Transcript
P
PowerMaster Plus™400 MODEL F-400S Strip Nailer
PowerMaster Plus™400 IMPORTANT! DO NOT DESTROY Always refer to safety and maintenance manuals #405218 and #405219 for detailed information on this tool. It is the customers responsibility to have all operators and service personnel read and understand this information.
TOOL SCHEMATIC AND PARTS
PARTS LEGEND PowerMaster Plus™F-400S, 500705
30 31 32 33 34 35 36 37 38
*
501043 501016 091873 092757 500707 500461 092042 500407 501001 406041 500455 401946 091208 401950 500456 500454 095432 500453 402906 092971 500709 402011 500710 092235 501002 500866 501020 501023 501333 501334 501013 500516 404274 500525 091622 501010 402669 501009 501008
1 1 4 4 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1 1
39 40 41 42 *43 44 46 47 ▲48 49 ➔ 50 51 52 53 54 55 56 57 58 59 60 61 62 ▲63 64 65 66 67 68 69 70 ** 71 72 73 74 75 76 77 78 79
T.H.S.C.S. 1/4 -20 x 1/2" Air Deflector S.H.C.S. 1/4-20 x 2" Flatwasher 1/4" Cap O-Ring O-Ring Spring, Main Valve Gasket, Cap Retaining Ring Upper Valve Piston Seal, Main Valve O-Ring O-Ring Lower Valve Piston Post O-Ring Bumper, Post B.H.S.C.S.10-32 x 5/8" O-Ring, Piston Piston Assembly Seal Sleeve Sleeve O-Ring, Sleeve O-Ring Bumper Housing Grip, Handle Label, Housing-Leftside Label, Housing-Rightside End Cap, Housing B.H.S.C.S. - Special Flatwasher Locknut, 5/16-24 Reducing Pipe Bushing Trigger Pin, Trigger Spirol Pin Lever, Bottom Trip
Make sure Warning Label (Part No. 500458) is properly affixed. Replace if necessary. Label available at no charge through the Service Department.
▲
Apply Loctite 242 (Blue) Part No. 093500
1 1 1 3 1 1 1 4 4 1 1 1 1 1 1 1 1 1 1 1 1 1 1 2 1 1 1 1 2 2 2 1 2 1 1 1 1 1 1 1
Retaining Ring Spring, Valve Pin Valve Pin Roll Pin 1/8 x 1-1/8" O-Ring, Valve Body Valve Body Nose 30° Lockwasher 5/16 S.H.C.S. 5/16-18 x 1" Spring, W.C.E. Upper W.C.E. S.H.C.S. 1/4-20 x 1/2" Lower W.C.E. Magazine with Wear Strips Nail Cover Follower 3/16 Hex Key, Long Arm End Cap, Magazine-LF End Cap, Magazine-RT Latch Drum Pin Assembly Negator Assembly Nameplate Screw 1/4-28 x 5/8" Front Bracket Spring, Latch S.H.C.S. 8-32 x 2" S.H.C.S. 8-32 x 3/4" Flatwasher #8 Stop Nut Wear Strip Warning Label Logo Label Spring, Trigger Blade Seal Flange, Sleeve O-Ring, Sleeve Lock Washer Flat Washer Sequential Trigger
Air Consumption Chart
Denotes Normal Wear Items
**
402668 097748 097746 071297 092174 401958 500712 095417 009016 501006 501363 091618 500713 500841 500717 500531 501044 501024 501025 501027 501046 500513 500839 404904 500509 501028 501026 066840 404414 404325 500520 500458 500838 500199 500729 500779 500249 002187 404800 501039
SCFM/FASTENER
▲ 1 2 3 4 5 *6 *7 8 *9 10 11 12 *13 *14 15 16 *17 18 19 *20 *21 22 23 *24 *25 *26 27 28 29
WARNING All parts must be periodically inspected and replaced if worn or broken. Failure to do this can affect the tool’s operation and present a safety hazard.
PSI
PowerMaster Plus™400 F-400S 500705
23 76
78
24 51 75
77
Main Valve Assembly 500463
25
26
74
79
ACCESSORIES Sequential Operating Kit This special attachment is designed for sequential operation (stops "contact" firing). The operator must depress and hold the work contacting element against the work surface before pulling the trigger. This sequence must be repeated each time the tool drives a fastener.
Part No.501039
Remote Fire Valve This valve via a positive air signal allows a machine mounted tool to be operated from an automatic air valve or foot pedal system.
Part No. 1X0713
Trigger Valve Kit Repairs trigger valve air leaks.
Part No. 219224
No-Mar Work Contacting Element W.C.E. with a rubber tip prevents you from marring wood surfaces.
Part No.500903
No-Mar Tip Replacement tip for No-Mar Work Contacting Element #500903.
Part No. 501022
Lubricants and Loctite Loctite 242 (Blue) Lubricating Oil 16 oz. Lubricating Oil with Antifreeze Chemplex 710 Lubricant 1 lb. Lubricant 5 gram tube
Part No. 093500 Part No. 403720 Part No. 219090 Part No. 403734 Part No. 219188
Degreaser Cleaner Ideal cleaner for all Paslode tools.
Part No. 219086
Safety Glasses Clear Tinted
Part No. 402510 Part No. 402512
SAFETY INSTRUCTIONS
DO NOT EXCEED MAXIMUM RECOMMENDED AIR PRESSURE
WEAR EYE AND HEARING PROTECTION
60
0
120
60
120
0
Always wear hearing protection and eye protection devices, including side shields when operating or working in the vicinity of a tool.
Operate the tool using only the recommended air pressure. Do not exceed the maximum air pressure marked on the tool. Be sure the air pressure gauge is operating properly and check it at least twice a day.
Never use any bottled air or gases such as oxygen to operate the tool since they could cause the tool to explode.
P Printed in U.S.A. © 2003, Illinois Tool Works , Inc.
An Illinois Tool Works Company 888 Forest Edge Drive Vernon Hills 60061-3105
405680-10 08/03
