Product Guide Spares Installation Guide Numerical Index

Transcript

Product Guide Duofix WC frames Page 3 Concealed cisterns Page 9 WC flush plates Page 14 Remote flushing kits Page 21 Duofix basin frames Page 27 Taps Page 28 Duofix bidet frames Page 42 Duofix urinal frames Page 43 Accessories Page 57 Drainage Page 62 Traps Page 67 Fill and flush valves for ceramic cisterns Page 77 Geberit AquaClean Page 79 Spares Page 97 Main methods of Duofix installation Page 111 Waste and drainage connection Page 117 Installation Guide Numerical Index Page 121 Product and Installation Guide Washroom & Bathroom 2011 1 Product Guide Compatibility - Flush plates and buttons Flush plates Sigma10 Sigma20 Rumba Sigma50 Tango Sigma60 UP320 UP720 ✓ ✓ ✓ ✓ 115.890.00.1 115.891.00.1 115.855.00.1 ✓ ✓ UP200 AP123 Mambo Samba Bolero HyTronic infra-red Large Access Cover Plate Kappa20 Kappa50 Artline Kappa21 ✓ Small Access Cover Plate ✓ HyTouch single flush buttons Short wall palm 115.114.xx.1 241.199.xx.1 Short wall finger 115.947.xx.1 .xx.1 Long wall finger 241.144.00.1 Long wall finger 115.943.21.1 Short wall palm 115.949.21.1 241.282.21.1 115.114.xx.1 115.947.xx.1 115.949.21.1 115.943.21.1 115.941.xx.1 115.114.xx.1 115.947.xx.1 115.949.21.1 115.943.21.1 115.941.xx.1 115.942.xx.1 115.075.21.x 115.942.xx.1 Palm push 115.941.xx.1 HyTouch dual flush buttons Hand push 115.942.xx.1 Finger push 115.999.21.1 Finger push 115.075.21.x HyTronic infra-red buttons Sensor flush 115.857.xx.1 Insert for in-cistern blocks 115.612.00.1 Insert for adding in-cistern blocks compatible with Geberit’s Sigma10, 20 and 50 range of flush plates 2 Product and Installation Guide Washroom & Bathroom 2011 241.199.xx.1 241.198.xx.1 241.282.21.1 241.144.00.1 115.941.xx.1 Product Guide Duofix WC frames Product Details Duofix WC frames Duofix WC frames Duofix WC frame 1.12 m with UP320 for Sigma flush plates - PreWall 12 50 R½ 100 112 1045 max. 62 41 23 25 °C Flush volume small range 3–4 l Flush volume factory setting 5.8 and 3 l Additional Note 2 Duofix PreWall brackets for system; Water supply connection R 1/2" with integrated angle stop valve and hand wheel; Conduit pipe for the water supply connection of Geberit AquaClean; Flush bend; Protection plug; Protection housing for service opening; 2 threaded rods M12 for ceramics fastening; WC connection set, ø 90 mm; WC outlet bend, HDPE, ø 90 mm; Adaptor sleeve, HDPE, ø 90/110 mm; Fastening material Excluded: Flush plate 0 0 0-20 48 73 Application 0.1–10 bar Operating temperature water max. 6 100 18/23 Flow pressure range 195 ≥ 30 Ordering Information Article no. PU1 PU4 111.383.00.5 1 12 9-135 • For installation of a wall-hung WC with bolt fixings set at 180 or 230 mm centres • For installation in a room-height Duofix system wall in front of a solid or drywall construction • For mounting in front of a solid or drywall construction • For a screed of 0 - 200 mm (not in room height applications) • For connecting Geberit AquaClean Characteristics • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Frame with holes ø 9 mm for fastening in wood frame construction • Sound-absorbing actuator rods, tool-free, fast adjustment • Concealed cistern fully insulated against condensation • Concealed cistern for tool-free mounting and maintenance • Frame height 1120 mm • With wall brackets to allow up to a 200 mm duct. For larger ducts up to 400 mm use extension bolts 111.887.00.1 • Tool-free fastening for outlet bend, sound-absorbing, adjustable in depth with 8 positions, adjustable range 45 mm • Connection hose to angle stop valve can be screwed without tools • Water supply connection at centre back or at the top • UP320 concealed cistern with front actuation • Dual flush with Sigma60, Sigma50, Sigma20, Samba or Bolero flush plates • Single flush with Sigma10, Rumba, Mambo or Tango flush plates • Dual flush with HyTouch pneumatic button • Single flush with HyTronic infra-red flush or HyTouch flush pneumatic buttons • The protection cover protects the service opening against moisture and dirt • Protection cover for service opening can be mounted without tools and cut to length • Universal water supply connection compatible with MeplaFix, can be mounted and operated without tools • Self-locking feet for tool-free alignment of the element. (Friction feet have to be locked with spanner) • For pans with contact surfaces smaller than 170 mm (see accessory 111.847.00.1) • Flush valve features settings to enable either a 6l and 3l flush or a 4.5l and 3l flush. For flush volumes of 4l and 2l a low flush beaker is required (241.894.00.1) Product and Installation Guide Washroom & Bathroom 2011 3 Product Guide Duofix WC frames Duofix WC frame 1.12 m with UP320 for Sigma flush plates 50 R½ 12 Product Details 6 100 100 112 1045 18/23 max. 62 41 23 0 0 0-20 Flow pressure range 0.1–10 bar Operating temperature water max. 25 °C Flush volume small range 3–4 l Flush volume factory setting 5.8 and 3 l Additional Note Water supply connection R 1/2" with integrated angle stop valve and hand wheel; Conduit pipe for the water supply connection of Geberit AquaClean; Flush bend; Protection plug; Protection housing for service opening; 2 threaded rods M12 for ceramics fastening; Fastening material Excluded: Flush plate; PreWall brackets; WC outlet bend, HDPE, ø 90 mm; Adaptor sleeve, HDPE, ø 90/110 mm Ordering Information 48 73 195 ≥ 30 9-135 Application Article no. PU1 PU4 111.384.00.5 1 12 • For installation of a wall-hung WC with bolt fixings set at 180 or 230 mm centres • For installation in a room-high Duofix system wall • For installation in a load bearing stud wall • For a screed of 0 - 200 mm (not in room height applications) • For connecting Geberit AquaClean Characteristics • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Frame with holes ø 9 mm for fastening in wood frame construction • Sound-absorbing actuator rods, tool-free, fast adjustment • Concealed cistern fully insulated against condensation • Concealed cistern for tool-free mounting and maintenance • Frame height 1120 mm • Tool-free fastening for outlet bend, sound-absorbing, adjustable in depth with 8 positions, adjustable range 45 mm • Connection hose to angle stop valve can be screwed without tools • Water supply connection at centre back or at the top • UP320 concealed cistern with front actuation • Dual flush with Sigma60, Sigma50, Sigma20, Samba or Bolero flush plates • Single flush with Sigma10, Rumba, Mambo or Tango flush plates • Dual flush with HyTouch pneumatic button • Single flush with HyTronic infra-red flush or HyTouch flush pneumatic buttons • The protection cover protects the service opening against moisture and dirt • Protection cover for service opening can be mounted without tools and cut to length • Cistern can be reversed to give access from behind in a duct situation when flushed with HyTouch pneumatic buttons or HyTronic sensor flush • Universal water supply connection compatible with MeplaFix, can be mounted and operated without tools • Self-locking feet for tool-free alignment of the element. (Friction feet have to be locked with spanner) • For pans with contact surfaces smaller than 170 mm (see accessory 111.847.00.1) • Flush valve features settings to enable either a 6l and 3l flush or a 4.5l and 3l flush. For flush volumes of 4l and 2l a low flush beaker is required (241.894.00.1) 4 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Duofix WC frames Duofix WC frame 0.82 m with UP200 for Kappa flush plates - PreWall Duofix WC frame 0.98 m with UP200 for Kappa flush plates - PreWall 50 min. 17 R1/2 915 min. 17 50 66 R1/2 755 max. 107 66 max. 91 75 91 18/23 98 18/23 82 max. 62 22 max. 62 41 23 40 32 0 33 0 0 0-20 0 0-20 73 195 73 195 ≥ 30 9-135 Application ≥ 30 48 • For installation of a wall-hung WC with bolt fixings set at 180 or 230 mm centres • For installation in a partial-height Duofix system wall in front of a solid or drywall construction • For mounting in front of a solid or drywall construction • For a screed of 0 - 200 mm 48 9-135 Application • For installation of a wall-hung WC with bolt fixings set at 180 or 230 mm centres • For installation in a partial-height Duofix system wall in front of a solid or drywall construction • For mounting in front of a solid or drywall construction • For a screed of 0 - 200 mm Characteristics Characteristics • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Frame with holes ø 9 mm for fastening in wood frame construction • Fast adjustment of the actuator rods for flush plate • Concealed cistern fully insulated against condensation • Protection housing for service opening, can be cut to length • Frame height 980 mm • With wall brackets to allow up to a 200 mm duct. For larger ducts up to 400 mm use extension bolts 111.887.00.1 • Concealed cistern UP200 with front or top actuation • Dual flush with flush plates Artline or Kappa flush plates • Dual flush with HyTouch pneumatic button • Single flush with HyTouch pneumatic and mechanical buttons • Water supply connection left • Fastening for outlet bend sound-absorbing • Connection hose to angle stop valve can be screw-connected by hand • For pans with contact surfaces smaller than 170 mm (see accessory 111.847.00.1) • To reduce flush volume to either 4.5/3 litre dual flush or 4/2.6 litre dual flush requires material number 242.310.00.1 (note: must be used with pans designed for low volume flush) • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Frame with holes ø 9 mm for fastening in wood frame construction • Fast adjustment of the actuator rods for flush plate • Concealed cistern fully insulated against condensation • Protection housing for service opening, can be cut to length • Frame height 820 mm • With wall brackets to allow up to a 200 mm duct. For larger ducts up to 400 mm use extension bolts 111.887.00.1 • Concealed cistern UP200 with front or top actuation • Dual flush with flush plates Artline or Kappa flush plates • Dual flush with HyTouch pneumatic button • Single flush with HyTouch pneumatic and mechanical buttons • Water supply connection left • Fastening for outlet bend sound-absorbing • Connection hose to angle stop valve can be screw-connected by hand • For pans with contact surfaces smaller than 170 mm (see accessory 111.847.00.1) • To reduce flush volume to either 4.5/3 litre dual flush or 4/2.6 litre dual flush requires material number 242.310.00.1 (note: must be used with pans designed for low volume flush) Product Details Product Details Flow pressure range Operating temperature water max. Flush volume factory setting 0.1–10 bar Flow pressure range 0.1–10 bar 25 °C Operating temperature water max. 25 °C 5.8 and 3 l Flush volume factory setting 5.8 and 3 l Additional Note 2 Duofix PreWall brackets for system; Water supply connection R 1/2" with integrated angle stop valve; Protection housing for service opening; 2 threaded rods M12 for ceramics fastening; WC connection set, ø 90 mm; WC outlet bend, HDPE, ø 90 mm; Adaptor sleeve, ø 90/ 110 mm; Protection plug; Fastening material Additional Note 2 Duofix PreWall brackets for system; Water supply connection R 1/2" with integrated angle stop valve; Protection housing for service opening; 2 threaded rods M12 for ceramics fastening; WC connection set, ø 90 mm; WC outlet bend, HDPE, ø 90 mm; Adaptor sleeve, ø 90/ 110 mm; Protection plug; Fastening material Excluded: Flush plate Excluded: Flush plate Ordering Information Ordering Information Article no. PU1 Article no. PU1 1 111.242.00.1 1 111.292.00.1 Product and Installation Guide Washroom & Bathroom 2011 5 Product Guide Duofix WC frames Duofix WC frame 1.12m with UP720 for Sigma flush plates - PreWall New 59 R½ 8 1-5 Product Details 98 100 18/23 112 98 ≤ 62 41 23 0 0 0-12 0-12 ≥ 34 have to be locked with spanner) • For pans with contact surfaces smaller than 170 mm (see accessory 111.847.00.1) • Element depth 8 cm 45 16 Flow pressure range 0.1–10 bar Operating temperature water max. 25 °C Flush volume factory setting 5.8 and 3 l Additional Note Water supply connection R 1/2" with integrated angle stop valve and hand wheel; Two protection plugs; Protection housing for service opening; Flush bend; 2 threaded rods M12 for ceramics fastening; WC connection set, ø 90 mm; WC outlet bend, PE-HD, ø 90 mm, extended; Adaptor sleeve, HDPE, ø 90/110 mm; Conduit pipe for the water supply connection of Geberit AquaClean; 2 PreWall brackets; Fastening material Excluded: Flush plate 135 Ordering Information Article no. PU1 PU4 111.729.00.1 1 12 0 0-12 Duofix WC frame 0.79 m with furniture concealed cistern - pneumatic 48 9 465 Application • For installation of a wall-hung WC with bolt fixings set at 180 or 230 mm centres • For installation in a room-height Duofix system wall in front of a solid or drywall construction • For installing in a load bearing stud wall • For installation in split-height PreWall construction in front of a solid or drywall construction • For installation in room-height PreWall or partition wall • For connecting Geberit AquaClean • Is not allowed to be embedded in concrete at full room height Characteristics • Self-supporting • Frame height 1120 mm • M12 fastening for ceramic appliances, fastening distance 18 cm or 23 cm • Geberit Sigma concealed cistern 8 cm (UP720), front actuation • Concealed cistern fully insulated against condensation • Protection cover for service opening can be mounted without tools and cut to length • Water supply connection at the top, offset to the left side • Universal water supply connection compatible with MeplaFix, can be mounted and operated without tools • Connection hose to angle stop valve can be screwed without tools • Sound-absorbing actuator rods, tool-free, fast adjustment • Single flush with Sigma10, Rumba, Mambo or Tango flush plates • Dual flush with Sigma60, Sigma50, Sigma20, Samba or Bolero flush plates • Adjustable flushing volume • Not suitable for use with flush buttons • The protection cover protects the service opening against moisture and dirt • Outlet bend depth with vertical connection 9 cm • Fastening for outlet bend adjustable in depth and sound-absorbing • Installation depth at least 8 cm with vertical drainage connection • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet galvanised, adjustable 0-12 cm • Self-locking feet for tool-free alignment of the element. (Friction feet 6 195−315 79 18/23 0 0 0-20 10 195 Application • For installation of a wall-hung WC with bolt fixings set at 180 or 230 mm centres • For installation in bathroom furniture with full length front panel (not for use with front plinths) • For furniture with an internal dimension of 465 mm wide, the item can not be used with side plinths • For dual flush Characteristics • Pneumatic flush actuation • Front or top actuation • Water supply connection at the bottom left • Self-supporting • Powder-coated frame, ultramarine blue • Galvanised leg supports, steplessly adjustable 0 - 200 mm Product Details Flow pressure range 0.1–10 bar Operating temperature water max. 25 °C Flush volume factory setting 5.5 and 3 l Additional Note Dual flush actuator Ordering Information Article no. PU1 111.706.00.1 1 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Duofix WC frames Duofix WC corner frame 1.12 m with UP320 for Sigma flush plates 500-760 R½ 128 60 1000 1000 Additional Note Water supply connection R 1/2" with integrated angle stop valve and hand wheel; Flush bend; Conduit pipe for the water supply connection of Geberit AquaClean; Protection plug; Installation kit for electrical connection; Protection housing for service opening; 2 threaded rods M12 for ceramics fastening; WC outlet pipe, HDPE, ø 90 mm; Adaptor sleeve, HDPE, ø 90/110 mm; WC connection set, ø 90 mm; Fastening material Excluded: Flush plate 1120 180/230 1045 max. 620 410 20 10 230 Ordering Information Article no. PU1 PU4 111.399.00.5 1 10 0 0 0-200 90 48 110 Application • For installation of a wall-hung WC with bolt fixings set at 180 or 230 mm centres • For installation as a corner element in front of a drywall, solid wall, Duofix system wall • For a screed of 0 - 200 mm (not in room height applications) • For connecting Geberit AquaClean Characteristics • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Frame with axis centre mark • Sound-absorbing actuator rods, tool-free, fast adjustment • Concealed cistern fully insulated against condensation • Concealed cistern for tool-free mounting and maintenance • Frame height 1120 mm • Connection hose to angle stop valve can be screwed without tools • Water supply connection at centre back or at the top • UP320 concealed cistern with front actuation • Dual flush with Sigma60, Sigma50, Sigma20, Samba or Bolero flush plates • Single flush with Sigma10, Rumba, Mambo or Tango flush plates • Dual flush with dual flush HyTouch pneumatic and mechanical buttons • Not suitable for use with flush buttons • The protection cover protects the service opening against moisture and dirt • Protection cover for service opening can be mounted without tools and cut to length • Universal water supply connection compatible with MeplaFix, can be mounted and operated without tools • Telescopic profiles to fasten to the wall and for fastening panelling • Telescopic profiles with detent mark • Wall fixture variable from 30° to 60° • Narrow leg supports allow for lateral offset of the drainage pipe • Support for front, top and lateral panelling • Variable element depth (see page 116) • For pans with contact surfaces smaller than 170 mm (see accessory 111.847.00.1) • Flush valve features settings to enable either a 6l and 3l flush or a 4.5l and 3l flush. For flush volumes of 4l and 2l a low flush beaker is required (241.894.00.1) Product Details Flow pressure range 0.1–10 bar Operating temperature water max. 25 °C Flush volume small range 3–4 l Flush volume factory setting 6 and 3 l Product and Installation Guide Washroom & Bathroom 2011 7 Product Guide Duofix WC frames Duofix WC frame 1.12 m with UP320 for Disabled WC and Sigma flush plates 425 R½ 170 45 1000-1010 1000 1120 180/230 410-460 1045-1055 230-280 20 10 130 0 0 30 Product Details Flow pressure range 0.1–10 bar Operating temperature water max. 25 °C Flush volume small range 3–4 l Flush volume factory setting 5.8 and 3 l Additional Note Water supply connection R 1/2" with integrated angle stop valve and hand wheel; Conduit pipe for the water supply connection of Geberit AquaClean; Flush bend; Protection plug; Protection housing for service opening; WC connection set, ø 90 mm; WC outlet bend, HDPE, ø 90 mm; Adaptor sleeve, HDPE, ø 90/110 mm; 2 threaded rods M12 for ceramics fastening; Fastening material Excluded: Flush plate 0-200 48 73 300 300 90-135 Ordering Information Article no. PU1 PU4 111.352.00.5 1 8 Application • For installation of a wall-hung WC with bolt fixings set at 180 or 230 mm centres • For wall-hung WC with projection > 620 mm • For installation in a partial-height Duofix system wall in front of a solid or drywall construction • For installation in a room-high Duofix system wall • For installation in a load bearing stud wall • For mounting in front of a solid or drywall construction (order PreWall brackets 111.844.00.1 separately) • For installation in split-height PreWall construction in front of a solid or drywall construction • For a screed of 0 - 200 mm (not in room height applications) • For disabled WC installations • For connecting Geberit AquaClean Duofix frame for support handles 100 85 112 50 0 0 Characteristics • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Frame with holes ø 9 mm for fastening in wood frame construction • Sound-absorbing actuator rods, tool-free, fast adjustment • Concealed cistern fully insulated against condensation • Concealed cistern for tool-free mounting and maintenance • Frame height 1120 mm • Tool-free fastening for outlet bend, sound-absorbing, adjustable in depth with 8 positions, adjustable range 45 mm • Connection hose to angle stop valve can be screwed without tools • Water supply connection at centre back or at the top • UP320 concealed cistern with front actuation • Dual flush with Sigma60, Sigma50, Sigma20, Samba or Bolero flush plates • Single flush with Sigma10, Rumba, Mambo or Tango flush plates • The protection cover protects the service opening against moisture and dirt • Not suitable for use with flush buttons • Protection cover for service opening can be mounted without tools and cut to length • Universal water supply connection compatible with MeplaFix, can be mounted and operated without tools • Self-locking feet for tool-free alignment of the element. (Friction feet have to be locked with spanner) • For pans with contact surfaces smaller than 170 mm (see accessory 111.847.00.1) • Adjustable installation height of the WC, 410 - 460 mm • Flush valve features settings to enable either a 6l and 3l flush or a 4.5l and 3l flush. For flush volumes of 4l and 2l a low flush beaker is required (241.894.00.1) 8 4 365 0-20 48 73 Application • For installation of grab rails • For a screed of 0 - 200 mm • For installation in a room-height Duofix system wall in front of a solid or drywall construction • For installation in a room-high Duofix system wall • For mounting in front of a solid or drywall construction (order PreWall brackets 111.844.00.1 separately) • For installation in a load bearing stud work Characteristics • Frame height 1120 mm • Frame with holes ø 9 mm for fastening in wood frame construction • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Fastening plate for support handles made from veneer wood, waterresistant laminate, adjustable height and depth • Self-locking feet for tool-free alignment of the element. (Friction feet have to be locked with spanner) Additional Note Fastening material Ordering Information Article no. PU1 PU4 111.790.00.1 1 10 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Concealed cisterns Sound insulation Concealed cisterns Concealed cisterns Concealed dual flush cistern UP320 for Sigma flush plates 57 16-205 41 12 R1/2 2-9 100 100 235 845 Application 51 • For wall-hung WC and wall-hung bidet • For sanitaryware with fixing centres 180 mm or 230 mm • For decoupling solid-borne noise with WC and bidet • Insulation to be trimmed after pan fixed 108 1045 365 23 135 Characteristics 0 0 • White 30 Product Details Product material PE expanded Application Material thickness 6 mm • For concealed installation • For back to wall floor-standing WCs Additional Note 2 acoustic insulation sleeves Characteristics Ordering Information Article no. PU1 PU2 PU4 156.050.00.1 1 10 200 • Concealed cistern fully insulated against condensation • Front actuation only • Protection cover for service opening can be mounted without tools and cut to length • Dual flush with Sigma60, Sigma50, Sigma20, Samba or Bolero flush plates • Dual flush with dual flush HyTouch pneumatic and mechanical buttons • Single flush with Sigma10, Rumba, Mambo or Tango flush plates • Single flush with HyTronic infra-red flush or HyTouch pneumatic buttons • Flushing unit for dual flush and single flush • Adjustable flushing volume • Water supply connection at centre back or at the top • Flush bend has maximum 8 cm adjustment. Flush can be cut down by maximum of 8 cm • Installation height 1080 mm (can be cut down, depending on the WC pan performance) • Installation depth adjustable, 160 - 205 mm • Fastening bracket adjustable in depth • Cistern can be reversed to give access from behind in a duct situation when flushed with HyTouch pneumatic buttons or HyTronic sensor flush • Flush valve features 6l and 4.5l flush settings to enable either a 6l and 3l flush or a 4.5l and 3l flush. For flush volumes of 4l and 2l a low flush beaker is required (241.894.00.1) Product Details Flow pressure range 0.1–10 bar Operating temperature water max. 25 °C Flush volume small range 3–4 l Flush volume factory setting 5.8 and 3 l Additional Note Water supply connection R 1/2" with integrated angle stop valve; Protection housing for service opening; Flush pipe ø 45 mm; Fastening for flush bend; Protection plug for flush pipe; 2 slotted flat irons; 2 fastening brackets, pre-mounted; Fastening material Excluded: Flush plate Ordering Information Article no. PU1 PU4 109.309.00.5 1 20 Product and Installation Guide Washroom & Bathroom 2011 9 Product Guide Concealed cisterns Concealed dual flush cistern UP720 for Sigma flush plates 8 505 Concealed dual flush cistern UP200 for Kappa flush plates 57 1–5 18 min.3 465 8 R1/2 87 87 110 25 9 110 max.9 13 465 335 57 max.9 65–80 X -15 0 -15 X 0 Application 0 0 • For concealed installation • For back to wall floor-standing WCs ≥ 30 Application Characteristics • For solid construction • For floor standing WC • For concealed installation • Front or top actuation • Installation depth adjustable 18 cm - 24.5 cm • Fully insulated against condensation • Water supply connection left • Dual flush with flush plates Artline or Kappa flush plates • Dual flush with dual flush HyTouch pneumatic and mechanical buttons • Single flush with HyTouch single flush pneumatic buttons • Connection hose to angle stop valve can be screw-connected by hand • Flush bend, welded • Fast adjustment of the actuator rods for flush plate • Cistern height 82 cm • To reduce flush volume to either 4.5/3 litre dual flush or 4/2.6 litre dual flush requires material number 242.310.00.1 (note: must be used with pans designed for low volume flush) Characteristics • Concealed cistern fully insulated against condensation • Geberit Sigma concealed cistern 8 cm (UP720), front actuation • Concealed cistern for simple installation and tool-free repair works • Protection cover for service opening can be mounted without tools and cut to length • Universal water supply connection compatible with MeplaFix, can be mounted and operated without tools • Connection hose to angle stop valve can be screwed without tools • Dual flush with Sigma60, Sigma50, Sigma20, Samba or Bolero flush plates • Stop-and-go flush with Rumba, Mambo or Tango actuator plate • Single flush with Sigma10 actuator plate • Flush bend has maximum 8 cm adjustment. Flush can be cut down by maximum of 8 cm • Adjustable flushing volume • Water supply connection at the top, offset to the left side • Flush bend adjustable, 2 cm upwards and 1 cm downwards 0.1–10 bar Operating temperature water max. 25 °C Flush volume factory setting 9 and 3 l Flush volume large range 6/9l Flush volume small 3l Flow pressure range 0.1–10 bar Operating temperature water max. 25 °C Flush volume small range 3–4 l Flush volume factory setting 5.8 and 3 l Additional Note Water supply connection R 1/2" with integrated angle stop valve; Protection housing for service opening; Protection plug for flush bend; Fastening for flush bend; 2 fastening brackets, pre-mounted; Fastening material Product Details Flow pressure range Product Details Excluded: Flush plate Ordering Information Additional Note Water supply connection R 1/2" with integrated angle stop valve and hand wheel; Flush bend; Protection housing for service opening; Fastening material; Protection plug for flush bend Article no. PU1 PU4 109.200.00.1 1 27 Excluded: Flush plate Ordering Information Article no. PU1 PU4 109.772.00.1 1 32 10 Price £ 145.00 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Concealed cisterns Concealed dual flush cistern UP200 for Kappa flush plates with extended flush pipe New 57 Concealed single flush cistern AP123 128 41 18 33 min.3 465 45 25 9 65 max.9 13 38 38 595 465 max.9 305–3 65 X Application 0 0 Application • For concealed installation • For back to wall floor-standing WCs Characteristics • For floor-standing and wall-hung WCs • For private and semi-public areas • For concealed installation Characteristics • Front or top actuation • Installation depth adjustable 18 cm - 24.5 cm • Protection housing for service opening, can be cut to length • Fully insulated against condensation • Water supply connection left • Dual flush with flush plates Artline or Kappa flush plates • Dual flush with dual flush HyTouch pneumatic and mechanical buttons • Single flush with HyTouch single flush pneumatic buttons • Connection hose to angle stop valve can be screw-connected by hand • Flush bend, welded • Connection hose to angle stop valve can be screw-connected by hand • Fast adjustment of the actuator rods for flush plate • Cistern height 98 cm • To reduce flush volume to either 4.5/3 litre dual flush or 4/2.6 litre dual flush requires material number 242.310.00.1 (note: must be used with pans designed for low volume flush) Product Details Flow pressure range 0.1–10 bar Operating temperature water max. 25 °C Flush volume small range 3–4 l Flush volume factory setting 5.8 and 3 l • Fully insulated against condensation • Impuls380 side filling valve • Cover without button • Water supply connection left and right • Flush pipe connection fitted • Single flush with HyTouch single flush pneumatic buttons • 300 mm extention pipe available (118.131.11.1) Product Details Fill time (6 l) at 3 bar flow pressure 30 s Fill time (9 l) at 3 bar flow pressure 45 s Flush volume range 6/9l Drainage capacity 2.2–2.9 l/s Flush volume factory setting 9l Additional Note Flush bend 39 x 35 cm, ø 50/44 mm; Pneumatic