Programming Your Remote Control

Transcript

Programming Your Remote Control Programming Your Remote Control Program TV Button with Auto Search: • Start with the TV turned on. • Press and release the TV button . Program the Remote to the Set-Top box: • Press and hold the SETUP button  until it blinks twice and stays on. • Start with the TV turned on. • Look at the back of the remote and note • Press and release the POWER button . the number (1, 2 or 3). • While pointing the remote at the TV • On the Set-Top Box press and hold the press and release either the CH+ or CHOK button for approximately 5 seconds. (Channel) button  to begin searching for • Release the OK button. On the set-top box your TV’s code. display screen you should see RC REG. If RC REG is not shown on the display screen (In this search mode the TV button  will be on and blink every 5 seconds while the repeat and hold the OK button in longer. remote scans for the correct code). • On the remote control press and hold the STB button  4-5 seconds until it lights up. • If the TV turns off a working code has been found. Press the OK button y to store the • Press and release the STB button . (The code for the TV. The TV button will blink STB and AUX buttons will light up). twice. • Press the number that corresponds with the number on the back of the remote. Program TV Button with Auto Search: • Start with the TV turned on. • Press and release the TV button . Program the Remote to the Set-Top box: • Press and hold the SETUP button  until it blinks twice and stays on. • Start with the TV turned on. • Look at the back of the remote and note • Press and release the POWER button . the number (1, 2 or 3). • While pointing the remote at the TV • On the Set-Top Box press and hold the press and release either the CH+ or CHOK button for approximately 5 seconds. (Channel) button  to begin searching for • Release the OK button. On the set-top box your TV’s code. display screen you should see RC REG. If RC REG is not shown on the display screen (In this search mode the TV button  will be on and blink every 5 seconds while the repeat and hold the OK button in longer. remote scans for the correct code). • On the remote control press and hold the STB button  4-5 seconds until it lights up. • If the TV turns off a working code has been found. Press the OK button y to store the • Press and release the STB button . (The code for the TV. The TV button will blink STB and AUX buttons will light up). twice. • Press the number that corresponds with the number on the back of the remote. Notes: If you wait too long or you enter a number Program AUX Button with Auto Search: other than 1, 2 or 3, the STB button will turn off Program the remote to control another device and the registration process will terminate. Notes: If you wait too long or you enter a number Program AUX Button with Auto Search: other than 1, 2 or 3, the STB button will turn off Program the remote to control another device and the registration process will terminate. (VCR , DVD etc). • Start with the device turned on. • Press and release the AUX button .  SETUP Button • Press and hold the SETUP button  until it blinks twice and stays on.  POWER • Press and release the POWER button . Button • While pointing the remote at the device  Device press and release either the CH+ or CHButtons (Channel) button  to begin searching for STB Button your device’s code. TV Button AUX Button (In this search mode the AUX button  will be on and blink every 5 seconds while  CH (Channel) the remote scans for the correct code). +/- Button • If the device turns off a working code has been found. Press the OK button y to OK Button y store the code. The AUX button  will blink twice. Mount Horeb Office 437-5551 Dodgeville Office 930-9985 Tech Support: 1-800-843-5827 (VCR , DVD etc). • Start with the device turned on. • Press and release the AUX button .  SETUP Button • Press and hold the SETUP button  until it blinks twice and stays on.  POWER • Press and release the POWER button . Button • While pointing the remote at the device  Device press and release either the CH+ or CHButtons (Channel) button  to begin searching for STB Button your device’s code. TV Button AUX Button (In this search mode the AUX button  will be on and blink every 5 seconds while  CH (Channel) the remote scans for the correct code). +/- Button • If the device turns off a working code has been found. Press the OK button y to OK Button y store the code. The AUX button  will blink twice. Mount Horeb Office 437-5551 Dodgeville Office 930-9985 Tech Support: 1-800-843-5827