Transcript
Construction Materials Testing Equipment
Volume 31
November, 2012
MinMax Thermometer This min-max thermometer indicates present temperature and the highest/ lowest temperatures since last setting of markers. -40 to 120ºF (2° div.) and -40 to 50ºC (1° div.), push-button reset. CA-0790 Min-Max Thermometer
Pressure Meter
Type B • ASTM C231, AASHTO T152 3 Heat treated aluminum lid and base for increased durability 3 Meters smooth sloped lid allows concrete and water to roll right off greatly reducing maintenance problems 3 Bowl is ¼ cu. ft. (.007m³) capacity, its base is machined flat so it sits level and firm when conducting a test, can also be used as a unit weight measure
3 Cast in handles make it easier to carry 3 Case has room for extra items The meter also features easy to use one-piece selflocking stainless steel clamps, a 4” diameter direct percentage reading gauge, all brass air pump with shield to keep dirt and water out of piston area, and a high-impact horizontal plastic carrying case. Kit includes: Meter, carrying case, syringe, tamping rod, strike-off bar, calibration vessel, inside and outside calibration tubes, instructions and parts list. $ CA-0500 Pressure Meter Kit . . . . . . . . .
616.00
Dial Type
Min-Max Thermometer Registers high and low readings. Manual reset. Range -20 to 140°F (-30 to 60°C) Dimensions: 3.5” x 5”. $ CA-0789 Dial Type Min-Max Thermometer. . . . . . . . . . . . . . . . . . . .
24.50
13.75 12.95
1 - 5 units. . . . . . . . . . . . . . . . . . . . $ 6 or more. . . . . . . . . . . . . . . . . . . $
Floating Thermometer Easy to read, -20 to 120°F, -30 to 50°C scale. Tether a string for easy removal. CA-0792 Floating Thermometer . . . . . . $
16.95
Curing Tank Heater 3 Adjustable Thermostat Heater is supplied with a mounting bracket and 3-prong grounded plug with fuse. Heater efficiency is increased when used with CA-0935 Water Circulating Pump.
157.50 CA-0935 Circulating Pump. . . . . . . . . . . . $ 82.50
CA-0933 Curing Tank Heater . . . . . . . . . $
Visit us in Booth N-1056 at World of Concrete, Las Vegas, February 5-8, 2013
View and Order Our Products Online 24/7 at www.testmark.net We Accept Visa, Mastercard and American Express
pH Meter pH Meter has a single line display with push button calibration, hold function and auto shut-off. Automatic temperature compensation provides accurate readings even in fluctuating temperatures. Unit includes meter, integral sensor and batteries. Range: -1.0 to 15.0 pH Resolution: 0.1 pH Accuracy: ± 0.1 pH Calibration: Three-point, automatic (4.0, 7.0 or 10.0) $ CA-0877 pH Tester. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
60.00
Buffer Solution Model No. Description CA-0873 Buffer Solution, pH 4.01, 1 pint (473 ml). . . . . . . . . . . . . . . . . . $ 13.00 CA-0874 Buffer Solution, pH 7.00, 1 pint (473 ml). . . . . . . . . . . . . . . . . . $ 13.00 CA-0875 Buffer Solution, pH 10.0, 1 pint (473 ml). . . . . . . . . . . . . . . . . .$ 13.00
Preparation Knife
Proctor Mold, 4” ASTM D558, D698, D1557 AASHTO T99, T134, T180
Mold has a volume of 1/30 cu. ft and is plated for rust resistance. Includes detachable base plate, studs and wing nuts. Dimensions of 4” ID x 4.584” H with 2” detachable collar.
94.50 134.00
SA-0100 4” Standard Proctor Mold . . . . . . . . . $ SA-0100-S 4” Split Proctor Mold. . . . . . . . .
$
Proctor Mold, 6” ASTM D698, D1557 AASHTO T99, T180
Mold has a volume of 1/13.33 cu. ft and is plated for rust resistance. Base plate is 8” x 8” x ½” thick. Dimensions of 6” ID x 4.584” H with 2” detachable collar.