actuation unit; Fastening material Excluded: Angle stop valve R 1/2"; Pneumatic push button Ordering Information Article no. Colour PU1 PU4 123.137.11.1 White 1 24 Additional Note Water supply connection R 1/2" with integrated angle stop valve; Protection housing for service opening; Protection plug for flush bend; WC connection set, ø 90 mm; 2 fastening brackets, pre-mounted; Fastening material Excluded: Flush plate Ordering Information Article no. PU1 109.211.00.1 1 Product and Installation Guide Washroom & Bathroom 2011 11 Product Guide Concealed cisterns Pneumatic operated concealed dual flush cistern for low height furniture 464 30 132 98 Monolith for wall mounted WC, glass 8 106 485 R½ 908 9 M64x2 94 8 355 47 75-16 R1/2 45 65 15 4 13 13 4 43 101 25 29 0 18/23 0 Application • For installation in low height bathroom furniture (minimum height 790 mm from finished floor) • For back to wall floor-standing WCs 4 Application • Pneumatic flush actuation • Water supply connection at the bottom left • Top or front access • Includes dual flush pneumatic button • For wall mounted WC with 240 - 260 mm wall drainage outlet (for further drainage outlet options please see accessories on page 66) • For use in wall outlet connections, outlet height in excess of 230 mm • For mounting on finished floors • Requires Monolith feet if installing onto a low weight bearing or dry wall installation (131.104.00.1) - see page 60 • For installation as part of renovation work, design or new build • Not suitable for Geberit AquaClean - see page 13 Product Details Characteristics Characteristics Flow pressure range 0.1–10 bar Operating temperature water max. 25 °C Flush volume factory setting 5.5 and 3 l Additional Note Dual flush actuator; Flush bend; Sleeve; Fastening material Ordering Information Article no. PU1 PU4 109.720.00.1 1 24 • Includes a Duofix frame PreWall mounted • Self-supporting • Compensation of dimensional tolerances • Height compensation up to 20 mm • Dual flush • Adjustable flushing volume • Fully insulated against condensation • Water supply connection at the bottom left or right • Front panel made of 8 mm glass • Brushed and anodised aluminium side profiles • Side base pods can be adjusted to skirting board Product Details Flow pressure range 0.1–10 bar Operating temperature water max. 25 °C Flush volume factory setting 6 and 3 l Flush volume large range 4.5 / 6 l Additional Note Cistern element with front and side cladding; Water supply connection set with angle stop valve; Flush pipe 230 x 230 mm, ø 50 / 44 mm; WC outlet pipe, HDPE, ø 90 mm; Adaptor sleeve, HDPE, ø 90/110 mm; 2 threaded rods M12 for ceramics fastening; Fastening material for solid wall; Fastening material for wall-hung WC Ordering Information Article no. Colour PU1 PU4 131.021.SI.1 White glass / aluminium 1 6 131.021.SJ.1 Black glass / aluminium 1 6 1 6 131.021.SK.1 12 NEW Mint glass / white aluminium Product and Installation Guide Washroom & Bathroom 2011 Product Guide Concealed cisterns Monolith for Geberit AquaClean Monolith for floor mounted WC, glass 106 485 R½ 908 R½ 908 106 485 25 101 18/23 1010 10 25 455 180 28 0 10 15 0 0 0 Application Application • For close coupled WC with 150 mm floor drainage outlet (for further drainage outlet options please see accessories on page 66) • For use in floor outlet connections • For use in wall outlet connections, outlet height 180 mm (requires 131.083.16.1) • For mounting on finished floors • For installation as part of renovation work, design or new build • For wall mounted WC with 240 - 260 mm wall drainage outlet (for further drainage outlet options please see accessories on page 66) • For use in wall outlet connections, outlet height in excess of 230 mm • For mounting on finished floors • Requires Monolith feet if installing onto a low weight bearing or dry wall installation (131.104.00.1) - see page 60 • For installation as part of renovation work, design or new build • For connecting Geberit AquaClean WC Characteristics Characteristics • Includes a Duofix frame PreWall mounted • Self-supporting • Compensation of dimensional tolerances • Height compensation up to 20 mm • Integrated dual flush • Adjustable flushing volume • Fully insulated against condensation • Water supply connection at the bottom left or right • Front panel made of 8 mm glass • Brushed and anodised aluminium side profiles • Side base pods can be adjusted to skirting board • Includes a Duofix frame PreWall mounted • Self-supporting • Compensation of dimensional tolerances • Height compensation up to 20 mm • Dual flush • Adjustable flushing volume • Fully insulated against condensation • Water supply connection at the bottom left or right • Front panel made of 8 mm glass • Brushed and anodised aluminium side profiles • Side base pods can be adjusted to skirting board Product Details Product Details Flow pressure range 0.1–10 bar Flow pressure range 0.1–10 bar Operating temperature water max. 25 °C Operating temperature water max. 25 °C Flush volume factory setting 6 and 3 l Flush volume factory setting 6 and 3 l Flush volume large range 4.5 / 6 l Flush volume large range 4.5 / 6 l Additional Note Cistern element with front and side cladding; Water supply connection set with angle stop valve; Flush pipe 230 x 230 mm, ø 50 / 44 mm; Pbend, PP, ø 90 mm ; Adaptor sleeve, HDPE, ø 90/110 mm; Fastening material for solid wall; Rubber seal EPDM Ordering Information Ordering Information Article no. Colour PU1 PU4 131.002.SI.1 White glass / aluminium 1 6 Black glass / aluminium 1 6 1 6 131.002.SJ.1 131.002.SK.1 Additional Note Cistern element with front and side cladding; Water supply connection set with angle stop valve; Flush pipe 230 x 230 mm, ø 50 / 44 mm; WC outlet pipe, HDPE, ø 90 mm; Adaptor sleeve, HDPE, ø 90/110 mm; 2 threaded rods M12 for ceramics fastening; Acoustic insulation set; Fastening material for solid wall; Fastening material for wall-hung WC NEW Mint glass / white aluminium Article no. Colour PU1 PU4 131.023.SI.1 White glass / aluminium 1 6 131.023.SJ.1 Black glass / aluminium 1 6 Product and Installation Guide Washroom & Bathroom 2011 13 Product Guide WC flush plates Sigma50 dual flush plate for UP320 and UP720 Bespoke cover WC flush plates WC flush plates Sigma10 single flush plate for UP320 and UP720 14 246 246 11 164 164 Application • For Geberit concealed cistern UP300, UP320 and UP720 • For dual flush • For customer to install a bespoke finish with max. of 3 mm depth • Not suitable for UP200, Twinline and Artline cisterns Application • For Geberit concealed cistern UP300, UP320 and UP720 • For single flush • Not suitable for UP200, Twinline and Artline cisterns Product Details Product Details Actuation force < 20 N Actuation force < 20 N Product material Die-cast zinc Product material Plastic Additional Note Mounting frame; Distance bolts; Actuator rods Additional Note Mounting frame; Push rod; Distance bolts Excluded: Design cover Ordering Information Ordering Information Article no. PU1 PU2 Article no. Colour PU1 PU2 PU4 115.788.00.1 1 5 115.758.KJ.1 White / gloss chrome / white 1 10 180 115.758.KK.1 White / gold-plated / white 1 10 180 White / matt chrome / matt chrome 1 10 180 1 10 180 Gloss chrome / matt chrome / 115.758.KH.1 1 gloss chrome 10 180 10 180 115.758.KL.1 115.758.KM.1 Black / gloss chrome / black 115.758.KN.1 Matt chrome / gloss chrome / matt chrome 1 Sigma50 dual flush plate for UP320 and UP720 Glass cover 246 14 164 Sigma20 dual flush plate for UP320 and UP720 11 246 164 Application • For Geberit concealed cistern UP300, UP320 and UP720 • For dual flush • Not suitable for UP200, Twinline and Artline cisterns Product Details Application Actuation force < 20 N • For Geberit concealed cistern UP300, UP320 and UP720 • For dual flush • Not suitable for UP200, Twinline and Artline cisterns Product material Die-cast zinc / glass Additional Note Mounting frame; Distance bolts; Actuator rods Product Details Actuation force < 20 N Ordering Information Product material Plastic Article no. Colour PU1 PU2 Additional Note Mounting frame; Distance bolts; Actuator rods 115.788.SC.1 White with ornament x 1 5 115.788.SE.1 1 5 Ordering Information 115.788.SD.1 Smoked glass reflective 1 5 Article no. Colour PU1 PU2 PU4 115.778.KJ.1 White / gloss chrome / white 1 10 180 1 10 180 White / matt chrome / matt chrome 1 10 180 1 10 180 Gloss chrome / matt chrome / gloss 115.778.KH.1 1 chrome 10 180 Matt chrome / gloss chrome / matt 1 chrome 10 180 115.778.KK.1 White / gold-plated / white 115.778.KL.1 115.778.KM.1 Black / gloss chrome / black 115.778.KN.1 14 Green satinised Product and Installation Guide Washroom & Bathroom 2011 Product Guide WC flush plates Sigma50 dual flush plate for UP320 and UP720, Anti Vandal - Brushed stainless steel Sigma50 dual flush plate for UP320 and UP720 Plastic cover 14 246 14 246 164 164 Application Application • For Geberit concealed cistern UP300, UP320 and UP720 • For dual flush • Not suitable for UP200, Twinline and Artline cisterns • For installation in vandal resistant systems • For Geberit concealed cistern UP300, UP320 and UP720 • For dual flush • Not suitable for UP200, Twinline and Artline cisterns Product Details Characteristics • Can be locked with screws Actuation force < 20 N Product material Die-cast zinc / plastic Additional Note Mounting frame; Distance bolts; Actuator rods Actuation force < 20 N Product material Brass / chrome-plated die-cast zinc Additional Note Mounting frame; Distance bolts; Actuator rods; Fastening material Ordering Information Article no. Product Details PU1 PU2 115.788.DW.1 Black RAL 9005 Colour 1 5 Ordering Information 115.788.11.1 White 1 5 Article no. 115.788.EP.1 Pergamon 1 5 115.785.GH.1 Brushed stainless steel Colour PU2 1 5 Sigma50 dual flush plate for UP320 and UP720, Anti Vandal - Bespoke cover Sigma50 dual flush plate for UP320 and UP720 Brushed stainless steel 246 14 246 PU1 14 164 164 Application Application • For dual flush • For Geberit concealed cistern UP300, UP320 and UP720 • For front actuation • For use with Geberit Sigma concealed cistern 8 cm (UP720 and UP700) • Not suitable for UP200, Twinline and Artline cisterns • For Geberit concealed cistern UP300, UP320 and UP720 • For dual flush • For installation in vandal resistant systems • For customer to install a bespoke finish with max. of 3 mm depth • Not suitable for UP200, Twinline and Artline cisterns Characteristics • Can be locked with screws Product Details Actuation force < 20 N Product Details Product material Brass / chrome-plated die-cast zinc Actuation force < 20 N Additional Note Mounting frame; Distance bolts; Actuator rods; Fastening material Additional Note Mounting frame; Distance bolts; Actuator rods; Fastening material Ordering Information Ordering Information Article no. Colour 115.788.GH.1 Brushed stainless steel PU1 PU2 Article no. PU1 PU2 1 5 115.785.00.1 1 5 Product and Installation Guide Washroom & Bathroom 2011 15 Product Guide WC flush plates Sigma50 dual flush plate for UP320 and UP720, Anti Vandal - Glass cover Sigma60 dual flush plate for UP320 and UP720, Brushed chrome New 14 246 18−6 221 164 06−18 139 Application • For Geberit concealed cistern UP300, UP320 and UP720 • For dual flush • Not suitable for UP200, Twinline and Artline cisterns Application • For dual flush • For Geberit concealed cistern UP320 and UP720 • For front actuation • For use with plaster boarding/panelling 18 - 60 mm • Not suitable for use with UP300 and UP700 concealed cisterns Characteristics • Can be locked with screws Product Details Characteristics Actuation force < 20 N Product material Die-cast zinc / glass • Surface even actuation • For use with tiles 6–18 mm • Sound-absorbing actuator rods, tool-free, fast adjustment Additional Note Mounting frame; Distance bolts; Actuator rods; Fastening material Product Details Product material Die-cast zinc Ordering Information PU1 PU2 Ordering Information 115.785.SC.1 White with ornament x 1 5 Article no. 115.785.SD.1 Smoked glass reflective 1 5 115.792.GH.1 1 115.785.SE.1 1 5 Article no. Colour Green glass satinised Sigma50 dual flush plate for UP320 and UP720, Anti Vandal - Plastic cover PU1 Sigma60 cover frame, Brushed chrome New 06 15 14 246 164 164 246 Application Application • For use with Geberit Sigma60 flush plate • For Geberit concealed cistern UP300, UP320 and UP720 • For dual flush • For Geberit concealed cistern UP300 • Not suitable for UP200, Twinline and Artline cisterns Product Details Product material Die-cast zinc Characteristics • Can be locked with screws Ordering Information Product Details Article no. Actuation force < 20 N 242.544.GH.1 1 PU1 Product material Die-cast zinc / plastic Additional Note Mounting frame; Distance bolts; Actuator rods; Fastening material Ordering Information Article no. Colour PU1 PU2 115.785.11.1 White alpine 1 5 115.785.DW.1 Black RAL 9005 1 5 115.785.EP.1 1 5 16 Pergamon Product and Installation Guide Washroom & Bathroom 2011 Product Guide WC flush plates Insert for in-cistern blocks for Sigma10, 20 and 50 flush plates for UP320 Bolero dual flush plate for UP320 and UP720 14 246 1-95 164 Application Application • For Geberit concealed cistern UP300 and UP320 • For front actuation • For adding in-cistern blocks without chlorine or oxidising components • Not suitable for UP720, UP200, Twinline and Artline cisterns • Not suitable for use with the following flush plates: Sigma60, Samba, Bolero, Rumba, Tango, Mambo, Twist Additional Note Cover; Receptacle for in-cistern blocks; Mounting frame with swivelling mechanism • For Geberit concealed cistern UP300, UP320 and UP720 • For dual flush • Not suitable for UP200, Twinline and Artline cisterns Product Details Actuation force < 20 N Product material Plastic Additional Note Push rods; Distance rods; Fastening material Ordering Information Ordering Information Article no. PU1 PU2 115.612.00.1 1 5 Samba dual flush plate for UP320 and UP720 246 15 164 Article no. Colour PU1 PU2 PU4 115.777.10.1 Bahama beige 1 10 115.777.11.1 White 1 10 180 115.777.21.1 Gloss chrome 1 10 180 115.777.46.1 Matt chrome 1 10 180 115.777.CG.1 Manhattan 1 10 115.777.DK.1 Edelweiss 1 10 115.777.DT.1 1 10 115.777.DW.1 Black RAL 9005 1 10 115.777.EP.1 Pergamon 1 10 115.777.FB.1 Agais 1 10 115.777.FR.1 Star white 1 10 1 10 115.777.KB.1 Gloss chrome / structured chrome 1 10 Fine brass 115.777.GM.1 Satinox Application 180 180 • For Geberit concealed cistern UP300, UP320 and UP720 • For dual flush • Not suitable for UP200, Twinline and Artline cisterns Product Details Actuation force < 20 N Product material Plastic Additional Note Push rods; Distance rods; Fastening material Ordering Information Article no. Colour PU1 PU2 PU4 115.770.10.1 Bahama beige 1 10 180 115.770.11.1 White 1 10 180 115.770.21.1 Gloss chrome 1 10 180 115.770.46.1 Matt chrome 1 10 180 115.770.CG.1 Manhattan 1 10 180 115.770.DK.1 Edelweiss 1 10 180 115.770.DT.1 1 10 115.770.DW.1 Black RAL 9005 1 10 180 115.770.EP.1 Pergamon 1 10 180 115.770.FB.1 Agais 1 10 115.770.FR.1 Star white 1 10 180 1 10 180 115.770.KB.1 Gloss chrome / structured chrome 1 10 180 Fine brass 115.770.GM.1 Satinox Product and Installation Guide Washroom & Bathroom 2011 17 Product Guide WC flush plates Tango single flush plate for UP320 and UP720, Anti Vandal 246 Mambo single flush plate for UP320 and UP720, Anti Vandal 25 246 1 164 164 Application • For Geberit concealed cistern UP300, UP320 and UP720 • For single flush • Not suitable for UP200, Twinline and Artline cisterns Application • For Geberit concealed cistern UP300, UP320 and UP720 • For single flush • Not suitable for UP200, Twinline and Artline cisterns Characteristics Characteristics • Can be locked with anti-vandal screws • Can be locked with anti-vandal screws Product Details Product Details Actuation force < 20 N Actuation force < 20 N Product material Die-cast zinc Product material Stainless steel Additional Note Push rod; Distance rods; Fastening material Additional Note Push rod; Distance rods; Fastening material Ordering Information Ordering Information Article no. Colour PU1 PU2 PU4 Article no. PU1 PU2 PU4 115.760.11.1 White 1 10 180 115.751.00.1 1 10 180 115.760.21.1 Gloss chrome 1 10 180 115.760.45.1 Gold-plated 1 10 115.760.46.1 Matt chrome 1 10 115.760.DT.1 Fine brass 1 10 115.760.GM.1 Satinox 1 10 115.760.HC.1 Palladium 1 10 1 10 115.760.KA.1 Gloss chrome / matt chrome 180 Artline dual flush plate for UP200 213 16 142 Application Rumba single flush plate for UP320 and UP720 246 15 164 • For Geberit concealed cisterns UP200 and Artline • For top or front actuation • For dual flush • Not suitable for UP720, UP300, UP320 and Twinline cisterns Product Details Actuation force < 20 N Application Product material Plastic • For Geberit concealed cistern UP300, UP320 and UP720 • For single flush • Not suitable for UP200, Twinline and Artline cisterns Additional Note Push rods; Distance rods; Fastening material Product Details Ordering Information Actuation force < 20 N Article no. Colour PU1 PU2 PU4 Product material Plastic 115.666.11.1 White 1 10 200 115.666.21.1 Gloss chrome 1 10 200 115.666.46.1 Matt chrome 1 10 200 Additional Note Push rod; Distance rods; Fastening material Ordering Information Article no. Colour PU1 PU2 PU4 115.750.11.1 White 1 10 180 115.750.21.1 Gloss chrome 1 10 180 115.750.46.1 Matt chrome 1 10 180 1 10 Gloss chrome / structured 115.750.KB.1 chrome 18 Product and Installation Guide Washroom & Bathroom 2011 Product Guide WC flush plates Kappa50 dual flush plate for UP200 Kappa20 dual flush plate for UP200 213 211 16 142 15 142 Application Application • For Geberit concealed cisterns UP200 and Artline • For top or front actuation • For dual flush • Not suitable for UP720, UP300, UP320 and Twinline cisterns • For Geberit concealed cisterns UP200 and Artline • For top or front actuation • For dual flush • Not suitable for UP720, UP300, UP320 and Twinline cisterns Product Details Actuation force < 20 N Product material Plastic Product Details Additional Note Push rods; Distance rods; Fastening material Actuation force < 20 N Product material Die-cast zinc Additional Note Push rods; Distance rods; Fastening material Ordering Information Article no. Colour PU1 PU2 PU4 115.228.10.1 Bahama beige 1 Ordering Information 10 Article no. Colour PU1 PU2 PU4 White 1 10 180 115.228.11.1 White 1 10 200 115.260.11.1 115.228.21.1 Gloss chrome 1 10 200 115.260.21.1 Gloss chrome 1 10 180 200 115.260.46.1 Matt chrome 1 10 180 1 10 1 10 115.228.46.1 Matt chrome 1 10 115.228.CG.1 Manhattan 1 10 115.260.HC.1 Palladium 115.228.DK.1 Edelweiss 1 10 115.258.00.1 115.228.DT.1 1 10 115.228.DW.1 Black RAL 9005 Fine brass 1 10 115.228.EP.1 Pergamon 1 10 115.228.FB.1 Agais 1 10 115.228.FR.1 Star white 1 10 115.228.GM.1 Satinox 1 10 115.228.KB.1 Gloss chrome / structured chrome 1 10 200 Stainless steel Small access/cover plate for UP200 213 142 Kappa21 dual flush plate for UP200 212 14 Application • For Geberit concealed cisterns UP200 and Artline • Not suitable for UP720, UP300, UP320 and Twinline cisterns 142 Application • For Geberit concealed cistern UP200 • For top or front actuation • For dual flush • Not suitable for UP720, UP300, UP320 and Twinline cisterns Product Details Actuation force < 20 N Product material Plastic Additional Note Mounting frame; Actuator rods; Distance bolts; Fastening material Product Details Product material Plastic Additional Note Distance rods; Fastening material Ordering Information Article no. Colour PU1 115.680.11.1 White 1 115.680.21.1 Gloss chrome 1 Ordering Information Article no. Colour 115.240.KJ.1 White / gloss chrome / white 115.240.KH.1 Gloss chrome / matt chrome / gloss chrome 115.240.KM.1 Black / gloss chrome / black 115.240.KK.1 White / gold-plated / white 115.240.KL.1 White / matt chrome / matt chrome 115.240.KN.1 Matt chrome / gloss chrome / matt chrome Product and Installation Guide Washroom & Bathroom 2011 19 Product Guide WC flush plates Extension set for flush plates Large access/cover plate for UP320 and UP720 246 164 Application Application • For Geberit concealed cistern UP300, UP320 and UP720 • Not suitable for UP200, Twinline and Artline cisterns • For Geberit concealed cistern UP300, UP320 and UP720 • For extending flush plates up to an outer wall of max. 180 mm • For Sigma10, Sigma20, Sigma50, Rumba, Samba, Bolero, Tango, Twist, Mambo and Kappa flush plates • For Artline flush plates with UP200 cistern • Not suitable for Artline plates with Artline cistern Characteristics • Can be locked with anti-vandal screws Product Details Product material Die-cast zinc Additional Note Distance rods; Fastening material Additional Note 2 extensions for push rods; 2 extensions for distance rods; Fastening material Ordering Information Ordering Information Article no. Colour PU1 PU2 PU4 115.765.46.1 Matt chrome 1 10 180 Article no. PU1 PU2 240.938.00.1 1 10 Large access/cover plate for UP320 and UP720 246 164 Application • For Geberit concealed cistern UP300, UP320 and UP720 • Not suitable for UP200, Twinline and Artline cisterns Characteristics • Can be locked with anti-vandal screws Product Details Product material Stainless steel Additional Note Distance rods; Fastening material Ordering Information Article no. PU1 PU2 PU4 115.798.00.1 1 10 180 20 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Remote flushing kits HyTouch pneumatic short wall finger push button metal with actuator Remote flushing kits Remote flushing kits HyTouch pneumatic short wall palm push button plastic with actuator 0 - 30 17-25 63 6 122 52 Application 62 43 Application • For pneumatic remote flush actuation of Geberit concealed cisterns UP200, UP300, UP320, Artline and Twinline • For single flush • For wall thicknesses of 17 - 25 mm • Not suitable for UP720, AP123 or low height cisterns Characteristics • For pneumatic remote flush actuation of Geberit concealed cisterns UP200, UP300, UP320, Artline and Twinline • For single flush • For wall thicknesses of 0 - 30 mm • 50 mm hole required • Not suitable for UP720, AP123 or low height cisterns Product Details Actuation force < 25 N Additional Note Pneumatic flush button with bellows; Pneumatic actuation unit; 2 m air hose • Round design • 53 mm hole required Product Details Ordering Information Actuation force < 25 N Article no. Additional Note Pneumatic flush button with bellows; Pneumatic actuation unit; 2 m air hose Colour 115.947.00.1 115.947.21.1 Gloss chrome PU1 PU3 1 12 1 12 PU4 360 Ordering Information Article no. Colour PU1 PU2 PU4 115.114.11.1 White 1 10 240 115.114.21.1 Gloss chrome 1 10 240 HyTouch pneumatic short wall finger push button metal without actuator 0 - 30 HyTouch pneumatic short wall palm push button plastic without actuator 122 17-25 Application 6 52 63 62 43 Application • For pneumatic remote flush actuation of Geberit concealed cistern AP123 • For single flush • For wall thicknesses of 17 - 25 mm • Not suitable for UP200, UP720, UP300, UP320, Artline and Twinline cisterns Characteristics • For pneumatic remote flush actuation of Geberit concealed cistern AP123 • For single flush • For wall thicknesses of 0 - 30 mm • 50 mm hole required • Not suitable for UP200, UP720, UP300, UP320, Artline and Twinline cisterns Product Details Actuation force < 25 N Additional Note Pneumatic flush button with bellows Ordering Information • Round design • 53 mm hole required Product Details Actuation force Article no. Colour PU1 PU3 241.198.21.1 Gloss chrome 1 12 241.198.00.1 < 25 N 1 Additional Note Pneumatic flush button with bellows Ordering Information Article no. Colour PU1 PU2 PU3 241.199.11.1 White 1 10 100 241.199.21.1 Gloss chrome 1 10 100 Product and Installation Guide Washroom & Bathroom 2011 21 Product Guide Remote flushing kits HyTouch pneumatic short wall palm push button metal with actuator HyTouch pneumatic long wall push button metal single flush 0 - 30 0 - 170 63 63 264 122 Application Application • For pneumatic remote flush actuation of Geberit concealed cisterns UP200, UP300, UP320, Artline and Twinline • For single flush • For wall thicknesses of 0 - 30 mm • 50 mm hole required • Not suitable for UP720, AP123 or low height cisterns • For pneumatic remote flush actuation of Geberit concealed cistern AP123 • For single flush • For wall thicknesses of 0 - 170 mm • Not suitable for UP200, UP720, UP300, UP320, Artline and Twinline cisterns Product Details Product Details Actuation force Actuation force < 25 N Additional Note Pneumatic flush button with bellows; Pneumatic actuation unit; 2 m air hose < 25 N Additional Note Pneumatic flush button with bellows and sleve Ordering Information Ordering Information Article no. Colour PU1 PU3 115.949.21.1 Gloss chrome 1 12 Article no. PU1 PU2 241.144.00.1 1 8 HyTouch pneumatic long wall push button metal single flush HyTouch pneumatic short wall palm push button metal without actuator 6-27 0 - 30 63 37 Application 122 Application • For pneumatic remote flush actuation of Geberit concealed cistern AP123 • For single flush • For wall thicknesses of 0 - 30 mm • Not suitable for UP200, UP720, UP300, UP320, Artline and Twinline cisterns Product Details • For pneumatic remote flush actuation of Geberit concealed cisterns AP123, UP200, UP300, UP320, Artline and Twinline • For single flush • For wall thicknesses of 60 - 270 mm • Not suitable for UP720 Characteristics • Round design • 45 mm hole required Product Details Actuation force < 25 N Additional Note Pneumatic flush button with bellows Actuation force < 25 N Additional Note Pneumatic actuation unit; 2 m air hose Ordering Information Article no. Colour PU1 Ordering Information 241.282.21.1 Gloss chrome 1 Article no. Colour PU1 PU2 PU4 115.943.21.1 Gloss chrome 1 10 120 22 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Remote flushing kits HyTouch pneumatic hand push button - single flush HyTouch pneumatic finger push button - dual flush 108 8 9 8 M64x2 108 min. 15- max. 18 Application • For pneumatic remote single flush actuation of Geberit concealed cisterns UP200, UP300, UP320, AP123, Artline and Twinline • For single flush • Not suitable for UP720 Characteristics • Square design Product Details Application • For pneumatic remote flush actuation of Geberit concealed cisterns UP200, UP300, UP320, Artline and Twinline • For dual flush • 65 mm hole required • Not suitable for UP720 and AP123 Characteristics Actuation force < 25 N • Round design Additional Note Conduit pipe, 1.7 m; 2 m air hose; Concealed housing; Pneumatic actuator; Protection housing; Fastening material Product Details Ordering Information Additional Note Pneumatic actuation unit; 2 m air hose Article no. Colour PU1 PU2 PU4 115.941.11.1 White 1 10 120 115.941.KA.1 Gloss chrome / matt chrome 1 10 120 Actuation force < 25 N Ordering Information Article no. Colour PU1 PU2 PU4 115.999.21.1 Gloss chrome 1 10 240 HyTouch pneumatic hand push button - dual flush HyTouch mechanical finger push button dual flush, plastic 108 New ø 45 Ø 65 108 035 85 Application • For pneumatic remote flush actuation of Geberit concealed cisterns UP200, UP300, UP320, Artline and Twinline • For dual flush • Not suitable for UP720, AP123 or low height cisterns 52 13 Application • For drywall construction • For Geberit concealed cistern UP200 • For dual flush • Not suitable for UP300, UP320, UP720, Twinline, AP123 or furniture cisterns Characteristics • Square design Product Details Actuation force < 25 N Characteristics Additional Note Conduit pipe, 1.7 m; 2 m air hose; Concealed housing; Pneumatic actuator; Protection housing; Fastening material Ordering Information Article no. Colour PU1 PU2 PU4 115.942.11.1 White 1 10 120 115.942.KA.1 Gloss chrome / matt chrome 1 10 120 • Flush actuation using cable actuator • Actuator made of plastic • Fastening for actuator on the back with counter nut • Length of the cable actuator cannot be changed • 45 mm hole required Product Details Product material Plastic Additional Note Dual flush actuator with cable actuators; Lifter for installation on flush valve; Protective pipe; Counter nut with extension; Fastening material Ordering Information Article no. PU1 PU2 115.075.21.1 1 10 Product and Installation Guide Washroom & Bathroom 2011 23 Product Guide Remote flushing kits HyTouch mechanical finger push button dual flush, metal New HyTouch pneumatic foot operated flush - floor mounted 12 ø 45 Ø 65 33 035 85 12 52 Application 13 Application • For drywall construction • For Geberit concealed cistern UP200 • For dual flush • Not suitable for UP300, UP320, UP720, Twinline, AP123 or furniture cisterns Characteristics • Flush actuation using cable actuator • Actuator made of die-cast zinc • Fastening for actuator on the back with counter nut • Length of the cable actuator cannot be changed • 45 mm hole required Product Details Actuation force Product Details Product material • For pneumatic remote single flush actuation of Geberit concealed cisterns UP200, UP300, UP320, AP123, low height cistern, Artline and Twinline • For single flush • For solid construction • For installation in floor • For drywall construction • For pneumatic remote control flush actuation of Geberit surfacemounted and concealed cisterns • Not suitable for UP720 Die-cast zinc Additional Note Dual