Transcript
Test & Measurement for Telco / IT / Electric
PROGRAM 2014/15
®
The Professionals in Test and Measurement Kurth Electronic is a leading manufacturer of test and measurement equipement for telecommunications, data systems and electrical installation. Over 30 years we develop and manufacture innovative and user-friendly devices that asist our worldwide clients in their daily work. ®
Products
Page
Broadband Multimedia Tester and xDSL Tester Introduction xDSL technology Comparison sheet xDSL Tester KE3600 KE3500 KE3400B Accessories
3 4 5 6 7 7
Line Qualification KE2500 KE2800
9 9
Electronic Remote Line Switching KE901 / KE905
11
Ethernet Performance Tester KE7500 KE7510 Accessories Applications
12 12 12 13
LAN & Ethernet Tester Comparison sheet LAN & Ethernet Tester KE7200 KE7100 KE6000 PoEcheck KE7010 Accessories Sets: KE6x01, KE710x, KE720x
14 15 15 15 17 17 17 18
Fiber Optic Testing KE8000 / KE8100 / KE8200 KE850 Sets: KE80xx Accessories
19 19 20 20
Cable & Line Tracer Comparison sheet Cable & Line Tracer / KE301 - KE2093 Applications Accessories
21 22 24
Buried Cable Path Locator Stick PLS 8879 PLS Accessories
25 25 25
Cable Conductor Test Set with Voice Connection TalkSet CCTS-03
27 27
Analog Test Telephone / ISDN P-MP Tester TP09D ICHECKplus
29 29
Cable Fault Meters KE-TDR06 KE-TDR20 KE-FLB KE-LQ20
30 30 30 30
Fiber
ADSL2+ ~6-25 Mb/s
Copper
High Speed Internet makes the availability of more and more increasing bandwidth in the data transmission absolutely necessary. In addition to the widespread ADSL technology over the copper pair, the expansion of VDSL2 is promoted especially in urban areas. VDSL allows higher bandwidths, but only over short distances. Another costly and therefore little used solution is e.g. the GPON or Dark Fiber technology. This fiber is not routed as used with VDSL2 up to the street cabinet (FTTC), but rather directly to the customer. Service providers use to optimize the existing VDSL ports to the Vectoring technology. This significantly increases the data transfer by eliminating the noise on the twisted pair. Even higher speed on the copper line is to be achieved with G.fast, in this case data rates up to 500 Mbit/s are possible. The use of new technologies, especially VDSL2 Vectoring, Bonding, G.fast and FTTH requires a new generation of test and measurement equipment. The innovative xDSL MULTITEST family does full Vectoring measurement, is prepared for DSL Bonding* and GPON* and can handle their testing tasks reliably in these environments without restrictions.
Ethernet Test
PON/PTB 200+ Mb/s
PC
PC VoIP
TV
xDSL Test
VoIP STB
Dark Fiber
TV
VDSL2 ~50 Mb/s
ADSL2+
STB
VDSL2 BONDING ~100 Mb/s
DSLAM/FTTN
DSL Bonding CENTRAL OFFICE PC
DSLAM/FTTN
VoIP
TV
FTTC FTTC
STB
VDSL2
PC
VDSL2 VECTORING ~100 Mb/s
VoIP
VDSL2 G.fast ~500 Mb/s
TV STB
VDSL2 VECTORING ~100 Mb/s
* KE3600 - future-proof modular technology
The Advantage: KE3600 and KE3500 MULTITEST Operating Concept
DSL LOSS
DSL L1
DSL L2
BATT CHRG
DSL DSL CRC LOSS
DSL L1
DSL L2
BATT CHRG
xDSL MULTITEST
DSL BATT CRC CHRG
DSL L2
KE3600
DSL L1
xDSL MULTITEST
BATT CHRG
DSL LOSS
KE3600
DSL L2
xDSL MULTITEST
DSL L1
KE3600
DSL LOSS
xDSL MULTITEST
DSL CRC
DSL CRC
KE3600
Broadband Multimedia Tester and xDSL Tester
New Broadband Technologies
Fast multi-tasking operating After a successful synchronization line values or graphs are shown on the large 3.5 " sunlight readable color display. Waiting periods or complicated and time-consuming switching between menu items and views belong to the past. The selection keys provide an easy exchange between the DSL line parameters, their impact on the application layers, results of Up/Download tests, Ping and Trace Route plus VoIP and IPTV parameters. The Multitester are likely to be used as a PC, with real multitasking functionality the user can scroll between the windows. Without the loss of the current synchronization, other parameters or tests can be added and thus enables fast, easy and comprehensive diagnosis.
KE-Manager Software included The supplied KE-Manager Software is a flexible tool to manage the KE3600 and KE3500, to download the measurements and for the creation of customized measurement reports. The surface is very clearly arranged and intuitive to use. Profiles can be easily created and edited in order to transfer them to the KE3600/KE3500. The optional Real Time Analysis function allows to transfer the current measurements from the tester to the Manager Software and look directly at the detailed test results on the PC. Extensive settings facilitates the evaluation of the results. The data can be stored and conveniently printed.
3
Broadband Multimedia Tester and xDSL Tester
n standard Annex
KE3400B xDSL TEST
– not available
ADSL-ADSL2+, Annex A/B/J/L/M
n
n
n
VDSL2 incl. Vectoring (ITU-T G993.5), Profiles 8a/b/c/d, 12 a/b, 17a
o
n
o (no Vectoring)
GbE-Port for HTTP and FTP Up/Downloadtests up to 700 MBit/s
n
n
–
DSLAM-Mode
–
–
n
VoIP
Triple Test: VoIP (terminal simulation)
o
o
–
IPTV
Triple Test: IPTV (Set Top Box emulation)
o
o
–
ISDN POTS
ISDN BRI S0-TE / POTS (telephonie, BERT, services, ...) speakerphone, hands-free conversations
o
o
–
Coppertests (Digitalmultimeter and xDSL Linequalifying up to 30 MHz)
o KECT
o KECT
o KECT1
TDR
TDR Measurements (fault location and length measurement)
o
o
n (with KECT1)
SFP
SFP-Gigabit- (fiber or copper) or GPON-SFP (ONT emulation)
o
–
–
xDSL Bonding (ITU-T G.998.1/2/3 Bonding, Bandplan 30)
o
–
–
SHDSL (2- / 4- / 8-wire interface)
o
–
–
ISDN S2M Primary-Multiplex interface
o
–
–
Future-proof modular technology
n
–
–
Multi-tasking tests (same time multiple tests without synchronization loss)
n
n
–
Rugged, water-resistant housing with protective case
n
n
n
High-performance LiPo battery for extended field-use
n
n
n
In the sunlight-readable color display
n (TFT)
n (TFT)
n (LCD)
PC software for measurement reports, power supply, test leads and pouch
n
n
n
A/B/J/L/M
DSL Vectoring
GbE
DSLAM
30 MHz
Copper Test
DSL Bonding
SHDSL
S2M
R
4
o optional available
KE3500 MULTITEST
KE3600 MULTITEST
Comparison sheet xDSL Tester
A/B/J/L/M
4
Vectoring
DSL Bonding
GbE
SHDSL
SFP Fiber/Copper
GPON
30 MHz
ISDN POTS
S2M
Copper Test
VoIP
IPTV
W
The "all-in-one" Solution for Broadband Measurement
Der KE3600 xDSL MULTITEST is a versatile and revolutionary xDSL tester of DSL services in ADSL1/2/2 + / VDSL2 (vectoring) and bundled networks and as well in FTTx deployments (GPON, Dark Fiber). With a variety of interfaces the outstanding KE3600 xDSL Multitester supports many access network technologies. Accelerated fault diagnosis is made possible by its simple operation even for untrained technicians. Interferences in the network, in the outdoor and inhouse cabling but also in CPE can be narrowed down quickly. Even in FTTH networks KE3600 carries out measurements at its Ethernet or built-in SFP Port. With the autodetect function of the DSL service no choice between ADSL and VDSL is necessary. Automated and editable measurements on the copper pair allows fast and efficient work. The universal SFP slot for measurements in FTTx deployments makes the KE3600 the ideal solution for these broadband technologies. The excellent price-performance and the guaranteed future security by the used module technology makes the KE3600 Multitester the perfect tool for all inspection tasks of current and future broadband technologies and sets standards in its class!
Options
VoIP Tests (see KE3500)
TDR Functions (see KE3500)
DSL L2
BATT CHRG
DSL CRC
DSL LOSS
DSL L1
DSL L2
BATT CHRG
DSL CRC
DSL LOSS
DSL L1
DSL L2
BATT CHRG
xDSL MULTITEST
ISDN S2M Primary-Multiplex-Interface n Extensive service query n Detailed information on the line status n BERT test (bit error rate)
Coppertests with KECT (see KE3500)
DSL L1
KE3600
xDSL Bonding n ADSL2+ and VDSL2 Bonding (ITU-T G.998.1/2/3)
IPTV Tests (see KE3500)
DSL LOSS
xDSL MULTITEST
GPON n GPON ONT, Modem emulation, GPON Software incl.
SHDSL 8 wire n Terminal-, Bridge- and Router-Mode n SHDSL up to symmetrical 5.7 MBit/s per pair n Ethernet First Mile (EFM/PTM) and ATM support n CO or DSLAM emulation (STU-C)
DSL CRC
KE3600
SFP: Copper/Fiber or GPON n SFP Copper (as second GbE-Port) or SFP Fiber n GPON: ONT, Modem emulation
xDSL MULTITEST
n New handheld tester with the most important interfaces n Intuitive multitasking operation n ADSL-VDSL2 and VDSL2-Vectoring (ITU-T G.993.5) in Annex A/B n Supports Annex A/B/J/L/M with DSLService Autodetection n GbE-Port, second SFP-Copper/Fiber or GPON-Port* n SHDSL 2-/4-/8-wire and S2M Interface* n Dial-in Test, Ping and Trace Route with IPv6 and IPv4 n Modem-, Router- and Terminal Mode shows all important parameters n FTP and HTTP Up/Download Tests up to 700 MBit/s n Large, sunlight readable color TFT with high resulution n LiPo battery and expandable memory n Including software for managing and creating protocols n Future-proof modular technology
ISDN/POTS Test Telephone n Speakerphone, hands-free conversations n Port and self-testing call n Extensive service query n Detailed information on the line status n BERT Test n Monitoring
KE3600
Benefits
*optional
5
VDSL
Annex
E N
Broadband Multimedia Tester and xDSL Tester
KE3600 xDSL MULTITEST
ADSL VDSL
No.
