Transcript
Ronda AG
30 9 6
10
www.ronda-startech.com
1112 1 2 10 3 9 4 8 7 6 5
60
12
45
3
20
30
60
12
Cal. 5130.D
15
9
20
30
45
3 6
10
1112 1 2 10 3 9 4 8 7 6 5
21
01/2009
CH-4415 Lausen/Switzerland 21 15 30
Cal. 5130.B Battery type: 395 (diameter 9.5mm x 2.6mm / SR 927 SW) Accuracy: +20 / -10 seconds per month
English User’s Manual
In case your watch needs to be repaired or to raise claims under a guarantee, please contact the point of sales
Multifunction movement
Description of the display and control buttons Display elements
Control buttons
The alarm and chronograph are combined in Cal. 5130.D and 5130.B. All functions can be operated with the 2 push-buttons and crown.
Push-button A
Initial status (chronograph hands at zero position) – start the chronograph with push-button A – switch the alarm on and off with push-button B
Minute hand Date 5130.B
21
Hour hand
30
60
12 9
Hour and Minute counter
20
45
3 6
10
1112 1 2 10 3 9 4 8 7 6 5
Center stop-second
15
Crown
30
21
Chronograph active Push-button B is also operative for the chronograph as soon as timing is started with push-button A. At the end of timing and when the chronograph hands are reset to the zero positions the push-button functions once again assume their «initial status».
Push-button B
Alarm and reference time Second hand
The alarm cannot be adjusted when the chronograph is active.
Date 5130.D
Setting the date (quick mode)
Date 5130.B
31 30
60
12 9
20
45
3
10
6
1112 1 2 10 3 9 4 8 7 6 5
31
I
9
20
45
3
10
6
1112 1 2 10 3 9 4 8 7 6 5
Push the crown back into position I.
21 30
45
3
10
6
II
60
12 9
20
Setting the date too quickly in quick mode can result in the incorrect date being displayed. Switching the date between 01 and 31 (position II) restores the synchronisation.
30
Push-button A
Hour counter
1112 1 2 10 3 9 4 8 7 6 5
45
3
10
1112 1 2 10 3 9 4 8 7 6 5
15
Push-button B
21
Note The alarm cannot be used as long as the chronograph is in operation.
Chronograph: Intermediate or interval timing
Push-button A
21 30
60
12 9
45
3
10
6
1112 1 2 10 3 9 4 8 7 6 5
Example: Start: (start timing) Display interval: e.g. 10 minutes 10 seconds (timing continues in the background) * Making up the measured time: (the 3 chronograph hands are quickly advanced to the ongoing measured time). Stop: (Final time is displayed) Reset: The 3 chronograph hands are returned to their zero position
15 30
21
Minute counter
= 25 min 10 sec
Push-button B
(The accumulated measured time is shown)
21 30
60
12 9
Please note: 65,5% * Following , the accumulation of the 65,5% timing can be continued by pressing push-button A (Restart / Stop, Restart / Stop, …)
21
30
Push-button B
The three chronograph hands are returned to their zero positions.
30
Press push-button B. (The 3 chronograph hands will be reset to their zero positions).
15
* Stop: (e.g. 10 min 5 sec following )
60
12
6
45
10
1112 1 2 10 3 9 4 8 7 6 5
20
20
45
3
10
6
pushbutton A once more and read the 3 chronograph counters: 4h / 20 min / 38 sec
Zero positioning:
3 6
Reset:
30 9
9
20
Restart: (timing is resumed)
21
Stop: to stop the timing, press
21
60
12
Chronograph: Accumulated timing
30
21 30
Stop: (e.g. 15 min 5 sec following )
21
Example: Start: Press push-button A.
15
Minute counter
Example: Start: (start timing)
15 30
Minute counter
20
1112 1 2 10 3 9 4 8 7 6 5
Please note: The date of the following day must be set in the calendar changing phase between 9 PM and midnight.
I
10
date 01 appears.
15
01
6
Turn the crown until the correct
II
60
45
3
(Start / Stop / Reset)
60
12
20
30
01 12
30 9
Chronograph: Basic function
Push-button A
21
continues to run).
15
Date 5130.D
30
Hour counter
Pull out the crown to position II (the watch
65,5% = 40mm Druchmesser
15
Please note: = 21 Following , further intervals or inter= 40mm 40mm Druchmesser Druchmesser 65,5% = 40mm *Druchmesser 1112 1 2 10 3 9 4 8 7 6 5
30
mediates can be displayed by pressing 65,5%= 40mm Druchmesser push-button B (display interval / make up measured time, ...)
Push-button B
65,5% = 40mm Druchmesser Hour counter
Center stop-second
21
30
60
12 9
20
45
3 6
10
1112 1 2 10 3 9 4 8 7 6 5
15 30
21
I
II
III
Example: One or several chronograph hands are not in their correct zero positions and have65,5% to be adjusted (e.g. following a battery change).