flush actuator with cable actuators; Lifter for installation on flush valve; Protective pipe; Counter nut with extension; Fastening material < 25 N Additional Note Conduit pipe, 3 m; Pneumatic hose, 3.5 m; Pneumatic actuation unit; Protection box made of EPS; Fastening material Ordering Information Article no. PU1 PU2 PU4 115.939.00.1 1 10 120 Ordering Information Article no. PU1 PU2 115.075.21.Z 1 10 HyTouch pneumatic foot operated flush - wall mounted 154 11 Application • For pneumatic remote single flush actuation of Geberit concealed cisterns UP200, UP300, UP320, AP123, low height cistern, Artline and Twinline • For single flush • For installation in floor • Not suitable for UP720 Product Details Actuation force < 25 N Additional Note Conduit pipe, 3 m; Pneumatic hose, 3.5 m; Pneumatic actuation unit; Fastening material Ordering Information Article no. PU1 PU2 PU4 115.918.00.1 1 10 120 24 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Remote flushing kits HyTronic automatic infra-red WC flush for UP720, mains power New HyTronic automatic infra-red WC flush for UP320, mains power Application • For use with UP720 concealed cistern • For use with the Mambo IRBA flush plate • Not suitable for barrier-free and wheelchair-suitable construction • Not suitable for UP300, UP320, UP200, Artline, Twinline, AP123 or low height furniture cisterns Characteristics • Infra-red user detection • Self-calibrating infra-red control • Infra-red detection with background fade-out • Driven by servo motor • Operation with extra-low voltage – no mains voltage in the cistern • Self-calibrating electrical lifting device • Low-noise lifting mechanism • Automatic flush release • Manual, touchless flush release • Manual flush actuation using flush plate • Triggers a full flush • Minimum detection time can be set • Initial flush can be set • Repeat flush can be set • Flush actuator made of stainless steel, can be connected with antivandal screws • Flush actuation can be deactivated using HyTronic Clean Handy • Flush actuation settings can be made and checked, using HyTronic Service Handy • Plug connection with cross-polarity protection • Easy maintenance and cleaning • Easy installation and servicing • Requires transformer 115.861.00.1 Product Details Application • For use with Geberit UP300 and UP320 concealed cistern • For use with the Mambo IRBA flush plate • Not suitable for barrier-free and wheelchair-suitable construction • Not suitable for UP200, UP720 Artline, Twinline, AP123 or low height furniture cisterns Characteristics • Infra-red user detection • Self-calibrating infra-red control • Infra-red detection with background fade-out • Driven by servo motor • Operation with extra-low voltage – no mains voltage in the cistern • Self-calibrating electrical lifting device • Low-noise lifting mechanism • Automatic flush release • Manual, touchless flush release • Manual flush actuation using flush plate • Triggers a full flush • Minimum detection time can be set • Initial flush can be set • Repeat flush can be set • Flush actuator made of stainless steel, can be connected with antivandal screws • Flush actuation can be deactivated using HyTronic Clean Handy • Flush actuation settings can be made and checked, using HyTronic Service Handy • Plug connection with cross-polarity protection • Easy maintenance and cleaning • Easy installation and servicing • Requires transformer 115.861.00.1 Interval flush adjustment range 1–168 h Interval flush factory setting 24 h Activation time 7s Product Details Activation time range 1–60 s Interval flush adjustment range 1–168 h Operating voltage 4.1 V DC Interval flush factory setting 24 h Nominal voltage 230 V AC Activation time 7s Mains frequency 50 Hz Activation time range 1–60 s Protection degree IP 45 Operating voltage 4.1 V DC Nominal voltage 230 V AC Mains frequency 50 Hz Protection degree IP 45 Additional Note Actuator plate Mambo IRBA with infra-red window, stainless steel; Mounting frame with infra-red control, pre-mounted; Cradle with servo motor and lifting device, pre-mounted; Push rod; Distance rods; Fastening material Ordering Information Additional Note Actuator plate Mambo IRBA with infra-red window, stainless steel; Mounting frame with infra-red control, pre-mounted; Cradle with servo motor and lifting device, pre-mounted; Cover; Push rod; Distance rods; Fastening material Article no. PU1 Excluded: Power supply unit 115.855.00.1 1 Excluded: Power supply unit Ordering Information Article no. PU1 115.890.00.1 1 Product and Installation Guide Washroom & Bathroom 2011 25 Product Guide Remote flushing kits HyTronic automatic infra-red WC flush for UP320, battery powered HyTronic infra-red sensor flush 43 33 NA4V1_V 20.6.02 0008 0.1 0 - 30 Application • For use with Geberit UP300 and UP320 concealed cistern • For use with the Mambo IRBA flush plate • Not suitable for barrier-free and wheelchair-suitable construction • Not suitable for UP200, UP720 Artline, Twinline, AP123 or low height furniture cisterns Application • For automatic flush actuator of UP300 and UP320 concealed cistern • For single flush • Not suitable for UP200, UP720, Twinline, AP123, low height cisterns and Artline cisterns Characteristics Product Details • Infra-red user detection • Self-calibrating infra-red control • Infra-red detection with background fade-out • Driven by servo motor • Operation with extra-low voltage – no mains voltage in the cistern • Self-calibrating electrical lifting device • Low-noise lifting mechanism • Automatic flush release • Manual, touchless flush release • Manual flush actuation using flush plate • Triggers a full flush • Minimum detection time can be set • Initial flush can be set • Repeat flush can be set • Flush actuator made of stainless steel, can be connected with antivandal screws • Flush actuation can be deactivated using HyTronic Clean Handy • Flush actuation settings can be made and checked, using HyTronic Service Handy • Plug connection with cross-polarity protection • Easy maintenance and cleaning • Easy installation and servicing Product material Stainless steel Nominal voltage 230 V AC Operating voltage 4.1 V DC Additional Note Power supply unit; Installation phase box for power supply unit; Electrical lifting device for flush valve with control electronics Ordering Information Article no. Colour PU1 115.857.00.1 Stainless steel 1 115.857.21.1 Gloss chrome 1 Product Details Interval flush adjustment range 1–168 h Interval flush factory setting 24 h Activation time 7s Activation time range 1–60 s Operating voltage 3 V DC Battery type LR20 Additional Note Actuator plate Mambo IRBA with infra-red window, stainless steel; Mounting frame with infra-red control and battery compartment, premounted; Cradle with servo motor and lifting device, pre-mounted; 2 batteries, each 1.5 V LR20 alkaline; Cover; Push rod; Distance rods; Fastening material Ordering Information Article no. PU1 115.891.00.1 1 26 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Duofix basin frames Duofix basin frame 0.82 / 0.98 m Duofix basin frames Duofix basin frames 6 50 Duofix basin frame 1.12 m 5-38 85 6 50 100 85 5-38 7 80 76 112 7 80 76 153 0 153 0 52 0-20 0-20 48 Application • For installation of a wall-hung washbasin with bolt fixings set at between 50 and 380 mm centres (with accessories 111.868.00.1 fastening distance can extend from 380 - 580 mm) • For installation in a room-high Duofix system wall • For installation in a load bearing stud wall • For a screed of 0 - 200 mm Characteristics • Frame height 1120 mm • Frame with holes ø 9 mm for fastening in wood frame construction • Washbasin fastening distance 50 - 380 mm • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Tap connection plate with adjustable height and depth • Fastening for outlet bend, adjustable height • With wall brackets to allow up to a 200 mm duct. For larger ducts up to 400 mm use extension bolts 111.887.00.1 • With backplate elbows and chrome isolating valves with 3/8" BSP connection Additional Note 2 water connections R 1/2"; 2 angle stop valves R 1/2"; 2 Duofix PreWall brackets for system; 2 threaded rods M10 for ceramics fastening; Fastening material Article no. PU1 111.495.00.1 1 0 48 73 Application 73 Ordering Information 52 306 306 0 98 (82) • For installation in a partial-height Duofix system wall in front of a solid or drywall construction • For installation of a wall-hung washbasin with bolt fixings set at between 50 and 380 mm centres (with accessories 111.868.00.1 fastening distance can extend from 38 - 58 cm) • For a screed of 0 - 200 mm Characteristics • Frame height 820 / 980 mm • Frame with holes ø 9 mm for fastening in wood frame construction • Washbasin fastening distance 50 - 380 mm • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Tap connection plate with adjustable height and depth • Fastening for outlet bend, adjustable height • With wall brackets to allow up to a 200 mm duct. For larger ducts up to 400 mm use extension bolts 111.887.00.1 • With backplate elbows and chrome isolating valves with 3/8" BSP connection Additional Note 2 water connections R 1/2"; 2 angle stop valves R 1/2"; 2 Duofix PreWall brackets for system; 2 threaded rods M10 for ceramics fastening; Fastening material Ordering Information Article no. PU1 111.494.00.1 1 Product and Installation Guide Washroom & Bathroom 2011 27 Product Guide Taps Duofix basin frame 1.12 - 1.3 m for wall mounted taps 50 Taps Taps HyTronic60 infra-red sensor tap without mixer, mains powered 11 5-38 85 122 112-130 193 80 56 135 35 52 0 0 0-20 05-3 36 73 SW36 48 Application • For installation of a wall-hung washbasin with bolt fixings set at between 50 and 380 mm centres (with accessories 111.868.00.1 fastening distance can extend from 380 - 580 mm) • For installation in a room-high Duofix system wall • For installation in a load bearing stud wall • For a screed of 0 - 200 mm • For washbasin with concealed wall-mounted tap • Disc for mounting the concealed wall-mounted tap Characteristics • Frame height 1120 mm to 1300 mm • Frame with holes ø 9 mm for fastening in wood frame construction • Washbasin fastening distance 50 - 380 mm • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Fastening for outlet bend, adjustable height • Fastening plate for concealed fittings, veneered wood, waterproof bonded, adjustable in height and depth • Self-locking feet for tool-free alignment of the element. (Friction feet have to be locked with spanner) Additional Note Outlet bend ø 50 mm; Seal ø 44/32 mm; 2 threaded rods M10 for ceramics fastening; Fastening material Ordering Information Article no. PU1 PU4 111.493.00.1 1 10 G 3/8 Application • For cold or mixed water connection • For installation in washbasin or work top Characteristics • Electrical power supply via power supply unit • Volume flow control with aerator • Automatic triggering • Self-calibrating infra-red control • Vandal-proof • Requires transformer 241.692.00.1 Product Details Max. operating temperature mixed water 45 °C Maximum operating temperature, short-term 90 °C Product material Chrome-plated brass Activation distance factory setting 22 cm Activation distance adjustment range 5–22 cm Operating pressure 1–8 bar Ambient temperature 1–40 °C Flow rate at 3 bar 6 l/min Nominal voltage 230 V AC Mains frequency 50 Hz Operating voltage 9 V DC Additional Note Connection cable 1.7 m for power supply unit; Metal-reinforced hose R 3/8"; Filter; Fastening material Excluded: Power supply unit Sound dampening set for washbasin 60 SW19 22 05 20 Ordering Information Article no. Colour PU1 PU4 115.740.21.1 Gloss chrome 1 62 Application • For solid-borne noise insulation with washbasins Product Details Product material PE expanded Additional Note 2 acoustic insulation sleeves Ordering Information Article no. PU1 156.051.00.1 1 28 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Taps HyTronic60 infra-red sensor tap without mixer, battery powered HyTronic60 infra-red sensor tap with mixing lever, mains powered 122 193 122 193 56 56 135 35 05-3 36 135 35 05-3 36 SW36 SW36 SW19 SW19 22 22 G 3/8 G 3/8 Application Application • For cold or mixed water connection • For installation in washbasin or work top • For cold and hot water connection • For installation in washbasin or work top Characteristics Characteristics • Electrical power supply via power supply unit • Volume flow control with aerator • Automatic triggering • Self-calibrating infra-red control • Vandal-proof • Requires transformer 241.692.00.1 • Electrical power supply via power supply unit • Volume flow control with aerator • Automatic triggering • Self-calibrating infra-red control • Vandal-proof • Requires transformer 241.692.00.1 Product Details Product Details 45 °C Differentiated pressure CW/WW ≤ 1.5 bar Maximum operating temperature, short-term 90 °C Operating temperature water max. 65 °C Product material Chrome-plated brass Maximum operating temperature, short-term 90 °C Activation distance factory setting 22 cm Product material Chrome-plated brass Activation distance adjustment range 5–22 cm Activation distance factory setting 22 cm 1–8 bar Activation distance adjustment range 5–22 cm Ambient temperature 1–40 °C Operating pressure 1–8 bar Flow rate at 3 bar 6 l/min Ambient temperature 1–40 °C 6 V DC Flow rate at 3 bar 6 l/min CR - P2 (6 V) Nominal voltage 230 V AC Max. operating temperature mixed water Operating pressure Operating voltage Battery type Additional Note 6 V battery; Metal-reinforced hose R 3/8"; Filter; Fastening material Mains frequency 50 Hz Operating voltage 9 V DC Article no. Colour PU1 PU4 Additional Note Connection cable 1.7 m for power supply unit; 2 metal-reinforced hoses R 3/8"; 2 non-return valves 3/8"; 2 filters; Fastening material 115.733.21.1 Gloss chrome 1 62 Excluded: Power supply unit Ordering Information Ordering Information Article no. Colour PU1 PU4 115.738.21.1 Gloss chrome 1 62 Product and Installation Guide Washroom & Bathroom 2011 29 Product Guide Taps HyTronic60 infra-red sensor tap with mixing lever, battery powered HyTronic60 infra-red sensor tap with internal mixing, mains powered 122 193 122 193 56 56 135 35 05-3 36 135 35 05-3 36 SW36 SW36 SW19 SW19 22 22 G 3/8 G 3/8 Application Application • For cold and hot water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top • For cold and hot water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top Characteristics Characteristics • Power supply by battery • Temperature adjustment via the mixer lever • Volume flow control with aerator • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Electrical power supply via power supply unit • Temperature pre-setting via the internal mixer • Volume flow control with aerator • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Requires transformer 241.692.00.1 Product Details Differentiated pressure CW/WW ≤ 1.5 bar Product Details Operating temperature water max. 65 °C Differentiated pressure CW/WW ≤ 1.5 bar Maximum operating temperature, short-term 90 °C Operating temperature water max. 65 °C Product material Chrome-plated brass Maximum operating temperature, short-term 90 °C Activation distance factory setting 22 cm Product material Chrome-plated brass Activation distance adjustment range 5–22 cm Activation distance factory setting 22 cm Operating pressure 1–8 bar Activation distance adjustment range 5–22 cm Ambient temperature 1–40 °C Operating pressure 1–8 bar Flow rate at 3 bar 6 l/min Ambient temperature 1–40 °C Operating voltage 6 V DC Flow rate at 3 bar 6 l/min Battery type CR - P2 (6 V) Nominal voltage 230 V AC Mains frequency 50 Hz Operating voltage 9 V DC Additional Note 6 V battery; 2 metal-reinforced hoses R 3/8"; 2 non-return valves 3/8"; 2 filters; Fastening material; Key for aerator Ordering Information Article no. Colour PU1 PU4 115.723.21.1 Gloss chrome 1 62 Additional Note Connection cable 1.7 m for power supply unit; 2 metal-reinforced hoses R 3/8"; 2 non-return valves 3/8"; 2 filters; Fastening material Excluded: Power supply unit Ordering Information 30 Article no. Colour PU1 PU4 115.739.21.1 Gloss chrome 1 62 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Taps HyTronic60 infra-red sensor tap with internal mixing, battery powered Transformer for HyTronic60 tap 55 122 55 193 56 135 35 Application • For concealed installation • For parallel connection of up to six Geberit washbasin taps with infrared control 05-3 36 SW36 Product Details SW19 Nominal voltage 22 G 3/8 Application • For cold and hot water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top 230 V AC Mains frequency 50 Hz Output voltage 9 V DC Ordering Information Article no. PU1 241.692.00.1 1 Characteristics • Power supply by battery • Temperature pre-setting via the internal mixer • Volume flow control with aerator • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Vandal-proof • Setting and interrogation option with HyTronic Service Handy Product Details Differentiated pressure CW/WW ≤ 1.5 bar Operating temperature water max. 65 °C Maximum operating temperature, short-term 90 °C Product material Chrome-plated brass Activation distance factory setting 22 cm Activation distance adjustment range 5–22 cm Operating pressure 1–8 bar Ambient temperature 1–40 °C Flow rate at 3 bar 6 l/min Operating voltage 6 V DC Battery type CR - P2 (6 V) Additional Note 6 V battery; 2 metal-reinforced hoses R 3/8"; 2 non-return valves 3/8"; 2 filters; Fastening material; Key for aerator Ordering Information Article no. Colour PU1 PU4 115.725.21.1 Gloss chrome 1 62 Product and Installation Guide Washroom & Bathroom 2011 31 Product Guide Taps HyTronic185 infra-red sensor tap without mixer, mains powered HyTronic185 infra-red sensor tap without mixer, battery powered 115 115 Ø 64 Ø 64 16 25° Ø 27-38 14 16 125 25° Ø 27-38 14 02-38 448 125 02-38 448 3/8" 3/8" Application Application • For cold or mixed water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top • For cold or mixed water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top Characteristics Characteristics • Temperature is not adjustable • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Can be changed from mains operation to battery operation • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Volume flow control with aerator • Various functions can be set manually • Watersaver program adjustable • Interval flush program adjustable • Integrated check valve • Electrical power supply via power supply unit • Requires transformer 241.672.00.1 • Temperature is not adjustable • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Volume flow control with aerator • Various functions can be set manually • Watersaver program adjustable • Interval flush program adjustable • Integrated check valve • Power supply by battery • Battery is sufficient to activate the water flow 200000 times • Warning if the battery is low • Energy saving mode can be set Product Details Product Details Product material Chrome-plated brass Activation distance factory setting 16–18 cm Product material 1–33 cm Activation distance factory setting 16–18 cm Ambient temperature 1–40 °C Activation distance adjustment range 1–33 cm Operating pressure 0.5–8 bar Ambient temperature 1–40 °C 90 °C Operating pressure 0.5–8 bar Flow rate at 3 bar 6 l/min Maximum operating temperature, short-term 90 °C Mains frequency 50 Hz Flow rate at 3 bar 6 l/min 230 V AC Operating voltage 6 V DC Operating voltage 12 V AC Battery type CR - P2 (6 V) Max. operating temperature mixed water 45 °C Max. operating temperature mixed water 45 °C Activation distance adjustment range Maximum operating temperature, short-term Nominal voltage Chrome-plated brass Additional Note Metal-reinforced hose R 3/8"; Filter; Key for aerator; 1.5 m connection cable; Power supply unit; Fastening material Additional Note Metal-reinforced hose R 3/8"; Filter; 6 V battery; Key for aerator; Fastening material Ordering Information Ordering Information Article no. 116.135.21.1 32 Colour Gloss chrome PU1 1 PU4 Article no. Colour PU1 PU4 81 116.235.21.1 Gloss chrome 1 81 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Taps HyTronic185 infra-red sensor tap with mixing lever, mains powered HyTronic185 infra-red sensor tap with mixing lever, battery powered 115 115 Ø 64 Ø 64 16 25° Ø 27-38 16 125 25° Ø 27-38 14 125 02-38 14 448 02-38 448 3/8" 3/8" Application • For cold and hot water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top Application • For cold and hot water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top Characteristics • Temperature adjustment via the mixer lever • Unmixed hot or cold water cannot be adjusted • Proportion of hot water can be limited • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Can be changed from mains operation to battery operation • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Volume flow control with aerator • Various functions can be set manually • Watersaver program adjustable • Interval flush program adjustable • Integrated check valve • Electrical power supply via power supply unit • Requires transformer 241.672.00.1 Product Details Characteristics • Temperature adjustment via the mixer lever • Unmixed hot or cold water cannot be adjusted • Proportion of hot water can be limited • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Volume flow control with aerator • Various functions can be set manually • Watersaver program adjustable • Interval flush program adjustable • Integrated check valve • Power supply by battery • Battery is sufficient to activate the water flow 200000 times • Warning if the battery is low • Energy saving mode can be set Differentiated pressure CW/WW ≤ 1.5 bar Product material Chrome-plated brass Product Details Activation distance factory setting 16–18 cm Differentiated pressure CW/WW ≤ 1.5 bar Activation distance adjustment range 1–33 cm Product material Chrome-plated brass Ambient temperature 1–40 °C Activation distance factory setting 16–18 cm Operating pressure 0.5–8 bar Activation distance adjustment range 1–33 cm Maximum operating temperature, short-term 90 °C Ambient temperature 1–40 °C Flow rate at 3 bar 6 l/min Operating pressure 0.5–8 bar Mains frequency 50 Hz Maximum operating temperature, short-term 90 °C Nominal voltage 230 V AC Flow rate at 3 bar 6 l/min Operating voltage 12 V AC Operating voltage 6 V DC Operating temperature water max. 65 °C Battery type CR - P2 (6 V) Operating temperature water max. 65 °C Additional Note 2 metal-reinforced hoses R 3/8"; 2 filters; Key for aerator; 1.5 m connection cable; Power supply unit; Fastening material Ordering Information Article no. Colour PU1 PU4 116.155.21.1 Gloss chrome 1 81 Additional Note 2 metal-reinforced hoses R 3/8"; 2 filters; 6 V battery; Key for aerator; Fastening material Ordering Information Article no. Colour PU1 PU4 116.255.21.1 Gloss chrome 1 81 Product and Installation Guide Washroom & Bathroom 2011 33 Product Guide Taps HyTronic185 infra-red sensor tap with internal mixing, mains powered HyTronic185 infra-red sensor tap with internal mixing, battery powered 115 115 Ø 64 Ø 64 16 25° Ø 27-38 14 16 125 25° Ø 27-38 14 02-38 448 125 02-38 448 3/8" 3/8" Application Application • For cold and hot water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top • For cold and hot water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top Characteristics Characteristics • Temperature pre-setting via the internal mixer • Unmixed hot or cold water cannot be adjusted • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Can be changed from mains operation to battery operation • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Volume flow control with aerator • Various functions can be set manually • Watersaver program adjustable • Interval flush program adjustable • Integrated check valve • Electrical power supply via power supply unit • Requires transformer 241.672.00.1 • Temperature pre-setting via the internal mixer • Unmixed hot or cold water cannot be adjusted • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Volume flow control with aerator • Various functions can be set manually • Watersaver program adjustable • Interval flush program adjustable • Integrated check valve • Power supply by battery • Battery is sufficient to activate the water flow 200000 times • Warning if the battery is low • Energy saving mode can be set Product Details Differentiated pressure CW/WW ≤ 1.5 bar Product Details Product material Chrome-plated brass Differentiated pressure CW/WW ≤ 1.5 bar 16–18 cm Product material Chrome-plated brass 1–33 cm Activation distance factory setting 16–18 cm Ambient temperature 1–40 °C Activation distance adjustment range 1–33 cm Operating pressure 0.5–8 bar Ambient temperature 1–40 °C 90 °C Operating pressure 0.5–8 bar Flow rate at 3 bar 6 l/min Maximum operating temperature, short-term 90 °C Mains frequency 50 Hz Flow rate at 3 bar 6 l/min 230 V AC Operating voltage 6 V DC Operating voltage 12 V AC Battery type CR - P2 (6 V) Operating temperature water max. 65 °C Operating temperature water max. 65 °C Activation distance factory setting Activation distance adjustment range Maximum operating temperature, short-term Nominal voltage Additional Note 2 metal-reinforced hoses R 3/8"; 2 filters; Key for aerator; 1.5 m connection cable; Power supply unit; Fastening material Additional Note 2 metal-reinforced hoses R 3/8"; 2 filters; 6 V battery; Key for aerator; Fastening material Ordering Information Ordering Information Article no. 116.145.21.1 34 Colour Gloss chrome PU1 1 PU4 Article no. Colour PU1 PU4 81 116.245.21.1 Gloss chrome 1 81 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Taps HyTronic186 infra-red sensor tap without mixer, mains powered HyTronic186 infra-red sensor tap without mixer, battery powered 13 13 Ø 64 12 Ø 64 12 25° 95 Ø 27-38 14 25° 95 Ø 27-38 14 02-38 448 02-38 448 3/8" 3/8" Application Application • For cold or mixed water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top • For cold or mixed water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top Characteristics Characteristics • Temperature is not adjustable • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Can be changed from mains operation to battery operation • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Volume flow control with aerator • Various functions can be set manually • Watersaver program adjustable • Interval flush program adjustable • Integrated check valve • Electrical power supply via power supply unit • Requires transformer 241.672.00.1 • Temperature is not adjustable • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Volume flow control with aerator • Various functions can be set manually • Watersaver program adjustable • Interval flush program adjustable • Integrated check valve • Power supply by battery • Battery is sufficient to activate the water flow 200000 times • Warning if the battery is low • Energy saving mode can be set Product Details Chrome-plated brass Product Details Activation distance factory setting 16–18 cm Product material Chrome-plated brass Activation distance adjustment range 1–33 cm Activation distance factory setting 16–18 cm Ambient temperature 1–40 °C Activation distance adjustment range 1–33 cm Operating pressure 0.5–8 bar Ambient temperature 1–40 °C Maximum operating temperature, short-term 90 °C Operating pressure 0.5–8 bar Flow rate at 3 bar 6 l/min Maximum operating temperature, short-term 90 °C Mains frequency 50 Hz Flow rate at 3 bar 6 l/min Nominal voltage 230 V AC Operating voltage 6 V DC Operating voltage 12 V AC Battery type CR - P2 (6 V) Max. operating temperature mixed water 45 °C Max. operating temperature mixed water 45 °C Product material Additional Note Metal-reinforced hose R 3/8"; Filter; Key for aerator; 1.5 m connection cable; Power supply unit; Fastening material Additional Note Metal-reinforced hose R 3/8"; Filter; 6 V battery; Key for aerator; Fastening material Ordering Information Ordering Information Article no. Colour PU1 PU4 Article no. Colour PU1 PU4 116.136.21.1 Gloss chrome 1 81 116.236.21.1 Gloss chrome 1 81 Product and Installation Guide Washroom & Bathroom 2011 35 Product Guide Taps HyTronic186 infra-red sensor tap with mixer lever, mains powered HyTronic186 infra-red sensor tap with mixer lever, battery powered 13 13 Ø 64 12 Ø 64 25° 95 Ø 27-38 14 12 25° 95 Ø 27-38 02-38 14 448 02-38 448 3/8" 3/8" Application • For cold and hot water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top Application • For cold and hot water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top Characteristics • Temperature adjustment via the mixer lever • Unmixed hot or cold water cannot be adjusted • Proportion of hot water can be limited • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Can be changed from mains operation to battery operation • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Volume flow control with aerator • Various functions can be set manually • Watersaver program adjustable • Interval flush program adjustable • Integrated check valve • Electrical power supply via power supply unit • Requires transformer 241.672.00.1 Product Details Characteristics • Temperature adjustment via the mixer lever • Unmixed hot or cold water cannot be adjusted • Proportion of hot water can be limited • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Volume flow control with aerator • Various functions can be set manually • Watersaver program adjustable • Interval flush program adjustable • Integrated check valve • Power supply by battery • Battery is sufficient to activate the water flow 200000 times • Warning if the battery is low • Energy saving mode can be set Differentiated pressure CW/WW ≤ 1.5 bar Product material Chrome-plated brass Product Details Activation distance factory setting 16–18 cm Differentiated pressure CW/WW ≤ 1.5 bar Activation distance adjustment range 1–33 cm Product material Chrome-plated brass Ambient temperature 1–40 °C Activation distance factory setting 16–18 cm Operating pressure 0.5–8 bar Activation distance adjustment range 1–33 cm Maximum operating temperature, short-term 90 °C Ambient temperature 1–40 °C Flow rate at 3 bar 6 l/min Operating pressure 0.5–8 bar Mains frequency 50 Hz Maximum operating temperature, short-term 90 °C Nominal voltage 230 V AC Flow rate at 3 bar Operating voltage 12 V AC Operating voltage 6 V DC Operating temperature water max. 65 °C Battery type CR - P2 (6 V) Operating temperature water max. 65 °C Additional Note 2 metal-reinforced hoses R 3/8"; 2 filters; Key for aerator; 1.5 m connection cable; Power supply unit; Fastening material Ordering Information Article no. Colour PU1 PU4 116.156.21.1 Gloss chrome 1 81 36 6 l/min Additional Note 2 metal-reinforced hoses R 3/8"; 2 filters; 6 V battery; Key for aerator; Fastening material Ordering Information Article no. Colour PU1 PU4 116.256.21.1 Gloss chrome 1 81 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Taps HyTronic186 infra-red sensor tap with internal mixing, mains powered HyTronic186 infra-red sensor tap with internal mixing, battery powered 13 13 Ø 64 12 Ø 64 25° 95 Ø 27-38 14 12 25° 95 Ø 27-38 02-38 14 448 02-38 448 3/8" 3/8" Application • For cold and hot water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top Application • For cold and hot water connection • For extracting tap water • For public and semi-public areas • For installation in washbasin or work top Characteristics • Temperature pre-setting via the internal mixer • Unmixed hot or cold water cannot be adjusted • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Can be changed from mains operation to battery operation • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Volume flow control with aerator • Various functions can be set manually • Watersaver program adjustable • Interval flush program adjustable • Integrated check valve • Electrical power supply via power supply unit • Requires transformer 241.672.00.1 Product Details Characteristics • Temperature pre-setting via the internal mixer • Unmixed hot or cold water cannot be adjusted • Infra-red user detection • Automatic triggering • Self-calibrating infra-red control • Vandal-proof • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Volume flow control with aerator • Various functions can be set manually • Watersaver program adjustable • Interval flush program adjustable • Integrated check valve • Power supply by battery • Battery is sufficient to activate the water flow 200000 times • Warning if the battery is low • Energy saving mode can be set Differentiated pressure CW/WW ≤ 1.5 bar Product material Chrome-plated brass Product Details Activation distance factory setting 16–18 cm Differentiated pressure CW/WW ≤ 1.5 bar Activation distance adjustment range 1–33 cm Product material Chrome-plated brass Ambient temperature 1–40 °C Activation distance factory setting 16–18 cm Operating pressure 0.5–8 bar Activation distance adjustment range 1–33 cm Maximum operating temperature, short-term 90 °C Ambient temperature 1–40 °C Flow rate at 3 bar 6 l/min Operating pressure 0.5–8 bar Mains frequency 50 Hz Maximum operating temperature, short-term 90 °C Nominal voltage 230 V AC Flow rate at 3 bar 6 l/min Operating voltage 12 V AC Operating voltage 6 V DC Operating temperature water max. 65 °C Battery type CR - P2 (6 V) Operating temperature water max. 65 °C Additional Note 2 metal-reinforced hoses R 3/8"; 2 filters; Key for aerator; 1.5 m connection cable; Power supply unit; Fastening material Ordering Information Article no. Colour PU1 PU4 116.146.21.1 Gloss chrome 1 81 Additional Note 2 metal-reinforced hoses R 3/8"; 2 filters; 6 V battery; Key for aerator; Fastening material Ordering Information Article no. Colour PU1 PU4 116.246.21.1 Gloss chrome 1 81 Product and Installation Guide Washroom & Bathroom 2011 37 Product Guide Taps HyTronic87 infra-red sensor tap without mixer, mains powered 13 HyTronic87 infra-red sensor tap with mixer lever, mains powered 13 165 165 15 15 R1/2 13 13 25° R1/2 R1/2 25° 55 25° 14 55 25° 14 Application Application • For wall mounted installation • For public and semi-public areas • For concealed installation • For use in the hygiene area • For use in the industrial area • For use in the Geberit Duofix system • For cold or mixed water connection • For wall mounted installation • For public and semi-public areas • For concealed installation • For use in the hygiene area • For use in the industrial area • For use in the Geberit Duofix system • For cold or mixed water connection Characteristics Characteristics • Automatic triggering • Self-calibrating infra-red control • Interval flush program adjustable • Watersaver program adjustable • Various functions can be set manually • Vandal-proof • Volume flow control with aerator • Compatible with the MeplaFix water supply connection • Temperature is not adjustable • Electrical power supply via power supply unit • Requires transformer 241.672.00.1 or 241.631.00.1 • Requires the HansaVarox concealed base unit 616.030.00.1 • Automatic triggering • Self-calibrating infra-red control • Interval flush program adjustable • Watersaver program adjustable • Various functions can be set manually • Vandal-proof • Volume flow control with aerator • Compatible with the MeplaFix water supply connection • Temperature adjustment via the mixer lever • Electrical power supply via power supply unit • Requires transformer 241.672.00.1 or 241.631.00.1 • Requires the HansaVarox concealed base unit 616.030.00.1 Product Details Product Details ≤ 1.5 bar Flow rate with tap aerator 6l/min Differentiated pressure CW/WW Flow rate >0.1 l/s Flow rate with tap aerator 6l/min Relative humidity ≤ 100% Flow rate >0.1 l/s Product material Brass / chrome-plated die-cast zinc Relative humidity ≤ 100% Activation distance adjustment range 1–33 cm Product material Brass / chrome-plated die-cast zinc Operating pressure 0.5–8 bar Activation distance adjustment range 1–33 cm Operating temperature 1–40 °C Operating pressure 0.5–8 bar Maximum operating temperature, short-term 90 °C Operating temperature 1–40 °C Max. operating temperature mixed water 45 °C Maximum operating temperature, short-term 90 °C Activation distance factory setting 16–18 cm Activation distance factory setting 16–18 cm Mains frequency 50 Hz Mains frequency 50 Hz Nominal voltage 230 V AC Nominal voltage 230 V AC Operating voltage 12 V AC Operating voltage 12 V AC Additional Note Non-return valve; Filter; Key for aerator; 1.5 m connection cable; Fastening material Additional Note 2 non-return valves; 2 filters; Key for aerator; 1.5 m connection cable; Fastening material Excluded: Power supply unit Excluded: Power supply unit Ordering Information Ordering Information Article no. Colour PU1 PU4 Article no. Colour PU1 PU4 116.107.21.1 Gloss chrome 1 60 116.127.21.1 Gloss chrome 1 60 38 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Taps HyTronic87 infra-red sensor tap with internal mixing, mains powered 13 HyTronic88 infra-red sensor tap without mixer, mains powered 13 165 215 15 15 13 R1/2 R1/2 R1/2 13 25° 25° 55 55 25° 25° 14 19 Application Application • For wall mounted installation • For public and semi-public areas • For concealed installation • For use in the hygiene area • For use in the industrial area • For use in the Geberit Duofix system • For cold or mixed water connection • For wall mounted installation • For public and semi-public areas • For concealed installation • For use in the hygiene area • For use in the industrial area • For use in the Geberit Duofix system • For cold or mixed water connection Characteristics Characteristics • Automatic triggering • Self-calibrating infra-red control • Interval flush program adjustable • Watersaver program adjustable • Various functions can be set manually • Vandal-proof • Volume flow control with aerator • Compatible with the MeplaFix water supply connection • Temperature pre-setting via the internal mixer • Electrical power supply via power supply unit • Requires transformer 241.672.00.1 or 241.631.00.1 • Requires the HansaVarox concealed base unit 616.030.00.1 • Automatic triggering • Self-calibrating infra-red control • Interval flush program adjustable • Watersaver program adjustable • Various functions can be set manually • Vandal-proof • Volume flow control with aerator • Compatible with the MeplaFix water supply connection • Temperature is not adjustable • Electrical power supply via power supply unit • Requires transformer 241.672.00.1 or 241.631.00.1 • Requires the HansaVarox concealed base unit 616.030.00.1 Product Details Product Details ≤ 1.5 bar Differentiated pressure CW/WW Flow rate with tap aerator 6l/min Flow rate >0.1 l/s Relative humidity ≤ 100% Flow rate with tap aerator 6l/min Flow rate >0.1 l/s Relative humidity ≤ 100% Product material Brass / chrome-plated die-cast zinc Product material Brass / chrome-plated die-cast zinc Activation distance adjustment range 1–33 cm Operating pressure 0.5–8 bar 1–33 cm Operating temperature 1–40 °C Operating pressure 0.5–8 bar Maximum operating temperature, short-term 90 °C Operating temperature 1–40 °C Max. operating temperature mixed water Activation distance adjustment range 45 °C Maximum operating temperature, short-term 90 °C Activation distance factory setting 16–18 cm Activation distance factory setting 16–18 cm Mains frequency 50 Hz Mains frequency 50 Hz Nominal voltage 230 V AC Nominal voltage 230 V AC Operating voltage 12 V AC Operating voltage 12 V AC Additional Note 2 non-return valves; 2 filters; Key for aerator; 1.5 m connection cable; Fastening material Additional Note Non-return valve; Filter; Key for aerator; 1.5 m connection cable; Fastening material Excluded: Power supply unit Excluded: Power supply unit Ordering Information Ordering Information Article no. Colour PU1 PU4 116.117.21.1 Gloss chrome 1 60 Article no. Colour PU1 PU4 116.108.21.1 Gloss chrome 1 60 Product and Installation Guide Washroom & Bathroom 2011 39 Product Guide Taps HyTronic88 infra-red sensor tap with internal mixing, mains powered HyTronic88 infra-red sensor tap with mixer lever, mains powered 13 13 215 215 15 15 13 R1/2 R1/2 13 25° R1/2 R1/2 25° 55 55 25° 25° 19 19 Application Application • For wall mounted installation • For public and semi-public areas • For concealed installation • For use in the hygiene area • For use in the industrial area • For use in the Geberit Duofix system • For cold or mixed water connection • For wall mounted installation • For public and semi-public areas • For concealed installation • For use in the hygiene area • For use in the industrial area • For use in the Geberit Duofix system • For cold or mixed water connection Characteristics Characteristics • Automatic triggering • Self-calibrating infra-red control • Interval flush program adjustable • Watersaver program adjustable • Various functions can be set manually • Vandal-proof • Volume flow control with aerator • Compatible with the MeplaFix water supply connection • Temperature adjustment via the mixer lever • Electrical power supply via power supply unit • Requires transformer 241.672.00.1 or 241.631.00.1 • Requires the HansaVarox concealed base unit 616.030.00.1 • Automatic triggering • Self-calibrating infra-red control • Interval flush program adjustable • Watersaver program adjustable • Various functions can be set manually • Vandal-proof • Volume flow control with aerator • Compatible with the MeplaFix water supply connection • Temperature pre-setting via the internal mixer • Electrical power supply via power supply unit • Requires transformer 241.672.00.1 or 241.631.00.1 • Requires the HansaVarox concealed base unit 616.030.00.1 Product Details Product Details Differentiated pressure CW/WW ≤ 1.5 bar Differentiated pressure CW/WW Flow rate with tap aerator 6l/min Flow rate with tap aerator 6l/min Flow rate >0.1 l/s Flow rate >0.1 l/s Relative humidity ≤ 100% Relative humidity ≤ 100% Product material Brass / chrome-plated die-cast zinc Product material Brass / chrome-plated die-cast zinc Activation distance adjustment range 1–33 cm Activation distance adjustment range 1–33 cm Operating pressure 0.5–8 bar Operating pressure 0.5–8 bar Operating temperature 1–40 °C Operating temperature 1–40 °C ≤ 1.5 bar Maximum operating temperature, short-term 90 °C Maximum operating temperature, short-term 90 °C Activation distance factory setting 16–18 cm Activation distance factory setting 16–18 cm Mains frequency 50 Hz Mains frequency 50 Hz Nominal voltage 230 V AC Nominal voltage 230 V AC Operating voltage 12 V AC Operating voltage 12 V AC Additional Note 2 non-return valves; 2 filters; Key for aerator; 1.5 m connection cable; Fastening material Additional Note 2 non-return valves; 2 filters; Key for aerator; 1.5 m connection cable; Fastening material Excluded: Power supply unit Excluded: Power supply unit Ordering Information Ordering Information Article no. Colour PU1 PU4 Article no. Colour PU1 PU4 116.128.21.1 Gloss chrome 1 60 116.118.21.1 Gloss chrome 1 60 40 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Taps Transformer for HyTronic185/186 and HyTronic87/88 HansaVarox box for HyTronic87 and 88 R D D1 R Z Application • For power supply of HyTronic87/88 and HyTronic185/186 outlet taps l Z H L1 H L Characteristics Characteristics • Power supply of up to 8 taps • Transformation of mains voltage to extra-low voltage • MeplaFix system elbow made from dezincification-resistant brass • Acoustically decoupled • For mounting HyTronic87/88 wall-hung taps Product Details Nominal voltage 230 V AC Output voltage 12 V AC Additional Note 2 MeplaFix system elbows, pre-mounted; 1 MeplaFix system elbow, loose, with seal; Rubber collar; Fastening ring Ordering Information Ordering Information Article no. PU1 Article no. 241.672.00.1 1 R '' 616.030.00.1 MF 1/2 10,4 11 D cm D1 cm H cm L cm L1 cm l cm Z cm 7 14 11 2 5,5 Roughing box and transformer for HyTronic185/186 and HyTronic87/88 77 77 Application • For concealed installation in solid or drywall construction • For power supply of HyTronic87/88 and HyTronic185/186 outlet taps Characteristics • Power supply of up to 8 taps • Transformation of mains voltage to extra-low voltage Product Details Nominal voltage 230 V AC Mains frequency 50–60 Hz Output voltage 12 V AC Protection degree IP 20 Additional Note Power supply unit; Concealed outlet for drilling diameter ø 76 mm; Cover for concealed outlet; Conduit pipe, 1.7 m Ordering Information Article no. PU1 241.631.00.1 1 Product and Installation Guide Washroom & Bathroom 2011 41 Product Guide Duofix bidet frames Duofix bidet frame 0.98 m Duofix bidet frames Duofix bidet frames Duofix bidet frame 1.12 m 4 50 4 50 100 8-38 98 18/23 964.160.00.0 112 0 0 8-38 18/23 964.160.00.0 0-20 0-20 350 330340 360 310 964.161.00.0 290300 320 270 250260 280 230 210220 240 190 170180 200 150 130140 160 110 90100 120 80 90 110100 80 130 150140 120 170 190180 160 210 230220 200 250 270260 240 290 310300 280 330 350340 320 360 73 964.162.00.0 964.160.00.0 0 0 0-20 0-20 73 48 10 Application • For installation of a wall-hung bidet with bolt fixings set at 180 or 230 mm centres • For installation in a room-high Duofix system wall • For installation in a load bearing stud wall • For a screed of 0 - 200 mm 48 10 Application • For installation of a wall-hung bidet with bolt fixings set at 180 or 230 mm centres • For installation in a partial-height Duofix system wall in front of a solid or drywall construction • For mounting in front of a solid or drywall construction (order PreWall brackets 111.844.00.1 separately) • For a screed of 0 - 200 mm Characteristics Characteristics • Frame height 1120 mm • Bidet fastening distance 180 mm or 230 mm • Frame with holes ø 9 mm for fastening in wood frame construction • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • With wall brackets to allow up to a 200 mm duct. For larger ducts up to 400 mm use extension bolts 111.887.00.1 • With backplate elbows and chrome isolating valves with 3/8" BSP connection Additional Note 2 water connections R 1/2"; 2 angle stop valves R 1/2"; 2 Duofix PreWall brackets for system; 2 threaded rods M12 for ceramics fastening; Fastening material • Frame height 980 mm • Bidet fastening distance 180 mm or 230 mm • Frame with holes ø 9 mm for fastening in wood frame construction • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • With wall brackets to allow up to a 200 mm duct. For larger ducts up to 400 mm use extension bolts 111.887.00.1 • With backplate elbows and chrome isolating valves with 3/8" BSP connection Additional Note 2 water connections R 1/2"; 2 angle stop valves R 1/2"; 2 Duofix PreWall brackets for system; 2 threaded rods M12 for ceramics fastening; Fastening material Ordering Information Ordering Information Article no. PU1 111.545.00.1 1 42 Article no. PU1 111.544.00.1 1 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Duofix urinal frames Duofix bidet frame 0.82 m Duofix urinal frames Duofix urinal frames 50 4 Duofix urinal frame with pipe interruptor for mains fed water supply 500 8-38 18/23 82 75 90 R1/2 1180 350 330340 360 310 964.161.00.0 290300 320 270 250260 280 230 210220 240 190 170180 200 150 130140 160 110 90100 120 80 90 110100 80 130 150140 120 170 190180 160 210 230220 200 250 270260 240 290 310300 280 330 350340 320 360 964.162.00.0 964.160.00.0 0 0 0-20 1000 320-360 0-20 73 48 75-330 10 1300 Application • For installation of a wall-hung bidet with bolt fixings set at 180 or 230 mm centres • For installation in a partial-height Duofix system wall in front of a solid or drywall construction • For mounting in front of a solid or drywall construction (order PreWall brackets 111.844.00.1 separately) • For a screed of 0 - 200 mm Characteristics • Frame height 820 mm • Bidet fastening distance 180 mm or 230 mm • Frame with holes ø 9 mm for fastening in wood frame construction • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • With wall brackets to allow up to a 200 mm duct. For larger ducts up to 400 mm use extension bolts 111.887.00.1 • With backplate elbows and chrome isolating valves with 3/8" BSP connection Additional Note 2 water connections R 1/2"; 2 angle stop valves R 1/2"; 2 Duofix PreWall brackets for system; 2 threaded rods M12 for ceramics fastening; Fastening material Ordering Information Article no. PU1 111.543.00.1 1 0 0 0-200 48 Application 73 • For installation of wall-hung urinals • For installation in a half-height Duofix system wall in front of a solid or drywall construction • For installation in a room-high Duofix system wall in front of a solid or drywall construction • For installing in a load bearing stud wall • For mounting in front of a solid or drywall construction (order PreWall brackets 111.844.00.1 separately) • For a screed of 0 - 200 mm (not in room height applications) • For mains fed water supply (note: Geberit urinal controls need a minimum 1 bar supply) • For Geberit concealed urinal control • Not suitable for urinals with spreaders Characteristics • Frame with holes ø 9 mm for fastening in wood frame construction • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Frame height from 112 cm to 130 cm, depending on urinal • Water supply connection 1/2" (compatible with MeplaFix) • Water supply connection can be installed without tools • Water supply connection radially sealing • Stop valve with throttle pre-mounted • Pre-mounted conduit pipe for rinsing the pipe • Terminal provided • The protection cover protects the service opening against moisture and dirt • Protection housing for service opening, can be cut to length • Flexible connection hose between concealed housing and inlet • Inlet ø 32 mm, height-adjustable • Fastening for urinal with M8 threaded rod, adjustable height and distance • Fastening for outlet bend sound-absorbing and height-adjustable • Self-locking feet for tool-free alignment of the element. (Friction feet have to be locked with spanner) • Additional fastening possible for urinal with accessories • Conversion possible for urinals with spray head with accessories • Mechanical pipe interruptor for mains water connection • Please see page 119 for details of pipe interruptor drainage installation Product and Installation Guide Washroom & Bathroom 2011 43 Product Guide Duofix urinal frames Duofix urinal frame for tank fed water supply Product Details Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Relative humidity < 100 % 12-32 Operating pressure 1–8 bar min. 9 Max. test pressure water 16 bar Max. test pressure air / inert gas 3 bar Operating temperature water max. 50 Ordering Information Article no. PU1 111.622.00.1 1 9 100-118 R1/2 17-37 75-33 112-130 max. 65 30 °C Additional Note Concealed housing with water section; Protection box with cover; Water supply connection R 1/2"; Connection pipe between inlet ø 32 mm and urinal, incl. seal on urinal; Suction trap ø 50 mm, incl. seal to urinal; Outlet pipe, PVC, ø 50 mm, incl. seal on the suction trap; 2 threaded rods M8 for urinal fastening; Fastening material Excluded: Urinal flushing system 75 0 0 0-20 0-20 73 48 Application • For installation of wall-hung urinals • For tank fed water supply (note: Geberit urinal controls need a minimum 1 bar supply) • For mains fed water with urinals Ideal Standard Jasper Morrison, Villeroy & Boch Omina Classic (#7557), Duravit Starck 3 (#082135), Kohler Odela • For installation in a half-height Duofix system wall in front of a solid or drywall construction • For installation in a room-high Duofix system wall in front of a solid or drywall construction • For installing in a load bearing stud wall • For mounting in front of a solid or drywall construction (order PreWall brackets 111.844.00.1 separately) • For a screed of 0 - 200 mm (not in room height applications) • For Geberit concealed urinal control • Not suitable for urinals with spreaders Characteristics • Frame with holes ø 9 mm for fastening in wood frame construction • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Frame height from 112 cm to 130 cm, depending on urinal • Water supply connection 1/2" (compatible with MeplaFix) • Water supply connection can be installed without tools • Water supply connection radially sealing • Stop valve with throttle pre-mounted • Pre-mounted conduit pipe for rinsing the pipe • Terminal provided • The protection cover protects the service opening against moisture and dirt • Protection housing for service opening, can be cut to length • Flexible connection hose between concealed housing and inlet • Inlet ø 32 mm, height-adjustable • Fastening for urinal with M8 threaded rod, adjustable height and distance • Fastening for outlet bend sound-absorbing and height-adjustable • Self-locking feet for tool-free alignment of the element. (Friction feet have to be locked with spanner) • Additional fastening possible for urinal with accessories • Conversion possible for urinals with spray head with accessories Product Details 44 Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Relative humidity < 100 % Operating pressure 1–8 bar Max. test pressure water 16 bar Max. test pressure air / inert gas 3 bar Operating temperature water max. 30 °C Product and Installation Guide Washroom & Bathroom 2011 Product Guide Duofix urinal frames Additional Note Concealed housing with water section; Protection box with cover; Water supply connection R 1/2"; Connection pipe between inlet ø 32 mm and urinal, incl. seal on urinal; Suction trap ø 50 mm, incl. seal to urinal; Outlet pipe, PVC, ø 50 mm, incl. seal on the suction trap; 2 threaded rods M8 for urinal fastening; Fastening material Urinal installation set universal 15 R1/2 Excluded: Urinal flushing system 7 1-9 105 Ordering Information 105 15 Article no. PU1 PU4 111.623.00.1 1 14 117 Application • For concealed installation in solid constructions • For accommodating the HyTronic infra-red urinal controls or HyTouch pneumatic urinal controls • For mains fed water with urinals Ideal Standard Jasper Morrison, Villeroy & Boch Omina Classic (#7557), Duravit Starck 3 (#082135), Kohler Odela • For tank fed water supply (note: Geberit urinal controls need a minimum 1 bar supply) Characteristics • Water connection at the top centre • Water supply connection 1/2" (compatible with MeplaFix) • Water supply connection can be installed without tools • Water supply connection radially sealing • Stop valve with throttle pre-mounted • Pre-mounted conduit pipe for rinsing the pipe • Terminal provided • The protection cover protects the service opening against moisture and dirt • Protection housing for service opening, can be cut to length Product Details Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Operating pressure 1–8 bar Max. test pressure water 16 bar Relative humidity 95 % Operating temperature water max. 30 °C Additional Note Concealed housing with water section; Protection box with cover; Water supply connection R 1/2" Ordering Information Article no. PU1 116.001.00.1 1 Product and Installation Guide Washroom & Bathroom 2011 45 Product Guide Duofix urinal frames Duofix mounting plate for urinal division Urinal installation set universal with flush pipe 15 R1/2 7 35 1-9 105 105 15 50 max. 61 Application Application • For concealed installation in solid constructions • For accommodating the HyTronic infra-red urinal controls or HyTouch pneumatic urinal controls • For tank fed water supply (note: Geberit urinal controls need a minimum 1 bar supply) • For mains fed water with urinals Ideal Standard Jasper Morrison, Villeroy & Boch Omina Classic (#7557), Duravit Starck 3 (#082135), Kohler Odela • For installation in a half-height Duofix system wall in front of a solid or drywall construction • For installation in a room-high Duofix system wall in front of a solid or drywall construction • For installation in a load bearing stud wall • For installation of urinal division Characteristics • Multi-layered, water-resistant bonding • Veneered wood plate • Can be cut to reduce distance between urinals Product Details Product material Wood Characteristics • Water connection at the top centre • Water supply connection 1/2" (compatible with MeplaFix) • Water supply connection can be installed without tools • Water supply connection radially sealing • Stop valve with throttle pre-mounted • Pre-mounted conduit pipe for rinsing the pipe • Terminal provided • The protection cover protects the service opening against moisture and dirt • Protection housing for service opening, can be cut to length Additional Note 8 fastening brackets; Fastening material Ordering Information Article no. PU1 PU4 111.859.00.1 1 40 Urinal division Product Details Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Operating pressure 1–8 bar Max. test pressure water 16 bar Relative humidity 95 % Operating temperature water max. 30 °C 92-98 74 44 Additional Note Concealed housing with water section; Protection box with cover; Water supply connection R 1/2"; Flush pipe D32 0 Ordering Information Application Article no. PU1 • For separating urinals mounted adjacent to one another 116.003.00.1 1 Characteristics • Plastic urinal partition with concealed fastening • Corrosion-resistant bracket, hard-anodised surface Additional Note Distance bolts; Fastening material Ordering Information 46 Article no. Colour PU1 PU4 115.200.11.1 White 1 16 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Duofix urinal frames HyTouch hand operated pneumatic urinal control, Sigma10 Glass urinal division 08 13 13 95-105 75 93 50 13 35 75 525 Application 0 • For manual flush actuation of urinals • For assembly in urinal installation set 4 Application • For separating urinals mounted adjacent to one another • For mounting on solid or drywall constructions Characteristics • Manual flush actuation • Low flush actuation force • Flush actuation when the actuator button is released • Flush time setting with air nozzles (pneumatic) • Plastic actuator plate, with securing bar Characteristics • Concealed installation • Corrosion-resistant bracket, hard-anodised surface • Matt glass surface on both sides Product Details Product Details Product material ESG - (toughened safety glass) Additional Note Wall bracket; Cover; Fastening material Ordering Information Actuation force < 12 N Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Operating pressure 1–8 bar Max. test pressure water 16 bar Max. test pressure air / inert gas 3 bar PU1 PU4 Operating temperature water max. 30 °C 115.210.CD.1 Opaque grey 1 15 Relative humidity < 100 % 115.210.GT.1 