Transcript
PROJECTOR LIFT MODEL SI-200 INSTALLATION MANUAL T hank y ou for purchasing the new SI-200 P rojector Lift. T he SI-200 is supplied with a set of components and accessories that make it suitable for installation for the majority of standard AV applications, but note must be made of the restrictions that apply to the weight capability of this unit and not exceeded. P rojector lift S I-200 MUST B E INSTA LLED BY SPECIA LIZED PERSONNEL O NLY . B efore installing the projector lift, please r ead the following instr uctions carefully : - The projector lift must be used INDOORS O NLY. - IT IS FORBIDDEN TO STA Y UNDER THE LIFT. - NEVER CO NNECT MORE THA N ONE LIFT MOTOR TO THE SA ME SWITCHER. Use the supplied switcher only . - IN CA SE OF MA INTENA NC E, UNPL UG THE PO WER SUPPLY. - In case the lift is controlled v ia relais, take care that the control sy stem is pr ogrammed so there is no tension on the relais for at least 1 sec. during switching between r olling up and r olling down operations and viceversa. - P lease confir m that your pr ojected image width will fit your screen from y our proposed mounting location prior to installation. - Incorr ect use of the lift, including exceeding the maximum lifting weight, would be dangerous and invalidate the warranty. - The manufacturer does not take responsibility for any damage to property or - per sonal injury , if the lift is used outside of recommended specifications. - This product uses a 230V A C Motor. DO NOT attempt to serv ice the motor. - Incorr ect servicing could lead to risk of electric shock. - F or any r epair ing, please contact directly the dealer y ou purchased the unit fr om. - C heck at least once a y ear that the screws of the steel cables are well tightened and that the steel cables are in good conditions. In case they hav e signs of usage or damages, replace them pr omptly with the or iginal ones supplied by the manufacturer .
SUPPLIED EQUIPMENT LIST W hen you open the packaging, please C HEC K that it contains A LL the components below. In case one or more components are missed, please refer to the dealer y ou purchased the product from. A ) 1 MEC HANIC PRO JECTO R LIFT SUPPLIED W ITH A CABLE C HAIN AND MO TO R W ITH A 3 METER CA BLE WITH FO UR ELEC TRIC W IRES ( UP, DOWN, NEUTRA L A ND EARTH) B) 4 “L” FO RM ALUMINIUM BRACKETS FO R C EILING MOUNTING C ) O N/OFF SWITC H UNIT D) INSTRUC TIONS FO R ELEC TRICA L CONNEC TIONS BETW EEN MO TO R AND SWITCHER E) 4 THREADED BA RS M6 L. 25 CM F) 8 HEXA GONAL SC REWS 6x14 MM. G) 12 NUTS M6 FO R MOUNTING THE THREA DED BA RS TO THE FA LSE C EILING PLA TE AND TO THE LIFT H) 4 SLIDING BRAC KETS TO SUPPO RT THE FA LSE C EILING PLA TE I) 4 HEX HEA D SC REW S 6X10 MM. FO R FIXING THE SLIDING BRAC KETS TO THE LIFT FRA ME J) 4 BLIND SC REW S M6 A ND 4 BUSHES M6 FO R FIXING THE FALSE C EILING PLATE TO THE THREADED BA RS INST A LLAT ION INST RUCT IONS Use the hexagonal screws listed as “F” in the equipment list, to mount the “L” brack ets to the profile of the lift, as shown in PICTURES 1A , 1B and 1C below:
PICTURE 1A
PICT URE 1B
PICT URE 1C
1
Mount the lift to the ceiling using the suitable bolts/ screws (NO T SUPPLIED) and verify that the projector lift is perfectly horizontal using a sprit lev el. Use shims to lev el the lift, if required, between the brack ets and ceiling. Installing the lift perfectly lev el is IMPO RTA NT and ensures silent mov ement of the lift without any shak ing, jolting or friction that would compromise the alignment between projector and projection screen. O nce you hav e mounted the lift, position the projector either on or under the grill using the screws indicated in the instruction manual of your projector, as shown on PICTURES 2A , 2B and 2C .
PICT URE 2A
PICT URE 2B
PICT URE 2C
Connect the projector lift to the electricity supply as explained on the attached instructions for electrical connections (PICTURE 2D). The next step is to set the “UPPER END STO P POSITIO N” (C LO SED lift) and the “LOW ER END STOP PO SITIO N” (OPEN lift). The “LOWER END STOP POSITION” has to be regulated so that the image is correctly projected onto the screen. In order to fix the “UPPER END PO SITIO N”: WARNING: in case the installer needs to modify this endstop, it is allowed to lower the closed stop position. Do not try to high the upper end-stop beca use this will cause severe damages to the product a nd invalida te warranty on the lift. -
Turn the screw on the motor shown on the picture, clockwise to lower the lift.
In order to fix the “LOWER END STOP POSITION”: - Turn the screw on the motor, as shown on the picture, anticlockwise to increase the bottom stop point and clockwise to reduce it.
PICT URE 2D
2
O nce you hav e fixed the “UPPER END STOP PO SITIO N”, mount the four sliding brack ets with their screws under the lift frame ( see PIC TURE 3A ). If necessary , the four sliding brack ets can be angled in the desired direction. If necessary , cut the threaded bars to the desired length. Mount the bars to the sliding brack ets using the supplied nuts as shown in PIC TURE 3B. O n the false ceiling plate (not supplied), fix in the right position the four blind screws or the four bushes prov ided (point J of the supplied equipment list). A t this point, fix the false ceiling plate to the four threaded bars (see PICTURE 3C)
PICT URE 3A
PICT URE 3B
PICTURE 3C
If the lift does not line up horizontally to the false ceiling, modify the length of the bars or the “UPPER END STO P POSITION”, following the instructions above described. The signal and power cables should run inside the cable management sy stem supplied. The SI-200 is supplied with an articulated chain; once you hav e put signal and power cables inside the cable management sy stem, check carefully that the “L” profiles on the front and on the rear side of the grill are well-positioned and that they ensure the best descent and rise of the cable management sy stem. Please, be sure that the articulated chain is torsion free. A torsion of the chain will produce its coming out or its side wrong mov ement. O pen the sleepers that form the link s of the chain and place the cables inside as shown below. (Pictures 4A and 4B )
PICTURE 4A
PICT URE 4B
3
TECHNICAL SPECIFICATIONS POWER SUPPLY
230 V 50 Hz
MAX CONSUMPT ION
156 W
TORQUE
10 Nm
MOTOR SPEED
17 Rpm
DIMENSIONS LIFT CLOSED
576X230X555 mm. (WxHxD)
DIMENSIONS LIFT OPENED
576X1960X555 mm. (W xHxD)
GRILLE T OTAL DIMENSIONS
410x450 mm. (W xD)
MAXIMUM SIZE FIXING POINTS PROJECTOR
320x350 mm. (W xD)
MAXIMUM LOAD
15 KG.
NET WEIGHT OF PROJECT OR LIFT
15 KG.
CABLE GATHERING SY STEM
20x18 mm. (WxH)
TECHNICAL DRAWINGS
C LO SED LIFT: FRONTA L VIEW
O PEN LIFT: SIDE VIEW
C LOSED LIFT: SIDE VIEW
4
