Transcript
_
V1.9
Adapters
QFP100 - TET Target CPU package: QFP100 Body size: 14 mm x 14 mm Pitch: 0.5 mm POD target layout: T_QFP100S Can be used with: • 78K0R/Fx3 ActiveGT POD • MPC5604P Active GT POD • MPC5604B Active GT POD • SPC56AP Active GT POD • NEC V850ES/Fx2 ActivePRO POD • NEC V850ES/Sx2 ActivePRO POD • NEC B850E/CG3 ActivePRO POD • NEC B850E/CG4 ActivePRO POD • NEC V850ES/GB1 ActivePOD • TMS470Pxx_3v3 Standard ActivePRO POD • TMS470R1VB8x SE4 ActivePRO POD • TMS470R1VB8 Standard ActivePRO POD • TMS470R1VB8 I/O Extended ActivePRO POD • 68HC08AZ POD • MC68LC302 POD • MC68LC302 Active POD Note that adapter solutions stated in the document can be used only with listed PODs. Disregarding this warning may result in hardware failure of the target and the emulation system.
Available Adapter Parts (by ordering code): •
IA100TQ-SOLDER
Solder part, which is being soldered to the target.
iSYSTEM, August 2012
1/8
(Unit: mm) A B 16.5 1.125
C 17.0
D 17.0
E 2.15
K 19.55
L 19.55
Recommended (by TET) PCB footprint size
IA100TQ-SOLDER dimensions •
IA100TQ-WIRE
The IA100TQ-WIRE represents flexible connection between the POD and the target.
iSYSTEM, August 2012
2/8
•
IA100TQ-FIXED
The IA100TQ-FIXED represents fixed inflexible connection between the POD and the target.
•
IA100TQ-CPU
The IA100TQ-CPU is used to connect the CPU directly to the target. Above picture does not show exactly the IA100TQ-CPU but IA144TQ-CPU which looks exactly the same considering that it has different pin count. •
IA100TQEXT-CAB
The IA100TQEXT-CAB is a 30 mm extension and can be used to extend the adapter. When used, it is connected on top of the IA100TQ-SOLDER.
iSYSTEM, August 2012
3/8
Flexible Adapter IA100TQ-WIRE and IA100TQ-SOLDER are essential parts required to adapt the POD to the target QFP100 package. First, IA100TQ-SOLDER is soldered to the target and then the POD is connected via IA100TQ-WIRE.
Assembly Pay attention to pin 1 while assembling the adapter and connecting the POD to the target. Improper use of the adapter or even incorrect adapter used with your particular POD can damage the emulation system and the target. 1. First, solder IA100TQ-SOLDER to the target PCB. 2. Next, connect the IA100TQ-WIRE to the POD. 3. Finally, connect the POD via IA100TQ-WIRE to the target. Precaution must be taken after the POD is connected to the target. Adapter parts may break due to the user carelessness.
iSYSTEM, August 2012
4/8
Fixed Adapter IA100TQ-FIXED and IA100TQ-SOLDER are essential parts required to adapt the POD to the target QFP100 package. First, IA100TQ-SOLDER is soldered to the target and then the POD is connected via IA100TQ-FIXED. A flexible adapter is recommended to be used with Active or ActivePRO POD since the parts of fixed adapter solution can easily break due to the Active and ActivePRO POD size and weight. Assembly Pay attention to pin 1 while assembling the adapter and connecting the POD to the target. Improper use of the adapter or even incorrect adapter used with your particular POD can damage the emulation system and the target. Phase 1: Solder IA100TQ-SOLDER to the target PCB.
Phase 2: Connect IA100TQ-FIXED to the POD.
If optionally IA100TQEXT-CAB is used, it must be connected to IA100TQ-FIXED now.
iSYSTEM, August 2012
5/8
Phase 3: Connect the POD to the target via IA100TQ-FIXED.
Precaution must be taken after the POD is connected to the target. Adapter parts may break due to the user carelessness.
iSYSTEM, August 2012
6/8
Dimensions (Unit : mm) Fixed Adapter - QFP100
iSYSTEM, August 2012
A 46 x 46
B 10 x 10
D 10
E 11
7/8
Connecting the CPU directly to the target The CPU can be connected directly to the target using the IA100TQ-SOLDER in combination with the IA100TQ-CPU. This solution is very suitable for an ultimate test. Step 1: Solder the IA100TQ-SOLDER to the target PCB.
Step 2: Insert the CPU into the IA100TQ-CPU, which then connects to the IA100TQ-SOLDER.
Disclaimer: iSYSTEM assumes no responsibility for any errors which may appear in this document, reserves the right to change devices or specifications detailed herein at any time without notice, and does not make any commitment to update the information herein. iSYSTEM. All rights reserved. iSYSTEM, August 2012
8/8