1 Flush time range 4 / 8 / 12 s Article no. Colour Opaque green Additional Note Flush plate; Pneumatic control, pre-mounted on mounting frame; Pneumatic valve; Fastening material Glass urinal division 08 Ordering Information Article no. 95-105 80 50 75 Colour 116.015.KH.1 Gloss chrome / matt chrome / gloss chrome 116.015.KJ.1 White / gloss chrome / white PU1 1 1 35 116.015.KK.1 White / gold-plated / white 1 75 116.015.KL.1 1 496 White / matt chrome / matt chrome 116.015.KM.1 Black / gloss chrome / black 1 116.015.KN.1 Matt chrome / gloss chrome / matt chrome 1 4 0 Application • For separating urinals mounted adjacent to one another • For mounting on solid or drywall constructions Characteristics • Concealed installation • Corrosion-resistant bracket, hard-anodised surface • Matt glass surface on both sides Product Details Product material ESG - (toughened safety glass) Additional Note Wall bracket; Cover; Fastening material Ordering Information PU1 PU4 115.214.CD.1 Opaque grey Article no. Colour 1 15 115.214.GT.1 1 15 Opaque green Product and Installation Guide Washroom & Bathroom 2011 47 Product Guide Duofix urinal frames HyTronic infra-red urinal control, battery powered, Sigma10 HyTronic infra-red urinal control, mains powered, Sigma10 13 1 13 1 13 13 Application Application • For automatic flush actuation of urinals • For assembly in installation set • For automatic flush actuation of urinals • For assembly in installation set Characteristics • Automatic flush actuation, user-controlled • Infra-red detection with background fade-out • Ready for operation after mains connection • Power-failure control system • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Dynamic flushing time adjustment • Die-cast zinc cover plate, with securing bar Characteristics • Automatic flush actuation, user-controlled • Infra-red detection with background fade-out • Warning if the battery is low • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Dynamic flushing time adjustment • Die-cast zinc cover plate, with securing bar Product Details Product Details 110–240 V AC Operating voltage 3 V DC 50–60 Hz Power consumption < 0.5 W < 0.5 W Protection degree IP 45 4.5 V DC Battery type Lithium battery 1.5 V (AA) Protection degree IP 45 Lifetime lithium battery ~ 2 years Flow rate at 1 bar without flow limiter 0.3 l/s Lifetime alkaline battery ~ 1.5 years Flow rate at 1 bar with flow limiter 0,24 l/s Flow rate at 1 bar without flow limiter 0.3 l/s Operating pressure 1–8 bar Flow rate at 1 bar with flow limiter 0,24 l/s Max. test pressure water 16 bar Operating pressure 1–8 bar Max. test pressure air / inert gas 3 bar Max. test pressure water 16 bar 30 °C Max. test pressure air / inert gas 3 bar < 100 % Operating temperature water max. 30 °C 4s Relative humidity < 100 % 3–15 s Flush time factory setting 4s Activation time 7s Flush time range 3–15 s Activation time range 3–15 s Activation time 7s 24 h Activation time range 3–15 s 1–168 h Interval flush factory setting 24 h Interval flush adjustment range 1–168 h Nominal voltage Mains frequency Power consumption Operating voltage Operating temperature water max. Relative humidity Flush time factory setting Flush time range Interval flush factory setting Interval flush adjustment range Additional Note Cover plate with infra-red window; Infra-red control, premounted on mounting frame; Power supply unit; Solenoid valve; Fastening material Ordering Information Article no. Colour PU1 116.025.KH.1 Gloss chrome / matt chrome / gloss chrome 1 116.025.KJ.1 1 White / gloss chrome / white 116.025.KK.1 White / gold-plated / white 1 116.025.KL.1 1 White / matt chrome / matt chrome 116.025.KM.1 Black / gloss chrome / black 1 116.025.KN.1 Matt chrome / gloss chrome / matt chrome 1 48 Additional Note Cover plate with infra-red window; Infra-red control, premounted on mounting frame; Battery box; 2 lithium batteries; Solenoid valve; Fastening material Ordering Information Article no. Colour PU1 116.035.KH.1 Gloss chrome / matt chrome / gloss chrome 1 116.035.KJ.1 1 White / gloss chrome / white 116.035.KK.1 White / gold-plated / white 1 116.035.KL.1 1 White / matt chrome / matt chrome 116.035.KM.1 Black / gloss chrome / black 1 116.035.KN.1 Matt chrome / gloss chrome / matt chrome 1 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Duofix urinal frames HyTouch hand operated pneumatic urinal control, Sigma50 HyTouch hand operated pneumatic urinal control, Sigma50 - bespoke cover 13 13 14 13 14 13 Application Application • For manual flush actuation of urinals • For assembly in installation set • For manual flush actuation of urinals • For assembly in installation set Characteristics Characteristics • Manual flush actuation • Low flush actuation force • Flush actuation when the actuator button is released • Flush time setting with air nozzles (pneumatic) • Die-cast zinc actuator plate, with securing bar • Manual flush actuation • Low flush actuation force • Flush actuation when the actuator button is released • Flush time setting with air nozzles (pneumatic) • Die-cast zinc actuator plate, with securing bar Product Details Product Details Actuation force < 12 N Actuation force Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar without flow limiter < 12 N 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Operating pressure 1–8 bar Operating pressure 1–8 bar Max. test pressure water 16 bar Max. test pressure water 16 bar Max. test pressure air / inert gas 3 bar Max. test pressure air / inert gas 3 bar Operating temperature water max. 30 °C Operating temperature water max. 30 °C Relative humidity < 100 % Relative humidity < 100 % Flush time range 4 / 8 / 12 s Flush time range 4 / 8 / 12 s Additional Note Flush plate; Pneumatic control, pre-mounted on mounting frame; Pneumatic valve; Fastening material Additional Note Flush plate; Pneumatic control, pre-mounted on mounting frame; Pneumatic valve; Fastening material Ordering Information Ordering Information Article no. Colour PU1 Article no. Colour PU1 116.016.00.1 Bespoke 1 116.016.11.1 White alpine 1 116.016.DW.1 Black RAL 9005 1 116.016.EP.1 Pergamon 1 116.016.SE.1 Green satinised 1 116.016.SD.1 Smoked glass reflective 1 116.016.SC.1 White with ornament x 1 Product and Installation Guide Washroom & Bathroom 2011 49 Product Guide Duofix urinal frames HyTronic infra-red urinal control, battery powered, Sigma50 HyTronic infra-red urinal control, mains powered, Sigma50 13 1 13 1 13 13 Application Application • For automatic flush actuation of urinals • For assembly in installation set • For automatic flush actuation of urinals • For assembly in installation set Characteristics Characteristics • Automatic flush actuation, user-controlled • Infra-red detection with background fade-out • Ready for operation after mains connection • Power-failure control system • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Dynamic flushing time adjustment • Die-cast zinc cover plate, with securing bar • Automatic flush actuation, user-controlled • Infra-red detection with background fade-out • Warning if the battery is low • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Dynamic flushing time adjustment • Die-cast zinc cover plate, with securing bar Product Details Product Details Operating voltage 3 V DC Power consumption < 0.5 W 50–60 Hz Protection degree IP 45 < 0.5 W Battery type Lithium battery 1.5 V (AA) Operating voltage 4.5 V DC Lifetime lithium battery ~ 2 years Protection degree IP 45 Lifetime alkaline battery ~ 1.5 years Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Operating pressure 1–8 bar Operating pressure 1–8 bar Max. test pressure water 16 bar Max. test pressure water 16 bar 3 bar Max. test pressure air / inert gas 3 bar 30 °C Operating temperature water max. 30 °C < 100 % Relative humidity < 100 % 4s Flush time factory setting 4s Flush time range 3–15 s Flush time range 3–15 s Activation time 7s Activation time 7s 3–15 s Activation time range 3–15 s 24 h Interval flush factory setting 24 h 1–168 h Interval flush adjustment range 1–168 h 110–240 V AC Nominal voltage Mains frequency Power consumption Max. test pressure air / inert gas Operating temperature water max. Relative humidity Flush time factory setting Activation time range Interval flush factory setting Interval flush adjustment range Additional Note Cover plate with infra-red window; Infra-red control, premounted on mounting frame; Power supply unit; Solenoid valve; Fastening material Ordering Information Article no. Colour 116.026.GH.1 Brushed chrome 50 Additional Note Cover plate with infra-red window; Infra-red control, premounted on mounting frame; Battery box; 2 lithium batteries; Solenoid valve; Fastening material Ordering Information PU1 1 Article no. Colour 116.036.GH.1 Brushed chrome Product and Installation Guide Washroom & Bathroom 2011 PU1 1 Product Guide Duofix urinal frames HyTronic infra-red urinal control, mains powered, Samba HyTouch hand operated pneumatic urinal control, Samba 13 13 09 13 09 13 Application • For automatic flush actuation of urinals • For assembly in installation set Application • For manual flush actuation of urinals • For assembly in installation set Characteristics • Automatic flush actuation, user-controlled • Infra-red detection with background fade-out • Ready for operation after mains connection • Power-failure control system • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Dynamic flushing time adjustment • Die-cast zinc cover plate, with securing bar Characteristics • Manual flush actuation • Low flush actuation force • Flush actuation when the actuator button is released • Flush time setting with air nozzles (pneumatic) • Plastic actuator plate, with securing bar Product Details Product Details Actuation force < 12 N Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Operating pressure 1–8 bar Max. test pressure water 16 bar Max. test pressure air / inert gas 3 bar Operating temperature water max. 30 °C Relative humidity < 100 % Flush time range 4 / 8 / 12 s Additional Note Flush plate; Pneumatic control, pre-mounted on mounting frame; Pneumatic valve; Fastening material Ordering Information Article no. Colour PU1 116.011.11.1 White alpine 1 116.011.21.1 Gloss chrome 1 116.011.46.1 Matt chrome 1 Nominal voltage 110–240 V AC Mains frequency 50–60 Hz Power consumption < 0.5 W Operating voltage 4.5 V DC Protection degree IP 45 Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Operating pressure 1–8 bar Max. test pressure water 16 bar Max. test pressure air / inert gas 3 bar Operating temperature water max. 30 °C Relative humidity < 100 % Flush time factory setting 4s Flush time range 3–15 s Activation time 7s Activation time range 3–15 s Interval flush factory setting 24 h Interval flush adjustment range 1–168 h Additional Note Cover plate with infra-red window; Infra-red control, premounted on mounting frame; Power supply unit; Solenoid valve; Fastening material Ordering Information Article no. Colour PU1 116.021.11.1 White alpine 1 116.021.21.1 Gloss chrome 1 116.021.46.1 Matt chrome 1 Product and Installation Guide Washroom & Bathroom 2011 51 Product Guide Duofix urinal frames HyTronic infra-red urinal control, battery powered, Samba 13 HyTouch hand operated pneumatic urinal control, Bolero 13 09 13 12 13 Application • For manual flush actuation of urinals • For assembly in installation set Application • For automatic flush actuation of urinals • For assembly in installation set Characteristics Characteristics • Automatic flush actuation, user-controlled • Infra-red detection with background fade-out • Warning if the battery is low • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Dynamic flushing time adjustment • Die-cast zinc cover plate, with securing bar Product Details • Manual flush actuation • Low flush actuation force • Flush actuation when the actuator button is released • Flush time setting with air nozzles (pneumatic) • Plastic actuator plate, with securing bar Product Details Actuation force < 12 N Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Operating voltage 3 V DC Operating pressure 1–8 bar Power consumption < 0.5 W Max. test pressure water 16 bar Protection degree IP 45 Max. test pressure air / inert gas 3 bar Battery type Lithium battery 1.5 V (AA) Operating temperature water max. 30 °C Lifetime lithium battery ~ 2 years Relative humidity < 100 % Lifetime alkaline battery ~ 1.5 years Flush time range 4 / 8 / 12 s Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Operating pressure 1–8 bar Additional Note Flush plate; Pneumatic control, pre-mounted on mounting frame; Pneumatic valve; Fastening material Max. test pressure water 16 bar Max. test pressure air / inert gas 3 bar Ordering Information Operating temperature water max. 30 °C Article no. Colour PU1 Relative humidity < 100 % 116.012.11.1 White alpine 1 Flush time factory setting 4s Flush time range 3–15 s 116.012.21.1 Gloss chrome 1 Activation time 7s 116.012.46.1 Matt chrome 1 Activation time range 3–15 s Interval flush factory setting 24 h Interval flush adjustment range 1–168 h Additional Note Cover plate with infra-red window; Infra-red control, premounted on mounting frame; Battery box; 2 lithium batteries; Solenoid valve; Fastening material Ordering Information Article no. Colour PU1 116.031.11.1 White alpine 1 116.031.21.1 Gloss chrome 1 116.031.46.1 Matt chrome 1 52 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Duofix urinal frames HyTronic infra-red urinal control, battery powered, Bolero HyTronic infra-red urinal control, mains powered, Bolero 13 13 12 13 12 13 Application Application • For automatic flush actuation of urinals • For assembly in installation set • For automatic flush actuation of urinals • For assembly in installation set Characteristics • Automatic flush actuation, user-controlled • Infra-red detection with background fade-out • Ready for operation after mains connection • Power-failure control system • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Dynamic flushing time adjustment • Die-cast zinc cover plate, with securing bar Characteristics Product Details Product Details • Automatic flush actuation, user-controlled • Infra-red detection with background fade-out • Warning if the battery is low • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Dynamic flushing time adjustment • Die-cast zinc cover plate, with securing bar Nominal voltage 110–240 V AC Operating voltage 3 V DC Mains frequency 50–60 Hz Power consumption < 0.5 W Power consumption < 0.5 W Protection degree IP 45 Operating voltage 4.5 V DC Battery type Lithium battery 1.5 V (AA) Protection degree IP 45 Lifetime lithium battery ~ 2 years Flow rate at 1 bar without flow limiter 0.3 l/s Lifetime alkaline battery ~ 1.5 years Flow rate at 1 bar with flow limiter 0,24 l/s Flow rate at 1 bar without flow limiter 0.3 l/s Operating pressure 1–8 bar Flow rate at 1 bar with flow limiter 0,24 l/s Max. test pressure water 16 bar Operating pressure 1–8 bar Max. test pressure air / inert gas 3 bar Max. test pressure water 16 bar Operating temperature water max. 30 °C Max. test pressure air / inert gas 3 bar Relative humidity < 100 % Operating temperature water max. 30 °C Flush time factory setting 4s Relative humidity < 100 % Flush time range 3–15 s Flush time factory setting 4s Activation time 7s Flush time range 3–15 s Activation time range 3–15 s Activation time 7s Interval flush factory setting 24 h Activation time range 3–15 s Interval flush adjustment range 1–168 h Interval flush factory setting 24 h Interval flush adjustment range 1–168 h Additional Note Cover plate with infra-red window; Infra-red control, premounted on mounting frame; Power supply unit; Solenoid valve; Fastening material Ordering Information Article no. Colour PU1 116.022.11.1 White alpine 1 116.022.21.1 Gloss chrome 1 116.022.46.1 Matt chrome 1 Additional Note Cover plate with infra-red window; Infra-red control, premounted on mounting frame; Battery box; 2 lithium batteries; Solenoid valve; Fastening material Ordering Information Article no. Colour PU1 116.032.11.1 White alpine 1 116.032.21.1 Gloss chrome 1 116.032.46.1 Matt chrome 1 Product and Installation Guide Washroom & Bathroom 2011 53 Product Guide Duofix urinal frames HyTronic infra-red urinal control, mains powered, Mambo HyTouch hand operated pneumatic urinal control, Mambo 13 13 13 11 13 13 Application Application • For manual flush actuation of urinals • For assembly in installation set • For automatic flush actuation of urinals • For assembly in installation set Characteristics Characteristics • Manual flush actuation • Low flush actuation force • Flush actuation when the actuator button is released • Flush time setting with air nozzles (pneumatic) • Stainless steel actuator plate, with securing bar Product Details Actuation force < 12 N Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Operating pressure 1–8 bar Max. test pressure water 16 bar Max. test pressure air / inert gas 3 bar Operating temperature water max. 30 °C Relative humidity < 100 % Flush time range 4 / 8 / 12 s • Automatic flush actuation, user-controlled • Infra-red detection with background fade-out • Ready for operation after mains connection • Power-failure control system • Flush actuation can be deactivated using HyTronic Clean Handy • Dynamic flushing time adjustment • Stainless steel cover plate, with securing bar Product Details Nominal voltage 110–240 V AC Mains frequency 50–60 Hz Power consumption < 0.5 W Operating voltage 4.5 V DC Protection degree IP 45 Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Additional Note Flush plate; Pneumatic control, pre-mounted on mounting frame; Pneumatic valve; Fastening material Operating pressure 1–8 bar Ordering Information Article no. Colour PU1 116.013.FW.1 Brushed stainless steel 1 Max. test pressure water 16 bar Max. test pressure air / inert gas 3 bar Operating temperature water max. 30 °C Relative humidity < 100 % Flush time factory setting 4s Flush time range 3–15 s Activation time 7s Activation time range 3–15 s Interval flush factory setting 24 h Interval flush adjustment range 1–168 h Additional Note Cover plate with infra-red window; Infra-red control, premounted on mounting frame; Power supply unit; Solenoid valve; Fastening material Ordering Information Article no. Colour 116.023.FW.1 Brushed stainless steel 54 Product and Installation Guide Washroom & Bathroom 2011 PU1 1 Product Guide Duofix urinal frames HyTronic infra-red urinal control, battery powered, Mambo 13 HyTouch hand operated pneumatic urinal control, Tango 13 11 11 13 13 Application • For manual flush actuation of urinals • For assembly in installation set Application • For automatic flush actuation of urinals • For assembly in installation set Characteristics Characteristics • Automatic flush actuation, user-controlled • Infra-red detection with background fade-out • Warning if the battery is low • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Dynamic flushing time adjustment • Stainless steel cover plate, with securing bar Product Details • Manual flush actuation • Low flush actuation force • Flush actuation when the actuator button is released • Flush time setting with air nozzles (pneumatic) • Die-cast zinc actuator plate, with securing bar Product Details Actuation force < 12 N Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Operating voltage 3 V DC Operating pressure 1–8 bar Power consumption < 0.5 W Max. test pressure water 16 bar Protection degree IP 45 Max. test pressure air / inert gas 3 bar Battery type Lithium battery 1.5 V (AA) Operating temperature water max. 30 °C Lifetime lithium battery ~ 2 years Relative humidity < 100 % Lifetime alkaline battery ~ 1.5 years Flush time range 4 / 8 / 12 s Flow rate at 1 bar without flow limiter 0.3 l/s Flow rate at 1 bar with flow limiter 0,24 l/s Operating pressure 1–8 bar Additional Note Flush plate; Pneumatic control, pre-mounted on mounting frame; Pneumatic valve; Fastening material Max. test pressure water 16 bar Max. test pressure air / inert gas 3 bar Ordering Information Operating temperature water max. 30 °C Article no. Colour PU1 Relative humidity < 100 % 116.014.11.1 White alpine 1 Flush time factory setting 4s 116.014.21.1 Gloss chrome 1 Flush time range 3–15 s 116.014.46.1 Matt chrome 1 Activation time 7s Activation time range 3–15 s Interval flush factory setting 24 h Interval flush adjustment range 1–168 h Additional Note Cover plate with infra-red window; Infra-red control, premounted on mounting frame; Battery box; 2 lithium batteries; Solenoid valve; Fastening material Ordering Information Article no. Colour PU1 116.033.FW.1 Brushed Stainless steel 1 Product and Installation Guide Washroom & Bathroom 2011 55 Product Guide Duofix urinal frames HyTronic infra-red urinal control, battery powered, Tango HyTronic infra-red urinal control, mains powered, Tango 13 13 08 13 08 13 Application Application • For automatic flush actuation of urinals • For assembly in installation set • For automatic flush actuation of urinals • For assembly in installation set Characteristics • Automatic flush actuation, user-controlled • Infra-red detection with background fade-out • Ready for operation after mains connection • Power-failure control system • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Dynamic flushing time adjustment • Die-cast zinc cover plate, with securing bar Characteristics • Automatic flush actuation, user-controlled • Infra-red detection with background fade-out • Warning if the battery is low • Setting and interrogation option with HyTronic Service Handy • Flush actuation can be deactivated using HyTronic Clean Handy • Dynamic flushing time adjustment • Die-cast zinc cover plate, with securing bar Product Details Product Details 110–240 V AC Operating voltage 3 V DC Mains frequency 50–60 Hz Power consumption < 0.5 W Power consumption < 0.5 W Protection degree IP 45 4.5 V DC Battery type Lithium battery 1.5 V (AA) Protection degree IP 45 Lifetime lithium battery ~ 2 years Flow rate at 1 bar without flow limiter 0.3 l/s Lifetime alkaline battery ~ 1.5 years Flow rate at 1 bar with flow limiter 0,24 l/s Flow rate at 1 bar without flow limiter 0.3 l/s Operating pressure 1–8 bar Flow rate at 1 bar with flow limiter 0,24 l/s 16 bar Operating pressure 1–8 bar Max. test pressure air / inert gas 3 bar Max. test pressure water 16 bar Operating temperature water max. 30 °C Max. test pressure air / inert gas 3 bar < 100 % Operating temperature water max. 30 °C Flush time factory setting 4s Relative humidity < 100 % Flush time range 3–15 s Flush time factory setting 4s Activation time 7s Flush time range 3–15 s Activation time range 3–15 s Activation time 7s Interval flush factory setting 24 h Activation time range 3–15 s Interval flush adjustment range 1–168 h Interval flush factory setting 24 h Interval flush adjustment range 1–168 h Nominal voltage Operating voltage Max. test pressure water Relative humidity Additional Note Cover plate with infra-red window; Infra-red control, premounted on mounting frame; Power supply unit; Solenoid valve; Fastening material Ordering Information Article no. Colour PU1 116.024.11.1 White alpine 1 116.024.21.1 Gloss chrome 1 116.024.46.1 Matt chrome 1 56 Additional Note Cover plate with infra-red window; Infra-red control, premounted on mounting frame; Battery box; 2 lithium batteries; Solenoid valve; Fastening material Ordering Information Article no. Colour PU1 116.034.11.1 White alpine 1 116.034.21.1 Gloss chrome 1 116.034.46.1 Matt chrome 1 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Accessories Duofix support bracket leg and bracket Accessories Accessories 4 Duofix full height stud 4 47 47 82-130 0 0-20 H 48 73 h Application 5 5 • For installation in split-height PreWall construction in front of a solid or drywall construction • For installation in a partial-height Duofix system wall in front of a solid or drywall construction • For a screed of 0 - 200 mm Application • For creating a load bearing stud wall • For installation in a room-high Duofix system wall • For installing as intermediate or connecting element • For fastening Duofix installation elements and Duofix cross bars • Suitable for installation under sloping roofs up to 50° roof slope Characteristics Characteristics • Element height 820 - 1300 mm • Self-supporting • Support for lateral panelling • Galvanised leg supports, steplessly adjustable 0 - 200 mm • Rotating foot plate, for installation in UW50 and UW75 profiles • Powder-coated, colour Geberit blue • Galvanised • Height-adjustable (telescopic) Product Details Product material Steel Product Details Product material Steel Additional Note 1 rail clip; Fastening bracket; Fastening material Additional Note Rear wall fastening; 2 rail clips; Fastening material Ordering Information Ordering Information Article no. H cm h cm PU1 111.871.00.1 220 - 280 211 1 111.872.00.1 260 - 320 251 1 111.873.00.1 300 - 360 291 1 111.874.00.1 340 - 400 331 1 Article no. PU1 PU2 PU4 111.830.00.1 1 5 50 Duofix system rail 300 5 34 Application • For construction of Duofix PreWall or partition wall • For erecting room-high Duofix system wall Characteristics • Galvanised Additional Note 2 U-rails; Fastening material Ordering Information Article no. PU1 PU4 111.878.00.1 1 80 Product and Installation Guide Washroom & Bathroom 2011 57 Product Guide Accessories Duofix support brackets for large washbasin Duofix support brackets for shallow WC Application • For additional support of WC pans with contact surfaces (x) smaller than 170 mm Application • For fastening washbasins with a fastening distance larger than 380 mm to Duofix frame for washbasin Characteristics X • Fastening distance adjustable 380 - 580 mm • Galvanised • For use with Duofix WC frames Product Details Characteristics Product material Steel • U-profiles, galvanised Additional Note Fastening material Product Details Product material Steel Ordering Information Ordering Information Article no. PU1 Article no. PU1 111.868.00.1 1 111.847.00.1 1 Duofix extension angle brackets Duofix feet-fixing to backwall 13 - 20 Application Application • For alternatively fastening the feet of Duofix elements to the rear wall instead of the floor • For fastening Duofix frames between two studs with a distance of 50 - 65 cm Characteristics Characteristics • Galvanised • Adjustable depth, 130 - 200 mm • Galvanised Product Details Product Details Product material Product material Steel Additional Note Fastening material Ordering Information Article no. PU1 111.867.00.1 1 58 Steel Additional Note Fastening material Ordering Information Article no. PU1 111.869.00.1 1 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Accessories Duofix corner PreWall brackets Duofix PreWall brackets - Universal 13-20 14-20 Application Application • For universal fastening of Duofix installation elements to a solid or drywall construction • For fastening Duofix frames in Duofix system rail • For fastening Duofix frames in front of solid or drywall construction Characteristics Characteristics • Variable angle adaptation for corner installation • Adjustable depth, 140 - 200 mm • Galvanised • Galvanised • Adjustable depth, 130 - 200 mm Product Details Product material Die-cast zinc Additional Note 2 Duofix PreWall brackets for system; 2 rail clips; 2 panelling supports, push-in; Fastening material Ordering Information Article no. PU1 PU2 PU4 111.844.00.1 1 8 384 Additional Note 2 PreWall brackets; 2 M10 threaded rods with long nut; Fastening material Excluded: Panelling supports, push-in Ordering Information Article no. PU1 PU2 PU4 111.835.00.1 1 20 560 Duofix PreWall extension bolts 220 Duofix PreWall brackets with extension set M 10 13-20 Application • For extending Duofix wall anchorings from 200 - 400 mm Product Details Product material Application • For fastening Duofix frames in front of solid or drywall construction • Not suitable for use with Duofix system rail Die-cast zinc Additional Note 2 M10 threaded rods with long nut Ordering Information Characteristics Article no. PU1 PU2 PU4 • Galvanised • Adjustable depth, 130 - 400 mm 111.887.00.1 1 10 2000 Product Details Product material Die-cast zinc Galvanised plasterboard screw Additional Note 2 PreWall brackets; 2 M10 threaded rods with long nut; 2 Duofix PreWall bracket extensions M10 with long nut; 2 panelling supports, push-in; Fastening material Ordering Information Article no. PU1 111.843.00.1 1 Application • For fastening of the panelling and Aqua plasterboard panels to the Duofix support system Characteristics • Self-drilling screws 4.2 x 35 mm Ordering Information Article no. PU2 PU3 PU4 461.030.00.1 200 2000 20000 Product and Installation Guide Washroom & Bathroom 2011 59 Product Guide Accessories Low flush beaker for UP200 Duofix insulating strip 30 m 8 1 Application • To avoid the formation of cracks between Duofix panelling and building structure Characteristics • Single-sided self-adhesive • Permanently elastic • Vinyl foam tape Application • For Geberit concealed cistern UP200 • For reducing flushing volumes to 4.5 l and 3l or 4 l and 2.6 l • Should only be used in conjunction WCs suitable for low flushing volumes Ordering Information Ordering Information Article