Transcript
Product Bulletin
Model H301 10 Gb/s Optical Modulator Driver
The H301 optical modulator driver provides a high-quality, single-ended voltage to drive an external laser modulator. Typical applications include driving EML, EAM, and Mach-Zehnder style modulators. It amplifies 2.488 to 12.2 Gb/s data input signals to >+7.0 Vpp drive levels. The flat gain and flat group delay response yield a highquality, low-jitter electrical drive signal. The driver meets applicable SONET and SDH standards for OC-192 10 Gb/s optical transmitters and includes reference and detector outputs to enable external temperature-compensated control of output drive levels. The module has field replaceable input and output K-connectors for the input/output drive signals and an eight-pin connector for the detector, reference, and power interfaces.
Key Features Low power, 4.9 W Low jitter Data rates from 2.488 to 12.2 Gb/s Applications SONET/SDH equipment SR, IR, LR optical transmitters
ReferenceOUT DetectorOUT
GainControl
Model H301 | 2
Optical Specifications Parameter
Specification
Min
Data rate Frequency response Output amplitude P1dB output Psat output Gain Gain ripple Gain control range (0 to -10 Vdc using external 510 W resistor) Group delay (2 to 10 GHz) Noise figure Input, output impedance Input range Input VSWR
2.488 to 12.2 Gb/s 75 KHz to 10 GHz >+7V >22 dBm >24 dBm 14 to 24 dB, variable ±1.5 dB
2.488 Gb/s 75 KHz
Output VSWR Isolated run of ones or zeros Pulse response (typical)
Gain and Return Loss vs. Frequency
24 dB
10 dB 11 dB 50 ohms 500 mv to 1.5V 75 to 200 KHz 200 KHz to -10 GHz 100 bits Overshoot/undershoot 10% Droop 10% Risetime 40 ps
Typ
7.0vpp 22 dBm 24 dBm 26 dB
Max 12.2 Gb/s 10 GHz 7.5 vpp 23 dBm
12 dB ±25 ps
1.9 1.6:1 2.0:1
2.25:1 2.25:1 3.0:1
Model H301 | 3
General Specifications Minimum Operating temperature Storage temperature
Nominal
Maximum
0 °C -40 °C
70 °C 100 °C
0
85 % 97 % 3,048 m (10,000 ft) 215 °C 150 °C
Operating humidity, non-condensing Storage humidity, non-condensing Altitude Soldering process temperature (30 seconds) Process temperature (24 hours) Dimensions (W x H x D)
3.0 x 1.4 x 2.4 cm (1.2 x 0.5 x 1.0 in)
Power requirements
+8.0 V DC at 600 mA
+0.5 V +0.5 V
Total power dissipation Input/output Power detector/reference/ground
–5.0 V DC at 22 mA 4.9 W 2.9 mm (field replacement “K”) 8-pin package
Applications
SONET/SDH SR, IR, LR optical transmitters
Eye Diagram
Model H301 | 4
DET
VGAN
RF OUTPUT
REF
+8V
GND
-5V
Pin/Connector K - F or M 1 2 3 4 K - F or M 5 6 7 8
GND
+8V RF INPUT
Optical Modulator Driver H301 S/N:MYYWW-WXYZ-XXX MADE IN USA
Name (as viewed from top, traversing clockwise) INPUT (AC coupled) VC (8 V) Ground Bias (VGain) Det (VDet) OUTPUT (AC coupled) Ref VC (8 V) Ground VEE (-5.0 V DC) Case is grounded internally
Ordering Information For more information on this or other products and their availability, please contact your local JDS Uniphase sales representative or JDS Uniphase directly at 321 984-3671, or by fax 321 728-0487, or via e-mail at
[email protected], or visit our web site at www.jdsuniphase.com.
H301-WXYZ W 1 2 3 4
Connector Female in, Female out Female in, Male out Male in, Male out Male in, Female out
JDS Uniphase Corporation 305 East Drive
Melbourne Florida 32904 USA
X 1 2 3
Driver Option Standard Optimized for JDSU modulator Am modulation input pin
Tel 321 984-3671 Fax 321 728-0487
[email protected] www.jdsuniphase.com
Y 1
Temperature Range 0 °C to 70 °C
Z 0
Reserved Reserved
All information contained herein is believed to be accurate and is subject to change without notice. No responsibility is assumed for its use. JDS Uniphase Corporation, its subsidiaries and affiliates, or manufacturer, reserve the right to make changes, without notice, to product design, product components, and product manufacturing methods. Some specific combinations of options may not be available. Please contact JDS Uniphase for more information. ©JDS Uniphase Corporation. All rights reserved. MKT-DS-0197 Rev.B 02/01 Printed in USA