21 30
45
3 6
10
1112 1 2 10 3 9 4 8 7 6 5
III
21
60 45
3
10
1112 1 2 10 3 9 4 8 7 6 5
15
17
I
III
17 / 1:25 AM 04 / 10:39 PM
60
12 9
10
1112 1 2 10 3 9 4 8 7 6 5
Turn the crown until yesterday’s date
03
45
3 6
continues to run).
Date 5130.D
45
3
10
1112 1 2 10 3 9 4 8 7 6 5
15 30
03
I
II
I
II
III
60 45
3 6
10
1112 1 2 10 3 9 4 8 7 6 5
Please note:
15
04
I
II
III
* Please observe the AM / PM clock rhythm.
Alarm time
12 9
20
45
3 6
Switching the alarm on / off 31
Activate the setting mode
Press the push-button for at least 2 seconds. As soon as the small minute hand jumps forward one minute, this mode is active.
60 10
1112 1 2 10 3 9 4 8 7 6 5
15 30
31
I
Alarm time
Push-button
30
Note The alarm cannot be used as long as the chronograph is in operation.
10
1112 1 2 10 3 9 4 8 7 6 5
Short pressing (less than 1 second): the alarm time is moved forward by the minute. Long pressing (longer than 2 seconds): the alarm time is moved forward until the push-button is released. Please note: If the push-button is not activated for 10 seconds, the setting mode of the alarm time deactivates itself. At the same time, two beeps are emitted to indicate that the alarm is switched on.
45
3 6
The alarm is switched on / off by briefly
60
12 9
20
Setting
pressing the push-button:
15 30
31
I
Alarm time
30
45
3 6
10
1112 1 2 10 3 9 4 8 7 6 5
15 30
04
I
II
III
Reference time
Small minute hand
60
12 9
20
45
3 6
10
1112 1 2 10 3 9 4 8 7 6 5
Reference time
15 30
04
I
II
30
III
45
3 6
10
1112 1 2 10 3 9 4 8 7 6 5
Press the push-button for at least 2 seconds. As soon as the small minute hand jumps forwards one minute, this mode is active.
(the display changes from reference time to alarm time). A signal indicates that the alarm is switched off.
60
12 9
20
Activating the setting mode
the reference time is moved forwards by the minute. Medium pressing: (1–2 seconds): the reference time is moved forwards by the hour. Long pressing (longer than 2 seconds): the reference time is moved forwards until the push-button is released.
* Push the crown back into position I
04 15 30
04
I
II
III
Alarm time
Short pressing (less than 1 second):
04 30
1 beep alarm switched off
Once the set alarm time has been reached, a signal is emitted for 20 seconds. This signal is repeated after two minutes. Following brief pressing of the push-button, the signal is immediately switched off.
(second hand stops. The display changes from alarm time to reference time.)
60
12 9
20
2 beeps alarm switched on
Please note: The alarm can be set maximum 12 hours before the desired alarm time.
* Pull out the crown to position III
Push-button
Setting the reference time 04
Resetting the time also requires the identical correction of the reference time. Please refer to «setting the reference time».
30
Setting the alarm time 31
current time 10:39 PM appears.
(the display changes from reference to alarm time.)
12
30
appears.
* Continue to turn the crown until the
Push the crown back into position I
30 9
20
III
Reference time
04
04
(the second hand stops. The display changes from alarm time to reference time.)
60
12
Turn the crown until the correct date 04
15 30
Reference time
appears 03 .
Pull out the crown to position III
30
04 30
Pull out the crown to position II (watch
II
Second hand
6
Example: – Date / time on the watch: – Present date / time:
20
30
Alarm time
9
III
Termination of the chronograph hands adjustment (can be carried out at any time. The display changes from reference to alarm time.)
Setting the time and date
12
20
II
Adjusting the hand and the hour counter hand (mechanical coupled) A 1 x short Single step Continuous A long
Crown
17 30
6
I
III
III minute III counter
Date 5130.B
9
Adjusting the next hand B
III position I Returning the crown to
simultaneously for at least 2 seconds (the center stop-second rotates by 360° corrective mode is activated).
15 30
Push-button B
20
III
Keep push-buttons A and B depressed
60
12
A
chronograph hands are in their correct or incorrect zero position. The display changes from alarm time to reference time.)
Push-button A
9
III III
B
= 40mm Druchmesser
Pull out the crown to position III (all 3
Minute counter
20
Adjusting the center stop-second A 65,5% = 40mm Druchmesser SingleDruchmesser step A 1 x short 65,5% = 40mm Continuous A long
Adjusting the chronograph hands to zero position
Please note: * In order to set the time to the exact second, must be pulled out when the second hand is in position «60» (III). Once the hour and minute hands have been set, must be pushed back into position I at the exact second.
What is the reference time? The current time is displayed by means of the hour and minute hand. Parallel to the current time, the reference time runs in the background: the alarm time refers itself to this reference time. Thus, resetting the time also requires the identical correction of the reference time. If the reference time is not synchronised with the current time, this results in the alarm signal being emitted at a different time to the set alarm time.