no. PU1 PU4 111.889.00.1 1 60 Article no. PU1 242.310.00.1 1 Low flush beaker for UP320 HyTronic Service Handy Application • For setting and enquiry of setting values of various electronic Geberit products such as washbasin taps, WC flush actuators, urinal controls and sanitary flushings • For Geberit concealed cistern UP300 and UP320 • For reducing flushing volumes to 4l and 2l flush • Should only be used in conjunction WCs suitable for low flushing volumes Characteristics Ordering Information • 4-line display • Menu guidance • Saving and transfer of settings to other control units of the same type • Compatible with existing control units • Data transmission with infra-red light • Battery-operated Article no. PU1 241.894.00.1 1 Application Monolith wall-hung leg supports Additional Note Pouch; 3 batteries type AAA 1.5 V Ordering Information Article no. PU1 115.860.00.1 1 HyTronic Clean Handy Application • For supporting Geberit wall-hung Monolith sanitary modules on drywall construction and low load bearing walls Ordering Information Application Article no. PU1 • For deactivation of infra-red controlled Geberit flushing valves and flush actuators for sanitary cleaning 131.104.00.1 1 Characteristics • Remote control Additional Note Concise instructions Ordering Information Article no. PU1 PU2 115.831.00.1 1 10 60 Product and Installation Guide Washroom & Bathroom 2011 New Product Guide Accessories Monolith support brackets for shallow wall-hung WC X Ordering Information Article no. 131.105.00.1 Monolith bottom water connection set Application • For use in bottom connections Ordering Information Article no. PU1 131.074.00.1 1 Product and Installation Guide Washroom & Bathroom 2011 61 Product Guide Drainage Drainage Drainage Duofix straight connector d1 d D K Application l • For all drainage pipes • For push-on seal • For WCs with horizontal outlet • For Duofix WC frames L Characteristics • UV-resistant Product Details Product material PE-HD Additional Note Lip seal EPDM; Protection cap Ordering Information Article no. dØ mm d1Ø mm D cm L cm l cm K cm Colour PU1 PU3 PU4 366.887.16.1 90 90 11,2 31 27,5 24 Black 1 40 160 367.887.16.1 110 90 11,2 34,5 31,5 28 Black 1 30 120 Duofix WC S-Bend outlet AD d H di Product Details Product material PVC Additional Note Lip seal EPDM; Sealing collar EPDM; Adhesive PVC-U Ordering Information Article no. dØ mm AD cm H cm Colour PU1 PU2 PU4 388.350.29.1 90 14,5 - 34,5 16,7 Grey 1 10 80 62 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Drainage Duofix 90° bend connector A d1 H K Application d • For all drainage pipes • For WCs with horizontal outlet • For Duofix WC elements Characteristics • UV-resistant Product Details Angle 90° Product material PE-HD Additional Note Lip seal EPDM; Protection cap Ordering Information Article no. dØ mm d1Ø mm A cm angle H cm K cm Colour PU1 PU2 PU4 366.061.16.1 90 90 11 90° 22,5 13 Black 1 10 120 Bend with connector for wall-hung WC A a d1 H Application • For all drainage pipes • For appliances with horizontal outlet K d Characteristics • UV-resistant Product Details Angle 90° Product material PE-HD Additional Note Lip seal EPDM; Protection cap Ordering Information Article no. dØ mm d1Ø mm A cm angle a cm H cm K cm Colour PU1 PU2 PU3 PU4 367.792.16.1 110 110 7,5 90° 4,5 22,5 13 Black 1 5 25 100 Product and Installation Guide Washroom & Bathroom 2011 63 Product Guide Drainage Duofix 45 ° bend connector 45 a L d1 d Application K • For all drainage pipes • For WCs with horizontal outlet • For Duofix WC frames Characteristics • UV-resistant Product Details Angle 45° Product material PE-HD Additional Note Lip seal EPDM; Protection cap Ordering Information Article no. dØ mm d1Ø mm angle a cm L cm K cm Colour PU1 367.945.16.1 110 90 45° 6 8,7 3 Black 1 90 / 110 mm adaptor 75 d1 d2 Application • For all drainage pipes • For connecting 90 mm PE connectors to 110 mm sockets Characteristics • UV-resistant • With stop Product Details Product material PE-HD Additional Note Lip seal EPDM Ordering Information Article no. d1Ø mm d2Ø mm Colour PU1 PU2 PU4 367.928.16.1 90 110 Black 1 10 600 64 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Drainage Duofix manifold connector Z2 Z1 d d Application • For all drainage pipes • For Duofix WC frames when using floats Product Details Product material PVC Additional Note Manifold connector bend; Fin seal; 50 mm length of 110 mm PVC pipe Ordering Information Article no. dØ mm angle ° Z1 cm Z2 cm Colour PU1 PU3 PU4 107.35.05B 110 5° 0,64 6,23 Black 1 12 360 F107.35.09B 110 9° 0,89 6,28 Black 1 24 720 107.35.14B 110 14° 1,09 6,47 Black 1 12 360 F107.35.18B 110 18° 1,13 6,47 Black 1 12 360 107.35.24B 110 24° 1,4 6,95 Black 1 12 360 F107.35.29B 110 29° 1,83 7,73 Black 1 12 360 107.35.34B 110 34° 1,83 7,73 Black 1 12 360 Extended Duofix WC connection set L1 l1 d1 55 d 102±5 l L Application • For Duofix WC frames Product Details Product material PE Additional Note 2 cover caps Ordering Information Article no. dØ mm d1Ø mm L cm L1 cm l cm l1 cm Colour PU1 PU4 152.438.46.1 90 45 26,5 26,5 22 24 Matt chrome 1 164 Product and Installation Guide Washroom & Bathroom 2011 65 Product Guide Drainage Flush pipe extension 1 m s L (m) d d di A cm2 Application • For extension of outlet sleeves • For combination with overflow pipe cone Product Details Product material PE Ordering Information Article no. dØ mm diØ mm s mm A cm² L m Colour PU1 PU2 PU4 152.170.16.1 45 40 2,5 12,6 1 Black 1 5 270 Monolith S-bend for wall-hung WC Application • For connecting wall-hung WC to floor outlet 15 - 30 cm from wall Additional Note S-bend, PVC; WC outlet bend, HDPE, ø 90 mm Ordering Information Article no. Colour PU1 131.088.29.1 Grey 1 Monolith straight pipe for BTW-WC Application • For connecting floor-standing WC to wall outlet 18 cm from wall Additional Note WC outlet pipe, HDPE, ø 90 mm; Adaptor sleeve, HDPE, ø 90/110 mm Ordering Information Article no. Colour PU1 131.083.16.1 Black 1 66 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Traps Monolith drainage connection set for BTW-WC Traps Traps Washbasin trap chrome with 1 1/4" BSP waste connection and 32 mm outlet Application Application • For connecting floor-standing WC to floor outlet 7 - 15 cm from wall • For washbasin Additional Note WC outlet bend, HDPE, ø 90 mm; Adaptor sleeve, HDPE, ø 90/110 mm; Rubber seal EPDM; Fastening material Characteristics Ordering Information Article no. Colour PU1 131.082.16.1 Black 1 Monolith offset outlet pipe for wall mounted WC • Water seal with partition wall • Corrosion-resistant • Plug connection on the outlet pipe • With 32 mm / 1 1/4" waste adaptor Product Details Depth of water seal 75 mm Drainage capacity 0.7 l/s Ordering Information Article no. Colour PU1 151.039.21.1 Gloss chrome 1 Application • For connecting wall-hung WC to wall outlet 17 - 19 cm Additional Note Straight connector for WC, 7 cm offset, PP, 90 mm; 2 sealing collars Ordering Information Article no. PU1 131.108.11.1 1 Monolith step pipe for wall-hung WC Application • For connecting wall-hung WC to wall outlet 21-23 cm Additional Note WC outlet pipe, 3 cm offset, HDPE, ø 90 mm Ordering Information Article no. Colour PU1 131.085.11.1 White alpine 1 Product and Installation Guide Washroom & Bathroom 2011 67 Product Guide Traps Bath trap, overflow and chrome pop-up waste standard 40 Bath trap, overflow and chrome pop-up waste large 43 40 43 100 180 100 180 180 92 120 40 160-300 50 180 Characteristics 92 • Without contraflow principle • Bathtub outlet and overflow assembly • Water seal • Pop-up operation • Outlet connection can be rotated as needed • With 40 mm / 1 1/2" waste adaptor Characteristics Additional Note Trap; Cable actuator; Overflow; Outlet bend; Adaptor; Fastening material; Outlet cover Ordering Information Article no. Colour PU1 PU2 150.535.21.1 Gloss chrome 1 10 68 120 40 160-300 50 • Without contraflow principle • Bathtub outlet and overflow assembly • Water seal • Pop-up operation • Outlet connection can be rotated as needed • With 40 mm / 1 1/2" waste adaptor Additional Note Trap; Cable actuator; Overflow; T-piece; Outlet bend; Adaptor; Fastening material; Outlet cover Ordering Information Article no. Colour PU1 PU2 150.536.21.1 Gloss chrome 1 8 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Traps Bath trap, overflow and filler, chrome pop-up waste standard 40 Bath trap, overflow and filler, chrome pop-up waste large 43 40 43 100 100 180 180 3/4"/ 16 3/4"/ 16 180 92 120 40 160-300 50 180 92 Characteristics • Bathtub drain, overflow and inlet set • Water seal • Pop-up operation • Outlet connection can be rotated as needed • Direction of inlet jet flexible • Water supply connection bracket can be rotated • Water supply connection bracket suitable for Mepla pipes • Without contraflow principle • With 40 mm / 1 1/2" waste adaptor Additional Note Trap; Cable actuator; Overflow; Water inlet; Water supply connection bracket; Outlet bend; Adaptor; Fastening material; Outlet cover Ordering Information Article no. Colour PU1 PU2 150.712.21.1 Gloss chrome 1 12 120 40 160-300 50 Characteristics • Bathtub drain, overflow and inlet set • Water seal • Pop-up operation • Outlet connection can be rotated as needed • Direction of inlet jet flexible • Water supply connection bracket can be rotated • Water supply connection bracket suitable for Mepla pipes • Without contraflow principle • With 40 mm / 1 1/2" waste adaptor Additional Note Trap; Cable actuator; Overflow; Water inlet; T-piece; Water supply connection bracket; Outlet bend; Adaptor; Fastening material; Outlet cover Ordering Information Article no. Colour PU1 PU2 150.713.21.1 Gloss chrome 1 12 Product and Installation Guide Washroom & Bathroom 2011 69 Product Guide Traps PushControl bath trap, overflow and chrome pop-up waste, standard PushControl bath trap, overflow and chrome pop-up waste, long 45 145-26 45 24-50 23-46 23-46 40 40 43 43 9 59 8 14 9 59 8 10 14 10 Application Application • For bathtubs with valve hole ø 52 mm • For bathtubs in standard size • To fit most european bath tubs • For bathtubs with valve hole ø 52 mm • For installation in bathtubs with special lengths • To fit most european bath tubs Characteristics Characteristics • Bathtub drain with push button actuation virtually flush with the tub • Construction height trap 90 mm • Odour trap 270° swivelling • Drain valve made from stainless steel • With 40 mm / 1 1/2" waste adaptor • Bathtub drain with push button actuation virtually flush with the tub • Construction height trap 90 mm • Odour trap 270° swivelling • Drain valve made from stainless steel • With 40 mm / 1 1/2" waste adaptor Product Details Product Details Drainage capacity 1 l/s Drainage capacity Overflow capacity 0.65 l/s Overflow capacity 1 l/s 0.65 l/s Depth of water seal 50 mm Depth of water seal 50 mm Additional Note Drain valve; Trap; Overflow; Cable actuator; Ready-to-fit set; Outlet pipe Additional Note Drain valve; Trap; Overflow; Cable actuator; Ready-to-fit set; Outlet pipe Ordering Information Ordering Information Article no. Colour PU1 PU2 PU4 Article no. Colour PU1 PU2 PU4 150.770.11.1 White alpine 1 10 80 150.771.11.1 White alpine 1 10 80 150.770.21.1 Gloss chrome 1 10 80 150.771.21.1 Gloss chrome 1 10 80 70 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Traps PushControl bath trap, overflow and chrome pop-up waste, high Shower tray trap and waste 90 mm 115 45 15-28 ø 90 ø43 ø40 0 2 - 25 8 43 92 Application 44-60 • For shower trays with valve hole ø 90 mm • For shower trays without overflow 40 43 Characteristics 9 59 8 14 • Dip tube and dip tube support can be dismantled • Construction height 80 mm • With 40 mm / 1 1/2" waste adaptor 10 Application Product Details • For bathtubs with valve hole ø 52 mm • For installation in bathtubs with special heights • To fit most european bath tubs Characteristics • Bathtub drain with push button actuation virtually flush with the tub • Construction height trap 90 mm • Odour trap 270° swivelling • Drain valve made from stainless steel • With 40 mm / 1 1/2" waste adaptor Depth of water seal 50 mm Drainage capacity with 15 mm head of water 0.5 l/s Additional Note Trap; Screw connection ø 40 mm; Outlet bend; Adaptor; Fastening material; Outlet cover Ordering Information Article no. Colour PU1 150.679.21.1 Gloss chrome 1 Product Details Drainage capacity 1 l/s Overflow capacity 0.65 l/s Depth of water seal 50 mm Shower tray trap and waste 50 mm 8 Additional Note Drain valve; Trap; Overflow; Cable actuator; Ready-to-fit set; Outlet pipe 47 ø43 ø40 03-15 Ordering Information Article no. Colour PU1 PU2 PU4 150.772.11.1 White alpine 1 10 80 150.772.21.1 Gloss chrome 1 10 80 85 47 85 Application • For shower trays with valve hole ø 52 mm • For shower trays without overflow Extended connection set for thicker baths Characteristics • Dip tube and dip tube support can be dismantled • Construction height 85 mm • With 40 mm / 1 1/2" waste adaptor 27 Product Details Application Drainage capacity 0.65 l/s Depth of water seal 50 mm • For acrylic bathtubs with overflow Additional Note Drain valve seat extension with O-ring; Banjo bolt; Adjusting screw Additional Note Trap; Outlet bend; Adaptor; Outlet cover Ordering Information Ordering Information Article no. PU1 150.247.00.1 1 Article no. dØ Colour PU1 PU2 150.688.21.1 40 Gloss chrome 1 10 Product and Installation Guide Washroom & Bathroom 2011 71 Product Guide Traps Duofix shower element H50 Duofix shower element H130 50 New 50 11 24 100 100 55 41 77 9 9–20 130 73 48 11 24 24 0 77 55 55 24 45° 16 9 9–20 0 73 65 355 355 8 Application 48 11 24 55 24 45° 16 65 355 355 • For use within buildings • For drainage of wet room installations • For use with composite seals • For installation in a partial-height Duofix system wall in front of a solid or drywall construction • For installation in a room-high Duofix system wall Characteristics 8 Application • For use within buildings • For drainage of wet room installations • For use with composite seals • For installation in a half-height Duofix system wall in front of a solid or drywall construction • For installation in a room-high Duofix system wall Characteristics • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Floor construction maximum 20 cm • Minimum height of screed 90 mm • Panelling thickness 10–25 mm, sealing level can be adjusted up to 15 mm • Possible tile build-up 6–26 mm • Height-adjustable element • Mounting plate (wood) for surface-mounted and concealed taps, height- and depth-adjustable • Mounting plate (metal) for surface-mounted taps, height-adjustable • Sealing level for sealing connection that is free of tension • Outlet body with drainage capacity of 0.85 l/s • Trap insert can be removed for cleaning • Drainage connection left, right or front centre • Speak to us about our partnership with wet room floor specialists • Self-supporting • Frame with C profile 40/40 mm • Powder-coated frame, ultramarine blue • Feet can be retracted 5 cm • Rotating foot plate, for installation in UW50 and UW75 profiles • Floor construction maximum 20 cm • Minimum height of screed 90 mm • Panelling thickness 10–25 mm, sealing level can be adjusted up to 15 mm • Possible tile build-up 6–26 mm • Height-adjustable element • Sealing level for sealing connection that is free of tension • Outlet body with drainage capacity of 0.85 l/s • Trap insert can be removed for cleaning • Drainage connection left, right or front centre • Speak to us about our partnership with wet room floor specialists Product Details Depth of water seal 50 mm Additional Note Fastening material; Bidet outlet bend, HDPE, ø 50 mm; Outlet bend HDPE ø 50 mm for front connection Excluded: Ready-to-fit set for shower element Ordering Information Article no. PU1 111.743.00.1 1 Additional Note Fastening material; Bidet outlet bend, HDPE, ø 50 mm; Outlet bend HDPE ø 50 mm for front connection Excluded: Ready-to-fit set for shower element; Tap connections Ordering Information Article no. PU1 111.731.00.1 1 72 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Traps Ready-to-fit set for Duofix shower element, stainless steel Ready-to-fit set for Duofix shower element, gloss chrome Application Application • For use with Geberit Duofix shower element • For use with Geberit Duofix shower element Characteristics Characteristics • Can be removed for cleaning • Plastic sight frame, mother-of-pearl silver • Brushed stainless steel cover • Can be removed for cleaning • Plastic sight frame, mother-of-pearl silver • Plastic cover, gloss chrome Additional Note Sight frame; Cover; Hair trap Additional Note Sight frame; Cover; Hair trap Ordering Information Article no. Ordering Information Colour 154.330.FW.1 Brushed stainless steel PU1 PU2 Article no. Colour PU1 PU2 1 21 154.330.21.1 Gloss chrome 1 21 Ready-to-fit set for Duofix shower element, white Ready-to-fit set for Duofix shower element, bespoke Application Application • For use with Geberit Duofix shower element • For use with Geberit Duofix shower element Characteristics Characteristics • Can be removed for cleaning • Plastic sight frame, mother-of-pearl silver • Plastic cover, white alpine • Can be removed for cleaning • Plastic sight frame, black • For customers to install a bespoke finish with a thickness of 6 mm 26 mm Additional Note Sight frame; Cover; Hair trap Additional Note Sight frame; Cover; Hair trap Ordering Information Article no. Colour PU1 PU2 154.330.11.1 White alpine 1 21 Ordering Information Article no. PU1 PU2 154.330.00.1 1 21 Product and Installation Guide Washroom & Bathroom 2011 73 Product Guide Traps Design grating - architectural, squares Uniflex drain for flat showers 30 10 ø43 ø40 1-11 Application 85 59 • For the drainage of a wet room installation 145 Characteristics Application • Without screw connection • For the drainage of a wet room installation • For use with composite seals • For use within buildings Product Details Product material Characteristics • Minimal construction height 95 mm and maximum 195 mm • Grating made of stainless steel • Sealing collar, fleece-laminated 500 x 500 mm • Vernier adjustment of grating in height, inclination and off-set possible via compensating ring • With 40 mm / 1 1/2" waste adaptor Stainless steel Ordering Information Article no. PU1 154.301.00.1 1 Design grating - architectural, radial Product Details Drainage capacity min. 0.45 l/s Drainage capacity max. 0.74 l/s Depth of water seal 50 mm Additional Note Trap; Adaptor; Thin bed top piece; Grating; Rubber collar; Compensating ring; Hair trap; Seal set for use with PVC ; Protection housing; Installation aid Application • For the drainage of a wet room installation Characteristics Ordering Information Article no. PU1 154.005.00.1 1 • Without screw connection Product Details Product material Stainless steel Ordering Information Standard grating screwable 91 Article no. PU1 154.302.00.1 1 49 Design grating - trendy 91 Application • For Uniflex Outlet for floor even showers Application Characteristics • For the drainage of a wet room installation • Can be locked with screws • Grating and screws made of stainless steel Characteristics • Without screw connection Product Details Product material Stainless steel Product Details Product material Stainless steel Additional Note Screws Ordering Information Ordering Information Article no. PU1 154.303.00.1 1 Article no. PU1 154.300.00.1 1 74 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Traps Uniflex shower channel, floor Design grating - classic, natural l 15 6 14 50 Application l1 • For the drainage of a wet room installation Characteristics 112-176 52 14 193 l2 l3 12-26 10-15 • Without screw connection Application Product Details Product material Stainless steel Ordering Information Article no. PU1 154.304.00.1 1 • For use within buildings • For the drainage of a wet room installation • For use with composite seals • For installing in the room centre Characteristics • Minimal construction height 112 mm • Drainpipe and grating frame made of stainless steel • Height-adjustable • Insulation of material noise • Stress elimination to prevent cracking of ceramic plates • Vernier adjustment of grating in height, inclination and off-set possible via compensating ring • Outlet bend ø 50 mm Design grating - puristic, square Product Details Application • For the drainage of a wet room installation Characteristics • Without screw connection Product Details Product material Stainless steel Drainage capacity 0.8 l/s Depth of water seal 50 mm Additional Note 2 odour traps, incl. dip tube; Outlet bend; Drainpipe with the installation flange for thin mortar installation; Frame of grating; Rubber collar; 4 feet, incl. acoustic insulation elements; Protection housing; Adhesive; Fastening material; Excludes ready to fit set Ordering Information Ordering Information Article no. PU1 Article no. l1 cm l2 cm l3 cm PU4 1 l cm PU1 154.305.00.1 154.100.00.1 70 33 13,7 80 1 20 154.101.00.1 80 38 18,7 90 1 20 154.102.00.1 90 43 23,7 100 1 20 154.103.00.1 100 48 28,7 110 1 20 154.130.00.1 110 53 33,7 120 1 154.131.00.1 120 58 38,7 130 1 Design grating - puristic, circle Application • For the drainage of a wet room installation Characteristics • Without screw connection Product Details Product material Stainless steel Ordering Information Article no. PU1 154.306.00.1 1 Product and Installation Guide Washroom & Bathroom 2011 75 Product Guide Traps Ready-to-fit set shower channel, brushed stainless steel Uniflex shower channel, wall l 3 6 L 135 50 l1 14 52 193 l2 l3 12-26 112-176 5 14 6 Application • For use with Uniflex shower channel 10-15 Characteristics Application • Brushed stainless steel • For use within buildings • For the drainage of a wet room installation • For use with composite seals • For wall mounting Additional Note Design cover; 10 damping caps; Extraction tool Ordering Information Characteristics • Minimal construction height 112 mm • Drainpipe and grating frame made of stainless steel • Height-adjustable • Insulation of material noise • Stress elimination to prevent cracking of ceramic plates • Vernier adjustment of grating in height, inclination and off-set possible via compensating ring • Outlet bend ø 50 mm Article no. L cm PU1 PU4 154.350.00.1 70 1 40 154.351.00.1 80 1 40 154.352.00.1 90 1 26 154.353.00.1 100 1 26 154.354.00.1 110 1 154.355.00.1 120 1 Product Details Drainage capacity 0.8 l/s Depth of water seal 50 mm Ready-to-fit set shower channel, bespoke Additional Note 2 odour traps, incl. dip tube; Outlet bend; Drainpipe with the installation flange for thin mortar installation; Frame of grating; Rubber collar; 4 feet, incl. acoustic insulation elements; Margin insulation tape for decoupling solid-borne sound; Protection housing; Adhesive; Fastening material; Excludes ready to fit set Application Ordering Information • For use with Uniflex shower channel Article no. l cm l1 cm l2 cm l3 cm PU1 PU4 154.105.00.1 70 33 13,7 80 1 20 154.106.00.1 80 38 18,7 90 1 20 154.107.00.1 90 43 23,7 100 1 20 154.108.00.1 100 48 28,7 110 1 20 154.135.00.1 110 53 33,7 120 1 154.136.00.1 120 58 38,7 130 1 Ready-to-fit set shower channel, creative set Application • For use with bespoke Uniflex shower channel ready-to-fit set Characteristics • Lid can be covered with ceramic plates • Requires 154.299.00.1 Additional Note Design cover; Extraction tool Ordering Information Article no. L cm PU1 154.360.00.1 70 1 154.361.00.1 80 1 154.362.00.1 90 1 154.363.00.1 100 1 154.356.00.1 110 1 154.357.00.1 120 1 Characteristics • Production and care instructions for the manufacture of individual design covers Additional Note Extraction tool; 10 damping caps (8.5 mm); 10 damping caps (14.5 mm) Ordering Information Article no. PU1 154.299.00.1 1 76 Product and Installation Guide Washroom & Bathroom 2011 PU4 20 Product Guide Fill and flush valves for ceramic cisterns Impuls360 bottom filling valve Fill and flush valves for ceramic cisterns Fill and flush valves for ceramic cisterns 96 92 Impuls380 side filling valve 25 CL 71 WL CL 112 61 3 WL 235 - 385 146 - 296 243 212 9 - 15 41.5 G Application Application • For filling cisterns • For use with grey water (rainwater), providing a filter system is used • For use with sea water (brass parts must be dezincification-resistant) • For use with clean drinking water • Can be installed in an exposed cistern • Not suitable for use with water with an elevated chlorine content (swimming pools, etc.) • Not suitable for use with cleaning agents, disinfectants and colouring agents put into the cistern (contact Geberit if in doubt) • For water supply connection at the bottom • For water supply connection 1/2" Characteristics • Height-adjustable Product Details Operating temperature water max. 25 °C Flow pressure range 0.1–10 bar Flow rate at 3 bar 0.16 l/s Line noise at 3 bar 17 dB(A) Additional Note Seal; Nut Characteristics • The filling height can be set by turning the spindle • The valve opens after the water level drops by 20 mm Ordering Information Product Details Flow pressure range 0.1–10 bar Flow rate at 0.5 bar 0.07 l/s Flow rate at 3 bar 0.19 l/s Line noise at 3 bar 12 dB(A) Line noise at 5 bar 18 dB(A) Pressure shock increase at 6 bar +1 bar Max. temperature during storage 40 °C Operating temperature water max. 25 °C Article no. PU1 PU2 PU4 281.206.00.1 1 25 600 Impuls260 dual flush valve with "half moon" buttons for ceramic cisterns 38-45 125 8 Additional Note Adaptor; Cone screw fitting; Spacer 325-41 185-28 Ordering Information Article no. PU1 PU2 PU4 240.700.00.1 1 10 200 min. 9 mm max. 35 mm Application • For installation in ceramic cisterns Characteristics • Overflow pipe height-adjustable • Adjustable flush volume depending on amount of water in cistern • Dual flush actuator with threaded rod for fastening the cistern cover Product Details Actuation force 18 N Max. temperature during storage 40 °C Operating temperature water max. 25 °C Flush volume large range 6/9l Flush volume small range 3–4 l Additional Note Dual flush unit; Lid attachment; Dual flush actuator; Fastening material; Seals Excluded: Fill valve Ordering Information Article no. PU1 PU2 PU4 261.157.00.1 1 36 432 Product and Installation Guide Washroom & Bathroom 2011 77 Product Guide Fill and flush valves for ceramic cisterns Impuls280 dual flush valve with round chrome and blue square flush buttons for ceramic cisterns 38-45 16 12-45 min. 08 max. 15 8 312-45 293-431 17-27 min. 09 max. 2 Application • For installation in ceramic cisterns Characteristics • Overflow pipe height-adjustable • Adjustable flush volume depending on amount of water in cistern • Dual flush actuator with threaded rod for fastening the cistern cover Product Details Flush volume large range 6/9l Flush volume small range 3–4 l Actuation force 18 N Flow pressure range 0.1–10 bar Operating temperature water max. 25 °C Max. temperature during storage 40 °C Additional Note Dual flush unit; Dual flush actuator with rosette; Fastening material; Rosette ø 50 mm Ordering Information Article no. Colour 282.350.KD.1 Gloss chrome / blue 78 PU1 PU2 PU4 1 18 108 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Geberit AquaClean Product Details Geberit AquaClean Geberit AquaClean Nominal voltage Geberit AquaClean 8000plus wall mounted WC 42 25 230 V AC Mains frequency 50–60 Hz Power consumption 1000 W Power consumption standby / with heating switched on 1 / 9 W Protection degree 43 18−20 135 415−455 21−25 5−9 615 290 215 IP x4 Protection class I Length of mains connection cable 70 cm Air volume flow rate odour extraction unit 10 m3/h Air volume flow rate dryer 12 m3/h Flow rate, anal shower 2.1–5.5 l/min Flow rate, Lady shower 1.4–3 l/min Dryer temperature factory setting 45 °C Dryer temperature range 20–45 °C Water temperature factory setting 37 °C Water temperature range 10–39 °C Storage temperature -10 – +60 °C Operating temperature 10–40 °C Application Spray time factory setting 20 s • For gentle cleaning with water • For mains fed water connection • Complete solution for concealed cistern Number of shower pressure settings, shower spray 7 Flow pressure range 1–10 bar Storage water heater capacity 2.0 l Net weight 32 kg Characteristics Gross weight 37 kg • Warm water wash with adjustable temperature • Warm air dryer with adjustable temperature • Washdown WC with surface-coated ceramic appliance • WC seat with soft closing lid • Infra-red user detection • Odour extraction • Shower arm can be set to 7 positions • Oscillating spray (automatic forward and reverse motion of the spray arm) • Pulsating spray • Adjustable spray intensity • Automatic pre-rinsing of spray nozzle with fresh water and postrinsing with nozzle cleaner for Geberit AquaClean 8000plus • Integrated storage water heater tank with ON/OFF and economy setting • 4 programmable user profiles • Water supply connection on the left side • Mains fed water connection required • Functions and settings adjustable via remote control Maximum load WC seat / WC lid 150 kg Additional Note Includes: Remote control with LC display, wall-mounted holder and batteries, LR03 (AAA); Cover plate for remote control compartment; Active carbon filter; Nozzle cleaner for Geberit AquaClean 8000plus; Water supply connection set for UP300 / UP320 concealed cistern; Dryer fan with housing; Acoustic insulation set; Fastening material; Spray shield Ordering Information Article no. Colour PU1 PU4 180.101.11.1 White alpine 1 4 Using the supplied standard water connection set, all concealed cisterns (except for UP200 and UP720) can be connected with the prepared conduit pipe. The UP200 concealed cistern additionally requires the reinforced braided hose with T-piece (art. no. 241.819.00.1) to be ordered. The UP720 concealed cistern additionally requires the connection hose 242.413.00.1 to be ordered. Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. Product and Installation Guide Washroom & Bathroom 2011 79 Product Guide Geberit AquaClean Geberit AquaClean 8000 wall mounted WC 42 25 205 43 18−20 135 415−455 21−25 Using the supplied standard water connection set, all concealed cisterns (except for UP200 and UP720) can be connected with the prepared conduit pipe. The UP200 concealed cistern additionally requires the reinforced braided hose with T-piece (art. no. 241.819.00.1) to be ordered. The UP720 concealed cistern additionally requires the connection hose 242.413.00.1 to be ordered. 5−9 615 290 215 Application • For gentle cleaning with water • For mains fed water connection • Complete solution for concealed cistern Characteristics • Warm water wash with adjustable temperature • Washdown WC with surface-coated ceramic appliance • Infra-red user detection • WC seat with soft closing lid • Integrated storage water heater tank with ON/OFF and economy setting • Oscillating spray (automatic forward and reverse motion of the spray arm) • Adjustable spray intensity • Automatic pre- and post-rinsing of the spray nozzle with fresh water • Water supply connection on the left side • Mains fed water connection required Product Details Nominal voltage 230 V AC Mains frequency 50–60 Hz Power consumption 1000 W Power consumption standby / with heating switched on 1 / 9 W Protection degree IP x4 Protection class I Length of mains connection cable 70 cm Flow rate, anal shower 2.1–5.5 l/min Water temperature factory setting 37 °C Storage temperature -10 – +60 °C Operating temperature 10–40 °C Spray time factory setting 20 s Number of shower pressure settings, shower spray 7 Flow pressure range 1–10 bar Storage water heater capacity 2.0 l Net weight 27.5 kg Gross weight 34 kg Maximum load WC seat / WC lid 150 kg Additional Note Water supply connection set for UP300 / UP320 concealed cistern; Acoustic insulation set; Fastening material; Spray shield Ordering Information Article no. Colour PU1 PU4 146.181.11.1 White alpine 1 6 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. 80 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Geberit AquaClean Geberit AquaClean 5000plus New Product Details Nominal voltage 485 155 185 25 295 4-8 195 30 R3/8 22 5 385 225 13-165 850 W Protection degree 35 30 50–60 Hz Power consumption Power consumption standby / with heating switched on 0.9 / 6.7 W 55 15 35 230 V AC Mains frequency 29 11 507 Application • For gentle cleaning with water • For subsequent mounting on a WC ceramic (replaces WC seat and lid) • For mains fed water connection Characteristics • Warm water wash • WC seat with soft closing lid • Infra-red user detection • Odour extraction • Shower arm can be set to 7 positions • Oscillating spray (automatic forward and reverse motion of the spray arm) • Pulsating spray • Adjustable spray intensity • Integrated storage water heater tank with ON/OFF and economy setting • Warm air dryer with adjustable temperature • Mains connection cable can be cut to length • Mains power connection at rear with hidden pipe-laying option to the left or right • Functions and settings adjustable via remote control • Automatic pre- and post-rinsing of the spray nozzle with fresh water • Water supply connection on the left side IP x4 Protection class I Length of mains connection cable 2m Air volume flow rate odour extraction unit 4.4 m3/h Air volume flow rate dryer 9.1 m3/h Flow rate, anal shower 1.7–3 l/min Flow rate, Lady shower 0.6–2 l/min Dryer temperature factory setting 45 °C Dryer temperature range 20–45 °C Water temperature factory setting 37 °C Water temperature range 10–39 °C Storage temperature -10 – +60 °C Operating temperature 10–40 °C Spray time factory setting 20 s Number of shower pressure settings, shower spray 7 Flow pressure range 1–10 bar Storage water heater capacity 1.65 l Net weight 6.3 kg Gross weight 9.2 kg Maximum load WC seat / WC lid 150 kg Additional Note Includes: Remote control with LC display, wall-mounted holder and batteries, LR03 (AAA); Active carbon filter; Water supply connection set for left side connection; Spray nozzle (replacement); Fastening material; Compensation pad for toilet seat; Spray shield Ordering Information Article no. Colour PU1 PU4 146.114.11.1 White alpine 1 12 For installation with UP200 concealed cistern, order: • Article no. 240.634.00.1 for UP200 concealed cistern H82 • Article no. 240.635.00.1 for UP200 concealed cistern H98 For installation with the UP300 and UP320 concealed cistern, order: • Article no. 249.801.00.1 For installation with the UP720 concealed cistern, order: • Article no. 242.413.00.1 and 249.801.00.1 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. Product and Installation Guide Washroom & Bathroom 2011 81 Product Guide Geberit AquaClean Geberit AquaClean 5000 New 155 485 185 Ordering Information 55 15 35 35 25 30 295 4-8 195 5 385 225 13-165 Article no. Colour PU1 PU4 146.122.11.1 White alpine 1 12 R3/8 22 30 Additional Note Includes: Active carbon filter; Water supply connection set for left side connection; Spray nozzle (replacement); Fastening material; Compensation pad for toilet seat; Spray shield For installation with UP200 concealed cistern, order: • Article no. 240.634.00.1 for UP200 concealed cistern H82 • Article no. 240.635.00.1 for UP200 concealed cistern H98 For installation with the UP300 and UP320 concealed cistern, order: • Article no. 249.801.00.1 For installation with the UP720 concealed cistern, order: • Article no. 242.413.00.1 and 249.801.00.1 29 11 507 Application • For gentle cleaning with water • For subsequent mounting on a WC ceramic (replaces WC seat and lid) • For mains fed water connection Characteristics • Warm water wash with adjustable temperature • WC seat with soft closing lid • Infra-red user detection • Odour extraction • Spray arm with nozzle for anal area, can be extended • Oscillating spray (automatic forward and reverse motion of the spray arm) • Adjustable spray intensity • Integrated storage water heater tank with ON/OFF setting • Mains power connection at rear with hidden pipe-laying option to the left or right • Mains connection cable can be cut to length • Automatic pre- and post-rinsing of the spray nozzle with fresh water • Water supply connection on the left side • Mains fed water connection required Product Details Nominal voltage 230 V AC Mains frequency 50–60 Hz Power consumption 850 W Power consumption standby / with heating switched on 0.9 / 6.7 W Protection degree IP x4 Protection class I Length of mains connection cable 2m Air volume flow rate odour extraction unit Flow rate, anal shower 4.4 m3/h 1.7–3 l/min Water temperature factory setting 37 °C Storage temperature -10 – +60 °C Operating temperature 10–40 °C Spray time factory setting 20 s Number of shower pressure settings, shower spray 7 Flow pressure range 1–10 bar Storage water heater capacity 1.65 l Net weight 6.1 kg Gross weight 9 kg Maximum load WC seat / WC lid 150 kg 82 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. Product and Installation Guide Washroom & Bathroom 2011 Product Guide Geberit AquaClean Geberit AquaClean 4000 New 40 145 15 155 R1/2 55 15 3 55 4 17 30 285 5-9 30 Ordering Information Article no. Colour PU1 PU4 146.132.11.1 White alpine 1 12 For installation with UP200 concealed cistern, order: • Article no. 240.634.00.1 for UP200 concealed cistern H82 • Article no. 240.635.00.1 for UP200 concealed cistern H98 For installation with the UP300 and UP320 concealed cistern, order: • Article no. 249.801.00.1 For installation with the UP720 concealed cistern, order: • Article no. 242.413.00.1 and 249.801.00.1 5 14 225 13-165 26 10 505 Application • For gentle cleaning with water • For subsequent mounting on a WC ceramic (replaces WC seat and lid) • For mains fed water connection Characteristics • Warm water wash • WC seat with soft closing lid • Spray intensity can be set to 5 different levels • Mains power connection at rear with hidden pipe-laying option to the left or right • Automatic pre- and post-rinsing of the spray nozzle with fresh water • Integrated storage water heater tank with ON/OFF setting • Water supply connection on the left side Product Details Nominal voltage 230 V AC Mains frequency 50–60 Hz Power consumption 800 W Power consumption standby / with heating switched on 0.9 / 5.8 W Protection degree IP x4 Protection class I Length of mains connection cable 2m Flow rate, anal shower 0.9–1.6 l/min Water temperature factory setting 37 °C Operating temperature 10–40 °C Storage temperature -10 – +60 °C Spray time factory setting 20 s Number of shower pressure settings, shower spray 5 Flow pressure range 0.5–10 bar Storage water heater capacity 0.9 l Net weight 4.1 kg Gross weight 7.5 kg Maximum load WC seat / WC lid 150 kg Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. Product and Installation Guide Washroom & Bathroom 2011 83 Product Guide Geberit AquaClean Geberit AquaClean Design Panel for 8000plus & 8000 475 New Geberit AquaClean Design Panel for 8000plus & 8000, glass 2 475 15 162 95 New 162 95 107 107 58 58 65-70 65–70 106 10 106 10 48 18 48 18 Application Application • For retrofitting Geberit AquaClean complete solutions to a Geberit concealed cistern, without conduit pipe • For use with Geberit UP300 and UP320 concealed cistern • For use with Geberit Twinline concealed cistern 12 cm (UP130) (model 110.8xx from year of manufacture 1997, and from year of manufacture 1988 with built-in conversion set for dual flush; Geberit actuator plates Highline, Twinline, 200F) • For use on fully tiled surface • For retrofitting Geberit AquaClean complete solutions to a Geberit concealed cistern, without conduit pipe • For use with Geberit UP300 and UP320 concealed cistern • For use with Geberit Twinline concealed cistern 12 cm (UP130) (model 110.8xx from year of manufacture 1997, and from year of manufacture 1988 with built-in conversion set for dual flush; Geberit actuator plates Highline, Twinline, 200F) • For use on fully tiled surface Characteristics Characteristics • Suitable for distance of 65-70 cm, measured from the middle of the actuator plate to the middle of the ceramic fastening • Retrofit set can be mounted and removed without damaging the tile surface • Design Panel with integrated actuation for dual flush • Surface even actuation • Hidden water supply connection • Cable for power connection can be housed in Design Panel • High pressure laminate • Suitable for distance of 65-70 cm, measured from the middle of the actuator plate to the middle of the ceramic fastening • Retrofit set can be mounted and removed without damaging the tile surface • Design Panel with integrated actuation for dual flush • Surface even actuation • Hidden water supply connection • Cable for power connection can be housed in Design Panel Additional Note Design Panel; Reinforced braided hose; Y-branch; 4 actuator rods; Tpiece; Fastening material Ordering Information Additional Note Design Panel; Reinforced braided hose; Y-branch; 4 actuator rods; Tpiece; Fastening material Ordering Information PU1 PU4 Article no. Colour PU1 Article no. 115.325.SG.1 Black Colour 1 10 115.323.11.1 White 1 115.325.SF.1 1 10 White Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. 84 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Geberit AquaClean Geberit AquaClean Design Panel for 4000, 5000 & 5000plus 38 New Geberit AquaClean Design Panel for 4000, 5000 & 5000plus, glass 2 38 15 162 107 New 162 95 495 95 107 59 495 59 Application Application • For retrofitting Geberit AquaClean complete solutions to a Geberit concealed cistern, without conduit pipe • For use with Geberit UP300 and UP320 concealed cistern • For use with Geberit Twinline concealed cistern 12 cm (UP130) (model 110.8xx from year of manufacture 1997, and from year of manufacture 1988 with built-in conversion set for dual flush; Geberit actuator plates Highline, Twinline, 200F) • For use on fully tiled surface • For retrofitting Geberit AquaClean complete solutions to a Geberit concealed cistern, without conduit pipe • For use with Geberit UP300 and UP320 concealed cistern • For use with Geberit Twinline concealed cistern 12 cm (UP130) (model 110.8xx from year of manufacture 1997, and from year of manufacture 1988 with built-in conversion set for dual flush; Geberit actuator plates Highline, Twinline, 200F) • For use on fully tiled surface Characteristics Characteristics • Retrofit set can be mounted and removed without damaging the tile surface • Design Panel with integrated actuation for dual flush • Surface even actuation • Water supply connection hidden in design panel • High pressure laminate • Retrofit set can be mounted and removed without damaging the tile surface • Design Panel with integrated actuation for dual flush • Surface even actuation • Water supply connection hidden in design panel Additional Note Design Panel; Reinforced braided hose; Y-branch; 4 actuator rods; Tpiece; Fastening material Additional Note Design Panel; Reinforced braided hose; Y-branch; 4 actuator rods; Tpiece; Fastening material Ordering Information Ordering Information PU1 PU4 Article no. Colour PU1 115.324.SG.1 Black Article no. Colour 1 10 115.322.11.1 White 1 115.324.SF.1 1 10 White Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. Product and Installation Guide Washroom & Bathroom 2011 85 Product Guide Geberit AquaClean Geberit AquaClean connection sets Geberit AquaClean 8000plus & 8000 braided hose for installation with UP200 cistern Geberit AquaClean 4000, 5000 & 5000plus water supply connection set for UP300 / UP320/ UP720/ Duofix WC frame 1.12 m New Application • For UP200 concealed cistern with top/front actuation • For connecting Geberit AquaClean Application • For connecting Geberit AquaClean enhancement solutions to concealed cistern • For use with Geberit Duofix, GIS, Kombifix and Sanbloc elements • For concealed cisterns with pre-mounted conduit pipe for the water supply connection • For connection to Geberit Kappa concealed cistern 15 cm (UP200); use separate water supply connection set • For connecting Geberit AquaClean complete solutions to Geberit Duofix Special elements, barrier-free • For connecting Geberit AquaClean complete solutions to Geberit Duofix Special elements, height-adjustable Characteristics • Special production to meet the standard BS 6920 Ordering Information Article no. PU1 241.819.00.1 1 Geberit water supply connection Geberit Sigma concealed cistern 8 cm (UP720), for Geberit AquaClean Additional Note Angle stop valve R 1/2"; 2 metal-reinforced hoses R 3/8"; Y-branch; Connection material Ordering Information Article no. PU1 249.801.00.1 1 Application • For use with Geberit Sigma concealed cistern 8 cm (UP720), front actuation • For connecting Geberit AquaClean Geberit AquaClean 4000, 5000 & 5000plus water supply connection set for UP200 / Duofix WC frame 0.82 cm New Ordering Information Article no. PU1 242.413.00.1 1 Geberit AquaClean 5000 & 5000plus standard connection set New Application • For connecting Geberit AquaClean enhancement solutions to concealed cistern • For UP200 concealed cistern with top/front actuation • For use with installation elements with construction height 82 cm Additional Note 3 metal-reinforced hoses; Angle stop valve R 1/2"; Connection material Ordering Information Application Article no. PU1 240.634.00.1 1 • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus Ordering Information Article no. PU1 PU2 242.185.00.1 1 5 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. 86 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Geberit AquaClean Geberit AquaClean 4000, 5000 & 5000plus water supply connection set for UP200 / Duofix WC frame 0.98 cm New Geberit AquaClean 8000plus active carbon filter and nozzle cleaner 1 pcs New Application Application • For connecting Geberit AquaClean enhancement solutions to concealed cistern • For UP200 concealed cistern with top/front actuation • For installation elements with construction height 98 cm Additional Note 3 metal-reinforced hoses; Angle stop valve R 1/2"; Connection material Ordering Information Article no. PU1 240.635.00.1 1 • For use with Balena 8000 • For use with Geberit AquaClean 8000plus Ordering Information Article no. PU1 PU4 240.625.00.1 1 144 Geberit AquaClean 8000plus active carbon filter and nozzle cleaner 2 pcs New Geberit AquaClean consumables Geberit AquaClean 8000plus nozzle cleaner Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus Ordering Information Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus Article no. PU1 PU4 240.626.00.1 1 144 Characteristics • For approx. 750 uses (400 ml) • Dermatologically tested Ordering Information Article no. PU1 PU2 242.545.00.1 1 12 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. Product and Installation Guide Washroom & Bathroom 2011 87 Product Guide Geberit AquaClean Geberit AquaClean cleaning agent New Geberit AquaClean 5000plus active carbon filter set New Application • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus Application • For cleaning Geberit AquaClean devices Ordering Information Characteristics • Content 500 ml • Can be used immediately and undiluted • Environmentally friendly PU1 PU2 242.546.00.1 1 10 PU1 PU2 240.116.00.1 1 30 Geberit AquaClean 5000plus and 8000plus battery set for remote control New Ordering Information Article no. Article no. Application Geberit AquaClean cleaning agent with cloth New • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Geberit AquaClean 5000plus Additional Note Set of 3 Ordering Information Article no. PU1 147.008.00.1 1 Application • For cleaning Geberit AquaClean devices Additional Note Geberit AquaClean cleaning agent; Cleaning cloth Ordering Information Article no. PU1 PU2 242.547.00.1 1 10 Geberit AquaClean 8000plus active carbon filter Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus Ordering Information Article no. PU1 PU2 250.022.00.1 1 100 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. 88 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Geberit AquaClean Geberit AquaClean 8000 shower nozzle Geberit AquaClean spare parts Geberit AquaClean 8000plus set shower and dryer nozzle Application • For use with Geberit AquaClean 8000 Application Ordering Information • For use with Balena 8000 • For use with Geberit AquaClean 8000plus Article no. PU1 250.071.00.1 1 Ordering Information Article no. PU1 PU2 242.394.00.1 1 10 Geberit AquaClean 8000plus & 8000 seat and lid Geberit AquaClean 8000plus remote control wall holder Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Geberit AquaClean 8000 Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus Ordering Information Article no. Colour PU1 PU2 Ordering Information 250.034.11.1 White alpine 1 5 Article no. PU1 250.032.00.1 1 Geberit AquaClean 8000plus & 8000 lid Geberit AquaClean 8000plus remote control Application Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Geberit AquaClean 8000 Product Details Radio frequency 2.4 GHz Ordering Information Article no. PU1 250.043.00.1 1 Ordering Information Article no. Colour PU1 250.067.11.1 White alpine 1 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. Product and Installation Guide Washroom & Bathroom 2011 89 Product Guide Geberit AquaClean Geberit AquaClean 8000plus & 8000 seat Geberit AquaClean 8000plus & 8000 damper white for seat - right New Application Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Geberit AquaClean 8000 • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Geberit AquaClean 8000 Ordering Information Ordering Information Article no. Colour PU1 250.066.11.1 White alpine 1 Geberit AquaClean 8000plus & 8000 casing Article no. PU1 250.068.00.1 1 Geberit AquaClean 8000plus & 8000 cover right New Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Geberit AquaClean 8000 Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Geberit AquaClean 8000 Ordering Information Ordering Information Article no. Colour PU1 PU4 250.029.11.1 White alpine 1 6 Article no. PU1 250.026.00.1 1 Geberit AquaClean 8000plus & 8000 O-ring for shower arm New Geberit AquaClean 8000plus & 8000 damper, white Application Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Geberit AquaClean 8000 Ordering Information Article no. PU1 Ordering Information 240.665.00.1 1 Article no. PU1 PU2 250.069.00.1 1 10 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. 90 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Geberit AquaClean Geberit AquaClean 8000plus & 8000 screw for casing New Geberit AquaClean 8000plus & 8000 acoustic insulation set Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Geberit AquaClean 8000 Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Geberit AquaClean 8000 Ordering Information Article no. PU1 250.079.11.1 1 Additional Note Sound insulation mat; 2 sleeves Geberit AquaClean 8000plus & 8000 anti-slip strip set Ordering Information New Article no. PU1 250.027.00.1 1 Geberit AquaClean 5000plus remote control New Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Geberit AquaClean 8000 Application • For use with Geberit AquaClean 5000plus Ordering Information Ordering Information Article no. PU1 250.037.11.1 1 Geberit AquaClean 8000plus & 8000 maintenance flap Article no. PU1 242.169.11.1 1 Geberit AquaClean 5000plus dryer flap New Application • For use with Geberit AquaClean 5000plus Application • For use with Balena 8000 • For use with Geberit AquaClean 8000plus • For use with Geberit AquaClean 8000 Ordering Information Article no. PU1 PU2 242.184.11.1 1 20 Ordering Information Article no. Colour PU1 250.030.11.1 White alpine 1 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. Product and Installation Guide Washroom & Bathroom 2011 91 Product Guide Geberit AquaClean Geberit AquaClean 5000plus wall mounted holder for remote control New Geberit AquaClean 5000 & 5000plus filter New Application • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus Application Ordering Information • For use with Geberit AquaClean 5000plus Ordering Information Article no. PU1 240.057.11.1 1 Article no. PU1 PU2 242.187.00.1 1 10 Geberit AquaClean 5000 & 5000plus adaptor plate New Geberit AquaClean 5000 & 5000plus WC seat lid New Application • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus Application • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus Characteristics Ordering Information • Dowel with clamping range 13–16 mm and 15–18 mm Article no. PU1 242.181.11.1 1 Additional Note Connection material; Allen key; 4 dowels Ordering Information Geberit AquaClean 5000 & 5000plus WC seat New Article no. PU1 240.495.00.1 1 Geberit AquaClean 5000 & 5000plus spray nozzle New Application • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus Ordering Information Article no. PU1 242.179.11.1 1 242.180.11.1 1 Application • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus Ordering Information Article no. PU1 240.226.11.1 1 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. 92 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Geberit AquaClean Geberit AquaClean 5000 & 5000plus cover filter compartment New Geberit AquaClean 5000 & 5000plus compensation pad set raised New Application Application • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus Ordering Information Article no. PU1 PU2 242.182.11.1 1 12 Additional Note Set of 4 Ordering Information Article no. Geberit AquaClean 5000 & 5000plus cover for electrical connection PU1 241.517.CG.1 1 New Geberit AquaClean 5000 & 5000plus compensation pad set New Application • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus Ordering Information Article no. PU1 PU2 Application 242.183.11.1 1 15 • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus Geberit AquaClean 5000 & 5000plus hinge set New Additional Note Set of 4 Ordering Information Article no. PU1 241.516.CG.1 1 Geberit AquaClean 5000 & 5000plus pad set for WC lid New Application • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus Ordering Information Article no. PU1 242.186.11.1 1 Application • For use with Geberit AquaClean 5000 Ordering Information Article no. PU1 242.286.CG.1 1 PU2 50 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. Product and Installation Guide Washroom & Bathroom 2011 93 Product Guide Geberit AquaClean Geberit AquaClean 4000 securing clip to WC lid New Geberit AquaClean 4000 WC seat Application • For use with Geberit AquaClean 4000 Application Ordering Information • For use with Geberit AquaClean 4000 Ordering Information Article no. PU1 242.171.11.1 1 242.170.11.1 1 Article no. PU1 242.178.11.1 1 Geberit AquaClean 4000 pad set for WC lid New Geberit AquaClean 4000 WC seat lid Application • For use with Balena 4000 • For use with Geberit AquaClean 4000 Ordering Information Application Article no. PU1 147.231.00.1 1 • For use with Geberit AquaClean 4000 Ordering Information Geberit AquaClean 4000 pin set for WC seat/lid New Article no. PU1 PU2 242.172.11.1 1 7 Geberit AquaClean 4000 filter New Application • For use with Geberit AquaClean 4000 Ordering Information Application Article no. PU1 242.175.00.1 1 • For use with Balena 4000 • For use with Geberit AquaClean 4000 Ordering Information Article no. PU1 147.235.00.1 1 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. 