Transcript
Operating Instructions
11 BAND™ HIGH-PERFORMANCE RADAR/LASER DETECTOR WITH XTREME RANGE SUPERHETERODYNE™ TECHNOLOGY
PRO 9480 Nothing comes close to a Cobra®
Printed in China Part No. 480-133-P
English
Introduction
Important Information And Customer Assistance
Important Information Federal Laws Governing The Use Of Radar Detectors It is not against federal law to receive radar transmissions with your Cobra radar/ laser detector. The Communications Act of 1924 guarantees your right to receive radio transmissions on any frequency. Local laws that contravene this Act, while illegal, may be enforced by your local law enforcement officials until and unless they are prohibited from doing so by federal court action.
•
Safety Alert Use of this product is not intended to, and does not, ensure that motorists or passengers will not be involved in traffic accidents. It is only intended to alert the motorist that an emergency vehicle equipped with a Cobra Safety Alert transmitter is within range as defined by that product. Please call local fire and police departments to learn if coverage exists in your area. Safe Driving Motorists, as well as operators of emergency or service vehicles, are expected to exercise all due caution while using this product, and to obey all applicable traffic laws. Security Of Your Vehicle Before leaving your vehicle, always remember to conceal your radar detector in order to reduce the possibility of break-in and theft.
Customer Assistance
Customer Assistance
•
Should you encounter any problems with this product, or not understand its many features, please refer to this owner’s manual. If you require further assistance after reading this manual, Cobra Electronics offers the following customer assistance services: For Assistance In The U.S.A. Automated Help Desk English only. 24 hours a day, 7 days a week 773-889-3087 (phone). Customer Assistance Operators English and Spanish. 8:00 a.m. to 6:00 p.m. CT Mon. through Fri. (except holidays) 773-889-3087 (phone). Questions English and Spanish. Faxes can be received at 773-622-2269 (fax). Technical Assistance English only. www.cobra.com (on-line: Frequently Asked Questions). English and Spanish.
[email protected] (e-mail). For Assistance Outside The U.S.A. Contact Your Local Dealer A1 English
©2004 Cobra Electronics Corporation 6500 West Cortland Street Chicago, Illinois 60707 USA www.cobra.com
Controls, Indicators And Connections
Introduction
Controls, Indicators And Connections Windshield Bracket Release Button
Display And Product Features
Introduction
•
Display
Windshield Bracket Mount
X K Ka V S LaserEye For 360° detection of laser and strobe signals. Speaker City Button For City or Highway modes to reduce false alerts.
12V DC Power Jack On-Off/ Volume Control Allows you to adjust the volume of the tone alerts.
IntelliMute Button Engine RPM sensing mute function which reduces false alerts. Button turns IntelliMute On and Off. (Also enters IntelliMute setting mode.*)
Mute Button For manual mute or auto mute of audio alerts. (Also turns Voice Alert On and Off.*)
Dim Button Allows you to adjust the UltraBright Data Display brightness for easy reading. (Also turns VG-2 and Spectre 1 alerts On and Off.*)
WARNING
* Press and hold for two (2) seconds to access these functions.
A2 English
Modifications or parts substitutions not approved by Cobra Electronics Corporation may violate FCC Rules and void your authority to operate this equipment.
