Transcript
Product Information
CompactPCI® Pentium® M CPU Board • CD2-BEBOP Document No. 3236 • Edition 2008-02 Equipped with the Intel® Pentium® M processor up to 2GHz, the CD2-BEBOP is a high performance, low power 6U (double size Eurocard) CompactPCI® CPU board. The CD2-BEBOP is provided with an embedded graphics controller. The user can choose between a DVI-I receptacle, which allows for attachment of both, advanced (digital) and legacy (analog) flat panel displays and CRT monitors, or the classic VGA D-Sub connector. The Pentium® M (in particular the Low Voltage 1.4GHz chip) reduces the power consumption considerably compared to previous processor generations, thus enabling a reliable passive heatsink solution for thermal discharge. In addition to several USB2.0 ports, the CD2-BEBOP is equipped with four independent Ethernet controllers for high speed networking up to 1000Mbps. The PICMG® 2.16 Packet Switching Backplane is also supported (Dual Link Port).
For mass storage attachment, the CD2-BEBOP provides both Ultra ATA/100 IDE and RAID capable S-ATA interfaces. In addition, a socket for CompactFlash cards allows utilization of a silicon disk. The main memory is a SO-DIMM 200 DDR-SDRAM module up to 1GB capacity. An on-board USB2.0 FLASH disk drive up to 2GB is available as an option. The PMC mezzanine card socket enables on-board expansion of the CD2-BEBOP. Alternatively, an on-board hard disk drive module is optionally available which fits on the PMC slot as well. In addition to the front panel connectors, the optional CDY-RIO rear I/O transition module offers a variety of onboard and back panel connectors for a versatile usage of the CD2-BEBOP.
CD2-BEBOP -1EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU Feature Summary CD2-BEBOP Form Factor
Double size CompactPCI style Eurocard (160x233mm2), front panel width 4HP (20.3mm)
Processor
Designed for Intel® Pentium® M Micro FC-BGA 479 processors (0.13 Banias, 0.09 Dothan), maximum junction temperature 100°C • 600MHz ULV Celeron® M, 512KB L2 cache, 7W • 1.4GHz LV Pentium® M (Dothan733), 2MB L2 cache, 10W • 1.8GHz Pentium® M (Dothan745), 2MB L2 cache, 21W • 2.0GHz Pentium® M (Dothan755), 2MB L2 cache, 21W
Chipset
Intel® i855 chipset consisting of: • 82855GME Graphics/Memory Controller Hub (GMCH) - Montara • 82801D I/O Controller Hub (ICH4) • 82802 Compatible Firmware Hub (FWH)
Memory
• •
200-pin SO-DIMM socket (notebook style module), PC2100/2700 DDR266/333SDRAM, 1GB maximum USB FLASH drive on-board (option), up to 2GByte bootable NAND Flash with USB2.0 controller
Video
Analog monitor and digital flat-panel display support by DVI-I connector (front panel), up to 2048x1536 pixel 16M colours @75Hz refresh rate (analog), up to 1600 x 1200 pixel 16M colours @60Hz (digital), incorporates PanelLink Digital technology (Silicon Image). Front panel option: D-Sub (female HD15) VGA connector available, replaces DVI-I connector
USB
All ports over-current protected, data transfer rate of up to 480Mbps, conforming to USB2.0 • USB port 1-2: Type A connector (front panel) • USB port 6: Expansion interface option (CCA-LAMBADA mezzanine companion board) • USB port 3-5: J4/P4 Rear I/O option (CDY-RIO rear I/O transition module) • USB port 4 dedicated to the optional on-board USB Flash drive
Ethernet
• • • • •
IDE/ATA (Parallel)
