Transcript
Datasheet
NV-ET1801 TBus® SINGLE PORT PoE+ TRANSMITTER
Description
The NVT Model NV-ET1801 TBus PoE+ Transmitter is a compact bus-architected media converter that delivers 10/100 BaseT Ethernet and PoE+ power via coax, UTP or 2-Wire or Shielded Twisted Pair cable. These transmitters are extremely simple to use, with no IP or MAC addressing required. Status LEDs indicate power and link connectivity/quality/activity for RJ45 and TBus ports.
Features
• Transmit 10/100/PoE+ BaseT, over Coax 8,000ft* over RG-59U; 2,000ft over 2-Wire/UTP; 1,300ft over Shielded Twisted-Pair* • Use with the NV-ER1804 (4-Port)
• Powers PoE, PoE+, or High Power PoE cameras (or other PoE devices), up to 50 watt • Easy configuration, no PC required
The NV-ET1801 TBus Ethernet Transmitter is backed by NVT’s award winning customer support, Limited Lifetime Warranty and advance replacement.
• Transparently supports all networking protocols (UDP, TCP/IP, HTTP, Multicast etc.)
• Advanced 128-bit AES encrypted transmission and PoE+ power technology
* Distance and number of devices supported may be lower due to power supply capacity and wire voltage-drop. See wire distance chart on page 4. Aggregate TBus bandwidth is dynamically allocated (shared based on traffic), and decreases with wire distance. High bandwidth streaming devices (>15Mbps) that employ unusually “chatty” protocols (TCP/IP, TFTP, etc.) are not recommended. Use RTP/UDP instead.
• Built-in transient protection; industrial temperature range • Limited lifetime warranty
Typical Application
IP Camera
Cat5 ≤328ft (≤100m)
NV-ET1801
any wire
NV-ET1801 or NV-ER1804
Cat5 ≤328ft (≤100m) 56VDC Power Supply
Network Video Technologies (+1) 650.462.8100 • US +44 (0) 20.8977.6614 • UK www.nvt.com •
[email protected] 1 of 4
Switch or Router
Hybrid DVR or NVR LAN / WAN
Monitor
NV-ET1801 TECHNICAL SPECIFICATIONS
Datasheet MECHANICAL / ENVIRONMENTAL
RJ45 ETHERNET INTERFACE Connectivity: PoE Power:
This Power Sourcing Equipment (PSE) detects and supports Powered Devices (PDs) that are compatible with IEEE 802.3af or 802.3at, or PDs that draw up to 50 watts. For maximum power distance, 56VDC appears on all eight RJ45 pins*.
Protection:
Product weight: Packaged weight:
Cat5 or better
Distance:
TBus LINK INTERFACE Connectivity:
Topology:
Bus architecture supports star, daisy-chain, or an combination. One control-room Receiver may support multiple remote TBus Transmitters.
Latency:
Wire distance: Encryption:
Model NV-PS56-60W:
3 mS
IEEE 1901
Model NV-PS56-90W:
Up to 8,000 feet, 1.5 miles (2.5km)*
128-bit AES, through one-button joining
*IMPORTANT NOTE: Data rate, distance, and number of devices may be lower due to wire voltage-drop, power supply capacity, or signal attenuation. See page 4.
Data
Link Quality
Link
Green = PoE device connected
Flashes with Data
Green = good Amber = fair Red = poor
Remote device detected
5x20μS 3000A, 6000V ESD 20KV, 200pF
Use only the power cord provided with the unit or equivalent UL approved type SPT-2, SVT, or SJT 18/3 AWG 100~240 VAC, 1 Amp 60°C max 15ft (4.5m) long. One end with IEC380-C13 appliance coupler and the other end with NEMA 1015P or equivalent for your country. REGULATORY UL Listed to IEC/UL 60950-1 Complies with FCC part 15A limits
56VDC
WARRANTY Limited Lifetime
PoE
56V 90W 5.77in (147mm) long 2.36in (60mm) wide 1.27in (32mm) high, 0.94lb (430g)
Transient Immunity:
LED STATUS INDICATORS
No Ethernet No Analog
56V 60W 4.90in (124mm) long 2.00in (51mm) wide 1.25in (32mm) high, 0.67lbs (300g)
Operating / storage temperature: -40°F to +185°F (-40°C to +85°C) 20 to 5% relative humidity non-condensing
WARNING: For safety, never use more than two power supplies within a TBus channel. Never use more than one 60 watt remote power supply on each TBus channel.
10/100 PoE+
5 x 20μS 3,000A, 6,000V ESD 20KV, 200pF
POWER SUPPLY Power is usually supplied by the TBus Receiver. For optional supplemental local power, an additional class 2 power supply may be purchased. These supplies are external inline, with an IEC380-C14 power inlet and a 6ft (1.18m) line cord. Input voltage is 100~240VAC 50/60Hz. A molded P1J 5.5mm barrel connector provides a class 2 (SELV) regulated output.