Introduction
•
Introduction Important Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1 Customer Assistance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A1 Controls, Indicators And Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . A2 Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3 Product Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . A3
Signal Strength, Laser And City/ Highway Mode Indicators Signal Strength 1 (weakest) to 5 (strongest)
L IntelliMute Indicator
Radar, VG-2, Spectre 1, Safety And Strobe Indicators
NOTE: In This Manual When steady, X K Ka V S the display will be shown:
c
When blinking, the display will be shown:
c
X K Ka V S
Product Features
Your Detector Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Getting Started . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Highway/City Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 UltraBright Data Display Brightness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Muting An Alert . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Auto Mute Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 IntelliMute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Voice/Tone Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 VG-2 And Spectre 1 Alert Audio Settings . . . . . . . . . . . . . . . . . . . . . . . . 13 Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Signals Detected . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Audio Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Visual Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 Instant-On Detection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Responding To Alerts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 Understanding Radar And Laser . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18 Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
•
Congratulations! You’ve made a smart choice by purchasing the PRO 9480 high performance radar/laser detector from Cobra. Just look at some of the sophisticated features and capabilities your new unit includes: Xtreme Range UltraBright Data Display Superheterodyne Technology Easy-to-read with adjustable brightness With super-fast sweep circuitry, City Or Highway XRS provides extra detection range Modes to reduce false alerts and the best possible advance warning Safety Alert to even the fastest radar guns Traffic warning system distinguishes Detection And Separate Alerts For: important safety alerts from other Radar signals (X, K and Ka bands, K band signals with signal strength indicated), Strobe Alert laser signals, Safety Alert signals, Emergency vehicle warning system Strobe Alert signals, VG-2 signals, Manual Mute Or Auto Mute Spectre 1 signals A mute function of audio alerts LaserEye IntelliMute For 360° detection of laser and A mute function which strobe signals automatically reduces false Instant-On Ready alerts by sensing engine RPMs Detects radar guns with “instant-on” Mounting (very fast) speed monitoring capabilities Mounts easily on windshield Tone Alert or Voice Alert or dashboard With adjustable volume This booklet describes the simple steps for mounting and setting up your detector. It also provides helpful information about how radar and laser guns are used and how you can interpret the alerts you receive.
Nothing comes close to a Cobra®
Table Of Contents
Warranty Limited 1-Year Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Customer Assistance Product Service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Trademark Acknowledgement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 Optional Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24 Order Form . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
A3
Nothing comes close to a Cobra®
1
Your Detector
Installation
Your Detector
Installation Where To Mount Your Unit
•
You will get optimum performance from your detector if you Mount it at a point approximately in the center of the vehicle, as low as possible on the front windshield without obstructing the unit’s view of the road either to the front or rear. You can also mount it directly on the dashboard. Windshield Mounting
Dashboard Mounting
Installation
Windshield Mounting
1. Attach the rubber cups to the bracket.
2. Make sure the rubber cups and your windshield are clean. 3. Push the bracket firmly onto the windshield.
The unit’s lens must not be blocked and the LaserEye should have a clear view out the back window to allow 360° detection. The LaserEye Should Have A Clear View
4. Attach the detector to the bracket. Check the angle of the unit.
5. To adjust the angle if necessary, gently push or pull on the bracket to bend it. DO NOT use the detector to bend the bracket. 6. Plug the power cord into the detector.
Radar and laser signals pass through glass but not through other materials and objects. Objects that can block or weaken incoming signals include:
2
■
Windshield wiper blades
■
Mirrored sun screens
■
Dark tinting at the top of the windshield
■
Heated windshields currently available on some vehicles (Instaclear for Ford, Electriclear for GM.) Consult your dealer to see if you have this option.
English
7. Plug the cigarette lighter adapter on the power cord into your vehicle’s cigarette lighter. 8. You can temporarily remove the detector whenever you wish by pressing the bracket release button and sliding it off the bracket.
Nothing comes close to a Cobra®
3
Your Detector
Installation
Getting Started And Settings
Your Detector
Getting Started
Dashboard Mounting
•
1. Place the detector on the dashboard to find a location where the unit has a clear, level view of the road. The angle can NOT be adjusted after mounting.
X K Ka V S
h
On-Off/ Volume Control Rotate clockwise (away from you)
ns
ary
Ico
nd
co
3. Attach the pad to the dashboard at your chosen location and remove the other paper backing.
Power On
Se
2. Remove the paper backing from one (1) side of the hook-and-loop fastener.
To Turn On The Unit And Adjust The Audio Volume Rotate the On-Off/ Volume control clockwise (away from you).
4. Attach the detector to the hook-and-loop fastener. You can remove and reattach the unit as often as you like.
Tone
Voice
Visual Display
Three (3) beeps
Testing, then three (3) beeps
h
appears in the display indicating System Ready, then that the power is On. Voice Alert
NOTE In some vehicles, power is supplied to the cigarette lighter even while the ignition is Off. If this is the case with your vehicle, you should turn Off or unplug your detector when parking for lengthy periods.