Type
Description
0.49830
KE3600
xDSL Multitester, 1 GbE Interface, ADSL 1/2/ 2+
0.49830-10
VDSL
Upgrade Firmware VDSL2 Annex A, B (Vectoring ITU-T G.993.5)
0.49830-12
KECT
Coppertest: xDSL Linie Qualification up to 30 MHz, DMM, integrated Remote Control Functions with KE900
0.49830-11
TDR
TDR up to 6 km
0.49830-25
ISDN
ISDN BRI S0-TE, UK0 (4B3T or 2B1Q) and POTS Interface
0.49830-5
VoIP
VoIP Tests (terminal simulation) Jitter, MOS, ...
0.49830-6
IPTV
IPTV Tests (Set Top Box emulation) Jitter, MOS, ...
0.49830-3
SFP-Port
SFP port for SFP-Copper or SFP-Fiber measurement plug-in.Supports e.g. a second GbE-Port or GPON option
0.49830-26
SHDSL
SHDSL 2-/4-/8-wire Interface
0.49830-7B
Bonding
DSL Bonding Module. Supports profiles 8a/b/c/d, 12a/b, 17a, 30a
0.49830-27
S2M
ISDN S2M Primary-Multiplex-Interface
Annex A/B/J/L/M
VDSL Vectoring
4
GbE
ISDN POTS
VoIP
IPTV
W
Full access to VDSL2-Vectoring and Triple Play Tests
The KE3500 xDSL MULTITEST offers tests in ADSL1/2/2 + and VDSL2 environments with full exams on VDSL-Vectoring. It performs other functions such as ISDN and POTS test telephone, Triple Play testing for IPTV and VoIP aptitude and the ability to do extensive copper testing to 30 MHz make it the universal working tool for installers and service technicians. With its innovative operation concept several tests are performed simultaneously and are still configurable without the loss of synchronization. Autodetection of the DSL service and automated measurements on the copper pair allow fast and efficient work. The user-friendly starting price in broadband measurement technology helps within the acquisition of the required instrumentation.s
Options
n GbE-Port n Dial-in Test, Ping and Trace Route with IPv6 and IPv4 n Modem-, Router- and Terminal Mode shows all important parameters
n Large, sunlight readable color TFT with high resulution n High performance LiPo battery and expandable memory n Including software for managing and creating protocols
ISDN/POTS Test Telephone n Speakerphone, hands-free conversations n Port and self-testing call n Extensive service query n Detailed information on the line status n BERT Test n Monitoring Coppertests with KECT n Prequalification of the copper lines: Impedance, Return Loss, Balance, NEXT Measurement, Receive Level and Spectrum, Wideband Noise and Impulse Noise n Digitale Multimeter Measurements for troubleshooting: Current, Voltage, Insulation, Resistance and Capacitance n The Loop Analysis summerizes the key measurements and automates the configurable measuremnt process n KE900 functions: sends switching commands to the optional Remote Unit KE905 directly for comfortable remote switching of copper pairs at the far end of the line TDR Functions (only in conjunction with KECT3) n TDR functions for precise fault detection and localisation (up to 6 km cable length with ø 0,5 mm)
DSL LOSS
DSL L1
BATT CHRG
DSL CRC
DSL LOSS
DSL L1
BATT CHRG
DSL CRC
DSL LOSS
DSL L1
BATT CHRG
xDSL MULTITEST
KE3500
xDSL MULTITEST DSL CRC
KE3500
n Supports Annex A/B/J/L/M with DSLService Autodetection
BATT CHRG
xDSL MULTITEST
n Intuitive operation and large, clear display
DSL L1
KE3500
n Basic equipment: ADSL-VDSL2 and VDSL2-Vectoring (ITU-T G.993.5) in Annex A/B
IPTV Tests n Set-Top-Box emulation n Review audio and video packets n Displays Bitrate and Packet Loss n Jitter, MOS n Preview function
DSL LOSS
xDSL MULTITEST
Benefits
DSL CRC
KE3500
VoIP Tests n Terminal simulation n VoIP connections via xDSL and Ethernet n VoIP signaling protocol SIP n Displays Bitrate, Packets and Packet Loss n Jitter, Jitter min/max n R-Value, MOS n Call setup both with and without a registrar / proxy
n FTP and HTTP Up/Download Tests up to 700 MBit/s
6
30 MHz
Copper Test
E N
Broadband Multimedia Tester and xDSL Tester
ADSL VDSL
KE3500 xDSL MULTITEST
No.
Type
Description
0.49810
KE3500
xDSL Multitester, 1 GbE Interface, ADSL 1/2/ 2+ and VDSL2 Vectoring
0.49810-12
KECT
Coppertest: xDSL Linie Qualification up to 30 MHz, DMM, integrated Remote Control Functions with KE900
0.49810-11
TDR
TDR up to 6 km
0.49810-25
ISDN
ISDN S0-TE, UK0 (4B3T or 2B1Q) and POTS Interface
0.49810-5
VoIP
VoIP Test (terminal simulation) Jitter, MOS, ...
0.49810-6
IPTV
IPTV Test (Set Top Box Emulation) Jitter, MOS, ...
0.49830-15
Real Time Analysis Enables Real Time Analysis (Live View) for evaluation of current running DSL services test in PC KE Manager software (MS WIN)
Broadband Multimedia Tester and xDSL Tester
ADSL VDSL
KE3400B xDSL Performance Tester
Annex A/B/J/M
Modem Router DSLAM
DrDSL ?
30 MHz
Copper
Test
The Universal Tester with DSLAM (xTU-C) und Coopertesting The KE3400B is the ideal tool for the prequalification, commissioning and troubleshooting on all ADSL and VDSL connections (even for the less experienced technician). In the standard version, it can be operated in the xDSL Modem mode, Router mode and even DSLAM mode (office emulation). This simplify tests procedures of the modem / router in house installations or in repairs.
SNR per tone graph gives back connection to sources of interference.
Options
Benefits n ADSL to VDSL2 in one unit n Annex A/B/J/L/M n Modem/Router and DSLAM Mode n IP-Ping Test, VLAN Identification n DSL-Lineparameter at a glance n High capacity battery for long term use n Test results storable, Software included Ready for n DrDSL Fault Interpretation Software n KECT1 Coppertest up to 30 MHz
Coppertests with KECT1 n Prequalification of the copper lines: Impedance, Return Loss, Balance, NEXT Measurement, Receive Level and Spectrum, Wideband Noise and Impulse Noise n Digitale Multimeter Measurements for troubleshooting: Current, Voltage, Insulation, Resistance and Capacitance n The Loop Analysis summerizes the key measurements and automates the measurement process n KE900 functions: sends switching commands to the optional Remote Unit KE905 directly for comfortable remote switching of copper pairs at the far end of the line n TDR functions for precise fault detection and localisation (up to 6 km cable length with ø 0,5 mm) DrDSL Fault InterpretationSoftware n This software helps users in plain text to detect existing errors, assess them and to eliminate them. DrDSL also indicates how the data rate would change after removal of the fault/interference source. Can be used in ATU-R and ATU-C mode. Detects defective AOD, bridge taps and other sources of interference and shows the possible change of the data rate.
No.
Type
Description
0.49820B
KE3400B
xDSL Performance Tester, ADSL 1 to ADSL 2+ Annex A/B/J/L/M, Software
0.49820-10
Upgrade
Upgrade Firmware VDSL2
0.49820-12
KECT1
30 MHz Coppertest Interface (in conjunction with new device)
0.49820-13
DrDSL
Fault Interpretation Software
0.49820-15
LiveView
Software LiveView for real time trace
0.49820-21
Storing
Software for continuous result storing
Accessories KE3600 / KE3500 / KE3400B For KE3600 / KE3500: Ear set including microphone and 3,5 mm phone jack. Internal loud speaker und microphone will be deactivated.
7
For KE3600 / KE3500 and KE3400B: Car charger 12 V 1,5 A
No.
Type
Description
0.49602
Earset
Earset with microphone and 3,5 mm phone jack for KE3600 and KE3500
0.49820-16
KFZ
Car charger 12 V 1,5 A
0.49620-10
KE900
Electronic Remote Line Switch
For KE3600 / KE3500 and KE3400B with Copper Interface: KE900 Electronic Remote Line Switch, see page 11.
KE3500 MULTITEST
KE3400B Performance Tester
Compliance ADSL1/2/2+
ITU-T G.992.5 (ADSL2+ incl. Annex A, B, J, M), ITU-T G.992.3 (ADSL2 incl. Annex A, B, J, L), ITU-T G.992.1 (G.DMT incl. Annex A, B, J) ATIS/ANSI T1.413 Issue 2 IEEE 802.3ah (PTM) ITU-T G.998.1/2/3 (Bonding)
ITU-T G.992.5 (ADSL2+ incl. Annex A, B, J, M), ITU-T G.992.3 (ADSL2 incl. Annex A, B, J, L), ITU-T G.992.1 (G.DMT incl. Annex A, B, J) ATIS/ANSI T1.413 Issue 2 IEEE 802.3ah (PTM)
ITU-T G.992.5 (ADSL2+ incl. Annex A, B, J, M), ITU-T G.992.3 (ADSL2 incl. Annex A, B, J), ITU-T G.992.1 (G.DMT incl. Annex A, B, J) ATIS/ANSI T1.413 Issue 2 IEEE 802.3ah (PTM)
VDSL2
ITU-T G.998.1/2/3 (Bonding with Profile 30a) ITU-T G.993.2 Annex A, B (Vectoring) Profiles: 8a/b/c/d, 12a/b, 17a Band Plan: 997, 998, US0 IEEE 802.3ah (PTM)
ITU-T G.993.2 Annex A, B (Vectoring) Profiles: 8a/b/c/d, 12a/b, 17a Band Plan: 997, 998, US0 IEEE 802.3ah (PTM)
ITU-T G.993.2 Annex A, B Profiles: 8a/b/c/d, 12a/b, 17a, 30a Band Plan: 997, 998, US0 IEEE 802.3ah (PTM)
DSL parameters
Maximum attainable bit rates Actual achieved bit rates Actual bonded achieved rates Latency modes: fast, interleaved Data modes: ATM, PTM Capacity (%) Signal-to-noise ratio (SNR) margin Output power Attenuation Bits/bin
Attenuation/bin (Hlog/bin), QLN/bin, SNR/bin Vendor code, revision Interleave depth Interleave delay INP G.INP Vectoring Modes: PTM, ATM LOS, FEC, CRC, HEC, LOF, LOM, SES, ES LATN per band, SATN per band
Maximum attainable bit rates Actual achieved bit rates Capacity (%) Signal-to-noise ratio (SNR) margin Output power, Attenuation Bits/bin, (Hlog/bin), QLN/bin, SNR/bin Vendor code, revision LOS, FEC, CRC, HEC; LOF, LPR, LPO LATN per band, SATN per band
Test interfaces
VDSL2, ADSL 1/2/2+ with autodetection Ethernet 10/100 Ethernet 10/100/1000
Encapsulation
RFC 2684 supporting bridged Ethernet (IPoE), IPoA (RFC 1577), PPPoE (RFC 2516), PPPoA/LLC and PPPoA/VC-MUX (RFC 2364)
Modes
DSL Terminal-, Router- and Modem-Mode Modem replacement (DSL to Ethernet) Ethernet Terminal Mode
Login format
Username and password using PAP/CHAP
Connectivity support
LAN/WAN status DNS, gateway DHCP client/server, DHCP vendor class NAT
Ping test*
Ping destination: Gateway, IP-Address or URL Number of Pings: 1 to 99 Packet size: 32 to 1200 Bytes (default is 32) Timeout: 1 to 10 seconds Results: Packets sent/received, average round-trip delay (ms)
Trace Route test*
Traceroute destination: Gateway, IP-Address or URL * Run any number of Timeout: in seconds, default is 1 s, maximum is 10 s tests simultaneously Packetsize: 32 Bytes Number of hops: 1to 32 (default is 30) Results: Indicates IP address of hop and round trip time in milliseconds (ms)
FTP/HTTPspeed tests*
Address: IP or URL Direction: Upload and/or Download up to 700 MBit/s Results: Timet, kB transferred, speed in kBit/s Bookmarks: User-definable
Software options
IPTV Test (Set Top Box emulation) Jitter, MOS,... VoIP Test (terminal simulation) Jitter, MOS,...