150 Mbps total network bandwidth* with dynamic bandwidth allocation
Transmission technology:
10 BTU/hour
Transient immunity:
25 to 100 Ω
Data throughput:
≤ 3W
Generated heat:
BNC or RJ45
Coax, single- or multi-pair UTP, 18/2, or STP wire
0.36lb (0.16kg) 0.46lb (0.21kg)
Power consumption:
up to 328 feet (100m)
Wire type:
3.23in (82mm) wide 0.93in (24mm) high 4.8in (122mm) deep excluding connectors
Operating / storage temperature: -40°F to 185°F (-40°C to +85°C) 20 to 85% relative humidity non-condensing
Industrial transient protection Thermistor current protection
Wire type:
Impedance:
Body Dimensions:
10/100/1000 BaseT IEEE 802.3ab auto-negotiation, auto MDI / MDX crossover
Specifications subject to change without notice.
Power Flashes when initializing or Joining
2 of 4
NV-ET1801 PRODUCT AND ACCESSORIES
NV-ET1801: Single port transceiver only
10 /10 0
Datasheet
Po E+ No E
the rne t,
No
An a
log
56 V
DC
NV-PS56-60W: 56VDC power supply, 60 watts with IEC line cord
NV-PS56-90W: 56VDC power supply, 90 watts with IEC line cord
NV-BNCT:
BNC “T” adaptor
NV-EC4BNC:
1:4 BNC splitter adaptor
NV-BNCA:
BNC to 2-Wire Adaptor
NV-RJ45A:
RJ45 to Screw Terminal Adaptor
NV-PC4PR:
RJ45 Patch Cord, 4-pair 3’ (1m)
3 of 4
NV-ET1801 POWER DATA DISTANCE
Datasheet ● Start with the camera wattage at the left. Sometimes IP cameras are listed as to their PoE Class rather than wattage.
The distance capability of wire is dependant on its ability to deliver DC power, and separately, to deliver high-frequency data signals.
● Now read over to the right until you find your kind of wire. Then look up (feet) or down (meters) to find your maximum distance.
The graph below shows maximum power delivery when using a 56V power supply. If you are locally powering your camera (or other remote device), then this graph does not apply.
● If your wire is not among the examples, simply measure its total resistance and find the value on the right side of the graph. The maximum supported wattage is on the left.
A Distance Calculator can be found at www.nvt.com.
● There are a wide variety of wire qualities, from copper-plated steel at the low end (CATV wire) to high performance low-loss pure copper.
PoE devices require a minimum of 43V to operate. With a 56V supply, we have up to 13V of allowable voltage drop on the wire. The voltage will dip in proportion to the remote (camera) load. The graph below shows what PoE power distances are supported for various loads and wire types.
Power Data Distance 16,400 ft
13,120 ft
9,840 ft 8,200 ft 6,560 ft 5,904 ft 4,920 ft
3,936 ft 3,280 ft
2,624 ft
1,968 ft 1,640 ft
11
14
12 Ω 14 Ω
AW
G
6 18
G
19 Ω 21 Ω
22
AW
/U
20
AW
/U
59
G
AW
23 Ω
G
PoE Class PoE C 2
16 Ω
TV CA
24 Ω 20 G AW
0W
38 Ω 5,000 m
4,000 m
3,000 m 2,500 m 2,000 m
800 m
600 m 500 m
400 m
300 m 250 m 200 m 180 m 150 m
120 m 100 m
80 m
60 m 50 m
40 m
30 m
Network Video Technologies (+1) 650.462.8100 • US +44 (0) 20.8977.6614 • UK www.nvt.com •
[email protected]
28 Ω
Data Limited
TV CA
G AW 22
PoE Class PoE C 1
Total Wire Resistance
11 Ω
RG
RG
59
RG
PoE Class PoE C 3
RG
r 1P
Data Limited
r 1P
3.0 W 2.5 W 2.0 W
G
4.0 W
AW
G AW 24
6.0 W 5.0 W
6Ω 7Ω 9Ω
Ca t5 4P r
23
t5 Ca
PoE Class PoE C 4
12 W 10 W 8.0 W
4Ω
Pr
High High hP Power ower we t6 Ca
Camera Wattage
W W W W W
3Ω
Ca t6 4 18 /2
40 W 30 25 20 18 15
1,312 ft
984 ft 820 ft 656 ft 590 ft 492 ft
397 ft 328 ft
262 ft
197 ft 164 ft
131 ft
98 ft 50 W
Copyright 2014 NVT, Inc. 411-1801-1-A3 4 of 4