• Ultra ATA/100 connector (Secondary IDE), handover to CCA-LAMBADA mezzanine expansion board with CCA on-board hard disk drive or external device • CompactFlash socket (mezzanine module) for CFA ATA cards (Secondary IDE) • J4/P4 Rear I/O option: Primary IDE accessible from CDY-RIO rear I/O transition module • CD2 on-board hard disk drive module option (Primary IDE)
Serial ATA
On-board dual port Serial ATA controller, ports available across J5/P5 on CDY-RIO rear I/O module (alternatively accessible via Serial ATA connectors on board), RAID and non-RAID drivers available
FLASH Drive
Optional on-board USB2.0 FLASH drive controller and 2 pcs. NAND FLASH up to 8Gbit each (total memory capacity up to 2GByte), can be configured as bootable disk, data transfer rates up to 18MB/s for read, 13MB/s for write (dual channel mode)
Mezzanine Facility
Optional usage of either • 1 Slot for a PMC module, I/O from the front panel and across J5 • On-board 2.5-inch hard disk module (Primary IDE)
Expansion Interface
• On-board LPC/USB/AC97 Super-I/O, USB and audio expansion interface connector • Suitable CCA-LAMBADA 3U mezzanine companion board available
3 x 10/100/1000Mbps Gigabit Ethernet controllers (82541ER) Jumbo Frame support up to 16KB 1 x 10/100Mbps Fast Ethernet Controller (82562) 1 x Gigabit and Fast Ethernet accessible via RJ45 jacks from the front panel 2 x Gigabit Ethernet as rear I/O according to PICMG® 2.16 across J3 (alternatively accessible via RJ45 jacks from the CDY-RIO back panel)
-2EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU Feature Summary CD2-BEBOP Rear I/O
• • • • • • •
2 x Gigabit Ethernet (J3) 2 x Serial ATA (J3) Primary IDE (J4) 2 x USB (J4) LPT, COM, GPIO (J4) PMC mezzanine rear I/O (J5) Suitable rear I/O transition module CDY-RIO available
CompactPCI®
32-bit PCI bridge chip PLX PCI 6150 (HB4), 133MBps CPCI master, transparent mode (CPCI system slot operation). When using the CD2-BEBOP on a peripheral slot the PCI bridge must be removed (special board versions available on request)
Hot Swap Function
Board hot insertion/extraction without adversely effecting a running system, 'Basic Hot Swap' implementation according to CompactPCI Hot Swap Specification PICMG® 2.1. In order to use the CD2-BEBOP as a peripheral slot board, the local PCI bridge must be removed (stand-alone operation or PICMG 2.16 communications path required instead of PCI bus data exchange), special board versions are available on request
PICMG® 2.16
Dual Link Port Node, complies with the PICMG® 2.16 CompactPCI® Packet Switching Backplane Specification
BIOS
Phoenix BIOS
Typical Power Consumption
• +5V +0.25V/-0.15V tbd A max. • +3.3V +0.17V/-0.1V tbd A max.
Thermal Conditions Environmental Conditions
• • • • • •
EC Regulations
EN55022, EN55024, EN60950-1 (UL60950-1/IEC60950-1)
Operating temperature: 0°C ... +70°C (CPU dependent) Storage temperature: -40°C ... +85°C, max. gradient 5°C/min Humidity 5% ... 95% RH non condensing Altitude -300m ... +3000m Shock 15g 0.33ms, 6g 6ms Vibration 1g 5-2000Hz
Board
Processor
CPU/MEM Score
CD2-1X-BEBOP
1.4GHz LV Pentium® M (Dothan 738)
4745/8489
CD2-2X-BEBOP
1.8GHz Pentium® M (Dothan 745)
6100/10441
CD2-3X-BEBOP
2.0GHz Pentium® M (Dothan 755)
6773/11398
Performance Rating Measured with PCMark2002 under Windows XP, 512MB PC2700 DDR MTBF
tbd h
subject to change