IPTV Test (Set Top Box emulation) Jitter, MOS,... VoIP Test (terminal simulation) Jitter, MOS,...
DrDSL fault interpretation software
Interface options
xDSL Bonding-Moduel* SHDSL 8 wire interface* KECT3 copperqualifying up to 30 MHz with DMM TDR error detection / localization SFP-Port for copper, fiber (second GbE-Port) or GPON (ONT), Transceiver optional* ISDN BRI Uk0 / S0 / POTS interface ISDN PRI S2M Interface*
KECT3 copperqualifying up to 30 MHz with DMM TDR error detection / localization ISDN BRI Uk0 / S0 / POTS interface
KECT1 coppertest interface: Qualifying up to 30 MHz with DMM and TDR
Display
3,5" TFT Display, RGB 240 x 320
Power supply
LiPo battery with approximately 4 hours operation at full load mode
Dimensions
230 x 110/90 x 70 mm
Weight
820 g
Housing
Impact-resistant ABS case with protective and high impact plexiglass as display cover
Menu languages
G, E, F, IT, NL
VDSL2, ADSL 1/2/2+ Ethernet 10/100
DSL Terminal-Mode Modem replacement (DSL to Ethernet) DSLAM Terminal Mode (xTU-C)
VLAN ID, VLAN tagging VPI/VCI IP release Signal Strength
VLAN ID, VLAN tagging VPI/VCI IP release Signal Strength *Run any number of tests simultaneously
Results: Packets sent/received, average roundtrip delay (ms)
* Run any number of tests simultaneously
3" LCD Display with backlight, 64 x 128
800 g
740 g
G, E, F, IT, ES, POR, NL
*More information and availability on request
Broadband Multimedia Tester and xDSL Tester 8
KE3600 MULTITEST
E N W
Telco Qualifier and Telco Multimeter
DMM Copper
KE2500 Telco Multimeter Telco Multimeter for telecommunication applications
The KE2500 Telco Multimeter is designed specifically for telephone 2-wire lines and allows a detailed error analysis and a complete overview of the physical state of the circuit under test. The tester stands out with its handy and robust design. The optional KE900 for remote switching of the line to be tested increases the effectiveness and ease of use by a multiple.
Benefits n n n n n
Measurement of symmetry, resistance, capacitance Loop analysis: automated test sequences simplify and speed up measurements TRMS, AC/DC current and voltage Insulation measurement with 8 V or 100 V Direct control commands for optional KE905 Remote unit for remote switching of the copper pair n Analysis of signature + PPA (Telekom) n Storage of measured data and transfer via USB port
No.
Type
Description
0.49250
KE2500
Telco Multimeter with USB-Connection for Data transfer, test leads, pouch
0.49620-10
KE905
Electronic Remote Line Switch with test leads
Copper 30 MHz
KE2800 Telco Qualifier
for ADSLVDSL2
DMM
TDR
The most important advantage of xDSL is the elimination of the cost of installing new cables. The approved maximum cable length and the maximum achievable data transmission speed will depend on the characteristics of the cable. Before installing a xDSL modem should therefore be checked whether the properties and quality of the selected pair of wires correspond to the requirements of the intended application for the system. The KE2800 Telco Loop Qualifier fault analysis in the direct current and alternatingcurrent range with Digital Multimeter functions, TDR Cable Fault Location and measurements up to 30 MHz.
Benefits n Impedanz, Return Loss, Balance, NEXT Measurement, Receive Level, Spectrum, Wideband Noise and Impulse Noise n Symmetry, resistance, capacitance n Loop analysis: automated test sequences simplify and speed up measurements n TRMS, AC/DC current and voltage n Insulation measurement with 8 V or 100 V n TDR shows and locates cable faults n Storage of measurement data, USB transfer n Direct control commands for optional KE905 Remote unit for remote switching
9
No.
Type
Description
0.49280
KE2800
Telco Loop Qualifier, test leads, pouch
0.49620-10
KE905
Electronic Remote Line Switch with test leads
W
E
N
Telco Line Qualification up to 30 MHz
Telco Qualifier and Telco Multimeter / KECT Copper Interface
KE2500 / KE2800 / optional KECT Copper interface with KE3500 / KE3600 Voltage
Measuring range Maximum voltage Input impedance Resolution output 6 V / 60 V / 200 V Accuracy DC / AC Overload
≤ 1 mV to 200 V (AC, DC) ≤ 300 V > 9 MΩ DC, > 9 MΩ II <50 pF AC 1 mV / 10 mV / 100 mV 0,5 % / 1,5 % 300 V AC/DC Sinus, constant
Current
Measuring range Maximum voltage Accuracy DC / AC2 Overload
≤ 0,1 mA to ≥ 500 mA (AC, DC) ≤ 950 mA 0,5 % / 1,5 % 0,95 A, shutdown1
Resistance
Measuring range Resolution at 3 kΩ Measuring current 3kΩ Accuracy Overload
0 to 3 kΩ 100 mΩ 2 bis 6 mA / < 33 V ± 0,5 % + 0,5 Ω 300 V AC/DC Sinus, shutdown1
Insulation
Measuring range Resolution at 30 MΩ / 300 MΩ / 3 GΩ Test voltage Accuracy Overload
to 2 GΩ 10 kΩ / 100 kΩ / 10 MΩ 100 V, 8 V 100 V: ± 2 % - ± 5 Digit / 8 V: ± 2 % - ± 10 Digit 300 V AC/DC Sinus, shutdown1
Capacity
Measuring range Input impedance at 30 nF / 300 nF / 3 µF Resolution at 30 nF / 300 nF / 3 µF Accuracy at 30 nF / 300 nF / 3 µF Overload
30 nF to 3 µF < 33 Vss 10 pF / 100 pF / 1 nF 1 % + 100 pF / 1 % + 500 pF / 1,5 % + 5 nF 300 V AC/DC Sinus, shutdown1
1 2
Overload: Switch over to voltage measurement. Measurements are not possible via a current clamp. The TRMS converter produces a zero error in the AC measurements of up to 30 digits.
RF Measurement
KE2800 / optional KECT Copper interface with KE3500 / KE3600
Impedance
Receive frequency Input impedance Readout Resolution output Accuracy
4 kHz to 30 MHz 100 S, 120 S S, graphic 0,1 S ± 5 % resp. ± 5 S
Return Loss
Receive frequency Input impedance Readout Resolution output Accuracy
4 kHz to 30 MHz 100 S, 120 S dB, graphic 0,01 dB ± 1 dB
Balance
Receive frequency Input impedance Readout Resolution output Accuracy to 2 MHz / to 10 MHz / to 30 MHz
4 kHz to 30 MHz ± 0,5 %, 120 S dB, graphic 0,01 dB ± 0,5 dB / ± 2 dB / ± 5 dB
NEXT
Receive frequency Input impedance Readout Resolution output Accuracy
4 kHz to 30 MHz 100 S, 120 S dB, graphic 0,01 dB ± 0,5 dB
Receive Level
Receive frequency Input impedance Readout Resolution output Accuracy
4 kHz to 30 MHz 100 S, 120 S, high impedance dBm, graphic 0,01 dBm ± 1 dBm
Spectrum
Receive frequency Input impedance Readout Resolution output Accuracy
4 kHz to 30 MHz 100 S, 120 S, high impedance dBm or dBm/Hz, graphic 0,01 dBm resp. 0,01 dBm/Hz ± 1 dBm
Wideband Noise
Receive frequency Input impedance Filter Readout Resolution output Accuracy
4 kHz to 30 MHz 100 S, 120 S ADSL 1,1 MHz, ADSL+ 2,2 MHz, VDSL1 12 MHz, VDSL2-8 8,5 MHz, VDSL2-12 12 MHz, VDSL2-17 17 MHz, VDSL2-30 30 MHz dBm, nummeric 0,01 dBm ± 1 dBm
Pulse duration Input impedance Threshold Resolution output Other output values
> 500 µs 100 S, 120 S 0,1 mV to 25,4 mV / 20 to 59,9 dB 0,1 mV / 0,1 dB Runtime in seconds and number of noise pulses
Impulse Noise
TDR-Function* Time Domain Reflectometer *optional with KE3500/KE3600
10
Measuring range Measurement resolution Pulse Analog gain Resolution output Zoom
8 m to 6.000 m 6,26 ns 12,5 ms to 2500 ms 0 dB to 56 dB in 10 dB steps 0,1 m Maximum 10 x
for ADSLVDSL2
The KE901 Loop Test Assistant for remote switching reduces the cost of traveling from the customer returning to the office or the distribution to make changes. This will save your time and thus labor costs. The customer line remains in service while driving. There is no influencing of the lines up to 30 MHz.
