Transcript
Product Specifications LNX LNX--8513DS 8513DS--VTM | LNX LNX--8513DS 8513DS--A1M
2-port sector antenna, 2x 698–896 MHz, 85° HPBW, RET compatible l
Fully compatible with Andrew remote electrical tilt system for greater OpEx savings
l
Excellent front-to-back ratio, USLS, VSWR, and PIM specifications to enhance network quality
l
Great solution to maximize network coverage and capacity
l
Extended elevation tilt for maximum flexibility in urban core areas
l
The RF connectors are designed for IP67 rating and the radome for IP56 rating
Electrical Specifications Frequency Band, MHz Gain, dBi Beamwidth, Horizontal, degrees Beamwidth, Vertical, degrees Beam Tilt, degrees USLS, typical, dB Front-to-Back Ratio at 180°, dB Isolation, dB VSWR | Return Loss, dB PIM, 3rd Order, 2 x 20 W, dBc Input Power per Port, maximum, watts Polarization Impedance
698–806 14.6 85 12.2 0–10 17 25 30
806–896 15.3 85 11.0 0–10 17 26 30
1.4 | 15.6
1.4 | 15.6
-153 400 ±45° 50 ohm
-153 400 ±45° 50 ohm
General Specifications Operating Frequency Band
698 – 896 MHz
Antenna Type
Sector
Band
Single band
Performance Note
Outdoor usage
Mechanical Specifications RF Connector Quantity, total
2
RF Connector Quantity, low band
2
RF Connector Interface
7-16 DIN Female
Color
Light gray
Grounding Type
RF connector inner conductor and body grounded to reflector and mounting bracket
Radiator Material
Aluminum
Radome Material
Fiberglass, UV resistant
RF Connector Location
Bottom
Wind Loading, frontal
618.0 N @ 150 km/h 138.9 lbf @ 150 km/h
Wind Loading, lateral
197.0 N @ 150 km/h 44.3 lbf @ 150 km/h
Wind Loading, rear
726.0 N @ 150 km/h 163.2 lbf @ 150 km/h
Wind Speed, maximum
241 km/h
|
150 mph
©2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: August 31, 2017
page 1 of 2 September 20, 2017
Product Specifications LNX LNX--8513DS 8513DS--VTM | LNX VTM | LNX--8513DS 8513DS--A1M
Dimensions Length
1847.0 mm
Width
301.0 mm
Depth
181.0 mm | 7.1 in
Net Weight, without mounting kit
17.8 kg
|
| |
72.7 in 11.9 in
39.2 lb
Remote Electrical Tilt (RET) Information Model with Factory Installed AISG 2.0 Actuator LNX-8513DS-A1M
Packed Dimensions Length
2283.0 mm
Width
463.0 mm
|
18.2 in
Depth
358.0 mm
|
14.1 in
Shipping Weight
29.8 kg
65.7 lb
|
|
89.9 in
Regulatory Compliance/Certifications Agency RoHS 2011/65/EU China RoHS SJ/T 11364-2006 ISO 9001:2008
Classification Compliant by Exemption Above Maximum Concentration Value (MCV) Designed, manufactured and/or distributed under this quality management system
Included Products BSAMNT-1 — Wide Profile Antenna Downtilt Mounting Kit for 2.4 - 4.5 in (60 - 115 mm) OD round members. Kit contains one scissor top bracket set and one bottom bracket set.
* Footnotes Performance Note
Severe environmental conditions may degrade optimum performance
©2017 CommScope, Inc. All rights reserved. All trademarks identified by ® or ™ are registered trademarks, respectively, of CommScope. All specifications are subject to change without notice. See www.commscope.com for the most current information. Revised: August 31, 2017
page 2 of 2 September 20, 2017
