Priyankoo Sarmah Assistant Professor Indian Institute

Transcript

Priyankoo Sarmah Assistant Professor Phone Nos. :+91-361-258 -2574 +91-361-258 -2594 Indian Institute of Technology, Guwahati, Guwahati-781 039, Assam, India. Fax Email :+91-361-258-2089 +91-361-258-2599 : [email protected] Date : 24/01/2014 R&D/07/HSS/P/PRS/02/2013-14 NOTICE INVITING QUOTATION FOR SUPPLY & INSTALLATION OF LAPTOP COMPUTER,ALL IN ONE DESKTOP COMPUTER,DYNAMIC CLOSE TALK HEAD WORN MICROPHONE,HEADPHONE,SOUND MIXER,DYNAMIC DOUBLE RIBBON MICROPHONE AND PORTABLE DIGITAL RECORDER FOR THE DEPARTMENT OF HUMANITIES AND SOCIAL SCIENCES (PROJECT NO.HSS/P/PRS/02), IIT GUWAHATI. Quotations for supply of equipments as per details at ANNEXURE-I,II,III,IV,V,VI,VII - in single bid as indicated in the CHECKLIST given below, in sealed covers, are hereby invited so as to reach the undersigned on or before 19 FEBRUARY, 2014. INSTRUCTION TO BIDDERS: Single Bids: (a) In case of single bid quotations will have to be submitted in single bid, in a properly sealed cover; and the address of the firm submitting the quotation and the Officer to whom the quotation is addressed, must appear distinctly on the sealed cover, Further, on the sealed cover the following are to be written: ‘QUOTATION FOR SUPPLY & INSTALLATION OF LAPTOP COMPUTER, ALL IN ONE DESKTOP COMPUTER, DYNAMIC CLOSE TALK HEAD WORN MICROPHONE, HEADPHONE, SOUND MIXER, DYNAMIC DOUBLE RIBBON MICROPHONE AND PORTABLE DIGITAL RECORDER IIT GUWAHATI’. VIDE NIQ NO. R&D/07/HSS/P/PRS/02/2013-14, LAST DATE FOR SUBMISSION 19 FEBRUARY, 2014. NOTE: The bid documents are not transferable and the firm’s seal and signature of the authorized official must appear on all the papers and envelopes submitted. (b)The bid must mention the prices of all items asked for individually and then summed up at last i.e. basic price and other charges such as Packing, Freight, insurance ,Installation & commissioning charge, VAT/Tax etc as applicable; (c) Annual Maintenance Contract (AMC) rate (after expiry of warranty period) is to be clearly indicated – preferably in both comprehensive and non-comprehensive terms, failure to which the offer may not be considered even if it turns out to be at the lowest price. (d) Details of the technical features of the offered equipment along with Standard Technical literature on each of the items offered; (e) Dealership certificate on the offered products in case of dealer/s; (d) List of reputed organizations/Institutions, where similar orders have been executed (copies of the purchase/work orders will have to be enclosed); (e) Up-to-date Sales Tax clearance certificate (for vendors outside the State of Assam)/VAT Registration Certificate indicating also the TIN number (for vendors from within the State of Assam) OF THE FIRM will have to accompany the quotation to be submitted; (f) Details of nature and maximum period of warranty offered by the vendor (g) After Sales Service: The name & address of the nearest available authorized service centre to IIT, North Guwahati, should be stated in the quotation. TERMS & CONDITIONS: (Please note the term ‘both foreign & indigenous’ wherever mentioned means the term is applicable to both foreign & indigenous purchase) 01. Rates :Rates quoted for indigenous items should be on FOR IIT Guwahati, on DOOR DELIVERY basis, with break-ups as per details below (For import items please refer ‘Additional Terms for imported goods’ at clause No. 25 below). Break-ups of cost (a) Basic Price (b) (+) Central Excise Duty, if any (c) (+) VAT/ Central Sales Tax ( On Sub-Total Price, including Excise Duty, if any) (d) (+) Freight & Insurance Charge, if any (e) (+) Installation & Commissioning Charge, if any (f ) Grand Total F.O.R. IIT Guwahati, Price Note: Vague terms like “packing, forwarding, transportation etc. extra” without mentioning the specific amount will not be accepted. Such offers shall be treated as incomplete and rejected. Bidders shall indicate their rates in clear/visible figures as well as in words and shall not alter/overwrite/make cutting in the quotation. In case of a mismatch, the rates written in words will prevail. 