Used for sample preparation and general lab work. Knife has 6” long thin, sharp blade with wood handle. SA-1000 Preparation knife . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
SA-0109 6” Modified Proctor Mold . . . . . . . . . . . . . . . . . . . . . . . . $ SA-0109-S 6” Split Proctor Mold. . . . . . . . . . . . . . . . . . . . . . . . . . . $
135.00 160.00
Shelby Tubes ASTM D1587 3” dia. thin walled sampling tubes are galvanized steel. A chamfered end forms a cutting edge, includes holes for securing tubes to a drive head. Plastic caps hold sample in tube during transportation and storage. $ SA-1380 3” dia. x 10” long Shelby Tube. . . . . . . . . . . . . . . . . $ SA-1382 3” dia. x 12” long Shelby Tube. . . . . . . . . . . . . . . . . $ SA-1384 3” dia. x 18” long Shelby Tube. . . . . . . . . . . . . . . $ SA-1389 Plastic Caps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.30 8.90 11.30 .29
Fiberglass Probe Rod
For protection against possible electrical shock when working around buried electrical lines. T-handle has high density nylon cover. Shaft is ½” dia. x 48” long, steel tip measures 5/8” x ¾”. $ SA-1302 Fiberglass probe rod . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
34.50
Straightedges
Compaction Hammers
ASTM C-185, D-558, D-559, D-560 & D-698, AASHTO T-137
ASTM D558, D598 AASHTO T99, T180
Hammer is plated for rust resistance; guide sleeve has four vent holes to release pressure, hard rubber ball handle. $ SA-0120 5.5 lb. Compaction Hammer, 12” drop. . . . . . . . . . . . . . . $ SA-0130 10 lb. Compaction Hammer, 18” drop. . . . . . . . . . . . . . .
74.00 90.60
Straightedges are for striking-off samples in molds or containers, made of ground steel with beveled edges. $ SA-0114 Straightedge, 1/8” x 1 1/4” x 8” long. . . . . . . . . . . . . . . . . . . $ SA-0115 Straightedge, 1/8” x 1 1/4” x 12” long. . . . . . . . . . . . . . . . . $ SA-0116 Straightedge, 1/8” x 1 1/4” x 16” long. . . . . . . . . . . . . . . . . .
16.10 19.00 31.75
New i720 Digital Indicator 3 Made in USA
The i720 is an easy to use digital that simultaneously displays both load and rate of load during a test, and automatically displays peak load and average rate of load at the end of a test, eliminating the need to toggle keys between test functions. All test data is clearly displayed on the indicator’s 5.3” wide, 240 pixel backlit V.G.A. display screen, with adjustable contrast settings. Up to 700 tests can be stored in memory and transferred directly into a spreadsheet file or a word document with USB Able Cable option, or printed on an optional serial printer. Stored data includes: test date and time, sample ID number, peak load and average rate of load.
Built for the harshest lab environment, all of its internal electrical components are protected in a NEMA-4 rated water/dust proof stainless steel enclosure, making it an ideal choice for mobile field laboratories where excessively high humidity levels are present. Its approvals and listings are NEMA-4, UL, CUL, CE and Measurement Canada. Its high speed sampling rates and digital filtering result in smooth and uniform control of load pacing rates. Accuracy exceeds ASTM C39 and E4 requirements through its password protected calibration program with 7 linearization points.
CM-2500-i720, 250,000 lbs. C.T.M. Rugged Time Proven Design
3 Featuring an American Made quiet running pump and control valve rated for continuous duty 3 Testing range of 2,500 to 250,000 lbs. with an accuracy of + .5% of indicated load 3 Ideal for both laboratory and mobile field testing The CM-2500 frame features our time tested wrap around box construction with each corner fully welded on both the inside and outside crosshead seams, for the rugged stability needed for accurate and repeatable test results year after year. Featuring steel fragment guard doors, hydraulic safety valve and remote mounted digital and transducer for added protection and longer service life. Machine is supplied with 6” cylinder platen. Warranty 2 years. Meets ASTM C39, E4 and AASHTO T22 specifications.
Request a Catalog http://www.testmark.net
Available options: stand, test platens and spacers for testing a variety of specimen types. See it on our website at www.testmark.net.
Neoprene Compression Pads ASTM C1231 AASHTO T22, T851
3 Pads are molded for a consistent thickness and diameter 3 Available in 50, 60 and 70 durometer hardness in four different sizes These neoprene pad inserts are made from a tough Elastomeric material that evens out and fills irregularities in the ends of concrete cylinders to assure even distribution of test loads for consistent results. CA-0191-50 6” Pad Cap, 50 duro 1 – 23 pcs.. . . . . $7.60 CA-0191-60 6” Pad Cap, 60 duro 1 – 23 pcs. . . . . . $7.25 CA-0191-70 6” Pad Cap, 70 duro 1 – 23 pcs. . . . . . $7.60 CA-0200-50 4” Pad Cap, 50 duro 1 – 23 pcs. . . . . . $7.00 CA-0200-60 4” Pad Cap, 60 duro 1 – 23 pcs. . . . . . $7.00 CA-0200-70 4” Pad Cap, 70 duro 1 – 23 pcs. . . . . . $7.00
24+. . . . . . . . $7.45 24+. . . . . . . . . $7.10 24+. . . . . . . . . $7.45 24+. . . . . . . . $6.85 24+. . . . . . . . $6.85 24+. . . . . . . . $6.85
Pad Cap Retainer Rings ASTM C1231 AASHTO T22
3 Made from plated high-alloy steel to resist rust and deformation fatigue 3 Bearing surfaces machined-plane to within 0.002” These pad-cap retainer rings hold neoprene pads that fit into the ends of concrete test cylinders. Supplied two per set.