Benefits n Turn of bridges and switching lines from the distance n 3 pairs of wires or instruments can be connected n Customers line remains in service until the measurement starts n Remote switching up to 12 km are possible n Switching functions are acknowledged acoustically and visually n Supports and works with any tester - regardless of the manufacturer n KE905: Direct control commands from KE2500/KE2800 and the xDSL Tester with KECT coppertest interface
APPLICATIONS KE900 WITH KECT/KE2500/KE2800 CCC
MDF
CUSTOMER er
BATT CHRG
DSL LOSS
DSL L1
DSL L2
orm
ance
test
DSL CRC
00
xDS
L perf
®
KE36
Electronic Remote Line Switching
Copper 30 MHz
KE901 / KE905 Loop Test Assistant
00 KE9 te o Rem
F4
F3
F2
F1
SEL
ESC ON OFF
3
2
1
DEF
ABC
6
5
4GHI
MNO
JKL
9
8
7
WXYZ
TUV
#
PQRS
0
*
Slave
Master
Master-Slave measurement: Can be used to measure the attenuation with an additional signal transmitter so Port 1 is connected to Port 3
er
BATT CHRG
DSL LOSS
DSL L1
BATT CHRG
DSL L2
er
test
DSL CRC
test
DSL CRC
DSL L1
DSL L2
orm L perf
®
xDS
xDS
00
KE36
00
KE36
00 KE9 te o Rem
DSL LOSS
ance
ance orm L perf
®
F4
F3
F2
F1
SEL
ON OFF
SEL
DEF ON OFF
ABC
6
5
4GHI
F4
ESC
3
2
1
F3
F2
F1
ESC
9
8
7
*
0
3
DEF
ABC
#
6
5
4GHI
WXYZ
TUV
PQRS
2
1
MNO
JKL
Cut through: Customers line remains in service up for the start of the measurement, the customer can continue working. Open: Measuring e.g. Noise, Capacity, Voltage, Insulation, etc.
MNO
JKL
9
8 TUV
7
WXYZ
#
PQRS
0
*
er
BATT CHRG
DSL LOSS
DSL L1
DSL L2
orm
ance
test
DSL CRC
KE36
00
xDS
L perf
®
00 KE9 te o Rem
F4
F3
F2
F1
SEL
ESC ON OFF
3
2
1
DEF
ABC
6
5
4GHI
MNO
JKL
9
8
7
WXYZ
TUV
PQRS
*
11
Bonding preperation: This configuration alowes to measure two independent loops for influence to each other
0
#
KE905 Remote
KE910 Controller
Housing
n Heavy duty ABS plastic weather-resistant design n Battery cover equipped with captive screws n 4 test cord receptacles for alligator-to-TF cords n Resistant Mylar front foil with short operation
n Heavy duty ABS plastic weather-resistant design n With silicone rubber control keys n Battery cover equipped with captive screws
Test cords
2 special test cords for testing up to 30 MHz Insertion loss: 0 - 30 MHz < 0,5 dB Crosstalk: -78 - -56 dB
n Insulated test leads with banana plugs n Modified DTMF control signals n Sample function min. 56 dB amplification
Power source
9 V Alkaline battery, typical life 200 h
9 V Alkaline battery, typical life 40 h
Overvoltage Protection
up to 160 V AC/DC
up to 160 V AC/DC
Dimensions
160 x 95 x 35 mm
150 x 65 x 26 mm
Weight
290 g with battery
95 g with battery
No.
Type
Description
0.49620
KE901
KE900 Remote + KE910 Control, test leads, pouch
0.49620-10
KE905
KE905 Remote to use with KECT1, KECT3, KE2500 and KE2800
MPLS
SAM
SFP
E N
Ethernet Performance Tester
RFC 2544
KE7500 GIGATEST
W
Gigabit Dual-Port Tester for Copper and Fiber
The KE7500 GIGATEST is an easy-to-use and cost-effective test solution for Carrier Ethernet Services and for Ethernet Network installation. The dual-port 10/100/1000 Mbit/s for copper and fiberoptic networks allows cable tests at the physical layer and traffic analysis at layer 2 and 3 including RFC2544 tests and Y.1564-service testing. With the rugged device technicians can implement commissioning of Ethernet and IP services. Performance values in numerical and graphical forms are displayed on the large 3.5 " TFT color screen quickly and clearly. The handy tester is designed for technicians who are looking for a versatile and easy-to-use solution. With software options further test functions such as Multistream Measurements and Synchronization to PTP IEEE1588 can be added. Optional SFP modules support all measurements of the KE7500 in Gigabit Ethernet Networks.
Benefits n n n n n n n n n n
Dual Port 10/100/1000 MBit/s Copper- and Fiber interface for Carrier Ethernet Services RFC2544 Performance testing Ethernet Service Activation Methodology (SAM) Tests Y.1564 Up to 10 configurable Multistreams Supporting MPLS, OAM and ARP Layer 1 - 4 Loopback Function End-to-End Analysis Optical power measurement (GbE-SFP) Mediaconverter Documentation with included PC software
No.
Type
Description
0.49430
KE7500
Dual Port Ethernet Carrier Tester, 10/100/1000 Base-T (RJ45) and 1000 Base-FX (SFP), software, pouch
0.49430-10
KE7500 SAM
Software Option: SAM Service Activation Methodology Test (Y.1564)
0.49430-11
KE7500 MS
Software Option: SimultaneousMultistream measurements
0.49430-12
KE7500 MPLS
Software Option: MPLS packet field configuration
0.49430-13
KE7500 PTP
Software Option: Synchronization measurement according PTP IEEE1588
0.49430-14
KE7500 RC
Software Option: Remote Control Manangement via Ethernet
KE7510 Loopback Remote W
E
N
KE7510 Remote Loopback is the ideal tool for the maintenance of Ethernet networks up to 1 Gbit/s with SFP-Port capability.The compact loopback tool can be used as a remote unit to retransmit test traffic, enabling service providers to turn-up and install Carrier Ethernet Service connections and to perform analysis tests.
Benefits n Basic Loopback Unit for Layer 1- 4 n Supports: OAM, ARP, DHCP, MPLS n Optional Analyze Test Software Type
Description
0.49435
KE7510
GIGATEST Remote: Ethernet loopback device
0.49435-10
AT
Analyze Option Tool for end-to-end measurements
No.
Accessories
12
SFP Transceiver
Test cable SMF
Test cable MMF
Plug-in for Gigabit-Ethernet
2 m, Duplex
2 m, Duplex
SFP-RJ No. 0.57102 10/100/1000 Base-T with RJ45
LC/PC - LC/PC No. 0.57110
LC/PC - LC/PC No. 0.57114
LC - LC (plastic) Duplex No. 0.57125
SFP-850 No. 0.57103 1000 Base-SX with DDM, 850 nm MMF, LC
LC/PC - SC/PC No. 0.57111
LC/PC - SC/PC No. 0.57115
SC - SC (plastic) Duplex No. 0.57126
SFP-1310 No. 0.57104 1000 Base-LX with DDM, 1310 nm SMF, LC
LC/PC - FC/PC No. 0.57112
LC/PC - FC/PC No. 0.57116
FC - FC (metallic) Simplex No. 0.57127
SFP-1550 No. 0.57105 1000 Base-SX with DDM, 1550 nm SMF, LC
LC/PC - ST/PC No. 0.57113
LC/PC - ST/PC No. 0.57117
ST - ST (metallic) Simplex No. 0.57128
Coppler
Statistics
Network
5
ETH-Port A TEST
RX
TX
Loop Layer
2
KE7500 with multistream test load generation and packet delay variation (IEEE1588)
RX
TX
3
KE7500 in statistics collection and user traffic parameters checkout mode
4
KE7510 Loopback Remote in loopback mode
5
KE7510 Loopback Remote in test traffic generation mode as an active load test data generator
6
Remote control of the tool via USB interface and control other KE7500 via Ethernet Management Port
LINK
®
Speed
F3
F2
F1
On/Off
KE7500 in 2 channels testing mode and loopback at the far end
ETH-Port B TEST
LINK
KE7500
Loop Layer
Speed
1
3
4
GIGATEST
RFC2544
F4 SEL
ESC
KE7510 REMOTE ON OFF
2
1
On/Off
ABC
5
4
GHI
KE7510 REMOTE
JKL
8
7
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Loopback RFC2544 ETH-Port A RX
TX
LINK
TEST
GIGATEST
RX
TX
LINK
®
PDV Test
Web F3
F2
F1
F4
ETH-Port A
SEL
ESC
ON OFF
1 4
GHI
7
2
ABC
5
JKL
8
3
6
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
2
TEST
RX
TX
Remote Control
TEST
RX
TX
LINK
®
F3
F2
F1
USB
ETH-Port B LINK
GIGATEST
TEST
BERT
ETH-Port B
KE7500
1 KE7500
Ethernet Performance Tester 13
KE7500/KE7510 Applications
F4 SEL
ESC
ON OFF
1 4
GHI
7
2 ABC 5
JKL
8
3
DEF
6
MNO
9
PQRS
TUV
WXYZ
*
0
#
Loopback
KE7500 GIGATEST
KE7510 Loopback Remote
Tests
n RFC2544: Throughput, back-to-back, frame-loss and latency measurem. n OAM-Protocol (Operation, Administration and Maintenance) n Cable Diagnostic n ARP&RARP, DHCP, MPLS, PDV (Packet jitter), PTP confirming IEEE1588 n BERT
n Layer 1 - 4 Loopback Function n End-to-end tests with analyze tool option
Connections
2 x RJ45 10/100/100 BASE-T (to Gigabit Ethernet) 2 x SFP 1000 BASE-x (Fiber Gigabit Ethernet) 1 x RJ45 10/100 BASE-T (Management Port) 1 x USB (Firmware Upgrade and Remote Control)
1 x RJ45 10/100/100 BASE-T (to Gigabit Ethernet) 1 x SFP 1000 BASE-x (Fiber Gigabit Ethernet) 1 x RJ45 10/100 BASE-T (Management Port) 1 x USB (Firmware Upgrade and Remote Control)
Housing
Rugged and water resistant ABS housing
Rugged and water resistant ABS housing
Display
3.5" TFT color display, cover made of high impact-resistant plexiglass
-
Power Supply
Built-in rechargeable LiPo battery
Dimensions
225 x 110/80 x 40 mm
160 x 95 x 35 mm
Weight
650 g
280 g
Languages
German and English
-
Test reports
Tests specified in the service-level agreement (SLA). Graphic and tabulated reports generated according to test results can be transferred to PC
-
LAN & Ethernet Tester
Comparison sheet LAN & Ethernet Tester
KE7100
Easy to read display with a clear view of the cable status
n
n
n
Checks wiring for continuity, open, short circuit, reversal, screen
n
n
n
Shock-proof, stable housing
n
n
n
Check the wiring with PIN and pair assignment (wire map) starting from one pair
n
n
–
Measurement of line length and distance to fault up to 150 meters (TDR function)
n
n
–
16 predefined profiles of wiring and cable types, custom profiles are editable in the unit
n
n
–
SPLIT PAIR
Detecting split pair errors
n
n
–
PoE
PoE test with display of the available power IEEE802.3af and IEEE802.3at
n
n
–
Port identification with link-blink function and sending search tones (with optional Probe)
n
n
–
Up to 32 active remote units configurable / supplied quantity
n/2
n/1
–
Active Network Test with Static IP or DHCP as well as 10/100/1000 Mbit/s detection
n
–
–
Network scan with a list of participants with their name, IP and MAC address
n
–
–
Ping of individual addresses, PING with packet loss indication / response times for stress test
n
–
–
Saves cable tests and network information, and allows for individual measurement protocols
n
–
–
Optional: Bridge Tap Detection for 2-wire lines (4-5)
o
–
–
Quality: Made in Germany
n
n
–
0.49420
0.49410
123456780 312456780
TDR
Ping xxx.xxx.xx
Bridge Tap in Made ny Germa
No.