02. Validity (Both foreign & indigenous) : Quoted rates must be valid for 120 days. 03. Performance Bank Guarantee(Both foreign & indigenous) : Performance Bank Guarantee(Both foreign & indigenous) : The successful bidder shall furnish an unconditional Performance Bank Guarantee valid till 60 days after the warranty period from a scheduled Bank for 10% of the Purchase Order value within 21 days of placement of order failing which the contract shall be deemed as terminated (APPLICABLE ONLY TO ORDERS COSTING MORE THAN INR 5,00,000.00).That (a)The Vendor shall provide a Certificate of Guarantee guaranteeing LAPTOP COMPUTER, ALL IN ONE DESKTOP COMPUTER, DYNAMIC CLOSE TALK HEAD WORN MICROPHONE, HEADPHONE, SOUND MIXER, DYNAMIC DOUBLE RIBBON MICROPHONE AND PORTABLE DIGITAL RECORDER of the satisfactory operation of the components and against poor workmanship, bad quality of materials used, faulty designs and performance figures given by the Vendor. (b)This guarantee shall be operative for a period of 60 days after the warranty period. The performance guarantee would be to the extent of 10 % of the order value. (c)The Vendor shall at his own cost rectify the defects/replace the items supplied, for defects identified during the period of guarantee (d)While clauses 3(a),3(b) and 3(c) are applicable to all orders worth Rs.5 Lakhs or more, competent authority may take appropriate decisions on exceptional cases. 04. PENALTY FOR DELAYED DELIVERY (for both foreign & indigenous): In the event of delayed delivery, installation & commissioning i.e. after the expiry of the period as agreed by both the parties, the vendor shall be liable for a penalty deduction at a percentage of the value of the undelivered equipment subject to a maximum of 10% (ten percent) as detailed below: @ 1% up to one week; @ 2.5% up to two weeks; @ 5% up to three weeks; @ 10% for four weeks and above For the purpose of this clause, part of the week is considered as a full week. 05. In case of indigenous supplies, the goods should be insured against theft, loss or breakage during transit and insurance charges should not exceed 1% of the cost of material supplied, the rates of Sales Tax, Excise Duty etc. (as applicable) should be clearly indicated. Form C & D is not applicable to us. However, we are exempted from payment of Excise Duty and certificate to this effect can be provided. 06. Penalty for delayed supply(Both foreign & indigenous) :In case of supply order for the SCIENTIFIC EQUIPMENTS/ APPARATUS, the date of delivery should be strictly adhered to otherwise the Director, IITG reserves the right not to accept delivery in part or full and claim liquidated damages of 1% per week subject to maximum of 10% of the total value of supply 07. Pre-installation requisites(Both foreign & indigenous) : Pre-installation requisites (electrical/floor/space/airconditioning etc.) if any should invariably be mentioned clearly. Installation/ Training will be the full responsibility of the supplier/ Indian Agent. 08. Short Shipment(Both foreign & indigenous) :If any short-shipment etc. is noticed, the same will be arranged immediately with all charges to this effect to be born by supplier/Indian agent. 09 Genuine Pricing (Both foreign & indigenous) :Vendor is to ensure that quoted price is not more than the price offered to any other customer in India to whom this particular item has been sold, particularly to IIT/Institutes and other Government Organization. Copy of the latest price list for the quoted item, applicable in India, must be enclosed with your offer. 