6. Plug the power cord into the detector.
Settings 7. Plug the cigarette lighter adapter on the power cord into your vehicle’s cigarette lighter.
4
English
When changing the Settings on your detector, please keep in mind: ■
Buttons can have multiple functions.
■
Depending on your choice of Voice Alert or Tone Alert mode, you will hear either voice messages or tones confirming changes in settings.
■
All settings will be stored in memory when the power is turned Off and recalled when the power is turned back On.
•
Nothing comes close to a Cobra®
5
Settings
Your Detector
Settings
Your Detector
Highway/City Mode
UltraBright Data Display Brightness
Setting your detector to City mode delays all X band audio alerts until the signal strength reaches Level 3. (A single beep will sound when the signal is first detected.) This will reduce false alerts while you are driving in, or near, urban areas where there are many sources for conflicting X band signals such as microwave towers and automatic door openers.
You can choose from three (3) settings for Brightness of the display. You can cycle through the settings by repeatedly pushing the Dim button. The factory setting is Bright.
To change settings, follow the procedure listed below, which indicates what you will see and hear (either in Voice Alert or Tone Alert mode) as you complete each step. The factory setting is Highway mode.
Bright Press and
Dark release Dim button
Dim Highway Mode
X K Ka V S
h
To Change The Brightness To Dim
City Mode
X K Ka V S
Press and release the Dim button once.
c City Button Press and release
Press and release the City button.
Tone
Voice
Visual Display
One (1) beep
City
c appears in the display
To Change From City Mode back To Highway Mode Press and release Tone the City button again. Two (2) beeps
Voice
Visual Display
One (1) beep
Dim
Display dims
Press and release the Dim button again.
Tone
Voice
Visual Display
One (1) beep
Dark
Display remains dim (no visual alerts will be seen)
Tone
Voice
Visual Display
Two (2) beeps
Bright
Display returns to full brightness
To Change The Brightness To Bright
Voice
Visual Display
Highway
h appears in the display
English
Tone
To Change The Brightness To Dark
To Change From Highway Mode To City Mode
6
Dim Button Press and release
Press and release the Dim button a third time.
Nothing comes close to a Cobra®
7
Your Detector
Settings
Settings
Your Detector
Muting An Alert
IntelliMute
Your detector allows you to quickly turn Off an audio Alert by momentarily pressing the Mute button. If you press the Mute button a second time during the Alert, the audio Alert will be turned back On.
IntelliMute is a unique new feature that allows you to avoid alerts you don’t need to hear because you are stopped or moving slowly. By sensing the “revs” (RPMs) of your engine, IntelliMute knows when you are at low speed and automatically mutes alerts (except for strobe signals from emergency vehicles).
Auto Mute Mode Auto Mute will automatically reduce the audio volume of all alerts after four (4) seconds for as long as the signal is detected. The factory setting for Auto Mute is On.
Before IntelliMute will work, you must set an activation point for your engine’s revs (see page 11). Whenever the revs are below that point, IntelliMute will begin muting. The activation point will be stored in memory and recalled each time the power is turned On. The factory setting is IntelliMute Off. NOTE IntelliMute may not work with some vehicles because it cannot sense the engine’s revs. In such cases, you can reduce unwanted audio alerts by using Auto Mute and City mode when appropriate.
Mute Button Press and release IntelliMute On
X K Ka V S
To Turn Auto Mute Off Press and release the Mute button while no alert is occurring.
Tone
Voice
Visual Display
One (1) beep
Auto Mute Off
None Press and release the IntelliMute button.
Tone
Voice
Visual Display
Two (2) beeps
Auto Mute On
None
English
Tone
Voice
Visual Display
Two (2) beeps
IntelliMute On
Dot appears next to the large character on the right
Tone
Voice
Visual Display
One (1) beep
IntelliMute Off
None
To Turn IntelliMute Off Press and release the IntelliMute button again.
