Transcript
774-477 Preservative for Exterior Wood Green Product Description
Characteristics
The green preservative for exterior wood protects wood against mildew and rot, swelling and warping. Ideal for lumber.
Physical Form
Advantages
Quality
• • • • • • •
Easy to use: requires no dilution. Very penetrating and very thin liquid, permanent. Very effective against wood rot and mildew. Extends wood life. May be coated with paint, stain or a protective product. Non-corrosive to metals, and does not cause damage to plants when dry. Does not form a film on the surface, but gives a tint to the wood without concealing the grain.
Projects Environment
Exterior. Use
Exclusively above-ground surfaces: structural timber, beams, doors, frames, stairs, posts, greenhouse and garden lumber that comes in contact with inedible plant substances only. Surfaces
New work or bare materials exclusively located above ground. All types of solid wood: plywood, pressure-treated wood. Notes
• Exterior use only. • Do not apply by spraying or by immersion. • Do not use where copper naphthenate could contaminate livestock feeds or drinking water. • Do not apply on wood or any other surfaces on which edible food, drinking water or skin could be subjected for an extended period of time. • Do not use on textiles. • Never burn preservative treated wood or factory treated wood. Pre-mixed colors tinting bases and sizes Consult your retailer.
Liquid green Best Transparency
Not applicable Gloss Level
Not applicable Gloss Percentage
Gloss at 60°: Gloss at 85°: Composition
• Solution of white spirits and copper naphthenate • Copper content as copper naphthenate: minimum 2 % Spreading Rate (3.78 L)
280 to 360 ft² (24 to 32 m²) (depending on surface texture and porosity). Drying Time
48 hours before painting, staining or recoating. Viscosity
Not applicable Density
Not applicable Solids in volume
Not applicable Flash Point
Closed cup: 42°C (107.6°F) (ASTM D56) Inflammability
Flammable Certification
Pest Control Products Act: Registration No. 15013
TDS_774477 (2010-02-25) Akzo Nobel guarantees the quality of its products. They are in conformity with the description provided in the technical data sheets and on the labels for which they are intended, as indicated by the company. However, since the manufacturer has no control over the circumstances, the methods and the conditions appropriate to their intended uses, this guarantee applies only to the high quality of Polyprep products.
Surface Preparation
Recommendations
Surfaces to be treated must be clean, solid, and free from dust, dirt, oil, soot, wax, mildew and patina. • Clean surface with the appropriate product. Polyprep cleaner, brightener and conditioner is the most common cleaner used on bare wood. • Let surface dry for a minimum of 48 hours before applying preservative. The wood must have between 12 to 18% moisture content. • Sand horizontal surfaces with sandpaper grits No. 80 and vertical surfaces with No. 120. Vacuum sanding residues. (Sanding allows for better penetration of the preservative. Precautionary measures: treatments such as dry sanding or paint film burning may generate dust and harmful fumes. If possible, the wet sanding method should be used. If exposure cannot be avoided by means of local ventilation, wear a breathing mask).
Application Conditions
Application
Apply a protective coating on dry surfaces.
• This product is ready to use, and should not be diluted. • Always wear safety goggles, a protective mask, gloves and proper protective clothing when applying the product. • Only apply the product with a paintbrush, and not by spraying or immersion. • Saturate the ends of boards and joints. • Extend drying time if temperatures are cool or if humidity is high. Allow solvent to dry completely before reinserting plants to prevent phytotoxicity. • Thoroughly wash hands with soap after product application. • To obtain more information on application methods, visit the website at www.sico.ca Note
Be vigilant about the use of certain paint products as they may cause bleeding. Does not substitute the primer coat used on wood. FIRST AID If ingested, call poison control centre or physician immediately to obtain advice on treatment. Do not induce vomiting unless instructed to do so by poison control centre or physician. Do not have the person swallow any liquid. Do not have the unconscious person ingest anything. In case of contact with skin or clothing, remove all contaminated clothing. Immediately flush skin with running water during 15 to 20 minutes. Call a poison control centre or physician to obtain advice on treatment. In case of inhalation, move the person to fresh air. If the person does not breathe, call 911 or an ambulance, and then apply artificial respiration, preferably mouth-to-mouth resuscitation, if possible. Call poison control centre or physician to obtain advice on treatment. In case of contact with eyes, keep eyelids open, gently and slowly flush with water during 15 to 20 minutes. Where relevant, remove contact lenses after 5 minutes and keep on flushing with water. Call poison control centre or physician to obtain advice on treatment. Carry the container or the label with you or take note of the product name and registration number when looking for medical assistance.
• Temperature: 10°C to 29°C (50°F to 85°F) • Relative humidity: 45-55% • Apply in the shade and not during high winds. Tools
Paintbrush only Cleaning Tools
Use mineral spirit to clean tools. Surface Maintenance
Storage and Transportation
When not in use, keep container tightly closed in a cool and dry place, away from heat. Disposal of Residues
Contact your municipality to dispose of leftover products. Caution
Consult the safety data sheet. Keep out of reach of children. Harmful or fatal if ingested. Do not use near open flame or spark or in areas subject to excessive heat. Do not breathe vapours. Toxic if ingested or inhaled. Wear safety goggles, a protective mask, rubber or plastic gloves and appropriate protective clothing while applying product. After use, thoroughly clean yourself with water and soap before eating or smoking. This product may cause skin irritation. Avoid any contact with skin. Do not contaminate water outlets. This product is toxic for fish and animals.
TOXICOLOGICAL DATA Contains petroleum distillate and copper naphthenate. Treat as ingestion of kerosene.
TDS_774477 (2010-02-25) www.sico.ca/ 1 800 463-7426 Akzo Nobel, 2505 de la Métropole, Longueuil (Québec), Canada J4G 1E5