140.00 $ CA-0200 4” Steel Retainer Rings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19.00 CA-0191 6” Steel Retainer Rings . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
$
View and Order Our Products Online 24/7 at www.testmark.net Slump Testing
Single-Use Plastic Molds
ASTM C-143
ASTM C 31, C 39, C 192, C 470, AASHTO T 22, T 23, T 126, T 198, M 205 3 Molds are injected plastic for close tolerances and consistency of shape 3 Molded, ribbed configuration gives added strength 3 Smooth surface allows quick and easy stripping 3 Seamless design prevents 3 Consistent size moisture loss Disposable plastic cylinder molds are used to mold concrete test cylinders. Plastic lids are sold separately. $ CA-0210 6” x 12” Cylinder Mold (20 per carton). . . . . . . . . . . . . . . . $ CA-0220 4” x 8” Cylinder Mold (36 per carton) . . . . . . . . . . . . . . . . $ CA-0210-01 6” Domed Lid, each. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ CA-0220-01 4” Domed Lid, each. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
28.75 29.95 .46 .39
4” Test Cylinder Carrying Case 3 Durable molded plastic rack holds (8) 4” x 8” concrete test cylinders for easier field to lab transport with less specimen damage Rack features large reinforced molded handles for easier carrying. Durable molded plastic will not deteriorate or corrode in water. Rack is 19” W x 9 5/8” D x 5 3/8” H. $ CA-0214 4” Test Cylinder Carrying Case. . . . . . . . . . . . . . . . . . . . . . .
18.45
151.00
CA-0360 Steel Slump Cone $
37.75
RELATED ITEM CA-0390 Steel Slump Cone Funnel $21.00
Pocket Dial Thermometers External nut for recalibration, corrosion-resistant stem. Supplied with plastic carrying case Model No.
Dial Dial
Range
Division
Length
CA-0760
1”
25–125°F
1°
5”
CA-0760
12+
CA-0770
1-5/8”
0–220ºF
2°
5”
CA-0780
1-5/8”
50–550ºF
5°
8”
8.95 5.95 $ 10.85 $ 14.50 $
$
Capping Compound ASTM C-617
Grout Sample Boxes ASTM C-617 3 Slotted, corrugated material simulates CMU absorption characteristics. 3 Performs as mold and transport container in one Grout Sample Boxes follow ASTM C1019 and UBC21-18 guidelines. Samples yield proven compressive strength values comparable to traditional molding methods using concrete masonry units. Each box creates four - 3” x 3” x 6 ½” test samples. Shipped 25 per carton. CA-0289 Grout Sample Box. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Set includes steel slump cone, aluminum test base, scoop and tamping rod. CA-0361-S Slump Test Set w/scoop $
$
133.00
3 Melts 25% faster than other flake type compounds 3 Compression strength of 8,000 psi by the 2” cube test method in 2 hours Compound comes in the form of ultra-thin flakes for better heat transfer, for faster melting and less dust when handling. It has been degassed during its pre-melting manufacturing process to reduce fumes and sulfur odor. This process also reduces material shrinkage during melting for more caps per bag. Supplied in 50 lb. reinforced bag. CA-0100 Capping Compound, 50 lb. bag
38.75 10 – 39 bags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37.75 $ 40+ bags. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34.50 1 – 9 bags . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
$
$
Digital Field Scale Kits
Wet Wash Sieves
ASTM C29, C138
3 Seamless brass construction
AASHTO T19, T121
These wet washing sieves have an extra deep frame to contain water, so fines are washed through the No. 200 mesh sieve without losing any portion of the sample. Sieves have brass frames and permanently installed stainless steel cloth.
