Transcript
Quantity Item No. Description MS1800-1 Main Support Frame MS1800-2 16.00 x 6.50 - 8 Wheel / Tire Assembly MS1800-3 1/4" x 1-3/4" Grade 5 Bolt / Nut MS1800-4 3/4" Flat Washer MS1800-5 3/4" I.D. Sleeve Bearing MS1800-6 Cam Shaft MS1800-7 1/8" Cotter Pin MS1800-8 Drive Sprocket MS1800-9 Drive Chain (#55 Link Chain) MS1800-10 3/4" Beater Drive Axle MS1800-11A Transmission Housing MS1800-12 5/8" x 3-1/2"Grade 5 Bolt MS1800-13 5/8" Nut MS1800-14A Combination Sprocket Assembly MS180016 5/16" x 1" Grade 5 Bolt/Nut/Washer Assembly MS180017 Drive Pulley (8 x 5/8" bore) MS1800-18 Belt Tightener Rod MS1800-19 1 x 6 Wolmanizcd Side Board MS1800-20 Side Board Support Stake MS1800-21 4L690 V-Belt (69") MS1800-22 Beater Shaft Pulley (8 x 3/4" bore) MS1800-23 Beater Stabilizer Bar MS1800-24 Left Beater Support MS1800-25 Right Beater Support MS1800 26 Beater Assembly MS1800-27 Drag Chain Assembly (#55 Link Chain) MS1800-28 Beater Support Bearing MS1800-30 3/32 Cotter Pin MS1800-31A Ratchet Flipper MS1800-32 Ratchet Spring MS1800-33A Connector Rod Boh/Nut Assembly MS1800-34A Connector Rod MS1800-35 1/4" Flat Washer MS1800-36 Beater Clutch Handle MS1800-37 Beater Clutch Spring MS1800-38 5/8" Flat Washer MS1800-39 Beater Clutch Hold Rod MS1800-40 1/4" Set Collar MS1800-41 Idler Sprocket Adjuster MS1800-42 Idler Sprocket MS1800-43 1/2" Hex Nut MS1800-44 1/4" 1-1/2" Carriage Bolt/Nut/Washer Assembly MS1800-45 Front Slant Panel Boards (1 x 6) MS1800-46 Left Slant Panel Support MS1800-47 Right Slant Panel Support MS1800-48 Idler Shaft MS1800-49 1 x 6 Wolmanized Floor Board MS1800-50 Floor Board Hold Bracket MS1800-51 Tongue Assembly MS1800-52 Wheel Hub Assembly (Includes Lug Bolts/Nuts) MS1800-53 3/16 x 5/8 Keyway Insert MS18M-53A 3/16 x 1/2 Keyway Insert MS1800-54 5/8 ID Bronze Bushing MS1800-55 Pulley Drive Shaft MS1800-56 3" Idler Pulley MS1800-57 12 Tooth Sprocket MS1800-58 3/8 x 1-1/2 Carriage Bolt & Nut MS1800-59 #35 Transmission Chain MS1800-60 Drag Chain Driv Shaft MS1800-61 Ratchet Sprocket
M u l t i - P u r p o s e S
p
M o d e l
r
e
#
O w n e r ' s
a
M
d
e
S
r
-
1
8
0
M a n u a l
0
OWNER MANUAL AND INSTRUCTIONS
Exploded View Model MS-1800
I Introduction: The model MS-1800 Mutti-Purpose Spreader is designed for the horseman, small farmer, or homesteader with a need for spreading manure with a small horsepower tractor. It can be pulled directly Into small spaces, yet has a capacity large enough to minimize the number of loads. Straw, hay or manure of most consistencies can be spread with ease. Strick adherence to maintenance is necessary to insure long life and continued operation. CAUTION: THE SPREADER SHOULD ONLY BE OPERATED WHEN ALL SURROUNDINGS ARE CLEAR OF PEOPLE AND BREAKABLE OBJECTS TO PREVENT POSSIBLE INJURY OR DAMAGE. II Assembly Instructions:
V-Belt (Step 7)
Stabilizer Bar (Step 5)
Angle Iron Stake (Step 6)
Side B o a r d (Step 6)
Rear
Tongue
Beater
(Step 3)
Assembly Drive W4) heel (Step (Step l ) Slant Panel (Step 2)
Tools Required: a. 1/2 inch wrench (opened or box end) b. 7/16 inch wrench (opened or box end) c. 3/4 inch opened end wrench d. hammer e. pliers f. 3/16 alien wrench g. 3/32 alien wrench h. grease gun i. wood block
Assembly Instructions (cont'd)