10. Excise Duty:The Institute is exempted from payment of Central Excise Duty vide GOI Notification No. 10/97-Central Excise, dated 01.03.97 with Regn.No. TU/V/RG-CDE(351)/2011, DATED 19.09.2011. 11. VAT:For a vendor within the State of Assam, appropriate VAT (to be deducted at source) will be applicable. For exemption from Octroi, wherever required, the Institute will issue necessary certificates. 12. Entry Tax :Assam Govt. Entry Tax – usually @4% [to be paid by IIT Guwahati, not by the vendor], wherever applicable, will be added while evaluating cost status of the concerned equipment to be supplied by vendors from outside the State of Assam. 13. Delivery : (a)Delivery of goods at IIT Guwahati, will have to be maximum within 45(Forty-five) days from the date of issue of the Purchase Order. (b)Safe delivery of goods: All aspects of safe delivery shall be the exclusive responsibility of the vendor. At the destination site, the cartons will be opened only in the presence of IIT user/representative and vendor's representative and the intact position of the seal for not being tempered with, shall form the basis for certifying the receipt in good condition. (c) No Part Delivery : part shipment will not be allowed. 14. Mode of Payment for Indigenous Purchase(For import items please refer „Additional Terms for imported goods‟ clause No.28 below) : (1)Payment for Indigenous Purchases will be maximum within 45 days from the date of successful delivery and installation of goods at IIT Guwahati, North-Guwahati, generally through A/c payee cheque. In case payment is to be made by DD, the Draft commission will be deducted from the bill amount. or (2) Payment through bank against proof of dispatch: 90% payment shall be released on receipt of proof of dispatch through State Bank of India, IIT Guwahati Branch, Guwahati, Assam. Balance 10% shall be released after installation /handing over of the equipment to the consignee(s). Note: Please note as per Institute‟s norm advance payment is not allowed for indigenous purchase. 15. Quotation by Fax/Mail not Acceptable(Both foreign & indigenous) :The offers submitted by telex/ telegram/ fax/ E-mail etc. shall not be considered. No correspondence will be entertained on this matter. 16. Late and delayed tender(Both foreign & indigenous) :Late and delayed tender will not be considered. In case any unscheduled holiday occurs on prescribed closing/opening date the next working day shall be the prescribed date of closing/opening. 17. Conditional tenders not acceptable(Both foreign & indigenous) : Conditional tenders shall not be accepted on any ground and shall be rejected straightway. In other word, printed conditions mentioned in the tender bids submitted by vendors will not be binding on IITG. All the terms and conditions for the supply, payment terms, penalty etc. will be as those mentioned herein and no change in the terms and conditions by the vendors will be acceptable. 18. Specifications are basic essence of the product (Both foreign & indigenous) : It must be ensured that the offers are strictly as per our specifications. At the same time it must also be kept in mind that merely copying our specifications in their quotation shall not make firms eligible for consideration. A quotation has to be supported with the printed technical leaflet/literature (wherever applicable) and the specifications mentioned in the quotation must be reflected/ supported by such printed technical leaflet/literature model quoted/tendered specifications should invariably be highlighted in the leaflet/literature for easy reference. 