14
KE6000
KE7200
n standard
o optional available
– not available
0.49400
LAN & Ethernet Tester
KE7200 Ethernet Tester
TDR
Ping
PoE
xxx.xxx.xx
The KE7200 Ethernet Performance Tester is the ideal tool during commissioning tests, troubleshooting and documentation of data- and telecommunication networks up from 1 pair with outstanding price-performance ratio. Versatile functions, the large graphical display and intuitive controls allow the user to work efficiently.
Benefits n Checks for continuity, short, open, reversal, split pair, screen n Built-in and editable cable database n Cable length measurement (TDR) n Length to the error (Open / Short) n Power over Ethernet load test (IEEE802.3af) n NEW: Also PoE load test after IEEE802.3at n Detects active network participants (name / IP / MAC) n Ping-stress test in 10/100/1000 Mbit / s networks n Trace tone mode and Port Finder function n Applicable with up to 32 Remote Units KE7010 n Stores cable tests and network information n Includes software for individual protocols n Detects branches / stubs (optional)
KE7200 Ethernet performance tester Recognizing the network participants
Description Ethernet Performance Tester with 2 Remote Units KE7010, PC software, test leads, pouch
No.
Type
0.49420
KE7200
0.49421
KE7200 PRO Kit Ethernet Performance Tester with 4 Remote Units KE7010, Probe310, PC software, test leads, pouch
TDR
KE7100 Ethernet & LAN Tester
PoE
The KE7100 LANcheck is an easy-to-use, handy and cost-effective LAN tester. The little brother of the KE7200 Ethernet Performance Tester is ideal for measurements in data- and telecommunication networks up from 1 pair where no documentation is required.
Benefits n Checks for continuity, short, open, reversal, split pair, screen n Built-in and editable cable database n Graphical Display n Cable length measurement (TDR) n Length to the error (Open / Short) n Power over Ethernet load test (IEEE802.3af) n NEW: Also PoE load test after IEEE802.3at n Trace tone mode and Port Finder function n Applicable with up to 32 Remote Units KE7010
No.
Type
0.49410
KE7100 LAN Tester with 1 Remote Unit KE7010, test leads, pouch
KE7100
LANCHECK
Clear display of wiring faults
Description
KE6000 Network Cable Tester
123456780 123456780
The handy KE6000 helps you quickly and easily during testing of patch cables, LAN and telecommunications cabling.
Benefits n n n n n
15
RJ11/RJ45/Coax Clear display shows status of the cable Checks for continuity / short / open / reversal / screen / multiple errors Error display on both sides saves time For testing in installations 2 x KE6000 will be needed
No.
Type
Description
0.49450
KE6001
LAN Cable Tester Kit of 2 x KE6000, batteries and carrying case
0.49400
KE6000
LAN Cable Tester with LCD-Display
LAN & Ethernet Tester
KE7200 Wire test copperr
n n n n n n
Power over Ethernet Test
n Activation of PoE Port n Measuring of voltage and current. Shows available power in Watts (IEEE802.3af and IEEE802.3at)
IP Networktests
n Checks Network with static IP or by DHCP n Detects the network speed 10/100/1000 MBit/s n IP address and MAC address settable n Listing of all working stations by name, IP and MAC address n Ping of selected addresses - frame settable between 32 and 1024 Bit n Shows result number of Pings, lost Pings, time min/max/average n Constant Ping mode to generate traffic
Port Identification and Cable Trace
n Hub-Link Blink function n Trace tone to be detected by capacitive Probe (optional with PROBE310) n 4 tones selectable
Bridge Tap (optional)
n Detects and locates Bridge Taps
n/a
KE7200 / KE7100
KE7010 Remote Unit
Features
see above
n ID programmable 01 - 32 n LED shows good/bad
Over voltage protection
up to 100 Volt
up to 100 Volt
Housing
solid and weather protected ABS with drop protection
solid and weather protected ABS
Power supply
4 x 1,5 V Alkaline battery > 40 h lifetime
–
Dimensions
195 x 100/78 x 45 mm
61 x 41 x 26 mm
Weight
380 g without batteries
30 g
Environment
Operation temperature -5° – +50°C Storage temperature -25° – +75°C Humidity 90% non-condensing
Menu language
German and English
Check of wires connected to PIN and pair Detects Split Pair from 2 m on 16 dedicated wiring schemes predefined, user settabel via device Cable types with 7 predefined VP values, user settable via device Graphical display shows wire map with clear indication good/bad Measures all wires seperatly and shows length to fault short/open up to 150 m
KE6000
16
KE7100
Cabel types
UTP 4-wire, STP, FTP, 568A, 568B, USOC, Coax
Fault detection
Short, open, continuity, reversals, shield faults, multiple faults
Cable length
max. 330 m
Power Supply
3 x AAA batteries
Batt. lifetime
up to 50 h
Dimensions
103 x 79 x 27,5 mm without bumper
Weight
85 g without batteries
Operation temperature
0° up to 40°C
n/a
–
LAN & Ethernet Tester
Power over Ethernet Tester The POEcheck is a small tester with easy and fast determination whether the port is PoE powered and if so, what system (type A or B) of the standard IEEE 802.3af. Just plug in the device leading to the patch cable into the POEcheck or connect the POEcheck with the supplied test leads with the data socket and immediately displays whether the supply voltage is supplied and in what version.
Benefits n Fast display of the supply variant n Lightweight, compact and inexpensive
No.
Type
Description
0.49460
POEcheck
Power over Ethernet Tester with test leads and RJ45 jack
7010 Remote Unit KE7010 Remote Unit to use with KE7100 and KE7200
Benefits n Info LED for OK / not OK n Remote number individual programmable
No.
Type
Description
0.49415
KE7010
Remote Unit, Remote Number individual programmable
KE7010 Kit: Set of 4 Remote Units and pouch for KE7100 and KE7200 No.
Type
Description
0.49416
KE7010 Kit
4 Remote Units, pouch
KE7010 PRO Kit: Set of 4 Remote Units, search signal receiver Probe310 and pouch for KE7100 and KE7200
Accessories
No.
Type
0.49417
KE7010 PRO Kit 4 Remote Units, Probe310, pouch
No.
Type
No.
Type
0.57605
Carrying case
0.57613
Protective pouch
Carrying case, blue with Kurth Electronic print Suitable for cable locator kit and / or Network Tester Kit
17
Description
Protective bag with equipment and cable tray Fits KE7100, including strap
LAN & Ethernet Tester
KE6301 - KE6801 Cable Finder & LAN-Tester Set
SET
Enable the line search and identification of pairs and the review of network and telecommunication cable routes. Set of Cable Finder Kit and two KE6000 cabling testers including batteries, in impact-resistant plastic case.
Benefit n n n n
Fast testing of wiring Only one technician required to check Ideal for new construction and repair With a Cable Finder Kit KE301 to KE801
Type
No. 0.49450-3
Description KE6301 Cable Finder and LAN Test Kit, consisting of KE301 Classic and 2 x KE6000, batteries, case
0.49450-5
KE6401 Cable Finder and LAN Test Kit, consisting of KE401 IT and 2 x KE6000, batteries, case KE6501 Cable Finder and LAN Test Kit, consisting of KE501 Electric and 2 x KE6000, batteries, case
0.49450-7
KE6701 Cable Finder and LAN Test Kit, consisting of KE701 Telco and 2 x KE6000, batteries, case
0.49450-8
KE6801 Cable Finder and LAN Test Kit, consisting of KE801 Copper & Fiber and 2 x KE6000, batteries, case
0.49450-4
KE7107 - KE7108 Network Test Sets
SET
The ideal set for working in telephone and data networks consisting of network tester and cable locator kit. Provide time and cost saving and simplify installation and troubleshooting.
Benefits n n n n n n n
Checks the network wiring TDR length measurement up to 150 m Integrated, configurable cable database Power over Ethernet load test KE701/KE801 find cables and wires KE801 with fiber optic continuity tester In sturdy plastic case with batteries
Type Description 0.49451-7 KE7107 KE7100 LANcheck, 1 x KE7010, KE701 Telco, test leads, batteries, case No.
0.49451-8 KE7108 KE7100 LANcheck, 1 x KE7010, KE801 Copper & Fiber, test leads, batteries, case
KE7207 - 7208 Professional Network Test Sets
SET
Professional set for installation and troubleshooting with the ability to create individual measurement protocols. The perfect solution for efficient work in active and passive networks.
Benefits n n n n n n n n n n n
Checks the network wiring TDR length measurement up to 150 m Integrated, configurable cable database Detection of 10/100/1000 Mbit / s networks Network scanning and ping-stress test Power over Ethernet load test Stores cable tests and network information Incl. Software for individual log creation KE701/KE801 find cables and wires KE801 with fiber optic continuity tester In sturdy plastic case with batteries
Type Description No. 0.49452-7 KE7207 KE7200 Ethernet Performance Tester, 2 x KE7010, KE701 Telco, test leads, batteries, case 0.49452-8 KE7208 KE7200 Ethernet Performance Tester, 2 x KE7010, KE801 Copper & Fiber, test leads, batteries, case
18
Multi Mode
W
KE8000 / KE8100 / KE8200 are inexpensive and easy-to-use optical power meter and light sources in pocket format for attenuation measurement during installation and maintenance of optical single- and multimode networks.