8
IntelliMute Button Press and release
To Turn IntelliMute On
To Turn Auto Mute On Press and release the Mute button again while no alert is occurring.
c
Nothing comes close to a Cobra®
9
Settings
Your Detector
Your Detector
What To Remember While Using IntelliMute IntelliMute works with both City and Auto Mute modes. Whenever your engine revs are below the activation point, the dot next to the large character on the right side of the display will remain lit. Above the activation point, the dot will blink twice every two (2) seconds. Below Activation Point
X K Ka V S
L
Above Activation Point
X K Ka V S
L
If, for any reason, the unit stops sensing your engine’s revs, IntelliMute will indicate an error and automatically turn Off. The rev point you set will be stored in the unit’s memory when power is turned Off and recalled each time the power is turned On. NOTE The rev point must be reset if you use your detector in a different vehicle. NOTE When initially choosing your IntelliMute activation point, a setting of approximately 300 to 600 RPMs above idle is recommended. You can reset the activation point at any time to fit your individual preferences and driving style. Setting The IntelliMute Activation Point Your detector must be installed in your vehicle. CAUTION Do not attempt to set the rev point while driving. Your vehicle should be parked and idling.
Settings IntelliMute Button Press and hold for two (2) seconds
To Set The IntelliMute Activation Point Tone
Voice
Visual Display
Two (2) beeps
Set Engine Revs
None
Rev your engine to None the level you wish to set (recommend slightly above idle) and hold revs steady for two (2) seconds.
None
Three (3) bars will flash in succession
At the desired rev level, press and release the IntelliMute button.
IntelliMute Set
Press and hold the IntelliMute button for two (2) seconds.
1
Three (3) beeps
2
3
All three (3) bars flash three (3) times
1
2
3
NOTE If the unit is unable to sense usable pulses within three (3) seconds or if you do not set a rev point within 20 seconds of beginning these steps, IntelliMute will indicate an error and automatically turn Off. Tone
Voice
Visual Display
Four (4) beeps
IntelliMute Error, followed by
E appears
IntelliMute Off
X K Ka V S
E
IntelliMute must be turned On before setting the activation point. Depending on whether the unit is in Tone Alert or Voice Alert mode, you will hear a series of beeps or voice messages as you follow the steps on page 11. 10 English
Nothing comes close to a Cobra®
11
Your Detector
Settings
Settings
Your Detector
Voice/Tone Setting
VG-2 And Spectre 1 Alert Audio Settings
You can set your detector to sound alerts with either a Voice or a Tone. You can change settings by using the Mute button.
The detector is undetectable by police VG-2 and Spectre 1 radar detector detectors and will alert you when such a device is in use near your vehicle. During the alert, the unit continues to detect other signals. You can choose whether or not you want your unit to show VG-2 and Spectre 1 alerts. The factory setting is VG-2 and Spectre 1 alert On.
In Voice Alert mode, you will first hear several tones, then a voice message announcing the type of signal detected, followed by more tones. In Tone Alert mode, you will hear the tones only. The factory setting is Voice Alert mode.
On/Off Indicator
X K Ka V S
c Dim Button Press and hold for two (2) seconds
Mute Button Press and hold for two (2) seconds
To Turn VG-2 And Spectre 1 Alerts Off To Change From Voice Alert To Tone Alert While no signal is being detected, press and hold the Mute button for two (2) seconds.
Tone
Voice
Visual Display
One (1) beep
Tone Alert
None
While no signal is being detected, press and hold the Dim button for two (2) seconds.
Tone
Voice
Visual Display
One (1) beep
Spectre VG-2 Off
V will blink once in the display
To Turn VG-2 And Spectre 1 Alerts On To Change From Tone Alert Back To Voice Alert While no signal is being detected, press and hold the Mute button for two (2) seconds again.
12 English
Tone
Voice
Visual Display
None
Voice Alert
None
While no signal is being detected, press and hold the Dim button for two (2) seconds again.
Tone
Voice
Visual Display
Two (2) beeps
Spectre VG-2 On
V will blink twice in the display
Nothing comes close to a Cobra®
13
Detection
Your Detector
Detection
Your Detector
Detection Signals Detected
•
The tables on the following pages show you the types of Signals your detector will detect, as well as the voice and visual alerts it provides for each of them.