-3EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU
CD2-BEBOP with DE2-TIGER PMC Module
CD2-BEBOB with on-Board CompactFlash Module & DB1-FALCON PMC Module
-4EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU
CD2-BEBOP with 2.5-Inch Hard Disk Module on-Board
CD2-BEBOB with on-Board 1.8-Inch Hard Disk
-5EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU Block Diagram CD2-BEBOP 1/2
Block Diagram CD2-BEBOP Sheet 1/2
Hub Link
J4
82 82 802 FWH 802 BIOS
LPC
82 562
6150
82 541
PCI to PCI Bridge
Sheet 2
GMCH ICH4 ICH4
VGA USB PIDE COM
KB MS
PS/2
Super I/O 8761
GPIO PS/2
CompactPCI
10/100/1000
Front Panel I/O
ETH
1GB (max) DDR SO-DIMM
AC'97
C10-CFA CompactFlash ATA
LPC
Expansion I/F
USB
CompactPCI
Ethernet Controller
SIDE
ICH4
J1
J2
CompactPCI
10/100
Sheet 2
USB
LCI ETH
J4
PIDE USB
Opt. CCA-LAMBADA Expansion Board
VGA D-SUB
Sheet 2
J4
512MB/1GB PC2100/2700
GMCH 855GME
RGB
VGA
DDR-SDRAM
DVO
IDE I/F
Panel Link
DVI
Local PCI
DVI-I
Digital/Analog
FSB 400MHz
J4
-6EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU Block Diagram CD2-BEBOP 2/2
82 541
ETH
Gigabit Ethernet 10/100/1000 Controller
PICMG 2.16 ETH
Serial ATA Controller
35 12
J3
SATA-1 SATA-0
Dual SATA
PMC Rear I/O
J5
PCI
1
2
PMC Mezzanine 4
PIDE
C11-HDD 2.5-" HD Module
UT 168
up to
USB4
Sheet 1
2GBytes NAND Flash
1 x PMC Module or 1 x 2.5-" Hard Disk Module
Sheet 1
FLASH Drive Option
Basic Hot Swap Controller PICMG 2.1
Local Power
CompactPCI
Front Panel I/O
Local PCI
82 541
CompactPCI
Sheet 1 Block Diagram CD2-BEBOP Sheet 2/2
16 46
CPCI Power
-7EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU Orientation of Connectors CD2-BEBOP
JRTC
SATA CON1 SATA CON2
JRST
1
1
1
MJ1
SATA
2
1
2
1
2
MJ2
USB4 Flashdrive
PMC Mezzanine
PS2
541
541
ETH Expansion Module
ATA / IDE Module
USB2
1
1
USB1
LPC / AC’97
855 GMCH
Reset
GETH ICH4
Pentium M
541
DVI-I
CompactFlash / 1.8-Inch Hard Disk Option VGA
DDR SOReset-DIMM 200
-8EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CompactPCI J4
MJ4
CompactPCI J5
JFD
CD2-BEBOP • CompactPCI Pentium® M CPU Front Panel I/O Functions CD2-BEBOP
CD2BEBOP
P M C M E Z Z A N I N E
ETH3
K B / M S
E T H 2
ETH4
USB G P
I D E
PWR/RES
H S
ETH1
D V I
-9EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU
CD2-BEBOB with CDY-RIO (Rear I/O Transition Module Option)
CDY-RIO Rear I/O Module
- 10 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU
PMC Rear I/O
J5
Mezzanine I/O
SA
optional PMC back panel adapter
SATA
P-SA2
SATA
Serial ATA
PMC
CompactPCI
CDY-RIO Block Diagram 1/2
P-PMC
CD2-BEBOP Rear I/O
Block Diagram CDY-RIO
USB5 LM 35 26
USB3
COM
SA
CU
COM (TTL)
ADM COM (RS-232) 211
P-SA1 JMP-COM
GPIO
P-GPIO
PS/2
KB MS
VGA IDE
BCT 16 245
CompactPCI
JMP-IDE
J3
P-IDE1
IDE 44
IDE 40
P-IDE2 C00-HD (optional)
Back Panel I/O
VGA
J4
USB
GPIO
CompactPCI
P-CU
ETH 10/100/1000Mbps Ethernet (J3 Option)
ETH 6U 4/8HP
- 11 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU CDY-RIO Block Diagram 2/2
Block Diagram C00-HD
CDY-RIO
IDE 44
P-IDE5
IDE 44
P-IDE3
IDE 44
P-IDE4
2.5-" Hard Disk
CDY-RIO Back Panel I/O
2.5" Hard Disk
6U 8HP
- 12 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU Back Panel CDY-RIO
M E Z Z A N I N E CDYRIO U S B SATA S 1
S 2
U S B
C O M
K B / M S
8HP Panel Width w Option C00-HD
M S
V G A
E T H 2
E T H 3
- 13 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU Ordering Information Alias
Ordering No.
