Transcript
QorIQ Qonverge Platform
QorIQ Qonverge B4860QDS Application Development System For applications using the QorIQ Qonverge B4860 baseband SoC Overview The QorIQ Qonverge B4860QDS development system is a complete application development environment intended for engineers developing applications for the Freescale B4860 baseband SoC processor. The B4860 processor includes highly integrated MPU and DSP processor cores containing four e6500 dual-thread Power Architecture® cores, including the AltiVec 128-bit Vector SIMD engine running at up to 1.8 GHz, six StarCore SC3900FP DSPs supporting up to 230.4 GMAC/s of fixed point and up to 115.2 GFLOP/s of floating point with each DSP core running at 1.2 GHz, powerful baseband and transport accelerators and high-speed interfaces pertinent to the device high throughputs. This device targets high-bandwidth, highly computational baseband applications such as multicarrier, multisector LTE (FDD and TDD), LTE-Advanced, WCDMA/HSPA+, TD-SCDMA, GSM and WiMAX base station applications. The B4860QDS is intended to serve as a platform for software and hardware development in an environment using the B4860 processor.
QorIQ Qonverge B4860QDS Board Block Diagram QorIQ Qonverge B4860QDS Board 25 M
25 M
I2C_CH0
SPD1
Prom Jet NOR Flash Boot On Socket
FPGA IFC Module
DMX Master
NAND Flash Boot
DDR3 DDR3 DDR3 DDR3 DDR3 x16 x16 x16 x16 x16 DDR3 DDR3 DDR3 DDR3 DDR3 x16 x16 x16 x16 x16
SERDES2 FER CLK 66.7 M 133 M
1866 M @ 4 GB in Two Ranks @ 64+ECC 122.88 M/125 M/ 156.25 M DDR-1 122.88 M IFC 2X SerDes1
SPI master SPI Flash
SYS DOR
CPRI CCM CLK
CLOCK Synth
25 M 122 MM
I2C_CH1
AMC
8X 4X
16x16 Switch VSC3316XJK for Each Direction
2X
SFP+ 2x4 1/2
Aurora
2X
eSPI
B4860 on Socket
IDC-10
100 M/125 M/156.25 M
MII Master
2X AMC
100 M/125 M/156.25 M USB 2.0
USB 2.0
ULPI
UlPI PHY USB2SER PHY I2C_CH0 I2C_CH0 I2C_CH0
VID
DDR-2
DDR3 x16
DDR3 x16
JTAG Matrix Event
COP
4X
I2C-1
DDR3 x16
DDR3 x16
FPGA Reset Logic I2C Master
8-ch. Boot Switch
DDR3 x16 SPD2
I2C_CH0
SFP+ 2x4 2/2
4X
1533 CLK-IN
GPIO2_3
I2C_CH7 I2C_CH0 I2C Boot EEPROM
I2C_CH0
VID
... GPIO Test Field
8x8 Switch VSC3308XJM for Each Direction I2C_CH5
1866M @2 GB @ 64 + ECC
eCWTAP RJ-45
SerDes2
JTAG
Kinetis MPC
USB 2.0
4X
USB ULPI
FPGA UART Switch
RJ-45
2X DUAL SGMII PHY VSC8662
EMI2 EMI1
UART1
RS232
SERDES2 FER CLK Jitt. Alt
I2C_CH1
PCN ON/OFF
RTC
System EEPROM
12 V AMC
AC/DC
AMC
Onboard resources and the associated tools enable developers to perform a variety of tasks, including: • Download and run code • Set breakpoints • Display memory and registers • Connect proprietary hardware via an expansion connector • B4860QDS supports two working modes: Stand-alone mode: The B4860QDS can run in a stand-alone mode like other application development systems, with direct connections to debuggers, power supply and other external connections such SFP+ optical transceivers and Ethernet transceivers. AdvancedMC™ mode: The B4860QDS is inserted into a standard MicroTCA® chassis that allows connecting to other B4860QDS or other AMC cards residing in the same chassis, enabling software developers to extend their system beyond a single device system via the high-speed Serial RapidIO® at 5G, CPRI at 9.8G, SGMII, 10 GB Ethernet or PCI Express® at 5G ports.The AMC edge connector on the B4860QDS carries these high-speed interface signals.
