Transcript
POSH - SOLUS MKII SHOWER/BATH MIXER DIVERTER
SPECIFICATIONS Recommended use
Domestic, hotel and commercial
Colour availability
Chrome
Pressure rating
Maximum continuous operating pressure 1000 kpa.
Note: As per AS3500 pressure must be limited to 500
kpa on any new home, extension or renovation.
Note: For best performance and longer life we
recommend 150-500 kPa.
Temperature rating
Maximum continuous working temperature 65°
Suitable Hot Water Units
Storage tank: Yes
Continuous Flow: Yes
Gravity Feed: Not recommended
Warranty (See below)
Body & Finish: 12 months Cartridge: 5 years
Standards
AS/NZS 3718
130
60-84 1/2"GAS
108
28
170
AS
"G
1/2
3/4"GAS 37-60
WARRANTY & CARE DETAILS Dear Customer, This is the warranty by Reece Pty. Ltd. relating to this product. Please keep it together with your purchase receipt. In the unlikely event of a query please contact your nearest Reece Plumbing Centre.
• Normal wear and tear • Inadequate or complete lack of maintenance • Chemical, electrochemical or electrical influences
Warranty
Cleaning Recommendations
You have purchased a quality product from Reece Australia. This product is covered by a 12 month warranty with a further 4 year cartridge replacement warranty. This warranty covers faults in the product construction, material and assembly. Faulty products will be repaired or exchanged free of charge. Faulty items become our property.
Tapware should only be cleaned with a mild liquid domestic cleaner, with soft soapsuds. After cleaning, rinse with clean water and polish with a clean soft cloth. Do not use any corrosive or abrasive cleaning agents containing acids or scouring agents. Damage caused by any improper treatment is not covered by this warranty.
This warranty does not include faults caused by • • •
Unsuitable or improper use Incorrect installation Installation or part installation by the purchaser or any person other than a LICENSED PLUMBER
WaterMark WMKA1400
To the maximum extent permitted by law, Reece excludes all warranties other than those set out above. In the event of a warranty claim, we will replace or repair defective products, or pay for the cost of having defective products repaired or replaced, but will not be liable for any injury to any person, damage to any property, any indirect or consequential loss, or in any other respect.
POSH - SOLUS MKII SHOWER/BATH MIXER DIVERTER
Exploded View 22
9
Item Description
10 11
12
13
21
14 15 16
17
18 19
23
20
24
8 7
6
5
4
3 2 1
1 Indicator cap 2 Grub screw 3 Handle 4 Thermal cap 5 Dome 6 Locking nut 7 Cartridge 8 Internal plate seal 9 Shower mixer diverter cover 10 - 20 Diverter Assembly 21 Cartridge housing 22 Main body
INSTALLATION INSTRUCTIONS Note
noggin and secured with saddles.
Mixer must be installed by a qualified plumber.
Note: Arrow stamped on the outlet must face up toward shower.
Equal pressure for hot and cold water supply is required for this
If the mixer is to be used as a bath mixer, the pipe will need to
single lever mixer. This product may not be suitable where hot
be looped to go to the bath outlet.
water pressure is insufficient.
6. Connect mixer to hot and cold water supply.
Important
7. Connect to bath and shower outlets.
Your mixer comes to you already factory assembled and tested.
8. Pressure check all connections. Leaking joints are not covered
We do not recommend the dismantling of any internal part of the
by the warranty.
mixer. The mixers are factory tested and sealed so as to give the
9. During construction protect the exposed finished surface by
best performance.
using the plastic cover provided. 10. When ready for finishing, remove the plastic cover and
1. Please flush out new pipe work prior to connecting the new
reassemble handle and cap (1 & 3).
mixer. 2. In some areas where the incoming water exceeds 500kpa, an
SERVICING - Replacement of Cartridge
approved pressure limiting device must be installed. Equal
1. Call the plumber, preferably the one that installed the mixer
pressure for hot and cold water supply is required for this
(most problems are caused by supply lines not being cleaned
single lever mixer.
out properly prior to mixer installation). Remove indicator cap
3. Mixers are recommended for use on mains pressure and
(1) and unscrew the locking screw (2).
instantaneous systems only.
2. Lift off lever (3) and remove dress ring and locking nut (5 & 8).
4. When installing the mixer make sure that the cap and handle
3. Lift out cartridge (7) and replace with new, making sure the two
(1 & 3) are removed with the shower diverter cover plate (9).
lugs on bottom of the cartridge sit properly into the allocated
5. In a typical installation, the mixer is mounted on a timber/metal
holes at the base of the body (22).
Disclaimer: Products in this specification manual must by regulation be installed by licensed and registered trade people. The manufacturer/distributor reserves the right to vary specifications or delete models from their range without prior notification. Dimensions and set-outs listed are correct at time of publication however the manufacturer distributor takes no responsibility for printing errors. Tech Page Version 1
