Transcript
WALL MOUNT DISPLAY INSTALLATION GUIDE
INSTALLATION TIME
1:00 hrs TOOLS REQUIRED q q q q q q q q q q
Electrical tape Measuring tape 4 mm hex key (allen wrench) 5 mm hex key (allen wrench) 6mm hex key (allen wrench) 3/16” hex key ( allen wrench Ratchet wrench Wire crimpers Wire stripper / cutter 9/16: Socket or wrench
12 Volt power is required to operate the display. If a power supply is desired a minimum of 25amp and 300watts is required to power the display.
AMP RESEARCH TECH SUPPORT 1-888-983-2204 (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST Designed and manufactured by AMP Research®. Patent Number 6,830,257; 6,641,158; 6,834,875; 6,938,909; 6,942,233; 7,007,961; 7,055,839; 7,163,221; 7,367,574; 7,380,807; 7,398,985; 7,413,204; 7,487,986; 7,566,064; 7,584,975; CA 2,463,717. Other US and Worldwide patents pending. Made in USA © 2010 AMP Research 5 -year limited warranty. Professional installation is recommended.
www.amp-research.com
/5
IM03771 rev 11.12.12
A M P R E S E A R C H P O W E R S T E P - WA L L M O U N T D I S P L AY
10-02641-14
19-03297-93
x2 16-02846-90
x2 19-03339-90
x2 16-03014-90
10-02624-14
x5 19-02805-90
19-03770-90L
x4 19-02485-90
x4 19-02989-90
x2 19-02845-90
x2 19-03302-90
x4 19-02802-90
19-03803-90 x8
x2 x4 x8
20-03752-42 www.amp-research.com
x2 /5
x2 IM03771 rev 11.12.12
A M P R E S E A R C H P O W E R S T E P - WA L L M O U N T D I S P L AY
Install motor to linkage using a 4mm hex key. Tighten to 36 in-lbs.
Using supplied 11” Zip ties mount controller to wall mount bracket.
Mount linkages onto wall mount bracket using a 6mm and 5mm hex key. LED light mount is to be bolted to bracket. Leave upper outside hole for mounting of the graphic display.
Set Wall mount bracket clips into slat wall.
Mount brackets to the wall. Use supplied acorn nuts. Do not tighten www.amp-research.com
Adjust wall mount distance so that the graphic display studs mount through the bracket holes. /5
IM03771 rev 11.12.12
A M P R E S E A R C H P O W E R S T E P - WA L L M O U N T D I S P L AY
Use supplied acorn nuts to tighten graphic to mounts
Tighten wall mount brackets using a 9/16” wrench..
Mount board to linkages and center between linkages. Use 3/16” Hex.
Route wire harness up through hole in bracket and connect into controller. www.amp-research.com
Install push button switch into hole in graphic.
Connect motor plug. /5
IM03771 rev 11.12.12
A M P R E S E A R C H P O W E R S T E P - WA L L M O U N T D I S P L AY
Adhere LED lights to light mounts. Secure wires with supplied zip ties
Route LED light wires out and across to LED light mounts.
Connect spade terminals to Push button. Secure wires with supplied zip ties.
www.amp-research.com
/5
IM03771 rev 11.12.12