Features • Size: Dual-AMC form factor • Two DDR memory controllers supporting: 4 GB dual rank 72-bit memory, 1.866 GHz with ECC 2 GB single rank 72-bit memory, 1.866 GHz with ECC • Multiple configuration over 16 SerDes lanes, supporting:
Two 1x/2x/4x serial RapidIO I/F operate at 1.25, 2.5, 3.125 or 5 Gbaud comply with specification 2.1, exposed over AMC edge connector Eight lanes of CPRI with available data rates: 1.2288, 2.4576, 3.072, 4.9152, 6.144, 9.8304 Gbaud comply with CPRI specification v4.2, exposed over SFP transceivers or over AMC edge connector PCI Express port complies with the PCI Express base specification, revision 2.0 with x4, x2, and x1 link support running at 2.5 Gbaud or 5.0 Gbaud, exposed over AMC edge connector • Multiplexing Two SerDes instances, each with eight lanes: SerDes 1 multiplexing using two Vitesse cross-point 16 x 16 switch VSC3316 SerDes 2 multiplexing using two Vitesse cross-point 8 x 8 switch VSC3308 • SFP+ optical transceivers: Two optical transceivers, expandable to four transceivers • USB interface: USB specification rev. 2.0, up to 480 Mb/s with USB3315 ULPI PHY • External Ethernet interfaces: Dual SGMII PHY Vitesse VSC8662 to 2xRJ-45 copper connectors • IFC controller supporting: NAND flash: 512 MB, 8-bit Parallel NOR flash or PromJet: 128 MB, 16-bit • B4860 configuration may be loaded from nine-bit coded reset configuration, the RCW source is set by the appropriate DIP switches:
• UART: Available over USB-to-UART translator FTDI FT232R or over RS232 flat cable • GPIO, IRQ and timer signals are available on test point field • Available debug interfaces: Onboard eCWTAP controller with ETH and USB I/F (direct connection to host platform, no need for external TAP) JTAG/COP 16-pin header for external TAP controller Aurora debug connector External JTAG source over AMC
Development Tools Support Freescale supplies a complete set of CodeWarrior tools for the B4860. These tools provide easier and more robust ways for designers to develop optimized systems, giving them everything they need to exploit the advanced capabilities of the B4860 architecture. In addition to the B4860QDS board, the CodeWarrior Eclipse-based integrated development environment includes: • C and C++ compilers for Power Architecture and StarCore solutions • Librarian • Multicore debugger • Royalty-free DSP RTOS • Functional and performance-accurate software simulators • Advanced profiler • Linux SDK • Device drivers for embedded accelerators and peripherals
16-bit NOR flash/PROMJet
Six SGMII ports at 2.5G/1.0G
• High-speed run control
QIXIS 8-bit NOR flash emulator
Two XFI port 10.3125 Gb/s, exposed over SFP transceivers or over AMC edge connector
8-bit NAND flash
Orderable Part Numbers
Two 10 GB XAUI ports with four lanes at 3.125 Gbaud, exposed over SFP transceivers or over AMC edge connector
I2C EEPROM
24-bit SPI flash
• eSPI: Synchronous peripheral serial bus, running up to 80 Mb/s supported by SPI EEPROM
B4860QDS: with B4860 security accelerators B4860QDS-NE: without B4860 security accelerators
For more information, visit freescale.com/QorIQQonverge Freescale, the Freescale logo, CodeWarrior and StarCore are trademarks or registered trademarks of Freescale Semiconductor, Inc., Reg. U.S. Pat. & Tm. Off. QorIQ Qonverge is a trademark of Freescale Semiconductor, Inc. The Power Architecture and Power.org word marks and the Power and Power.org logos and related marks are trademarks and service marks licensed by Power.org. All other product or service names are the property of their respective owners. ©2012–2014 Freescale Semiconductor, Inc. Document Number: B4860QDSFS REV 2