During Safety Alert and Strobe Alert the letter S will appear. It will be steady during a Safety Alert and will blink during a Strobe Alert. Safety Alert Signal Detected
X K Ka V S
Strobe Alert Signal Detected
c
X K Ka V S
c
Audio Alerts In Voice Alert mode you will first hear several tones, then a voice message announcing the type of signal detected, followed by more tones. In Tone Alert mode, you will hear the tones only. In both Voice Alert and Tone Alert modes, a distinctly different alert tone is used for each type of signal detected (including separate tones for each laser signal). For X, K and Ka band radar signals, the tones will repeat faster as you approach the signal source. The repeat rate of the tones gives you useful information about the signal detected. (See responding to alerts on page 17.)
Visual Display An indication of the type of signal detected will appear in the UltraBright data Display. During X, K and Ka alerts, a number will also appear, indicating the strength of the signal detected. (1 = weakest, 5 = strongest) X Signal Detected
X K Ka V S
2
K Signal Detected
X K Ka V S
3
X K Ka V S
5
Laser Signal Detected
L
During VG-2 or Spectre 1 alerts, the letter V will appear. It will be steady during VG-2 and blink during Spectre 1. VG-2 Alert Signal Detected
Type of Signal
Voice
Visual Display
X Band Radar
X Alert
X and Signal Strength
K Band Radar
K Alert
K and Signal Strength
Ka Band Radar
Ka Alert
Ka and Signal Strength
X Signal Detected
X K Ka V S
c
3
X K Ka V S
5
Type of Signal
Voice
Visual Display
LTI 20-20*
Laser Alert
L is Steady
LTI Ultra-Lyte*
Laser Alert
L is Steady
Kustom Signals ProLaser*
Laser Alert
L is Steady
Kustom Signals ProLaser III*
Laser Alert
L is Steady
* Your detector provides 360˚ detection of these signals. Laser Signal Detected
Spectre 1 Alert Signal Detected
X K Ka V S
X K Ka V S
Ka Signal Detected
Laser Signals, Voice And Visual Displays
X K Ka V S X K Ka V S
2
K Signal Detected
Ka Signal Detected
During laser alerts the letter L will appear, instead of the signal strength indication.
X K Ka V S
Radar Signals, Voice And Visual Displays
L
c NOTE Beep rate changes with different laser alerts.
14 English
Nothing comes close to a Cobra®
15
Detection
Your Detector
Your Detector
Instant-On Detection
Strobe Alert Signals, Voice And Visual Displays Type of Signal
Voice
Visual Display
3M Opticom or Tomar*
Emergency Vehicle Approaching
S Blinks
Your detector is designed to detect Instant-On speed monitoring signals, which can suddenly appear at full strength. NOTE You should take appropriate action immediately whenever an instant-on alert is given.
* Your detector provides 360˚ detection of this signal. Strobe Alert Signal Detected
X K Ka V S
Detection
c
Responding To Alerts Safety Alert Signals, Voice And Visual Displays Type of Signal
Voice
Visual Display
Emergency Vehicles
Emergency Vehicle Approaching
S is Steady
Road Hazards
Road Hazard Ahead
S is Steady
Trains
Train Approaching
S is Steady
Safety Alert Signal Detected
X K Ka V S
c
NOTE There are different tones for each Safety Alert. VG-2 And Spectre 1 Alert Signals, Voice And Visual Displays Type of Signal
Voice
Interceptor VG-2
VG-2 Alert
V is Steady
Spectre 1
Spectre Alert
V Blinks
VG-2 Alert Signal Detected
X K Ka V S
c
Visual Display
Spectre 1 Alert Signal Detected
X K Ka V S
c
NOTE There are different tones for each alert. 16 English
Description
Interpretation
Recommended Response
Tone repeats slowly at first, then speeds up rapidly.
Probably police radar
FULL ALERT
Tone sounds one (1) time only.
Probably a false alarm, but possibly pulsed radar, VG-2, or Spectre 1 nearby
Exercise caution
Tone instantly begins repeating rapidly.
Radar, VG-2, or Spectre 1 nearby has been activated suddenly
FULL ALERT
Tone repeats slowly as you Probably police approach a hill or bridge, radar beyond the then speeds up sharply as hill or bridge you reach it.