94 Product and Installation Guide Washroom & Bathroom 2011 Product Guide Geberit AquaClean Geberit AquaClean 4000 O-ring set for spray arm New Geberit AquaClean 4000 spray nozzle with 5 holes New Application Application • For use with Geberit AquaClean 4000 • For use with Geberit AquaClean 4000 • For use with Geberit AquaClean 4000 • For use with Balena 4000 Ordering Information Ordering Information Article no. PU1 242.176.00.1 1 Geberit AquaClean 4000 compensation pad set raised New Article no. PU1 PU2 242.376.00.1 1 100 Geberit AquaClean 4000, 5000 & 5000plus fastening set New Application • For use with Geberit AquaClean 4000 Ordering Information Article no. PU1 242.174.00.1 1 Ordering Information Article no. PU1 849.825.00.1 1 Geberit AquaClean 4000 compensation pad set New Geberit AquaClean waterstream cover Application Application • For use with Geberit AquaClean 4000 • For use with Geberit AquaClean 4000 • For use with Geberit AquaClean 5000 • For use with Geberit AquaClean 5000plus • For use with Geberit AquaClean 8000 • For use with Geberit AquaClean 8000plus Ordering Information Article no. PU1 242.173.00.1 1 Ordering Information Geberit AquaClean 4000 spray nozzle with 3 holes New Article no. Colour PU1 813.224.15.0 Glass clearly 1 Application • For use with Geberit AquaClean 4000 • For use with Geberit AquaClean 4000 Ordering Information Article no. PU1 PU2 242.377.00.1 1 100 Note The Geberit AquaClean range is only available to displaying retailers. Please contact 0800 032 9629 for further information. Product and Installation Guide Washroom & Bathroom 2011 95 Product Guide Geberit AquaClean 96 Product and Installation Guide Washroom & Bathroom 2011 Spares Spares Duofix WC frames Duofix WC frames Spares Duofix WC frames 111.383.00.5 Duofix WC frame 1.12 m with UP320 for Sigma flush plates - PreWall 111.384.00.5 Duofix WC frame 1.12 m with UP320 for Sigma flush plates Ordering Information 19.1 16 17 15 14 15.1 14.1 14.2 14.3 17.1 19 18 816.418 19.2 13 21 20 2 13 20.1 3 1 4 Pos. Article no. Description 1 241.869.00.1 Mounting accessories 2 241.824.00.1 Inner cover 3 241.826.00.1 Protection housing 4 362.771.00.1 Seal for flush pipe 5 362.796.92.1 Protection cover for flush pipe 6 240.189.00.1 Threaded rod (pr) 7 152.426.46.1 WC Connection Set 7.1 152.426.11.1 WC Connection Set 7.2 217.713.46.1 Chrome Caps & Washers Gloss 7.3 119.668.00.1 Flush pipe seal 7.4 152.424.00.1 Rubber collar 8 366.061.16.1 90 mm HDPE 90 Degree bend 8.1 387.282.00.1 Collar for outlet bend 9 366.820.92.1 Protection cover 10 367.928.16.1 90/110 mm Adaptor 11 242.012.00.1 Complete pipe bracket 11.1 242.017.00.1 Pipe bracket clip 12 242.010.00.1 Conduit pipe for shower toilet water supply 13 111.892.00.1 Hexagonal self tapping screws 14 240.269.00.1 Water supply connection R 1/2" with integrated angle stop valve 14.1 240.298.00.1 Spindle for isolation valve 14.2 240.347.00.1 Hand wheel 14.3 241.857.00.1 Nut for isolation valve 15 241.982.00.1 Stainless steel connection hose 15.1 240.922.00.1 EPDM O Ring 7.5 x 1.5 mm / 19 x 2 mm 16 240.923.00.1 Connection clip for fill valve 17 240.705.00.1 Side fill valve for Duofix 17.1 240.771.00.1 Diaphragm for side fill valve 18 241.858.00.1 Complete flush valve with basket 19 240.622.00.1 Complete flush valve 19.1 241.167.00.1 Clip set for flush valves 19.2 816.418.00.1 Flush valve seal 20 241.859.00.1 Basket for flush valve 20.1 241.868.00.1 Seal for basket 21 241.829.00.1 Cradle assembly for push rods 5 12 6 11.1 11 7 8 7.1 7.2 7.3 8.1 10 9 Buy spares direct on 01789 842127 Product and Installation Guide Washroom & Bathroom 2011 97 Spares Spares Duofix WC frames 111.383.00.1 Duofix WC frame 1.12 m with UP300 cistern - PreWall 111.384.00.1 Duofix WC frame 1.12 m with UP300 cistern Ordering Information Pos. Article no. Description 1 240.930.00.1 Inner cover 2 240.931.00.1 Protection housing 3 240.929.00.1 Cradle assembly for push rods 4 240.705.00.1 Side fill valve for Duofix 4.1 240.771.00.1 Diaphragm for side fill valve 5 240.923.00.1 Connection clip for fill valve 6 241.982.00.1 Stainless steel connection hose 6.1 240.922.00.1 EPDM O Ring 7.5 x 1.5mm / 19 x 2mm 7 240.177.00.1 Servicing (stop) valve 7.1 240.925.00.1 Spindle for isolation valve 7.2 240.623.00.1 Nut for isolation valve 8 240.622.00.1 Complete flush valve 8.1 241.167.00.1 Clip set for flush valves 8.2 240.927.00.1 Part flush rod for valve 8.3 816.418.00.1 Flush valve seal 8.4 240.695.00.1 Holder for flush valve 9 240.928.00.1 Basket for flush valve 9.1 240.282.00.1 Seal for basket 10 362.771.00.1 Seal for flush pipe 11 362.796.92.1 Protection cover for flush pipe 12 111.892.00.1 Hexagonal self tapping screws 13 240.972.00.1 Complete pipe bracket 13.1 240.417.00.1 Pipe bracket clip 14 240.189.00.1 Threaded rod (pr) 15 366.061.16.1 90mm HDPE 90 degree bend 16 367.928.16.1 90/110mm Adaptor 17 152.426.46.1 WC connection set 17.1 217.713.46.1 Chrome caps & washers 17.2 152.434.06.1 WC flush pipe connector & collar 17.3 119.668.00.1 Flush pipe seal 17.4 152.424.00.1 Rubber collar 17.5 152.425.46.1 Pan connector Buy spares direct on 01789 842127 98 Product and Installation Guide Washroom & Bathroom 2011 Spares Spares Duofix WC frames 111.242.00.1 Duofix WC frame 0.82 m with UP200 cistern - PreWall 111.292.00.1 Duofix WC frame 0.98 m with UP200 cistern - PreWall Ordering Information 6 5.1 5 4 4.1 4.2 Pos. Article no. Description 1 240.206.00.1 Inner cover 2 240.172.00.1 Protection housing 3 240.533.00.1 Cradle assembly for push rods 4 240.269.00.1 Servicing (stop) valve complete 4.1 240.347.00.1 Knob for isolation valve 4.2 240.298.00.1 Spindle for isolation valve 4.3 240.623.00.1 Nut for isolation valve 5 240.705.00.1 Side fill valve 5.1 240.771.00.1 Diaphragm for side fill valve 6 240.846.00.1 Stainless steel connection hose 6.1 240.922.00.1 EPDM O Ring 7.5 x 1.5mm / 19 x 2mm 7 240.637.00.1 Complete flush valve 8 240.638.00.1 Flush valve 8.1 816.418.00.1 Flush valve seal 9 240.928.00.1 Basket for flush valve 9.1 240.282.00.1 Seal for basket 10 362.771.00.1 Seal for flush pipe 11 362.796.92.1 Protection cover for flush pipe 12 240.189.00.1 Threaded rod (pr) 13 240.972.00.1 Complete pipe bracket 13.1 240.417.00.1 Pipe bracket clip 14 152.426.46.1 WC connection set 14.1 217.713.46.1 Chrome caps & washers 14.2 119.668.00.1 Flush pipe seal 14.3 152.424.00.1 Rubber collar 15 366.061.16.1 90 mm HDPE 90 degree bend 15.1 387.282.00.1 90 mm seal 16 366.820.92.1 Protection cover 17 367.928.16.1 90/110 mm Adaptor 18 111.892.00.1 Hexagonal self tapping screws 4.3 6.1 1 18 3 2 18 12 12 13.1 10 11 8 14 7 8.1 14.1 13 14.2 15 9 16 9.1 14.3 15.1 17 Buy spares direct on 01789 842127 Product and Installation Guide Washroom & Bathroom 2011 99 Spares Spares Duofix WC frames 111.253.00.1 WC frame 0.88 m - PreWall 111.254.00.1 WC frame 0.82 m - PreWall Ordering Information Pos. Article no. Description 1 240.206.00.1 Inner cover 2 240.172.00.1 Protection housing 3 240.079.00.1 Cradle assembly for push rods 4 240.705.00.1 Side fill valve for Duofix 4.1 240.771.00.1 Diaphragm for side fill valve 5 241.016.00.1 Stainless steel connection hose 5.1 240.922.00.1 EPDM O Ring 7.5 x 1.5mm / 19 x 2mm 6 240.177.00.1 Servicing (stop) valve for Duofix II 6.1 240.925.00.1 Spindle for isolation valve 6.2 240.623.00.1 Nut for isolation valve 7 240.122.00.1 Complete flush valve for 0.82/0.88 cistern 7.1 241.167.00.1 Clip set for flush valves 7.2 816.418.00.1 Flush valve seal 8 240.500.00.1 Basket for flush valve 8.1 240.282.00.1 Seal for basket 9 362.771.00.1 Seal for flush pipe 10 362.796.92.1 Protection cover for flush pipe 11 111.892.00.1 Hexagonal self tapping screws 12 240.972.00.1 Complete pipe bracket 13 240.189.00.1 Threaded rods (pair) 14 366.061.16.1 90 mm HDPE 90 degree bend 15 367.928.16.1 90/110mm Adaptor 16 152.426.46.1 WC connection set 16.1 217.713.46.1 Chrome caps & washers 16.2 152.434.06.1 WC flush pipe connector & collar 16.3 119.668.00.1 Flush pipe seal 16.4 152.424.00.1 Rubber collar 16.5 152.425.46.1 Pan connector Buy spares direct on 01789 842127 100 Product and Installation Guide Washroom & Bathroom 2011 Spares Spares Concealed cisterns Concealed cisterns Concealed cisterns 109.309.00.5 Concealed dual flush cistern UP320 Ordering Information 15 1 15.1 15.2 15.3 2 2.1 14 4.1 13 13 4 8 7 3 6 4.2 Pos. Article no. Description 1 240.923.00.1 Connection clip for fill valve 2 240.705.00.1 Side fill valve for Duofix 2.1 240.771.00.1 Diaphragm for side fill valve 3 241.858.00.1 Complete flush valve with basket 4 240.622.00.1 Complete flush valve 4.1 241.167.00.1 Clip set for flush valves 4.2 816.418.00.1 Flush valve seal 5 241.859.00.1 Basket for flush valve 5.1 241.868.00.1 Seal for basket 6 241.826.00.1 Protection housing 7 241.824.00.1 Inner cover 8 241.829.00.1 Cradle assembly for push rods 9 241.378.00.1 Concealed flush pipe fixing set 10 119.652.16.1 Concealed flush pipe 10.1 362.771.00.1 Seal for flush pipe ø 45 mm 10.2 362.796.92.1 Protection cover for flush pipe 11 892.975.00.1 O Ring seal 12 889.711.00.1 Fixing slider 13 465.027.00.1 Wall brackets and screws (pair) 14 241.982.00.1 Stainless steel connection hose 15 240.269.00.1 Water supply connection R 1/2“ with integrated angle stop valve 15.1 240.347.00.1 Hand wheel 15.2 240.298.00.1 Spindle for isolation valve 15.3 241.857.00.1 Nut for isolation valve 816.418 12 11 5 5.1 10 10.1 10.2 9 Buy spares direct on 01789 842127 Product and Installation Guide Washroom & Bathroom 2011 101 Spares Spares Concealed cisterns 109.309.00.1 Concealed dual flush cistern UP300 Ordering Information Pos. Article no. Description 1 240.930.00.1 Inner cover 2 240.931.00.1 Protection housing 3 240.929.00.1 Cradle assembly for push rods 4 240.705.00.1 Side fill valve for Duofix 4.1 240.771.00.1 Diaphragm for side fill valve 5 240.923.00.1 Connection clip for fill valve 6 241.982.00.1 Stainless steel connection hose 7 240.177.00.1 Servicing (stop) valve 7.1 240.925.00.1 Spindle for isolation valve 7.2 240.623.00.1 Nut for isolation valve 8 240.622.00.1 Complete flush valve 8.1 241.167.00.1 Clip set for flush valves 8.2 240.927.00.1 Part flush rod for valve 8.3 816.418.00.1 Flush valve seal 8.4 240.695.00.1 Holder for flush valve 9 240.928.00.1 Basket for flush valve 9.1 240.282.00.1 Seal for basket 10 892.975.00.1 O Ring seal 11 119.652.16.1 Concealed flush pipe 11.1 362.771.00.1 Seal for flush pipe 11.2 362.796.92.1 Protection cover for flush pipe 12 241.378.00.1 Concealed flush pipe fixing set 13 465.027.00.1 Wall brackets and screws (pair) 14 152.434.06.1 WC flush pipe connector and collar 14.1 119.668.00.1 Flush pipe seal Buy spares direct on 01789 842127 102 Product and Installation Guide Washroom & Bathroom 2011 Spares Spares Concealed cisterns 109.200.00.1 Concealed dual flush cistern UP200 Ordering Information Pos. Article no. Description 1 240.206.00.1 Inner cover 2 240.172.00.1 Protection housing 3 240.533.00.1 Cradle assembly for push rods 4 240.269.00.1 Servicing (stop) valve complete 4.1 240.347.00.1 Knob for isolation valve 4.2 240.298.00.1 Spindle for isolation valve 4.3 240.623.00.1 Nut for isolation valve 5 240.705.00.1 Side fill valve 5.1 240.771.00.1 Diaphragm for side fill valve 6 240.846.00.1 Stainless steel connection hose 6.1 240.922.00.1 EPDM O Ring 7.5 x 1.5mm / 19 x 2mm 7 240.637.00.1 Complete flush valve 8 240.638.00.1 Flush valve 8.1 241.167.00.1 Clip set for flush valve 8.2 816.418.00.1 Flush valve seal 9 240.928.00.1 Basket for flush valve 9.1 240.282.00.1 Seal for basket 10 362.771.00.1 Seal for flush pipe 11 362.796.92.1 Protection cover for flush pipe 12 241.378.00.1 Concealed flush pipe fixing set 13 152.434.06.1 WC flush pipe connector and collar 13.1 119.668.00.1 Flush pipe seal Pos. Article no. Description 1 890.240.11.1 Cover 2 240.700.00.1 Side fill valve 2.1 240.771.00.1 Diaphragm for side fill valve 3 240.573.00.1 Pneumatic actuation unit single flush 4 240.576.00.1 Flush valve 4.1 816.418.00.1 Flush valve seal 5 256.000.00.1 Air hose 3.5m 6 118.006.11.1 Flush bend 7 119.668.00.1 Flush seal for pan 123.137.11.1 Concealed single flush cistern AP123 Ordering Information Not Illustrated 294.802.00.1 Wall brackets 240.139.00.1 Seal kit Buy spares direct on 01789 842127 Product and Installation Guide Washroom & Bathroom 2011 103 Spares Spares Concealed cisterns 109.720.00.1 Concealed dual flush cistern for low height furniture 109.721.00.1 Concealed single flush cistern low height furniture Ordering Information Pos. Article no. Description 1 281.206.00.1 Bottom fill valve 1.1 241.813.00.1 Seal set for bottom fill valve 2 241.415.00.1 Flush valve 2.1 816.418.00.1 Flush valve seal 3 240.574.00.1 Pneumatic actuation unit* 4 241.414.00.1 Cover plate/lid 5 241.413.21.1 Dual flush button* 6 240.575.00.1 Double air hose* 7 119.705.93.1 Flush bend 8 119.668.00.1 Flush seal for pan *Dual flush only. For single flush: 240.573.00.1 Pneumatic actuation unit 256.000.00.1 Air hose 3.5m Not Illustrated 240.139.00.1 Seal kit 109.722.00.1 Mechanical operated concealed dual flush cistern for low height furniture - plastic button 109.723.00.1 Mechanical operated concealed dual flush cistern for low height furniture - metal button Ordering Information 1 1.1 3 6 CL 7 WL 2 4 2.1 Pos. Article no. Description 1 281.206.00.1 Bottom fill valve 1.1 241.813.00.1 Seal set for bottom fill valve 2 241.415.00.1 Flush Valve 2.1 816.418.00.1 Flush valve seal 3 241.976.00.1 Mechanical actuation unit 4 241.414.00.1 Cover plate/lid 5 119.705.93.1 Flush bend 5.1 119.668.00.1 Flush seal for pan 6 241.978.21.1 241.978.21.Z 7 241.979.00.1 Dual flush button, plastic Dual flush button, galvanized Counter nut Not Illustrated 240.139.00.1 5 Seal kit 5.1 Buy spares direct on 01789 842127 104 Product and Installation Guide Washroom & Bathroom 2011 Spares Spares WC flush plates WC flush plates WC flush plates 115.778.XX.1 Sigma20 dual flush plate for UP320 115.788.XX.1 Sigma50 dual flush plate for UP320 Ordering Information Pos. Article no. 1 241.876.00.1 Flush plate fixing frame for tool-free installation 2 241.874.00.1 Push rods and distance rods for tool-free installation 3 240.938.00.1 Extension set 4 241.295.00.1 Spring 1 2 3 2 4 4 4 4 2 Description 2 Note: Samba, Bolero, Twist compatible after 1st April 2008 115.758.XX.1 Sigma10 single flush plate for UP320 Ordering Information 2 1 3 2 2 Pos. Article no. Description 1 241.876.00.1 Flush plate fixing frame 2 241.874.00.1 Push rods and distance rods for tool-free installation 3 240.938.00.1 Extension set Note: Rumba, Mambo and Tango compatible after 1st April 2008 Buy spares direct on 01789 842127 Product and Installation Guide Washroom & Bathroom 2011 105 Spares Spares WC flush plates 115.770.XX.1 Samba dual flush plate 115.777.XX.1 Bolero dual flush plate 115.780.XX.1 Twist dual flush plate 115.782.XX.1 Twist dual flush plate anti vandal Ordering Information Pos. Article no. Description 1 813.514.00.1 Spring 2 240.935.00.1 Flush plate fixing frame 2.1 240.934.00.1 Push rod locking piece 3 240.936.00.1 Push rods (pair) 4 240.173.00.1 Distance rods (pair) 5 240.930.00.1 Inner cover Note: For post May 2008 installation please use Sigma spares list 115.750.XX.1 Rumba single flush plate 115.751.XX.1 Mambo single flush plate 115.760.XX.1 Tango single flush plate Ordering Information Pos. Article no. Description 1 813.514.00.1 Spring 2 240.935.00.1 Flush plate fixing frame 2.1 240.933.00.1 Push rod locking piece 3 240.936.00.1 Push rods (pair) 4 240.173.00.1 Distance rods (pair) 5 240.930.00.1 Inner cover Note: For post May 2008 installation please use Sigma spares list Buy spares direct on 01789 842127 106 Product and Installation Guide Washroom & Bathroom 2011 Spares Spares WC flush plates 115.228.XX.1 Kappa20 dual flush plate 115.260.XX.1 Kappa50 dual flush plate Ordering Information 4 5 2 3 Pos. Article no. Description 1 241.295.00.1 Spring 2 240.639.00.1 Push rods and distance rods (pair) 3 240.646.00.1 Flush plate fixing frame 4 240.206.00.1 Inner cover 5 240.938.00.1 Extension set (order separately) 2 1 1 2 115.666.XX.1 Artline dual flush plate Ordering Information Pos. Article no. Description 1 813.514.00.1 Spring 2 240.207.00.1 Push rods (pair) 3 240.646.00.1 Flush plate fixing frame 4 240.173.00.1 Distance rods (pair) 5 240.206.00.1 Inner cover Note: For post 2006 Artline installation please use the Kappa spares list Buy spares direct on 01789 842127 Product and Installation Guide Washroom & Bathroom 2011 107 Spares Spares Duofix urinal frames 111.623.00.1 Duofix urinal frame 111.622.00.1 Duofix urinal frame with pipe interruptor Ordering Information 11 1 12 2 11 3 4 4.1 5 6 Pos. Article no. Description 1 242.195.00.1 Hose R8 for inlet UR-element 2 242.039.00.1 Crossbar for water supply 32 mm 3 152.489.16.1 Inlet connector & collar 4 242.045.00.1 Fixation rods complete 4.1 242.046.00.1 Plastic nut for urinal fastening 5 240.027.46.1 Chrome caps & washers 6 242.210.00.1 Cross bar metal for urinal element for outlet 7 152.950.11.1 Urinal trap 7 152.983.00.1 Urinal trap 8 240.306.00.1 Protection plug 9 240.315.00.1 Urinal outlet bend complete 9.1 152.693.00.1 Rubber collar reducer 63x50 10 242.516.00.1 Geberit straight connector, PVC d50 11 111.892.00.1 Hexagonal self tapping screws see 116.001.00.1 Urinal installation set universal 12 9 10 9.1 7 8 116.001.00.1 Urinal installation set universal 116.003.00.1 Urinal installation set with flush pipe Ordering Information 2 1 3 3.1 4 Pos. Article no. Description 1 242.130.00.1 Connection nipple urinal straight 2 242.131.00.1 Connection nipple urinal bent 3 241.934.00.1 Stop valve with throttle, complete 3.1 241.933.00.1 Regulating screw 4 241.930.00.1 Protection cover with protection cover lid 5 241.947.00.1 Insulation protection with connection terminal 6 242.156.00.1 Lip seal flushing pipe 6 5 Buy spares direct on 01789 842127 108 Product and Installation Guide Washroom & Bathroom 2011 Spares Spares Fill and flush valves for ceramic cisterns 111.674.00.1 Duofix urinal frame 111.667.00.1 Duofix urinal frame with pipe interruptor Ordering Information Pos. Article no. Description 1 240.534.00.1 Protection housing cover 2 115.832.00.1 Protection housing 3 240.517.00.1 Water part 3.1 241.060.00.1 Filter case & isolation valve 3.2 240.520.00.1 Filter 3.3 240.871.00.1 Flat seal 4 240.518.00.1 Dummy cover with seal 5 241.061.00.1 Complete nipple 6 240.522.00.1 Electrical isolation cover 7 242.516.00.1 Geberit straight connector, PVC d50 7.1 152.693.00.1 Rubber collar reducer 63x50 8 240.306.00.1 Protection plug 9 152.983.00.1 Urinal trap 10 240.027.46.1 Chrome caps & washers 11 242.045.00.1 Fixation rods complete 11.1 242.046.00.1 Plastic nut for urinal fastening 12 152.489.16.1 Inlet connector & collar 13 242.041.00.1 Crossbar for water supply di 32mm 14 242.047.00.1 Crossbar for drainage 15 111.892.00.1 Hexagonal self tapping screws 16 242.005.00.1 Inlet hose for urinal frame 17 115.801.00.1 Universal urinal housing Pos. Article no. Description 1 240.771.00.1 Diaphragm assembly 2 261.358.00.1 Stainless steel connection hose 3/8" 3 240.846.00.1 Stainless steel connection hose Fill and flush valves for ceramic cisterns Fill and flush valves for ceramic cisterns 240.700.00.1 Impuls380 side fill valve 240.705.00.1 Impuls380 side fill valve Ordering Information Buy spares direct on 01789 842127 Product and Installation Guide Washroom & Bathroom 2011 109 Spares Spares Fill and flush valves for ceramic cisterns 281.206.00.1 Impuls360 bottom fill valve Ordering Information Pos. Article no. Description 1 241.813.00.1 Seal set Pos. Article no. Description 1 241.800.KD.1 Flush button 2 241.801.00.1 Basket 2.1 240.278.00.1 Overflow pipe 3 816.418.00.1 Flush valve seal 4 261.630.00.1 Connection set 4.1 241.350.00.1 Connection washer Impuls280 dual flush valve blue square design Ordering Information Buy spares direct on 01789 842127 110 Product and Installation Guide Washroom & Bathroom 2011 Installation Guide Waste and drainage connection 120 Product and Installation Guide Washroom & Bathroom 2011 Urinal Numerical index Article no. Page Article no. Page Article no. Page Article no. Page 47 115.760.11.1 18 115.788.SE.1 14 16 107.35.05B 65 115.210.GT.1 107.35.14B 65 115.214.CD.1 47 115.760.21.1 18 115.792.GH.1 107.35.24B 65 115.214.GT.1 47 115.760.45.1 18 115.798.00.1 20 107.35.34B 65 115.228.10.1 19 115.760.46.1 18 115.801.00.1 109 109.200.00.1 10 115.228.11.1 19 115.760.DT.1 18 115.831.00.1 60 109.211.00.1 11 115.228.21.1 19 115.760.GM.1 18 115.832.00.1 109 109.309.00.5 9 115.228.46.1 19 115.760.HC.1 18 115.855.00.1 25 12 115.228.CG.1 19 115.760.KA.1 18 115.857.00.1 26 109.772.00.1 10 115.228.DK.1 19 115.765.46.1 20 115.857.21.1 26 111.242.00.1 5 115.228.DT.1 19 115.770.10.1 17 115.860.00.1 60 111.292.00.1 5 115.228.DW.1 19 115.770.11.1 17 115.890.00.1 25 111.352.00.5 8 115.228.EP.1 19 115.770.21.1 17 115.891.00.1 26 111.383.00.5 3 115.228.FB.1 19 115.770.46.1 17 115.918.00.1 24 4 115.228.FR.1 19 115.770.CG.1 17 115.939.00.1 24 7 115.228.GM.1 19 115.770.DK.1 17 115.941.11.1 23 28 115.228.KB.1 19 115.770.DT.1 17 115.941.KA.1 23 111.494.00.1 27 115.240.KH.1 19 115.770.DW.1 17 115.942.11.1 23 111.495.00.1 27 115.240.KJ.1 19 115.770.EP.1 17 115.942.KA.1 23 111.543.00.1 43 115.240.KK.1 19 115.770.FB.1 17 115.943.21.1 22 111.544.00.1 42 115.240.KL.1 19 115.770.FR.1 17 115.947.00.1 21 111.545.00.1 42 115.240.KM.1 19 115.770.GM.1 17 115.947.21.1 21 44 115.240.KN.1 19 115.770.KB.1 17 115.949.21.1 22 45 115.258.00.1 19 115.777.10.1 17 115.999.21.1 23 6 115.260.11.1 19 115.777.11.1 17 116.001.00.1 45 111.729.00.1 6 115.260.21.1 19 115.777.21.1 17 116.003.00.1 46 111.731.00.1 72 115.260.46.1 19 115.777.46.1 17 116.011.11.1 51 111.743.00.1 72 115.260.HC.1 19 115.777.CG.1 17 116.011.21.1 51 111.790.00.1 8 115.322.11.1 85 115.777.DK.1 17 116.011.46.1 51 57 115.323.11.1 84 115.777.DT.1 17 116.012.11.1 52 59 115.324.SF.1 85 115.777.DW.1 17 116.012.21.1 52 59 115.324.SG.1 85 115.777.EP.1 17 116.012.46.1 52 59 115.325.SF.1 84 115.777.FB.1 17 116.013.FW.1 54 111.847.00.1 58 115.325.SG.1 84 115.777.FR.1 17 116.014.11.1 55 111.859.00.1 46 115.612.00.1 17 115.777.GM.1 17 116.014.21.1 55 111.867.00.1 58 115.666.11.1 18 115.777.KB.1 17 116.014.46.1 55 111.868.00.1 58 115.666.21.1 18 115.778.KH.1 14 116.015.KH.1 47 58 115.666.46.1 18 115.778.KJ.1 14 116.015.KJ.1 47 57 115.680.11.1 19 115.778.KK.1 14 116.015.KK.1 47 57 115.680.21.1 19 115.778.KL.1 14 116.015.KL.1 47 57 115.723.21.1 30 115.778.KM.1 14 116.015.KM.1 47 111.874.00.1 57 115.725.21.1 31 115.778.KN.1 14 116.015.KN.1 47 111.878.00.1 57 115.733.21.1 29 115.785.00.1 15 116.016.00.1 49 111.887.00.1 59 115.738.21.1 29 115.785.11.1 16 116.016.11.1 49 111.889.00.1 60 115.739.21.1 30 115.785.DW.1 16 116.016.DW.1 49 111.892.00.1 97 115.740.21.1 28 115.785.EP.1 16 116.016.EP.1 49 98 115.750.11.1 18 115.785.GH.1 15 116.016.SC.1 49 99 115.750.21.1 18 115.785.SC.1 16 116.016.SD.1 49 100 115.750.46.1 18 115.785.SD.1 16 116.016.SE.1 49 111.892.00.1 108 115.750.KB.1 18 115.785.SE.1 16 116.021.11.1 51 111.892.00.1 109 115.751.00.1 18 115.788.00.1 14 116.021.21.1 51 115.075.21.1 23 115.758.KH.1 14 115.788.11.1 15 116.021.46.1 51 115.075.21.Z 24 115.758.KJ.1 14 115.788.DW.1 15 116.022.11.1 53 115.114.11.1 21 115.758.KK.1 14 115.788.EP.1 15 116.022.21.1 53 21 115.758.KL.1 14 115.788.GH.1 15 116.022.46.1 53 46 115.758.KM.1 14 115.788.SC.1 14 116.023.FW.1 54 47 115.758.KN.1 14 115.788.SD.1 14 116.024.11.1 56 109.720.00.1 111.384.00.5 111.399.00.5 111.493.00.1 111.622.00.1 111.623.00.1 111.706.00.1 111.830.00.1 111.835.00.1 111.843.00.1 111.844.00.1 111.869.00.1 111.871.00.1 111.872.00.1 111.873.00.1 111.892.00.1 111.892.00.1 111.892.00.1 115.114.21.1 115.200.11.1 115.210.CD.1 Product and Installation Guide Washroom & Bathroom 2011 121 Numerical index Article no. Page Article no. Page Article no. Page Article no. Page 104 152.438.46.1 65 240.116.00.1 88 116.024.21.1 56 119.705.93.1 116.024.46.1 56 119.705.93.1 104 152.489.16.1 108 240.122.00.1 100 116.025.KH.1 48 123.137.11.1 11 152.489.16.1 109 240.139.00.1 103 116.025.KJ.1 48 131.002.SI.1 13 152.693.00.1 108 240.139.00.1 104 116.025.KK.1 48 131.002.SJ.1 13 152.693.00.1 109 240.139.00.1 104 116.025.KL.1 48 131.002.SK.1 13 152.950.11.1 108 240.172.00.1 99 116.025.KM.1 48 131.021.SI.1 12 152.983.00.1 108 240.172.00.1 100 116.025.KN.1 48 131.021.SJ.1 12 152.983.00.1 109 240.172.00.1 103 116.026.GH.1 50 131.021.SK.1 12 154.005.00.1 74 240.173.00.1 106 116.031.11.1 52 131.023.SI.1 13 154.100.00.1 75 240.173.00.1 106 116.031.21.1 52 131.023.SJ.1 13 154.101.00.1 75 240.173.00.1 107 116.031.46.1 52 131.074.00.1 61 154.102.00.1 75 240.177.00.1 98 116.032.11.1 53 131.082.16.1 67 154.103.00.1 75 240.177.00.1 100 116.032.21.1 53 131.083.16.1 66 154.105.00.1 76 240.177.00.1 102 116.032.46.1 53 131.085.11.1 67 154.106.00.1 76 240.189.00.1 97 116.033.FW.1 55 131.088.29.1 66 154.107.00.1 76 240.189.00.1 98 116.034.11.1 56 131.104.00.1 60 154.108.00.1 76 240.189.00.1 99 116.034.21.1 56 131.105.00.1 61 154.130.00.1 75 240.189.00.1 100 116.034.46.1 56 131.108.11.1 67 154.131.00.1 75 240.206.00.1 99 116.035.KH.1 48 146.114.11.1 81 154.135.00.1 76 240.206.00.1 100 116.035.KJ.1 48 146.122.11.1 82 154.136.00.1 76 240.206.00.1 103 116.035.KK.1 48 146.132.11.1 83 154.299.00.1 76 240.206.00.1 107 116.035.KL.1 48 146.181.11.1 80 154.300.00.1 74 240.206.00.1 107 116.035.KM.1 48 147.008.00.1 88 154.301.00.1 74 240.207.00.1 107 116.035.KN.1 48 147.231.00.1 94 154.302.00.1 74 240.226.11.1 92 116.036.GH.1 50 147.235.00.1 94 154.303.00.1 74 240.269.00.1 97 116.107.21.1 38 150.247.00.1 71 154.304.00.1 75 240.269.00.1 99 116.108.21.1 39 150.535.21.1 68 154.305.00.1 75 240.269.00.1 101 116.117.21.1 39 150.536.21.1 68 154.306.00.1 75 240.269.00.1 103 116.118.21.1 40 150.679.21.1 71 154.330.00.1 73 240.278.00.1 110 116.127.21.1 38 150.688.21.1 71 154.330.11.1 73 240.282.00.1 98 116.128.21.1 40 150.712.21.1 69 154.330.21.1 73 240.282.00.1 99 116.135.21.1 32 150.713.21.1 69 154.330.FW.1 73 240.282.00.1 100 116.136.21.1 35 150.770.11.1 70 154.350.00.1 76 240.282.00.1 102 116.145.21.1 34 150.770.21.1 70 154.351.00.1 76 240.282.00.1 103 116.146.21.1 37 150.771.11.1 70 154.352.00.1 76 240.298.00.1 97 116.155.21.1 33 150.771.21.1 70 154.353.00.1 76 240.298.00.1 99 116.156.21.1 36 150.772.11.1 71 154.354.00.1 76 240.298.00.1 101 116.235.21.1 32 150.772.21.1 71 154.355.00.1 76 240.298.00.1 103 116.236.21.1 35 151.039.21.1 67 154.356.00.1 76 240.306.00.1 108 116.245.21.1 34 152.170.16.1 66 154.357.00.1 76 240.306.00.1 109 116.246.21.1 37 152.424.00.1 97 154.360.00.1 76 240.315.00.1 108 116.255.21.1 33 152.424.00.1 98 154.361.00.1 76 240.347.00.1 97 116.256.21.1 36 152.424.00.1 99 154.362.00.1 76 240.347.00.1 99 118.006.11.1 103 152.424.00.1 100 154.363.00.1 76 240.347.00.1 101 119.652.16.1 101 152.425.46.1 98 156.050.00.1 9 240.347.00.1 103 119.652.16.1 102 152.425.46.1 100 156.051.00.1 28 240.417.00.1 98 119.668.00.1 97 152.426.11.1 97 180.101.11.1 79 240.417.00.1 99 119.668.00.1 98 152.426.46.1 97 217.713.46.1 97 240.495.00.1 92 119.668.00.1 99 152.426.46.1 98 217.713.46.1 98 240.500.00.1 100 119.668.00.1 100 152.426.46.1 99 217.713.46.1 99 240.517.00.1 109 119.668.00.1 102 152.426.46.1 100 217.713.46.1 100 240.518.00.1 109 119.668.00.1 103 152.434.06.1 98 240.027.46.1 108 240.520.00.1 109 119.668.00.1 103 152.434.06.1 100 240.027.46.1 109 240.522.00.1 109 119.668.00.1 104 152.434.06.1 102 240.057.11.1 92 240.533.00.1 99 119.668.00.1 104 152.434.06.1 103 240.079.00.1 100 240.533.00.1 103 122 Product and Installation Guide Washroom & Bathroom 2011 Numerical index Article no. Page Article no. Page Article no. Page Article no. 240.871.00.1 109 241.350.00.1 110 242.012.00.1 Page 97 240.534.00.1 109 240.573.00.1 103 240.922.00.1 97 241.378.00.1 101 242.017.00.1 97 240.573.00.1 104 240.922.00.1 98 241.378.00.1 102 242.039.00.1 108 240.574.00.1 104 240.922.00.1 99 241.378.00.1 103 242.041.00.1 109 240.575.00.1 104 240.922.00.1 100 241.413.21.1 104 242.045.00.1 108 240.576.00.1 103 240.922.00.1 103 241.414.00.1 104 242.045.00.1 109 240.623.00.1 99 240.923.00.1 97 241.414.00.1 104 242.046.00.1 108 240.622.00.1 97 240.923.00.1 98 241.415.00.1 104 242.046.00.1 109 240.622.00.1 98 240.923.00.1 101 241.415.00.1 104 242.047.00.1 109 240.622.00.1 101 240.923.00.1 102 241.516.CG.1 93 242.130.00.1 108 240.622.00.1 102 240.925.00.1 98 241.517.CG.1 93 242.131.00.1 108 240.623.00.1 98 240.925.00.1 100 241.631.00.1 41 242.156.00.1 108 240.623.00.1 100 240.925.00.1 102 241.672.00.1 41 242.169.11.1 91 240.623.00.1 102 240.927.00.1 98 241.692.00.1 31 242.170.11.1 94 240.623.00.1 103 240.927.00.1 102 241.800.KD.1 110 242.171.11.1 94 240.625.00.1 87 240.928.00.1 98 241.801.00.1 110 242.172.11.1 94 240.626.00.1 87 240.928.00.1 99 241.813.00.1 104 242.173.00.1 95 240.634.00.1 81 240.928.00.1 102 241.813.00.1 104 242.174.00.1 95 240.634.00.1 82 240.928.00.1 103 241.813.00.1 110 242.175.00.1 94 240.634.00.1 83 240.929.00.1 98 241.819.00.1 79 242.176.00.1 95 240.634.00.1 86 240.929.00.1 102 241.819.00.1 80 242.178.11.1 94 240.635.00.1 81 240.930.00.1 98 241.819.00.1 86 242.179.11.1 92 240.635.00.1 82 240.930.00.1 102 241.824.00.1 97 242.180.11.1 92 240.635.00.1 83 240.930.00.1 106 241.824.00.1 101 242.181.11.1 92 240.635.00.1 87 240.930.00.1 106 241.826.00.1 97 242.182.11.1 93 240.637.00.1 99 240.931.00.1 98 241.826.00.1 101 242.183.11.1 93 240.637.00.1 103 240.931.00.1 102 241.829.00.1 97 242.184.11.1 91 240.638.00.1 99 240.933.00.1 106 241.829.00.1 101 242.185.00.1 86 240.638.00.1 103 240.934.00.1 106 241.857.00.1 97 242.186.11.1 93 240.639.00.1 107 240.935.00.1 106 241.857.00.1 101 242.187.00.1 92 240.646.00.1 107 240.935.00.1 106 241.858.00.1 97 242.195.00.1 108 240.646.00.1 107 240.936.00.1 106 241.858.00.1 101 242.210.00.1 108 240.665.00.1 90 240.936.00.1 106 241.859.00.1 97 242.286.CG.1 93 240.695.00.1 98 240.938.00.1 20 241.859.00.1 101 242.310.00.1 60 240.695.00.1 102 240.938.00.1 105 241.868.00.1 97 242.376.00.1 95 240.700.00.1 77 240.938.00.1 105 241.868.00.1 101 242.377.00.1 95 240.700.00.1 103 240.938.00.1 107 241.869.00.1 97 242.394.00.1 89 240.705.00.1 97 240.972.00.1 98 241.874.00.1 105 242.413.00.1 86 240.705.00.1 98 240.972.00.1 99 241.874.00.1 105 242.516.00.1 108 240.705.00.1 99 240.972.00.1 100 241.876.00.1 105 242.516.00.1 109 240.705.00.1 100 241.016.00.1 100 241.876.00.1 105 242.544.GH.1 16 240.705.00.1 101 241.060.00.1 109 241.894.00.1 60 242.545.00.1 87 240.705.00.1 102 241.061.00.1 109 241.930.00.1 108 242.546.00.1 88 240.705.00.1 103 241.144.00.1 22 241.933.00.1 108 242.547.00.1 88 240.771.00.1 97 241.167.00.1 97 241.934.00.1 108 249.801.00.1 81 240.771.00.1 98 241.167.00.1 98 241.947.00.1 108 249.801.00.1 82 240.771.00.1 99 241.167.00.1 100 241.976.00.1 104 249.801.00.1 83 240.771.00.1 100 241.167.00.1 101 241.978.21.1 104 249.801.00.1 86 240.771.00.1 101 241.167.00.1 102 241.978.21.Z 104 250.022.00.1 88 240.771.00.1 102 241.198.00.1 21 241.979.00.1 104 250.026.00.1 90 240.771.00.1 103 241.198.21.1 21 241.982.00.1 97 250.027.00.1 91 240.771.00.1 103 241.199.11.1 21 241.982.00.1 98 250.029.11.1 90 240.771.00.1 109 241.199.21.1 21 241.982.00.1 101 250.030.11.1 91 240.846.00.1 99 241.282.21.1 22 241.982.00.1 102 250.032.00.1 89 240.846.00.1 103 241.295.00.1 105 242.005.00.1 109 250.034.11.1 89 240.846.00.1 109 241.295.00.1 107 242.010.00.1 97 250.037.11.1 91 Product and Installation Guide Washroom & Bathroom 2011 123 Numerical index Article no. Page Article no. Page 250.043.00.1 89 813.514.00.1 250.066.11.1 90 813.514.00.1 107 250.067.11.1 89 816.418.00.1 97 250.068.00.1 90 816.418.00.1 98 250.069.00.1 90 816.418.00.1 99 250.071.00.1 89 816.418.00.1 100 250.079.11.1 91 816.418.00.1 101 256.000.00.1 103 816.418.00.1 102 104 816.418.00.1 103 261.157.00.1 77 816.418.00.1 103 261.358.00.1 109 816.418.00.1 104 261.630.00.1 110 816.418.00.1 104 281.206.00.1 77 816.418.00.1 110 281.206.00.1 104 849.825.00.1 95 281.206.00.1 104 889.711.00.1 101 282.350.KD.1 78 890.240.11.1 103 294.802.00.1 103 892.975.00.1 101 362.771.00.1 97 892.975.00.1 102 362.771.00.1 98 F107.35.09B 65 362.771.00.1 99 F107.35.18B 65 362.771.00.1 100 F107.35.29B 65 362.771.00.1 101 362.771.00.1 102 362.771.00.1 103 362.796.92.1 97 362.796.92.1 98 256.000.00.1 362.796.92.1 99 362.796.92.1 100 362.796.92.1 101 362.796.92.1 102 362.796.92.1 103 366.061.16.1 63 366.061.16.1 97 366.061.16.1 98 366.061.16.1 99 366.061.16.1 100 366.820.92.1 97 366.820.92.1 99 366.887.16.1 62 367.792.16.1 63 367.887.16.1 62 367.928.16.1 64 367.928.16.1 97 367.928.16.1 98 367.928.16.1 99 367.928.16.1 100 367.945.16.1 64 387.282.00.1 97 387.282.00.1 99 388.350.29.1 62 461.030.00.1 59 465.027.00.1 101 465.027.00.1 102 616.030.00.1 41 813.224.15.0 95 813.514.00.1 106 124 106 Product and Installation Guide Washroom & Bathroom 2011