SC
E N
Fiber Optic Testing
Single Mode
KE8000 / KE8100 / KE8200
Benefits n n n n n n n
Fiber type
Optical power meter with six calibrated wavelengths Measuring range from -70 to +10 dBm Optical light source for single mode 1310, 1490 and 1550 nm Multimode light source with two wavelengths 2.4 "LCD with backlight SC measuring adapter in the basic configuration Rugged, handy and easy to use
KE8000 Optical Power Meter
KE8100 MM Light Source
KE8200 SM Light Source
Multimode, Singlemode
Multimode (62,5/125 µm)
Singlemode (9/125 µm) 1310, 1490, 1550 nm
Wavelength range in nm
800 up to 1700 nm
850, 1300 nm
Calibrated wavelengths in nm
850, 1300, 1310, 1490, 1550, 1625
–
Variably measuring adapter system
SC/PC, FC/PC and ST/PC
SC/PC,
Detector / transmitter diode
InGaAs
FP laser diode
Measurement range
-70 ... + 10 dBm
–
Measurement accuracy
±5%
–
Power / attenuation measurement
in dBm or µW / dB
–
Output level
–
> -10 dBm (Class I)
DFB laser diode
> - 7 dBm (Class I)
Level stability
–
< 0,05 dB/5 h; < 0,1 dB/15 min
Modulation
automatic detection
continuous wave and modulation: 270 Hz, 330 Hz, 1 kHz, 2 kHz
Power supply
2 x AA Alkaline batteries
2 x AA Alkaline batteries
Operating time
> 70 h with Auto-OFF function
> 15 h with Auto-OFF function
Display with backlight
2.4" LCD
2.4" LCD
Operating temperature
-10° C ... + 50° C
-10° C ... + 40° C
Dimensions
160 x 76 x 28 mm
160 x 76 x 28 mm
Weight
210 g
220 g
Standard accessory
Measuring device with protective bag, batteries, calibration certificate and instruction manual
No.
0.49110
0.49120
0.49130
KE850 Fiber Optic Fault Locator
n For optical LAN and telecom networks n Detect fibers in fiber bundles, testing of fibers for break, bend and throughput n Continuous light and Pulse mode
Wavelength
19
650 nm, Laser Protection Class II
Operating modes
Continuous Wave (CW) and Pulse Mode, Frequency 2 - 3 Hz
Measuring adapter
2,5 mm DIN: E2000,FC, SC, ST
Power supply / Operating time
2 x AAA Alkaline batteries / 40 h in Pulse Mode
Dimensions / Weight
ø 12,1 mm, Length 156 mm / 70 g with batteries
No. / Standard accessory
0.49100 / with protective case, batteries, instruction manual
W E
Benefits
N
The compact laser light source KE850 EasyPoint is your perfect helper for daily use in all fiber-optic networks.
W
KE8001 - KE8083 are optical measurement sets with or without VFL, stored in a hard plastic case for complete, quick and easy attenuation measurements during installation, maintenance and troubleshooting.
Multi Mode
E N
Fiber Optic Testing
Single Mode
KE80xx Fiber Optic Test Sets
Benefit n Fast and accurate attenuation measurement n Easy-to-use test equipement,rugged and handy n Suitable for single- and multimode applications n Optional with optical visual fault locator VFL n 2.4" LCD display with backlight * Fig. KE8082, test cable not included
n Variably measuring adapter system n Supplied in impact-resistant plastic case with batteries
Measuring case
KE8001
KE8081
KE8002
KE8082
KE8003
KE8083
Fiber type
Multimode
Multimode
Singlemode
Singlemode
Single-/Multimode
Single-/Multimode
Application
LAN/WAN
Ò
Ò
Ò
Ò
Ò
Ò
Enterprise
Ò
Ò
Ò
Ò
Ò
Ò
Access
Ò
Ò
Ò
Ò
FTTx
Ò
Ò
Ò
Ò
Ò
Ò
Ò
Ò
Metro
Ò
Ò
Ò
Ò
Ò
Ò
Carrier Ethernet
Ò
Ò
Ò
Ò
Ò
Ò
Ò
Ò
Ò
Ò
PON
Telecom Wavelength range in nm
850, 1300
850, 1300
1310, 1490, 1550
1310, 1490, 1550 850, 1300 1310, 1490, 1550
850, 1300 1310, 1490, 1550
Power Meter
KE8000
KE8000
KE8000
KE8000
KE8000
KE8000
Light Source
KE8100
KE8100
KE8200
KE8200
KE8100 & KE8200
KE8100 & KE8200
VFL Visual Fault Locator 650 nm
–
KE850
–
KE850
–
KE850
Dimensions
340 x 270 x 80 mm
Weight
700 g
800 g
700 g
800 g
1050 g
1150 g
No.
0.49125
0.49125-8
0.49135
0.49135-8
0.49150
0.49150-8
Accessories
20
Test cable SM
Test cable MM
Coppler
Plug-in adapter
2 m, Simplex
2 m, Simplex
fiber, Simplex
fiber, metallic
SC/PC - SC/PC No. 0.57130
SC/PC - SC/PC No. 0.57134
SC - SC (Plastik) No. 0.57145
2,5 mm – 1,25 mm No. 1400070
SC/PC - LC/PC No. 0.57131
SC/PC - LC/PC No. 0.57135
LC - LC (Plastik) No. 0.57146
2,5 mm – POF No. 1400080
SC/PC - ST/PC No. 0.57132
SC/PC - ST/PC No. 0.57136
ST - ST (Metall) No. 0.57128
SC/PC - FC/PC No. 0.57133
SC/PC - FC/PC No. 0.57137
FC - FC (Metall) No. 0.57127
Cable & Line Tracer
KE301 - KE2093 Cable & Line Tracer Kits Facilitate and accelerate with the Cable & Line Tracer Kits KE301 - KE2093 your everyday work in telephone / data networks and electrical installations. In the shortest time, you can quickly and easily find all kinds of cables, wires and wire pairs and detect errors such as cracks, breaks, exchanges or overdrafts.
Benefits n For power cables, telephone cables, bell lines, data cables from all classes and coax cable n Used in bundles, trays, under plaster, distributors, harnesses and much more. n Overvoltage protection up to 500 V AC / DC (Depending on model) n Audible and visual signal indicators and different search frequencies n Signal feed on active phone and data lines n Receiver with red ISDN signal detection (depending on model) n LED filter function for 1 kHz / 577 Hz for visual search signal detection n Receiver with torch function for dark search areas n Suitable for house, construction sites and in industrial environments
KE301 Classic
KE401 IT
KE501 Elektro
KE701 Telco
EASYTEST KE300 and Probe310
EASYTEST KE400 and Probe410
EASYTEST KE500 and Probe510
EASYTEST KE720 and Probe410
Fiber & Kupfer EASYTEST KE800 and Probe410
POTS
Telco
Electric
Telco
Telco/Fiber
Electric
Transmitter with Aligator-Clips and RJ11
n
n
Aligator
n
n
Aligator
RJ45 plug with Dataport finder
–
n
–
n
n
–
–
–
–
n
–
Comparison sheet Line Tracer n standard
– not available
Ideally suited for:
KE801
KE2093 Line Tracer
Connections
Build in fiberoptic visual fault locator
CAT II CAT III 300 V
Coax F-connector
–
–
–
–
n
–
Fully insulated test leads CAT II/III 300 V
–
–
n
–
–
n
500 V AC
500 V AC
500 V AC
300 V AC/DC
–
–
n
Special Features Over voltage protection
300 V
Cable tracing on powered lines up to 300 V
120 V AC/DC 120 V AC/DC –
–
–
n / n LED
n / n LED
n / n LED
Receiver Probe detects active ISDN signals
–
n
–
n
n
–
Receiver Probe with torch light function
n
n
n
n
n
–
Quality - Made in Germany
n
n
n
n
n
EU
0.49562
0.49563
0.49564
0.49567
0.49568
0.49570
Continuity test / resistance test
n / n + Ton(e) n / n + Ton(e)
–
Performance
in Made ny Germa
No.
21
OB E
1.2 Locating of all kind of cables PR
Cable length up to 10 miles
OB E
The pair with the strongest signal is the right one.
Known pair
Up to 24"
CONT DATA TONE
Audible CONT
CONT DATA TONE
Audible CONT
OFF
PR
OB E
PR
1. GENERAL
1.1 Pair identifying
OFF
SOLID
>100V CONT
ALT
REV OK
DATA
Up to 10 miles
POL
SOLID
>100V CONT
ALT
REV OK
DATA
POL
Ground
} No signal (low) SOLID/ALT
SOLID/ALT
2. TELECOM
Checking for voltage and polarity in Telephone systems, Intercom, Burglar Alarm. Trace the cable path also for cable inside a wall (Up to 12"). After plug in you will see voltage and polarity. In mode CONT check for Continuity; in mode SOLID/ALT trace of the cable path thruwalls, distribution boxes - to the Pabx or central office. Trace of the cable see 1.2
- PABX - Central Office - Alarm System
OB
CONT DATA TONE
E
Audible CONT
Fast and easy check and trace of bridges.
PR
Cable & Line Tracer
Applications
OFF SOLID
>100V CONT
ALT
REV OK
DATA
PR
O
POL
BE
Not KE5xx
Continuity, easy to find out if an network outlet is patched or not. If he is patched, the CONT- LED will light. If it is not patched, select SOLID/ALT and find with the PROBE easy and fast the right port. If the Port is active, KE4xx/7xx/8xx will transmit a LINK-Pulse. The corresponding LINK-LED on the HUB or Router will start blinking to indicate the right port. E
OB
PR
The easiest way to find the right patch cable or port!
3. DATA
Trace of the cable see 1.2
The attached LINK-LED will blink.
Patch Panel OB
PR E
CONT DATA TONE
Audible CONT
OFF SOLID
>100V CONT
ALT
REV OK
Office Dataport
DATA
POL
Works with the most popular units
Tone
In power cable installations is it possible to trace the cable path from the outlet up to the specified fuse.
No Tone Connect open wires together and connect to ground BE
Trace the cable path
O
PR
Open CONT DATA TONE
CONT DATA TONE
Audible CONT
E
Audible CONT
PROB
E
OB
PR
4. ELECTRO
Locates shorts and opens in power wiring. Trace of the cable path to the open.
Network Server
OFF
OFF SOLID
>100V CONT
ALT
REV OK
SOLID DATA
>100V CONT
POL
ALT
REV OK
CAUTION! Use only on de-energized power cables!