FULL ALERT
Tone repeats slowly for a short period.
Probably a false alarm
Exercise caution
Any type of laser alert.
Laser alerts are never false alarms
FULL ALERT
Any Safety Alert or Strobe Alert.
You are nearing an emergency vehicle, railroad crossing, or road hazard (construction, accident, etc.)
Exercise caution
Nothing comes close to a Cobra®
17
Your Detector
Understanding Radar And Laser
Understanding Radar And Laser Radar Speed Monitoring Systems
Your Detector
•
Three (3) band frequencies have been approved by the Federal Communications Commission (FCC) for use by speed monitoring radar equipment: X band
10.525 GHz
K band
24.150 GHz
Ka band
33.400 – 36.00 GHz
Your detector detects signals in all three (3) radar bands.
VG-2 And Spectre 1 VG-2 and Spectre 1 are “detector detectors” that work by detecting low-level signals emitted by most radar detectors. Your detector does not emit signals that can be detected by VG-2 or Spectre 1, but does detect VG-2 and Spectre 1 signals and will alert you when a device is in use near your vehicle, if you so choose.
Safety Alert Traffic Warning System FCC-approved Safety Alert transmitters emit microwave radar signals that indicate the presence of a safety-related concern. Depending on the frequency of the signal emitted, it can indicate a speeding emergency vehicle or train, or a stationary road hazard. Because these microwave signals are within the K band frequency, most conventional radar detectors will detect Safety Alert signals as standard K band radar. Your detector, however, is designed to differentiate between standard K band and Safety Alert signals, and give separate alerts for each. Safety Alert technology is relatively new. Safety Alert transmitters can be found in limited numbers in all 50 states, but the number is growing. Depending on your location, you may not receive these alerts regularly and may often encounter emergency vehicles, trains and road hazards without being alerted. As the number of transmitters increases, these alerts will become more common. When you receive such an alert, please watch for emergency vehicles ahead of you, on cross streets and behind you. If you see an emergency vehicle approaching, please pull over to the right side of the road and allow it to pass. 18 English
Understanding Radar And Laser
Strobe Alert Special strobes mounted on the light bars of authorized emergency vehicles (fire trucks, police cars, ambulances) automatically change traffic signals as the vehicle approaches an intersection. These strobes and the special strobe detectors located on the traffic signals, introduced fairly recently by 3M and Tomar, are already in use in more than 1000 cities nationwide. Cobra’s exclusive Strobe Alert detector will detect these special strobes and give an emergency vehicle alert. When you receive such an alert, please watch for an approaching emergency vehicle and pull over to allow it to pass. To inquire about coverage in your area, contact your local fire and police departments.
LIDAR (Laser) The correct name for the technology that most people refer to as laser is actually LIDAR, which stands for Light Detection and Ranging. LIDAR operates much like radar. Its signal spreads out like a radar signal, though not as widely. Unlike radar, LIDAR must have a clear line of sight to its target vehicle throughout the entire measurement interval. Obstructions such as sign posts, utility poles, tree branches, etc., will prevent valid speed measurement. Some common questions about LIDAR include: ■ Does weather have any affect on LIDAR? Yes. Rain, snow, smoke, fog, or airborne dust particles will reduce the effective range of LIDAR and can, if dense enough, prevent its operation. ■
Can LIDAR operate through glass? Yes. Newer LIDAR guns can obtain readings through most types of glass. However, the laser pulse also can be received through glass to trigger an alarm by your detector.
■
Can LIDAR operate while in motion? No. Because LIDAR operates by line of sight, the person using it cannot drive the vehicle, aim and operate the gun all at the same time.
■
Is LIDAR legal to use? Yes. It is legal in all 50 states.
Nothing comes close to a Cobra®
19
Your Detector
Maintenance
Maintenance Maintenance Of Your Radar Detector Your detector is designed and built to give you years of trouble-free performance without the need for service. No routine Maintenance is required. If your unit does not appear to be operating properly, please follow these troubleshooting steps: ■
Make sure the power cord is properly connected.
■
Make sure the socket of your vehicle’s cigarette lighter is clean and free of corrosion.