Short Description
BEBOP
CD2-1A-BEBOP
6U, LV Pentium M 1.4GHz 738, 512MB DDR SDRAM, 6 x USB, 4 x Ethernet (3 x GB), PICMG 2.16 Dual Link, IDE, SATA, CompactFlash ATA slot, 1 x PMC mezzanine, DVI-I video, rear I/O, on-board USB Flash drive
BEBOP
CD2-1B-BEBOP
similar to CD2-1A-BEBOP, w/o on-board USB Flash drive
BEBOP
CD2-1C-BEBOP
similar to CD2-1A-BEBOP, w/o on-board USB Flash drive, w/o 2.16 rear I/O Ethernet
BEBOP
CD2-1H-BEBOP
similar to CD2-1A-BEBOB, on-board 2.5-inch hard disk mezzanine module (replaces PMC slot)
BEBOP
CD2-2A-BEBOP
6U, Pentium M 1.8GHz 745, 512MB DDR SDRAM, 6 x USB, 4 x Ethernet (3 x GB), PICMG 2.16 Dual Link, IDE, SATA, CompactFlash ATA slot, 1 x PMC mezzanine, DVI-I video, rear I/O, on-board USB Flash drive
BEBOP
CD2-2B-BEBOP
similar to CD2-2A-BEBOP, w/o on-board USB Flash drive
BEBOP
CD2-2C-BEBOP
similar to CD2-2A-BEBOP, w/o on-board USB Flash drive, w/o 2.16 rear I/O Ethernet
BEBOP
CD2-2H-BEBOP
similar to CD2-2A-BEBOB, on-board 2.5-inch hard disk mezzanine module (replaces PMC slot)
BEBOP
CD2-3A-BEBOP
6U, Pentium M 2.0GHz 755, 512MB DDR SDRAM, 6 x USB, 4 x Ethernet (3 x GB), PICMG 2.16 Dual Link, IDE, SATA, CompactFlash ATA slot, 1 x PMC mezzanine, DVI-I video, rear I/O, on-board USB Flash drive
BEBOP
CD2-3B-BEBOP
similar to CD2-3A-BEBOP, w/o on-board USB Flash drive
BEBOP
CD2-3C-BEBOP
similar to CD2-3A-BEBOP, w/o on-board USB Flash drive, w/o 2.16 rear I/O Ethernet
BEBOP
CD2-3H-BEBOP
similar to CD2-3A-BEBOB, on-board 2.5-inch hard disk mezzanine module (replaces PMC slot)
BEBOP
CD2-H-BEBOP
On-board 1.8-inch hard disk module option, replaces CompactFlash socket adapter
BEBOP
CD2-Z-BEBOP
1GB Memory option
RIO
CDY-1-RIO
J3/J4/J5 rear I/O transition module 6U/4HP
RIO
CDY-2-RIO
J3/J4/J5 rear I/O transition module 6U/8HP with 2.5-inch rear I/O hard disk
LAMBADA
CCA-1-LAMBADA
3U mezzanine module, local expansion board complementing the CD2-BEBOP, front panel width 4HP, optional AC'97 codec
FALCON
DB1-1-FALCON
PMC module, USB2.0 host adapter
TIGER
DE2-2-TIGER
PMC module, SATA controller + 1.8-inch hard disk drive
280.7.400
External PS/2 keyboard/mouse Y-splitter-cable mini-DIN male to 2 x mini-DIN female
908.51.02.01
DVI-D to DVI-D cable assembly, 2m, connects the CD2-BEBOP to DVI monitors (digital way)
908.57.02.01
DVI-I to HD DSUB15 cable assembly, 2m, connects the CD2-BEBOP to VGA monitors (analog way)
908.57.12.01
DVI-I to VGA adapter (plug to receptacle), to be plugged onto the CD2-BEBOP DVI output, with HD DSUB15 socket, suitable especially for analog monitors with attached VGA cable
- 14 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU
Suitable 1U CPCI System Rack CR1
Suitable 7U CPCI System Rack CR7
- 15 EKF Elektronik GmbH • Philipp-Reis-Str. 4 • 59065 HAMM • Germany Tel. +49 (0)2381/6890-0 • Fax. +49 (0)2381/6890-90 • E-Mail
[email protected] • Internet www.ekf.com
CD2-BEBOP • CompactPCI Pentium® M CPU
DB1-FALCON Five-Port USB PMC Module
DE2-TIGER Quad-Port SATA RAID PMC Module
EKF Elektronik GmbH Philipp-Reis-Str. 4 59065 HAMM Germany
Fax. +49 (0)2381/6890-90 Tel. +49 (0)2381/6890-0 Internet www.ekf.com E-Mail
[email protected]