SOLID/ALT
DATA
POL
CAUTION! Use only on de-energized power cables!
SOLID/ALT
Fusebox
5. SPLIT
Often hand terminated cables are built with incorrect wire assignments. This means that wire pairs become intertwined. This fault is called “split pair”. Every high quality service on this pair will have problems. In analog systems for example a modem will have no speed, in ISDN, you will have undefined breakdowns, and so on. This occurs only because this pair have a lot of noise produced from crosstalk. With EASYTEST and PROBE easy to find and solve the problem.
1
1 CONT DATA TONE
Audible CONT
OFF SOLID
>100V CONT
ALT
REV OK
3
A B
DATA
Easy location of the connected pair.
PROBE
3
2
2
4
4
The corresponding pair is also easy located.
PROBE
POL
22
Fiber-optic connector
KE800 Audible CONT
Copper &
CONT DATA TONE
Fiber breaks and bad splices leak red laser light
OFF SOLID LASER ON/OFF
6. FIBER - FTTx
Sharp bends also leak red laser light
Coax F-connector
ALT
>100V CONT REV OK
DATA
POL
CAUTION! Laser Aperture class 2 - do not stare into beam!
The far end of the cable is easily spotted by the red laser light, even if there are faults
Cable & Line Tracer
EASYTEST KE300 / KE400 / KE500 / KE720 / KE800
PROBE310 / PROBE410 / PROBE510
Housing
Heavy duty water resistant housing made from ABS, elastomeric silicon rubber push button switches
Heavy duty water resistant housing made from ABS
Test leads
KE300: 25 cm durable wire leads with solid alligator clips and one with modular plug RJ11 KE400: 25cm durable wire leads with solid alligator clips and one with a special long modular plug RJ11 and RJ45 KE500: Durable wire leads, 35 cm long, with banana plugs and extra solid alligator clips KE720: 25cm durable wire leads with 4 mm bananaplugs and one with a special long modular plug RJ11 and RJ45 and latch protection KE800: 25 cm durable wire leads with 4 mm bananaplugs and one with a special long modular plug RJ11/RJ45 and latch protection with F-Connector for coax cables and 2.5 mm Fiber Jack.
Search frequencies
Six frequencies selectable
Features
n Test Continuity by LED and audible n Resistance Test by changing audible tone n Low Batt indication by flashing LED n Auto shut Off after 45 minutes n Auto shut OFF override indication by flashing LED n Gold plated contacts n Unit ON-Indication by LED n Indication of ALTernating Frequency by blinking LED n Indication of Solid frequencie by steady LED n Test leads protected by rubber-strain relief n Separate battery compartment
n Filtered Signal LED n Torch light function n Non-conductive solid carbon fiber tip n 3.5 mm Earphone Jack n Gold Plated Contacts n Separate battery compartment Only PROBE410 n Red LED for ISDN signal indication
KE500/KE720/ KE800
n Alarm Tone and LED by voltage > 100 V AC
KE400/KE720/ KE800
n Data Port test with HUB-Blink
Only KE800
Fiber: Laser Source: Wavelength 650 nm, Optical Output Power <1 mW Fiber coupled power: Into singlemode fiber 9/125 µm max 600 µW Into multimode fiber 50/125 µm max 600 µW Operating Mode: Continuous Wave (CW) and Pulse Mode with 270 Hz / 1 KHz Laser Protection Class 2 Suitable Ferrule 2,5 mm, DIN, E2000, FC, SC, ST Adapter 1.25 mm / POF available
Overvoltage protection
KE300 / KE400: Up to 120 V AC/DC in TONE Mode KE500 / KE720 / KE800: Up to 500 V AC/DC in TONE Mode
Distance
Trace cable length up to 15 km (no load)
Power Output
High Power Output (Battery 9,2 V) : 9,0 V PP no load 10 dBm into 600 Ohm 9 dBm into 100 Ohm 7,5 dBm into 50 Ohm Tone over shorted pair up to 250 m. (Inhouse) KE800: Tone over Coax only with open end possible
Power supply
9 V Alkaline Battery > 100 h lifetime in tone mode Only KE800: Fiber optical testing < 5 h
9 V Alkaline Battery > 100 h lifetime
Dimensions
68 x 96 x 25 mm
220 x 40 / 35 x 25 mm
Weight
150 g without battery
80 g without battery
Search distance to the cable up to 60 cm
Technical data and application examples for KE2093 can be found on our website: http://www.kurthelectronic.de
23
Cable & Line Tracer
Accessories Breakout adapter This modular adapter allows in-line testing for any plug/jack combination. It includes two 4-pair jacks plus a 152 mm (6 in.) modular cord terminated with 4-pair "universal" plug for accessing any standard 6- or 8-position jack. Individual conductors are broken out by pin number and correspond to eight separate test pads. Easytest can be securely attached to the test pads using alligator clips. For quick reference in the field, USOC, T568A, and T568B wiring charts are printed right onto the adapter body. The perfect addition to our cable finder kit. No.
Description
0.49700
Adapter Modular Break Out with RJ11/RJ45 plug and TAE-Adapter
Earset for Probe The earphone is used in conjunction with the PROBE preferably to increase the detection sensitivity (up to 1.5 m distance). Thus, it is perfectly possible to locate cables for example in suspended ceilings. But even as a hearing aid in very noisy areas or as protection for bystanders in quieter environments or offices the earphone is inserted. No.
Description
0.49600
Earphone for inductive Speaker Probe310/410/510
Testtip Testtip 4 mm of fiber reinforced conductive plastic for search signal receiver PROBE 310/410/510 up to year 2009, packing unit = 3 pcs. No.
Description
0.57772-VPE
Testtips 4 mm for Probe 310/410/510
Testtip (new model) Testtip of fiber reinforced conductive plastic with bayonet lock for search signal receiver PROBE 310/410/510 for easy changing without opening the device. From year 2009, packing unit = 3 pcs.
No.
Description
0.57773-VPE
Testtips with bayonet lock for Probe 310/410/510
Fiber Adapter for KE800 (also for Fiber Optic Tester KE8000 - KE8200 and KE850 VFL) n Adapts any 2.5 mm Fiber Jack to 1.25 mm (No. 1400070) n Adapts any 2.5 mm Fiber Jack to POF 1,5 mm and 2,2 mm (No. 1400080) n Especially for devices with visible laser light source n Be used with any Tester n Small, compact and easy attachable Specifications Side test device Side fiber Usefull for Attenuation Weight Dimensions
No. 1400070 2,50 mm SM-Ferrule 1,25 mm LC, MU, F3000, etc. FPC or APC < 1,0 dB 10 g 8,5 mm x 26 mm
No.
Description
1400070
Fiber Adapter for 2,5 mm jack to 1,25 mm
1400080
Fiber Adapter for 2,5 mm jack to POF
No. 1400080 2,50 mm SM-Ferrule 1,5 mm and 2,2 mm POF POF < 1,0 dB 10 g 8,5 mm x 26 mm
Pouch Cable & Line Tracer Kit with belt clip Suitable for the Cable & Line Tracer Kits KE301 up to KE801
24
No.
Description
0.49688
Pouch with belt clip
Buried Cable Path Locator
Stick PLS The Pathfinder Stick PLS is designed in a compact and robust way to withstand years of field abuse.An innovative concept, the receiver is a one-piece design that is lightweight and accurate. The receiver picks up signal easily at waist hight, thus eliminating the “Duck Walk“, and there are no cords dangling around the users legs since the receiver features a built-in probe. This superior technology and filtering allows the user to locate in or around power lines without interference.
Benefits n n n n n n n
Multiple frequencies options avaiable on both transmitter and receiver LCD bar graph on both transmitter and receiver Push button digital depth 3 watt transmitter for direct connection, transmitter and coupled induction Automatic impendance matching Locates pipes, cables, water-and gas service lines Signal feeding with direct coupling or inductive coupling with the build-in transmitter coil
No.
Type
Description
001-00380
Stick PLS
Digital Cable and Pipe Locator with depth measurement, test leads, pouch
8879 PLS The 8879 PLS Pathfinder with SDF-TechnologyTM is the top of the line model with new features such as a Backlight, Passive RF Frequency, Pinpoint Peak, Improved Induction Capabilities, and an Expanded Bar Graph, the 8879 PLS ensures an accurate locate while maintaining it ease of use. The 8879 PLS is ideal for locating all metallic utilities. From telephone to water, the 8879RF is accurate and dependable. Push-button depth, current measurement, and digital display make this light weight unit a highly versatile locator.
Benefits n n n n n n n n n
Four active frequencies and two passive frequencies Simple operation with push button depth Peak and null operation Current measurement Transmits up to 5 Watts Automatic impedance matching Manual gain control for locating accuracy Visual display with backlight Optional Accessories available
No.
Type
Description
001-00321
8879 PLS
Digital Cable and Pipe Locator with depth measurement, test leads, battery charger, pouch
Accessories
25
No.
Type
Description
001-00116
Sonde
Pipe and Sewer Sonde for Stick PLS and 8879 PLS for tracking of non-metallic pipes or bottlenecks
001-00245
Flex Koppler
Flexible Inductive Coupler for Stick PLS and 8879 PLS for inductive signal injection in active lines, object diameter not exceeding 150 mm
001-00119
Probe
Cable Identifier Probe for 8879 PLS to identify individual cables in the wiring harness or bundle
001-00087
GRP
Sheath fault locating receiver for 8879 PLS for locating ground fault or lightning strike on the cable
Buried Cable Path Locator
Stick PLS
8879 PLS
8 kHz, 33 kHz, 82 kHz, 118 kHz, 200 kHz
815 Hz, 33 kHz, 8 kHz, 82 kHz
Receiver Frequency Frequency passive
50 Hz, RF
Noise rejection
116 dB min
Gain
126 dB min
Automatic centering, manual gain adjustment Dynamic range 126 dB
Audio indication variable pitch control
Audio indication in variable pitch response
Indicator
LCD bar graph, low battery, signal strength and mode indicators
LCD bar graph, low battery, signal strength and mode indicators
Depth meas.