19. Enquiry during the course of evaluation not allowed(Both foreign & indigenous) : No enquiry shall be made by the bidder(s) during the course of evaluation of the tender till final decision is conveyed to the successful bidder(s). However, the Committee/its authorized representative and office of IIT GUWAHATI can make any enquiry/seek clarification from the bidders. In such a situation, the agency shall extend full co-operation. The bidders can also be asked to arrange demo. of the offered items, in a short period notice, as such the bidders have to be ready for the same. 20. The acceptance of the quotation(Both foreign & indigenous) will rest solely with the Director, IITG, who in the interest of the Institute is not bound to accept the lowest quotation and reserves the right to himself to reject or partially accept any or all the quotations received without assigning any reasons. 21. Force Majeure(Both foreign & indigenous) : (a) If the performance of the obligation of either party is rendered commercially impossible by any of the events hereafter mentioned that party shall be under no obligation to perform the agreement under order after giving notice of 15 days from the date of such an event in writing to the other party, and the events referred to are as follows: I) any law, statute or ordinance, order action or regulations of the Government of India. II) Any kind of natural disaster and III)Strikes acts of the Public enemy, war, insurrections, riots, lockouts, sabotage. 22. Termination for default(Both foreign & indigenous) : Default is said to have occurred If the supplier fails to deliver any or all of the services within the time period(s) specified in the purchase order or any extension thereof granted by IIT. If the supplier fails to perform any other obligation(s) under the contract If the vendor, in either of the above circumstances, does not take remedial steps within a period of 30 days after receipt of the default notice from IIT (or takes longer period in-spite of what IIT may authorize in writing), IIT may terminate the contract / purchase order in whole or in part and forfeit the EMD/PBG as applicable. In addition to above, IIT may at its discretion also take the following actions: IIT may procure, upon such terms and in such manner, as it deems appropriate, goods similar to the undelivered items/products and the defaulting supplier shall be liable to compensate IIT for any extra expenditure involved towards goods and services obtained. 23. Applicable Law(Both foreign & indigenous) : (a)The contract shall be governed by the laws and procedures established by Govt. of India and subject to exclusive jurisdiction of Competent Court and Forum in Guwahati, India only. (c). Any dispute arising out of this purchase shall be referred to the Director IIT Guwahati, and if either of the parties hereto is dissatisfied with the decision, the dispute shall be referred to the decision of an Arbitrator, who should be acceptable to both the parties, to be appointed by the Director of the Institute. The decision of such Arbitrator shall be final and binding on both the parties. ADDITIONAL TERMS FOR IMPORTED GOODS Following terms besides the fore mentioned terms will be applicable in case of foreign purchases : 24. Rates :Quoted rates should be in CIF/CIP Kolkata terms and charges to be stated in the following break-ups (a) Ex-works value (b) + Documentation & Handling Charge, if any (c) + Estimated Overseas Freight to be paid at actual against authentic documents and monetary receipt (d) + Estimated Overseas Insurance Charge to be paid at actual against authentic documents and monetary receipt (In case the firm holds open insurance policy, the Insurance Certificate relating to the consignment will have to be provided). (e) Total CIP/CIF Kolkata value 25. After Sales Service: In case of imported stores, foreign manufacturing firms should indicate facilities available for after sales service in India without which their offers are liable to be ignored. 26. Delivery : (a)Delivery of goods at IIT Guwahati, will have to be maximum within 95(ninety-five) days from the date of issue of the Purchase Order. (b)Delivery at kolkata Airport only: As we do not have clearing agent in any other Airport/Seaport, delivery is to be made only at Kolkata . (c)While transshipment will be allowed, part shipment will not be allowed. 