Warranty Policy Millside Industries Inc. will, at its option, replace or repair, without charge to the original purchaser, any part or parts manufactured by it and found, upon examination, to be DEFECTIVE IN MATERIAL AND/OR WORKMANSHIP If received for such examination within 90 days from date of original purchase. Damage resulting from accident, abuse, or neglect are conditions under which warranty cannot be claimed. Nor will warranty apply to damage resulting from failure to follow the Manufacturer's instruction for operation and maintenance nor from the improper selection of a particular application. All transportation charges on, and damages and loss incurred in connection with the transportation of, parts submitted for replacement or repair under this WARRANTY shall be borne by the purchaser. No other warranties, guarantees, or liabilities, either implied or expressed, will be the responsibility of Millside Industries Inc.
1. Install wheels by inserting four lag bolts into each hub so that threads protrude out. Install hub onto axle and Insert 1/4" x 1-3/4" bolt and lock nut through bob and axle hole provided. Slide the wheels onto the hub bolts with the valve stem facing outward. Install lag nuts and tighten securely. 2. Assemble the front slant panel by boning the three predrilled short boards to the left and right supports using the six 1/4" carriage bolts and nuts. (The short side of each slant panel support faces inward) Set the front slant panel onto the spreader such that the mounting holes align with the side rail mounting holes. Loosely install 5/16" x 1" bolts and nuts into front mounting holes to hold panel in place for step 3. 3. Install tongue over slant panel rear mounting holes and insert 5/16" x 1" bolts and nuts through rear mounting holes of tongue, slant panel, and aide rails. Remove slant panel front mounting bolts installed in step 2 above. Swing tongue upward until front mounting boles align and reinsert bolts and nuts. Tighten all four mounting bolts. 4. Slide beater ends into the two bearings located on the two support brackets and Install beater assembly at the rear of the spreader using four 3/8" x 1" bolts and nuts. Insure that the beater supports are firmly against the bottom of the side rail before tightening. The bolts should be inserted so that the bolt heads are on the outside to prevent interference with the other components. The mounting holes are slotted for beater V-belt adjustment and to insane clearance of approximately 1/4" between the beater and drag chain paddles during operation. 5., Install rear stabilizer bar into square tube on each beater support bracket Slight hammer tapping might be necessary using a wood block between hammer and bar. Insure that the bar is not cocked to preclude binding of beater during operation. NOTE: Make sure beater turns freely. If not, loosen beater bearing bolts and retighten 6. Install side boards into slots provided by front slant panel and rear beater supports, insert angle Iron side stakes to provide outward support of the side boards. 7. Install beater drive pulley onto beater shaft using the 3/8" long key way. Insert and tighten alien screw on pulley. Install beater drive V-belt with tightener arm positioned on the top side of the V-belt: The tightener arm is spring loaded from the opposite side of the spreader. When the clutch lever is pulled forward the tightener arm should dear the V-belt. At this point tighten the alien screw on the 1/4" shaft collar so that clutch lever is held forward via the set collar and keyhole located forward of the clutch lever. 8. Grease the two wheel bearings at the fittings located on the two axle supports. Grease the beater drive pulley bearing located behind the 8" pulley on the side rails of the chassis.