■
Make sure the power cord’s cigarette lighter adapter is firmly seated in your cigarette lighter.
■
Check the power cord fuse. (Unscrew the ribbed end cap of the cigarette lighter adapter and examine the fuse. If required, replace it with a 2-amp fuse only.)
Your Detector
•
Specifications
Specifications
•
Band And Frequencies Band
Frequencies
X Band
10.525
± 0.050
GHz
K Band
24.125
± 0.125
GHz
Safety Alert Traffic Warning System
24.070
± 0.010
GHz
24.110
± 0.010
GHz
24.190
± 0.010
GHz
24.230
± 0.010
GHz
Ka Band
34.700
± 1.300
GHz
Laser
910
± 50
nm
Strobe
700
± 300
nm
Unit Dimensions And Weight Dimensions* (H x W x D)
Weight*
11⁄3" x 23⁄4" x 41⁄3"
5.11 oz.
(34 mm x 70 mm x 110 mm)
(145 g)
* Dimensions and weight measurements are approximate.
This radar detector is covered by one or more of the following U.S. patents: 5,497,148; 5,594,432; 5,612,685; 6,078,279; 6,094,148. Additional patents may be listed inside the product or pending.
20 English
Nothing comes close to a Cobra®
21
Warranty
Warranty
Limited 1-Year Warranty For Products Purchased In The U.S.A. Cobra Electronics Corporation warrants that its Cobra 11 Band Radar/Laser Detectors, and the component parts thereof, will be free of defects in workmanship and materials for period of one (1) year from the date of first consumer purchase. This warranty may be enforced by the first consumer purchaser, provided that the product is utilized within the U.S.A. Cobra will, without charge, repair or replace, at its option, defective 11 Band Radar/Laser Detectors, products or component parts upon delivery to the Cobra Factory Service Department, accompanied by proof of the date of first consumer purchase, such as a duplicated copy of a sales receipt.
Customer Assistance
•
Product Service And Trademark Acknowledgement
Product Service If you have any questions about operation or installing your new Cobra product, or if you are missing parts…
•
Please call Cobra first! DO NOT RETURN THIS PRODUCT TO THE STORE! See customer assistance on page A1. If you suspect that your unit requires service, please call 773-889-3087 BEFORE shipping it to Cobra. This will ensure that you receive service as quickly as possible.
4. If the owner of the product resides outside the U.S.A.
If you are asked to send your unit to the Cobra factory, please follow these steps: 1) Send the complete unit, including power cord. (It is not necessary to include the mounting bracket.) 2) For warranty repair, enclose some form of proof-of-purchase, such as a photocopy or carbon copy of a sales receipt. If you send the original receipt, it cannot be returned. 3) Enclose a typed or clearly written description of the problem you are having with your unit, plus the name and address where you want the unit returned. 4) Pack the unit securely to prevent damage during transit. If possible, use the original packing materials. 5) Ship prepaid and insured using a traceable carrier such as United Parcel Service (UPS), Federal Express, or Priority mail with delivery confirmation. Ship to: Cobra Factory Service, Cobra Electronics Corporation, 6500 West Cortland Street, Chicago, IL 60707 U.S.A. 6) Please allow three (3) to four (4) weeks before contacting us about the status of your service. Call 773-889-3087 for assistance. If your unit is under warranty, it will either be repaired or replaced upon receipt, depending on the model. If your unit is out of warranty, you will receive a letter informing you of the repair or replacement charge.
All implied warranties, including warranties of merchantability and fitness for a particular purpose are limited in duration to the length of this warranty.
Trademark Acknowledgement
You must pay any initial shipping charges required to ship the product for warranty service, but the return charges will be at Cobra’s expense, if the product is repaired or replaced under warranty. This warranty gives you specific rights, and you may also have other rights which vary from state to state. Exclusions: This limited warranty does not apply: 1. To any product damaged by accident. 2. In the event of misuse or abuse of the product or as a result of unauthorized alterations or repairs. 3. If the serial number has been altered, defaced or removed.