27. Payment : (a).Above $10,000.00: By an irrevocable letter of Credit at CIF/CIP Kolkata value negotiable through any overseas branch of Axis Bank Ltd with unrestricted provision. (b)Below $10,000.00 by FDD/Wire Transfer as given below: (i) Advance payment Against Bank Guarantee: 90% of the price will be paid in advance against equivalent bank guarantee from a scheduled bank provided by the supplier/Indian Agent. The remaining 10% shall be released only after receipt and acceptance of materials in good condition or after satisfactory installation and commissioning of the equipment. or (ii) Payment Against Proof of Despatch: 90% of the price will be paid against receipt of proof of dispatch such as AWB, Invoice, Packing List, Insurance certificate, etc.. The remaining 10% shall be released only after receipt and acceptance of materials in good condition or after satisfactory installation and commissioning of the equipment. or (iii) 100% Payment Basis: On request by the supplier/s 100% payment by FDD will be made. In this case on receipt of your Order Acknowledgement an FDD will be established for total ordered value, thereupon, a Xerox copy of the FDD will be sent to you which will enable you to send the materials. On satisfactory receipt and acceptance of the materials or satisfactory installation and commission of the equipment the Original FDD will be sent to you. Note:Please note FDD/LoC will not be opened unless and until Letter of Acknowledgement in original is received at IIT Guwahati, directly from the principal (Even in case of firms having subsidiary office in India). The Indian agents are therefore advised to submit quotation after consultation with their respective principals). 28. Customs Duty :The Institute is generally exempted from payment of Customs Duty vide GOI Notification No.51/96-Customs, dated 23.07.96, with Regn. No. TU/V/RG-CDE(351)/2011, DATED 19.09.2011. [CUSTOMS DUTY EXEMPTION CERTIFICATE WILL BE MADE AVAILABLE BY THE INSTITUTE IN REGARD TO QUOTES IN FOREIGN CURRENCY ONLY [ NOT AGAINST QUOTES MADE BY A FIRM IN INDIAN CURRENCY, UNLESS THE CONCERNED FIRM IS A FOREIGN HOLDING COMPANY WITH `FDI’ CERTIFICATE ISSUED BY THE MINISTRY OF FINANCE, GOVT. OF INDIA ]. 29. Agency Commission: The percentage of ex-works value to be paid to Indian agent in equivalent Indian currency as agency commission as applicable will have to be clearly stated in the quotation. 30. After Sales Service : For equipment to be imported the quotation will have to clearly state the available nearest after sales service centre and contact no. in India. 31. Country of Origin : While Country of Origin Certificate will not be insisted, the same however will have to be stated in the Original Invoice for payment through LoC. 32. LoC Amendment : LoC/FDD amendment charges due to mistake on the part of the supplier, if any, will have to be borne by the supplier. Name : Priyankoo Sarmah, PI Designation : Assistant Professor Address : Department of HSS, Academic Complex Block-F, IIT Guwahati, 781039, Assam Encl.: ANNEXURE- I ANNEXURE- II ANNEXURE- III ANNEXURE- IV ANNEXURE- V ANNEXURE- VI ANNEXURE- VII ANNEXURE I Detailed Technical Specifications for Laptop Computer Item Name: Quantity: Processor Memory Weight Connections Communications Audio Graphics Storage Display Laptop Computer 01(One only) 2.0GHz quad-core Intel Core i7 (Turbo Boost up to 3.4GHz) with 6MB shared L3 cache 8GB of 1600MHz DDR3L Less than 2.5 KG SDXC card slot, MagSafe 2 power port, Two USB 3 ports (up to 5 Gbps), Two Thunderbolt ports (up to 10 Gbps), Headphone port, HDMI port 802.11ac Wi‑Fi wireless networking;3 IEEE 802.11a/b/g/n compatible and Bluetooth 4.0 wireless technology Headphone port, Stereo speakers