0 ~ 40˚C, Storage: 0 ~ 60˚C
Humidity / Warranty
10 ~ 80% Humidity / 2 years
Certifications
CE, FCC, CB, KC
This manual is provided for informational purposes only, under copyright laws, reproduction, distribution is prohibited. The contents of this manual are subject to change without prior notice.
MADE IN KOREA
POS SYSTEM
1
Safety Instructions
POS SYSTEM
2
Product Composition
POS SYSTEM
you may damage the system.
Right I/O Port
1
Manuals
Stand
6 Prevent external substances from entering the system.
Drivers CD
8 Before disassembling the system, disconnect all power and cables.
13 11
10
4
Product Appearance
11 There is risk of an explosion, If the battery is replaced. incorrectly
6
12
7
Back I/O Port
for business purposes. Distributors and users are advised of this matter.
Display
15 16 17
8
Products front and back
Turning the power on
14
5
assistance or an experienced technician to open the system, especially
2
18
3
Installation Guide
9 Do not remove or repair the system by yourself. We highly recommend an engineer’s
12 This device complies with the EMC (Electromagnetic Compatibility) Regulations,
1
Left I/O Port
2
7 Do not change the motherboard's battery by yourself. It can damage the system.
2
Open knob hinge operation
there is a strong possibility it will lead to a system malfunction or system error. 5 Do not place heavy objects on the system.
1
of the arrow.
Adapter / Power Cord
Body
4 Be careful not to place the system near other high-frequency electromagnetic devices;
Dispose the used batteries according to the manufacturer's instructions.
2 Remove the stand in the direction
3 Avoid exposing the product in direct sunlight or in an enclosed space for a long period of time.
10 An electrical outlet is needed near the device and it should be easily accessible.
1 Rotate the open knob hinge.
Left Right and Back I/O ports are located in body's back side.
1 Before connecting, make sure the operating voltage is AC100 ~ 240V. Otherwise, 2 Do not install the system in an extremely hot or cold place.
4
Body and Stand Installation
I/O Port
Read all safety precautions before using the POS system.
the LCD and touch panels which could be easily broken.
POS SYSTEM
3
Connect the power cord Before connecting the power cord, install all optional items and connect DC jack adapter.
9
Left, Right I/O Port
Please exchange the equipment if you mistakenly sold or purchased this product.
POS terminal security guideline Operating System Security When using an universal OS system with this system,
POWER
. System-provided and managed by the operating system's default security settings must be configured.
When using a wireless network and internet
. Proven safety standard encryption algorithms to be used and the standard authentication protocols.
Stand
User Security Tapping and Skipping of the system is the operator responsibility The system operates in general purpose operating system, the following conditions must be included. . Firewall must be set . Periodically the OS security patches should be applied
A well secured program is needed when working remotely
HDD LED / LAN LED / POWER LED
Power On
Description
MSR
Adapter / Power Cable
1
MIC
7
LAN
13 HDD Slot
2
SPEAKER
8
CASH DRAWER
14 VGA
3
MSR (USB or Serial COM6)
9
POWER (DC 12V)
15 COM1
4
USB1,2
10
rear USB7,8 (pin header type)
16 COM2
5
USB3,4
11
POWER + SATA
17 COM3
6
USB5,6
12
Dual Monitor or CDP (Serial COM4)
18 COM5(optional)
Please turn the power on after installing all optional items. ※ Connect adapter and body first before connecting power cord to a 220V (110V) outlet. Power supply is located on the lower right side of the monitor. When power is connected, the LED will light up. Each LED lamp will indicate the operation status.
1
HDD LED : Operation mode (RED)
2
LAN LED : LAN Connection (ORANGE)
3
POWER LED : Power Connection (BLUE)
1 2
3