Scales feature; four selectable weighing units, remote indicator with large 1” LCD display, and water resistant keypad. Scale can be operated with AC Adapter (included) or 6 - AA batteries (not included). Kit includes; scale, hard plastic carrying case, and wall mounting kit for display head. SC-0135 33 lbs. x 0.01 lbs. (15 kg x 5 g) . . . . . . . . . . . . . . . . . . . . . . . . . . . $280.00 SC-0136 75 lbs. x 0.02 lbs. (35 kg x 10 g). . . . . . . . . . . . . . . . . . . . . . . . . . $280.00 SC-0137 165 lbs. x 0.05 lbs. (75 kg x 20 g). . . . . . . . . . . . . . . . . . . . . . . . . $280.00 SC-0138 330 lbs. x 0.1 lbs. (150 kg x 50 g). . . . . . . . . . . . . . . . . . . . . . . . . $290.00 SC-0134 440 lbs. x 0.1 lbs. (200 kg x 50 g). . . . . . . . . . . . . . . . . . . . . . . . . $295.00 All models available without the carrying case.
Long Stem Digital, NIST Traceable Long-stem thermometer features 8” long x 1/8” dia. stainless steel probe. Overall length is 11”. Brilliant ¼” high LCD display updates reading every second. Temperature range is -58 to 302°F (-50 to 150°C) with resolution 0.1°F from -20 to 200°F, 1° resolution outside this range. Supplied with 1 year battery and certificate traceable to NIST standards. $ CA-0785-T Long Stem Digital Thermometer, NIST. . . . . . . . . . . .
48.00
149.95 CA-2002 No. 200 Wet Wash Sieve, 8” x 4” w/#16 back-up. . . . 169.50 $ CA-2005 No. 200 Wet Wash Sieve, 8” x 8” . . . . . . . . . . . . . . . . . . 154.00 $ CA-2007 No. 200 Wet Wash Sieve, 8” x 8” w/#16 back-up. . . 186.00 CA-2000-S No. 200 Wet Wash Sieve, 8” x 4”. . . . . . . . . . . . . . . . .
$
$
Compact Portable Balance 3 User selectable weighing units of kg, g, lb, oz, ct, d, GN, N, TL.T Scale features external calibration, AC adapter, battery power (6 - AA batteries, not included) and auto-power off function.
199.00 SC-0183 2600 g x 0.1 g. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 235.00 $ SC-0189 Carrying Case. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75.00 SC-0182 1500 g x 0.1 g. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
$
$
Crack Monitors A simple, accurate device for monitoring crack movement. Monitor features stamped crosshairs and grid with two acrylic plates which move independently. Each crack monitor comes with a graph for periodic recording of movement. Monitors may be installed using Quick-set Epoxy. Max Crack Movement Width Upward
Trident Moisture Meter
16.85 21.00 27.00
$ 3/4” (20 mm) 3/8” (10 mm) $ CA-1204 Corner Crack Monitor 3/4” (20 mm) 3/8” (10 mm) $ CA-1206 Standing Crack Monitor 25 mm 25 mm CA-1202 Flat Crack Monitor
ACCESSORY Epoxy sets in 3 – 5 minutes at 75°F. Bonds to concrete, stone, wood, glass and metal. Contains no solvent and will not shrink. CA-1210 Quick-Set Epoxy. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . $ 2.95
The Trident Moisture Meter measures moisture content in various fine and coarsegrained materials. The prongs of the probe are inserted into the material to be tested and the percentage of moisture content is instantaneously shown on the display. The Trident comes calibrated for both sand and aggregate, and can be programmed by the user for up to ten different materials. The Trident can store more than 150 readings, complete with time and date for future reference. Complete system includes meter, sensor probe, sensor cable and software. Meter operates on 4 – AA batteries. $ CA-2575 Trident Moisture Meter. . . . . . . . . . . . . . . . . . . . . . . .
2,259.00
Volume 31 • November, 2012 • Prices are subject to change 995 North Market St. East Palestine, OH 44413
Lightweight Aluminum Roll-A-Meter ASTM C 173, AASHTO T 196
3 Neck cap has a wide sure grip knurled surface for easy thread on and a watertight seal 3 Meter is hard anodized coated for a long lasting corrosion resistant finish Dual fast-acting, one-piece self-locking stainless steel clamps ensure a watertight seal between the top section and bowl. A see through window in the neck has an easy to read engraved scale graduated from 0 to 9% with .25% sub-graduations. Base capacity is 130 cu. in. A durable plastic carrying case with a tough die cut closed cell foam insert protects the meter and its accessories. Kit includes: Meter, carrying case, tamping rod, baffle funnel, strike-off bar, calibration measuring vessel, syringe, 16 oz. measuring cup, spanner wrench and instruction manual. $ CA-0610 Aluminum Roll-A-Meter. . . . . . . . . . . . . . . . . . .
689.00