and Dual microphones Intel Iris Pro Graphics 256 GB 15 inch, LED-backlit ANNEXURE II Detailed Technical Specifications for All in One Desktop Computer Item Name: Quantity: Processor Memory Storage Graphics Display Audio Connections Input Networking Weight Electrical and operating requirements All In One Desktop Computer 01 3.2GHz quad-core Intel Core i5 processor (Turbo Boost up to 3.6GHz) with 6MB L3 cache 8GB (two 4GB) of 1600MHz DDR3 memory; four user-accessible SO-DIMM slots 1TB (7200-rpm) hard drive NVIDIA GeForce GT 755M graphics processor with 1GB of GDDR5 memory 27-inch (diagonal) LED-backlit display with IPS technology; 2560x1440 resolution with support for millions of colours Stereo speakers Dual microphones Headphone port Headphone/optical digital audio output (mini-jack) SDXC card slot Four USB 3 ports Two Thunderbolt ports Mini Display Port output with support for DVI, VGA and dual-link DVI (adapters sold separately) 10/100/1000BASE-T Gigabit Ethernet (RJ-45 connector) Kensington lock slot Keyboard: Full-size keyboard with 12 function keys, Mouse: Seamless Multi-Touch surface with support for simple gestures (scrolling and swiping). Ambidextrous construction 802.11n Wi-Fi wireless networking; 2 IEEE 802.11a/b/g compatible Bluetooth 4.0 wireless technology Less than 12 kg Line voltage: 100-240V AC Frequency: 50Hz to 60Hz, single phase Operating temperature: 10° to 35° C (50° to 95° F) ANNEXURE III Detailed Technical Specifications for Dynamic, Close talk head worn microphone Item Name: Quantity: Type: Transducer Type : Polar Pattern: Frequency Response: Sensitivity (1 kHz): Dynamic, Close talk head worn microphone 04 (Four only) Head worn Dynamic Cardioid 50 Hz - 15 kHz 65 dBV/Pa / 0,45 mV/Pa ANNEXURE IV Detailed Technical Specifications for Headphone Item Name Quantity Transducer Type Driver size Sensitivity Impedance Max. input power Frequency range Net weight (without cable) Cable length Type of cable Plug Headphone 04(Four only) Dynamic, Neodym-Magnet 40 mm 101 dB SPL/mW 37 Ω 1000 mW 15 Hz – 27 kHz Less than 500 g Less than 2.5 m Dual-exit, detachable oxygen-free copper Gold-plated 1/8” (3.5 mm) stereo mini jack ANNEXURE V Detailed Technical Specifications for Sound Mixer Item Name: Sound Mixer Quantity: 01 FEATURES: Each mono channel has an Onyx mic preamp, phantom ■ 8-channel premium analog mixer with integrated power, an input Gain control with 60 dB of gain, a sharp 24-bit / 96 kHz FireWire I/O 18 dB/octave, 75 Hz Low Cut filter, Pan, Mute, Solo and one Channel Insert jack for external processor connection. ■ Three Onyx boutique quality mic preamps, built-in DIs on the first two channels ■ 3-band Perkins EQ with sweepable mids on mic/line connection of dedicated talkback channels section ■ 3-band Perkins EQ on stereo line channels. ■ Hybrid mono/stereo channel with 4-band Perkins EQ Other features include a stereo tape input and output, a 1/4-inch stereo headphone jack, stereo 12segment LED ■ 8x2 FireWire routing, including aux sends, main meters and XLR and TRS stereo output jacks. L/R and pre/post EQ assignment for all channels ■ Stereo playback from DAW ■ Built-in DI on first two channels ■ Individual 48V phantom power switches on all mic inputs ■ Talkback section with built in mic and flexible routing Noise Characteristics: Equivalent Input Noise (EIN), mic input at insert, ISO nsource impedance, 20 Hz to 20 kHz 60 dB (max) gain: -127 dBu 40 dB gain: -126.5 dBu Equivalent Input Noise (EIN), mic input at insert, 50 nsource impedance, A-weighted 60 dB (max) gain: -130.5 dBu 40 dB gain: -130 dBu Output Noise Figure (1/4” Main out, all channels assigned to main, Gain knobs at unity, 20 Hz to 30 kHz) Main Mix knob down, channel Level knobs down: -107 dBu (-Ill dB SNR, ref +4 dBu) Main Mix knob unity, channel Level knobs down: -95.5 dBu (-99.5 dB SNR, ref +4 dBu) Main Mix knob unity, channel