Cobra shall not be liable for any incidental, consequential or other damages; including, without limitation, damages resulting from loss of use or cost of installation. Some states do not allow limitations on how long an implied warranty lasts and/or do not allow the exclusion or limitation of incidental or consequential damages, so the above limitations may not apply to you.
22 English
Cobra, 6 Band, DigiView, Extra Sensory Detection, HighGear, microTALK, LaserEye, Safety Alert Traffic Warning System, Strobe Alert, VG-2 Alert and Nothing comes close to a Cobra are registered trademarks of Cobra Electronics Corporation. Cobra Electronics Corporation, 11 Band, EasySet, IntelliMute, IntelliShield, Road Ready, SmartPower, Spectre Alert, UltraBright, Voice Alert and Xtreme Range Superheterodyne are trademarks of Cobra Electronics Corporation. Opticom is a trademark of 3M Corporation. Instaclear for Ford is a registered trademark of Ford Motor Company, Inc. Electriclear for GM is a registered trademark of General Motors Corporation. 20-20 and Ultra-Lyte are trademarks of Laser Technology, Inc. ProLaser and ProLaser III are trademarks of Kustom Signals, Inc. Bee III and Pop are a trademarks of MPH Industries. Spectre is a trademark of Stalcar. Interceptor VG-2 is a trademark of TechniSonic Industries LTD. Tomar is a registered trademark of TOMAR Electronics, Inc.
•
Nothing comes close to a Cobra®
23
Customer Assistance
Optional Accessories
Optional Accessories You can find quality Cobra products and accessories at your local Cobra dealer, or in the U.S.A., you can order directly from Cobra.
Customer Assistance
•
Order Form
Order Form
•
Name
Address (No P.O. Boxes)
City
State/Province
Zip
Country
Telephone
Credit Card Number
Type: ❒ Visa ❒ MasterCard ❒ Discover
Exp. Date
Customer Signature
Straight 12V DC Power Cord
Windshield Mounting Bracket
Includes plug and fuse Item # 420-030-N-001
Includes suction cups Item # 545-139-N-001
Item #
Description
420-030-N-001 420-026-N-001 545-139-N-001 CLP-2B
Straight 12V Power Cord Coiled 12V Power Cord Windshield Mounting Bracket Dual Port Power Adapter
U.S. Cost Each
Qty
Amount
U.S. Subtotal Amount Shipping/Handling* Tax Table Wisconsin add 5% $10.00 or less . . . . . $3.00 (Tax if Applicable) Indiana, Michigan, $10.01-$25.00 . . . . . $5.50 Ohio add 6% $25.01-$50.00 . . . . . $7.50 California add 7.25% Shipping/Handling Illinois add 8.75% $50.01-$90.00 . . . . $10.50 Total $90.01-$130.00 . . . $13.50 *For AK, HI and PR add additional $26.95 for FedEx Next Day or $10.95 for FedEx 2nd Day. Excludes weekends and holidays shipments. $130.01-$200.00 . . $16.50 Please allow two (2) to three (3) weeks for delivery in the U.S.A. $200.01 plus . . . . . 10% of purchase Prices subject to change without notice.
Ordering From U.S.A. Call 773-889-3087 for pricing or visit www.cobra.com. Coiled 12V DC Power Cord
Dual Port Power Adapter
Includes plug and fuse Item # 420-026-N-001
Includes adjustable plug (up to 90˚) and fuse Item # CLP-2B
24 English
For Credit Card Orders Complete and return this order form to fax number 773-622-2269. Or call 773-889-3087 [Press one (1) from the main menu] 8:00 a.m. to 6:00 p.m. CT, Monday through Friday. Make Check or Money Order Payable To Cobra Electronics, Attn: Accessories Dept., 6500 West Cortland Street, Chicago, IL 60707 U.S.A. To Order Online Please visit our website: www.cobra.com
Nothing comes close to a Cobra®
25
The Cobra line of quality products includes:
CB Radios microTALK® Radios Radar/Laser Detectors Safety Alert® Traffic Warning Systems Accessories GPS (Global Positioning System) HighGear® Accessories CobraMarine™ VHF Radios Power Inverters For more information or to order any of our products, please visit our website: www.cobra.com
Nothing comes close to a Cobra®
English
