Transcript
CARE + MAINTENANCE MELBOURNE 173-177 Barkly Avenue Burnley VIC 3121 P 03 9429 8888 F 03 9429 6966 SYDNEY PYD Building 197 Young Street Waterloo NSW 2017 P 02 8396 8700 F 02 9690 2804 BRISBANE 72–78 McLachlan Street Fortitude Valley QLD 4006 P 07 3251 4333 F 07 3257 2155 PERTH 153 Broadway Nedlands WA 6009 P 08 6389 1366 F 08 6389 1466 CONCEPT STORES Southern Innovations Canberra ACT P 02 6126 1155 F 02 6126 1156 Albury NSW P 02 6049 3322 F 02 6049 3323 Estilo Bathware & Ceramics Adelaide SA P 08 8415 2999 F 08 8415 2900 Vogue Spas & Bathrooms Southport QLD P 07 5528 0077 F 07 5528 0767 Gunns Kitchens & Bathrooms Launceston TAS P 03 6332 6201 F 03 6332 6299 Hobart TAS P 03 6272 6899 F 03 6272 9088
PROFILO
Profilo tapware uses 3/4 turn cartridges using the latest ceramic disc technology. All cartridges are guaranteed for 5 years against leaking.
Basin Set Assembly Installation
Maximum continuous working pressure is 800 kPa. For optimum performance a working pressure of 500 kPa is recommended. Excessive high pressure may void the manufacturers’ warranty. For Profilo spouts ensure the aerators are tightened and can not be removed by hand. Ensure all new installations are fully flushed prior to installing the ceramic cartridges, to prevent any posssible void of the warranty. All cartridges are recommended to be used with a maximum water temperature of 75˚C at the inlet of the cartridge. Excessive temperature may void the warranty. Avoid harsh chemicals and abrasive cloths. Clean using a soft soapy cloth and polish with a dry soft cloth.
WARRANTY › All Rogerseller, bathroom fittings and sanitaryware are covered by a five (5) year warranty from date of purchase.
› Rogerseller will undertake to repair or replace free of charge any faulty product, due to defects in materials or workmanship (within the period of the warranty).
› Rogerseller (or their nominated agent) reserve the right to assess, repair, replace or service any warranty claim as they see fit.
› This warranty excludes any defect or injury caused by or resulting from misuse, abuse or neglect, accidental damage, improper installation or other alterations or modifications which affect the reliability or performance of the unit not attributed to faulty manufacture. Exceptions:
› Flexible hoses covered by one (1) year warranty from date of purchase › Finishes - Satin finishes are covered by a one (1) year warranty against chipping, staining and flaking (excluding normal wear and tear).
The more stars the more water efficient
WATER RATING A joint government and industry program
Licence No. 0044
5
litres per minute When tested in accordance with Standard AS/NZS 6400
0409
www.waterrating.gov.au
PROFILO
Basin Set Assembly Installation
All lines must be fully flushed before installation of the ceramic cartridge. Failure to do so may void the manufacturers’ warranty.
For installations into an existing wall breech, ensure the seat of the tap is uniform, with no damage that may inhibit a positive seal with the ceramic cartridge. Only use a C-Tec seat refacing tool to recondition an existing tap seat.
1A. CERAMIC DISC CARTRIDGE
Screw the cartridge by itself into the tap body until it screws up against the seat of the tap. Ensure correct hot and cold cartridges are installed. 1B. TIGHTEN CERAMIC DISC CARTRIDGE
Using a 15mm spanner, do not use multi grips or adjustable wrench, grip the cartridge on its hexagonal flats and turn until the cartridge comes to a firm stop, no more than 1/8th of a turn. Do not overtighten past this point, the hex flats have been designed to burr off so as to prevent damage to the cartridge. 1C. FIBRE WASHER
Fit red fibre washer around cartridge and against the face of the tap body, then fit the Cartridge Lockout and screw it (by hand) onto the cartridge up to the face of the tap body. 1D. CARTRIDGE LOCKNUT
Fit the cartridge locknut using a spanner or where necessary a tube spanner (do not use multi grips) tighten the cartridge locknut with a similar force as would be used to tighten a traditional loose jumper valve bonnet and spindle assembly into a tap body. 2. NYLON WASHER / LOCKNUT
Locate the bottom locknut and a nylon washer onto the tap body. 3. TAP BODY
Insert the tap body up through the bench/basin hole. 4. BENCH LOCKNUT / BLACK NYLON WASHER
Fit a nylon washer and the bench locknut onto the cartridge locknut and tighten a few turns only. Note: It is important to position the bench lockout as high on the threaded cartridge lockout as possible. 5. BOTTOM LOCKNUT
Use the bottom locknut to pull the tap body tight against the bench. 6. O-RING / FLANGE
Ensuring the O-ring is located inside the flange, screw the flange to the bench lockout. Make sure the locking O-ring is attached to the protruding cylindrical part of the flange and is well greased with Magnalube teflon based lubricant. 7. NYLON INSERT
Checking that the pre-assembled nylon insert is screw fixed to the cartridge, adjust/test fit the handles to align as shown in Figure 2. Note: Before fitting make sure cartridge is set in ‘off’ position 8. TAP HANDLE
Press handle firmly into position until near flush with flange top (1mm gap). You should feel a ‘click’ fitting between the O-ring and the handle to signal successful locking of the assembly. NOTES
All lines must be fully flushed before installation of the ceramic cartridge. Failure to do so may void the manufacturers warranty.
35mm
Tap Handle
O-Ring
Flange
O-Ring
Bench Locknut
Black Nylon Washer
7.5mm (min) 30mm (max)
Figure 2. Handle Position Bloc series
Nylon Washer Locknut
Tap Body