Level knobs unity: -91.5 dBu (-95.5 dB SNR, ref +4 dBu) FireWire Through (Record + Playback) Dynamic Range: (0 dBu in, mic input to FireWire send, returned to Control Room, all gain stages at unity, 20 Hz to 20 kHz) 44.1 kHz sample rate: -104 dB 96 kHz sample rate: -106.5 dB Frequency Response: Mic input to any output (all gain stages at unity, +0/-0.5 dB) 20 Hz to 20 kHz Stereo channel line input to any output (all gain stages at unity, +0/-0.5 dB) 20 Hz to 20 kHz FireWire in and out (mic input to FireWire send, returned to Control Room, all gain stages at unity): 44.1 kHz sample rate (+0 1-0.5 dB) 20 Hz to 20 kHz -3 dB at 21 kHz 96 kHz sample rate (+0/-0.5 dB) 20 Hz to 20 kHz -3 dB at 45 kHz Distortion(THD+N): (20 Hz to 20 kHz bandwi~th Mic input at insert (+4 dBu in, 0 dB gain, +4 dBu out) 0.001 % Mic input at insert (-36 dBu in, +40 dB gain, +4 dBu out) 0.007% Stereo channel line input to any output (+4 dBu in, all gain stages at unity, +4 dBu out) 0.005% FireWire in and out (+4 dBu in, mic input to FireWire send, returned to Control Room, all gain stages at unity) 44.1 kHz sample rate: 0.01 %, 20 Hz to 2 kHz 0.02%,2 kHz to 20 kHz 96 kHz sample rate: 0.0 1%, 10Hz to I kHz 0.03%, I kHz to 47 kHz Attenuation and Crosstalk: @I kHz Main Mix knob down -80 dBu Channel Altl/Mute switch engaged -90 dBu Channel Level knob down -80 dBu Common Mode Rejection Ratio (CMRR): Mic input to insert, max gain, I kHz -70 dB Maximum Input Levels: Mic input, gain at min (0 dB) +22 dBu Mic input, gain at max (60 dB) -38 dBu Line input, gain at -20 dB +22 dBu Instrument input, gain at -20 dB +22 dBu Tape input +12 dBu Aux return +22 dBu Maximum Output Levels: All outputs +22dBu Equalization: Mono Channels Low: ±15 dB @ 80 Hz Mid frequency: 100 Hz to 8 kHz Mid gain: ±15 dB High: ±15 dB @ 12 kHz Hybrid Channel Low: ±15 dB @ 80 Hz Low Mid: ±15 dB @ 400 Hz High Mid: ±15 dB @ 2.5 kHz High: ±15 dB @ 12kHz Stereo Channels Low: ±15 dB @ 80 Hz Mid: ±15 dB @ 2.5 kHz High: ±15 dB @ 12 kHz FireWire: Sample Rates Available 44.1 kHz, 48kHz, 88.2kHz, 96kHz Buffer Size 32(44. 1kHz and 48kHz only), 64, 128,256,512,1024,2048 samples 24- bit Resolution Meters: 2-segment pre-fader channel meters OL (+ 18 dBu), -20 dBu 12-segment pre-fader Control Room meters OL (+20 dBu), +15, +10, +6, +3, 0, -2, -4, -7, -10, -20,30 (0 dB = 0 dBu) Input Impedance: Mic input 2.8 Ω k balanced Hi-Z input I M Ω unbalanced Mono channel line input: 30 Ω k balanced 15 Ω k unbalanced Stereo channel line input: 20 Ω k balanced 10 Ω unbalanced Output Impedance Main XLR output: 100 Ω balanced Phones output: 75 Ω All other outputs: 300 Ω ANNEXURE VI Detailed Technical Specifications for Dynamic double ribbon microphone Item Name: Dynamic double ribbon microphone Quantity:01(one only) Transducer type: Dynamic Operating principle: Pressure gradient Frequency response: 40 - 18,000 Hz Polar pattern: Hypercardioid Rear attenuation at 1 kHz : > 25 dB at 110° Open circuit voltage at 1 kHz (0 dB = 1 V/Pa) 1.0 mV/Pa = -60 dBV Nominal impedance: 200 Ω Load impedance: ≥ 1000 Ω Diaphragm: aluminum Case/finish: Brass Connector: 3-pin XLR male Dimensions: Length: 156 mm Shaft diameter: 23 mm Head diameter: 38 mm Weight without cable: 156 g ANNEXURE VII Detailed Technical Specifications for Portable Digital Recorder Item name: Portable digital recorder Quantity: 04(Four only) Recording Media: SD card（64MB～2GB), SDHC card (4GB～32GB) File Format: WAV, MP3 Recording/Playback Format: WAV 44.1/48/96 (HS mode) kHz, 16/24-bit Number of Channels: 2 channels (stereo) Analog Input: MIC/LINE 1 IN (XLR), 1/8"（3.5mm）stereo mini jack Analog Output: LINE OUT 1/8"（3.5mm）stereo mini jack Headphone Output: 1/8"（3.5mm）stereo mini jack Power Supply: Lithium-ion rechargeable battery Frequency response: 20-20000 Hz Computer Requirements: Windows OS Windows XP, Macintosh OS Mac OS X 10.2 or later USB Port: USB2.0 recommended