Push button digital depth and manual Triangulation method
up to 5 m depth, indication in meter and centimeter
Antenna Mode
Peak horizontal coil, Left & Right
Peak evaluation / neutral evaluation Peak / Null
Power supply
6 x AA 1,5 V Batteries
6 x 1,5 V LR14
Batt. lifetime
40 h continuous testing
> 82 h
Accuracy
815 Hz 82 kHz
< 1,5 m ± 1 - 6 % < 7,5 m ± 5 - 12 %
Operation temp. -20°C up to 55°C
-20°C up to 55°C
Dimensions
77 x 3,8 cm
77 x 24 cm
Weight
0,7 kg
1,3 kg
Frequency
8 kHz, 33 kHz, 82 kHz, 118 kHz, 200 kHz
815 Hz, 33 kHz, 8 kHz, 82 kHz
Indicator
AC load assistance measurement, low battery indicator with modulated battery warning
AC load assistence measurement, battery control and frequency control
Load matching
automatic from 5 Ohm to 25.000 Ohm
automatic from 5 Ohm to 20.000 Ohm
Output power
from 0,2 Watt to max. 3 Watt
from 0,2 Watt to max. 5 Watt
Power supply
8 x C Batteries
rechargeable Battery
Batt. lifetime
> 30 h depending on transmission power
Continuous 8 to 15 h, intermittent 40 to 60 h
Transmitter
26
Operation temp. -20°C to 55°C
-20°C to 55°C
Dimensions
21 x 15 x 6 cm
41 x 16 x 15 cm
Weight
2,8 kg
5 kg
Cable Conductor Test Set with Voice Connection 27
TalkSet The Talk Set provides you simple test jobs on analogue-fed lines, PBXs, etc. The more actual expectant problem today is the risky use of mobile phones or handheld radios in the installation and maintenance of equipment. In hospitals, IT departments, to open controls, etc. there is a risk of exposure in microprocessor controlled devices and equipment. The security risks are not estimable, therefore, the use of radios or mobile phones is now prohibited in these areas. With two talk sets, you can conduct a voice communication over telephone lines active without irradiate in microprocessor controlled devices or systems.
Benefits n Used for installations, service and maintenance at analoge lines n Non disturbing in-house-communication n High impedance Monitor n Up to 10 km distance depending on cable and power supply
Operating Voltage
3 - 60 V DC
Line Current
up to 20 mA
Protection
up to 400 V DC ITU K44, headset with shock protection
Monitor-Impedance
> 100 kOhm DC
Talk-Impedance
600 Ohm
Microphone
Electret, noise compensated
Test leads
0,85 m long, RJ11/ Bananaplug
Distance
up to 10 km depending on cable and power supply
Housing
heavy duty ABS plastic weather-resistant design
Dimensions
connector unit: 35,7 x 56,7 x 24,3 mm
Weight
60 g with headset
Delivery
2 x Headset with Microphone, 2 x Connector unit with test leads and alligator clips in pouch
No.
Type
Description
0.49610
TalkSet
Talk Set for two-way communication
Cable Conductor Test Set with Voice Connection
CCTS-03 The CCTS-03 quickly and easily checks the individual wires for continuity, exchange, contact and earth fault. The voice communication on free lines guaranteed time and cost savings. There is always a voice connection between the technicians. The microprocessor-controlled comparisons (120 ohms), a clear distinction between A-and B-Core also be realized with loaded lines with low impedance.
Benefits n Indispensable for fault tracking, maintainance, setup n Useful also on powered telecom lines n Line resistance up to 2000 Ohm n Microprocessor for tuning on life lines n xDSL and Data safe n Over voltage protected n To perform a test you need at least two CCTS-03
CCTS-03 Housing
heavy duty ABS plastic weather-resistant design
Dimensions
160 x 95 x 35 mm
Weight
350 g with Battery, test leads and headset
Power source
9 V Alkali Battery
Battery lifetime
up to 10 hours continous use
Test leads
150 cm flexible PVC with 4 mm Bananaplug
Connection
fully insulated clips
Headset Standard headset Weight
approx. 60 g
Equipement
Receiver single-sided left or right, microphone noise compensated
Headset for hard hat use Weight
approx. 40 g
Equipement
Receiver single-sided left, Receiver single-sided left
Connection
28
Talk path
free double conductor, no polarity
Test path
free or wired twisted pair
Over voltage protection
automatic resetting fuse
Life lines tuning
auto tuning, microprocessor controlled
Test distance
up to 2000 Ohm
Talk distance
> 3000 Ohm
Wire pair resistance
in terms of cable length without coil-loading:
wire diameter 0,4 mm wire diameter 0,6 mm wire diameter 0,8 mm
approx. 285 Ohm/km approx. 117 Ohm/km approx. 66 Ohm/km
No.
Type
Description
0.49617
CCTS-03
CCTS-03, operation manual, test leads 1,5 m, 2 x black and 1 x red, 2 x test clips KLEPS30 black, 1 x needle tip PRÜF2 red, 1 x headset, 1 x headset for hard hat use, 1 x Cordura pouch
Analog Test Telephone / ISDN BRI Tester
TP09D The TP09D is the perfect tool for the day today needs of telecom and data technicians. The handy and rugged, waterproof analog test set offers many features despite simple operation. With the large graphical display and clearly keypad all values fare in fast view - such as the MWI-/CID-/DTMF-evaluation.
Benefits n n n n n n n n
Voltage, current and polarity display Direct flash button / pulse and tone dialing Monitor for active and passive line 10 memory speed dialing Shows calling number (CID) and Message Waiting (MWI) DTMF processing in monitor mode High and low voltage detect with lockout High impedance Monitor > 500 Kohm/ 100 KHz
Line Impedance
complex or real
Pulse Dialing
Rate: 10 pps +/-5%
Ratio: 40/60, 33/66
Tone Dialing
Freq. Error: +/- 1%
Level:High group -6 dBm
Flash Duration
100 ms, 270 ms, 600 ms
Pause Duration
2 sec per key in
Memory
2 programmable, 1 LNR, 1 CID RCL with 24 digits each, 10 indirect locations with 24 digits each
Monitor impedanz
> 120 kOhm at 100 kHz
Power supply
9 V Alkaline
Display
Graphical LCD
Housing
Heavy duty water resistant housing made from ABS, Mylar push button switches / water-resistant seal IP54
Test leads
60” (150 cm) durable wire leads with solid alligator clips, field replaceable, optional 6A clips, others by request. Strain relief and separate battery compartment with captive screw
Dimensions
250 x 80 x 30/70 mm
Weight
450 g with battery
Low group -8 dBm
> 500 kOhm at 4 kHz
No.
Type
Description
0.49310
TP09D
Analog Test Telephone with display, long test leads and pouch
ISDN P-MP-Tester Checking the ISDN-S/T-Interface with the ICHECKplus is very easy to do even for a non-expert in the field of telecommunications in a quick and user-friendly way. The ICHECKplus is used to check the basic NT functions and the ISDN installation for wiring- and application faults.
Benefits n Indication of ISDN-activity via LEDs n Fast indication of cabling faults n Two jacks for in-line connection
29
Indication
4 twin-colour LED (red/green), Layer 1 indication, 2 LED NT/TE for activity indication
Connections
2 x RJ45 (with flexible test lead, length 190 mm)
Dimensions / Weight
35,7 x 56,7 x 24,3 mm / 24 g
Power Source
from S/T-Interface (current max. 8mA all LEDs ON)
No.
Type
Description
0.49801
ICHECKplus
ISDN Installation Tester and Activity Monitor
U
The KE-TDR06 can locate the presence of cable faults, including shorts, opens, taps, splices, water ingress and other impedance anomalies, on copper communication cables up to a distance of 6000 m.
N E
Cable Fault Meters
KE-TDR06
Benefits n For telecom, video, data and security systems n Easy-to-use and robust housing n Clear presentation on the LCD graphic display No.
Type
Description
04403400
KE-TDR06
TDR lenght measurement from 0,5 - 6.000 m, test leads, pouch
KE-TDR20 The KE-TDR20 is purpose designed for balanced telecommunications cable. Seven test modes give fast fault location testing a single pair or comparing two pairs, one pair compared to any of the 100 memories, or crosstalk between two pairs. Fast function configuration. Dedicated keys for the most frequently used functions. All faults clearly identified from open circuits to wet joints.
Benefits n Precise localization of cable faults n Cable length up to 32,000 m n 2-channel input for comparative measurements n Large, clear color display of full trace for accurate diagnosis n 100 memories for on-site-waveform and storage and camparison n Internal rechargable battery pack No.
Type
Description
0.490326
KE-TDR20
TDR lenght measurement up to 32 km, test leads, software, pouch
KE-FLB Fault Locator Bridge The Fault Locator Bridge KE-FLB is a microprocessor controlled, DC and AC cable measuring instrument intended for fast and accurate fault location and quality testing of telecommunication cables.
Benefits n Cable measuring for fault localization and quality testing of copper pairs n DC and AC fault location measurement n Mutual, conductor-shield capacitive measurements, n Fast and easy error detection n 7 several Testmodes and up to 32 measurement results can be stored n Rechargeable batteries included (approx.8 h operation time) No.
Type
Description
KE-FLB
KE-FLB
Fault Locator bridge AC/DC up to 20 GigaOhm, test leads, power supply, software and pouch
KE-LQ20 Cable Parameter Tester The xDSL Line Qualifier KE-LQ20 is a hand held battery operated, multifunction measuring instrument, intended for pre-qualification, installation, fault location and maintenance of balanced copper pairs. For fault location DC-AC bridge, TDR and basic cable parameter measuring all in one unit.
Benefits n Ideal for prequalification, installation and maintenance of symmetrical copper pairs n Measuring all major cable parameters for prequalification for: ADSL, HDSL, SHDSL, ISDN, PCM n TDR measurement error up to 10 km cable length n Large LCD display and built-in rechargeable battery with up to 8 hours of run time n Various software and hardware options
30
No.
Type
Description
KE-LQ20
KE-LQ20
Line Qualifier for ADSL, HDSL, SHDSL and ISDN with TDR up to 10 km, test leads, power supply, software and pouch
Product Range n xDSL Tester n Cable & Line Tracer n LAN & Ethernet Tester n Network Testing Sets n Gigabit Dual-Port Tester
n Analog Test Telephone n ISDN Tester n Cable Conductor Test Set n Buried Cable Path Locator n Cable Fault Meters
®
In North America
Global
Kurth Electronic, Inc. Attn: Jim Carefoot P.O. Box 1377 Sparta, NJ 07871 Telephone: 877 234-7081 Fax: 877 234-7080
[email protected] or
[email protected] www.kurthelectronic.com
Kurth Electronic GmbH Muehleweg 11 72800 Eningen u.A. Germany Telephone: +49 (0) 7121-9755-0 Fax: +49 (0) 7121-9755-56
[email protected] www.kurthelectronic.de
01/15 Product design and specifications subject to change without notice. All trademarks belong to their respective companies.
n Fiber Optic Testing
