Transcript
Quickguide
Software Version camin 3.9.13, hand unit 3.9.12 - March 2011
Basic Operation Button & LED Guide hand unit LEDs LED READY LED
LED Status Off Green Flashing Green Flashing Red
System Status System off System idle Scale initialization Motors move slowly to first position Battery low
Red
At startup: system not ready
Troubleshooting Turn on system
Change battery or use power supply
Battery low No connection to camin RUN LED
Off
No RUN signal received from camera
Check cable
Green Red
Camera in standby mode Camera running Camera error
Check if RUN SIMUL is ON OK
Camera running up/down Camera changing speed
SLIDER LED
Off Green
Camera running out of sync System idle Lens limits have been set
Red
Motor controlled by slider is missing
Remove lens limits by pressing „LENS“ button Connect motor to appropriate jack on camin
No motor connected slider axis not assigned Flashing Red/Green Flashing Green KNOB LEDs Off (advanced knob only) Available when used with cdisplay II and cfocas Center LED Green Red LED BAR
Calibrating Calibration armed
Change slider configuration to different motor Wait for calibration to finish Release „CAL“ button to calibrate
System idle
Knob focus position matches auto focus position Shows necessary focus correction in direction and distance
cmotion Mechatronikentwicklungs- und HandelsgmbH Schanzstrasse 41/1 | 1140 Vienna, AUSTRIA phone +43 1 789 10 96 | www.cmotion.eu |
[email protected]
Quickguide
Software Version camin 3.9.13, hand unit 3.9.12 - March 2011
Basic Operation Button & LED Guide hand unit Buttons Button
Action
ON
Turn cvolution hand unit on or off
CAL
Calibrate all motors when pressed for 3 seconds
LENS (KNOB)
Set lens limits When pressed while holding CAL only the motor associated with knob is calibrated. When menu is active LENS is context sensitive and serves several purposes, shown in the menu.
KNOB
Set knob limits
RUN (Green)
User configurable button: RUN (starts/stops the camera) MARK (for quick offset or in conjunction with CFINDER or CDISPLAY Autofocus ON/Off Quick sync User configurable button: RUN (starts/stops the camera) MARK (for quick offset or in conjunction with CFINDER or CDISPLAY Autofocus ON/Off Quick sync Enter menu by pressing menu wheel twice Scroll in menu In SYNC menu: move slave motor
RUN (Red)
MENU WHEEL
LENS (SLIDER)
Set lens limits When pressed while holding CAL only the motor associated with slider is calibrated
ZOOM MENU BUTTON (ZOOM UNIT)
Reserved for future use
ZOOM MENU BUTTON UP
Increases zoom speed
ZOOM MENU BUTTON DOWN
Decreases zoom speed
LENS (ZOOM)
Set lens limits When pressed while holding CAL only the motor associated with zoom controller is calibrated
ZAP
Zoom as fast As Possible
cmotion Mechatronikentwicklungs- und HandelsgmbH Schanzstrasse 41/1 | 1140 Vienna, AUSTRIA phone +43 1 789 10 96 | www.cmotion.eu |
[email protected]
Quickguide
Software Version camin 3.9.13, hand unit 3.9.12 - March 2011
Basic Operation Button & LED Guide camin LED Status RF-LED / ON-LED (Operation Status)
RF Off
ON Off
System status camin off
Troubleshooting Check camin power switch Check power supply (9 V minimum)
Off
Flashing Red/Green
Flashing Red
Flashing Red/Green
Off
Green
Green
Green
Red
Flashing Red/Green
camin ready, (cable mode – channel selector set at 0) no client logged on camin ready (wireless mode), no client logged on camin ready, client logged on in cable mode camin ready, client logged on in wireless mode Start-Up: camin is booting After Start-Up: Selected channel already in use by another camin
Check cable for cable damage Turn on clients
Turn on clients Set channels accordingly OK Ok Turn off camin and change radio channel If that does not work, please contact cmotion
Channel is currently being changed
Motor LEDs
Flashing Red Green
Hardware fault Software incompatible between camin and clients Low battery camin will not work Motor Error Focus motor ready
Green/Flashing Red
System is calibrating
Change battery or use power supply Check motor cable (incorrect, broken) If no reason can be found, please contact cmotion Check if lens is running roughly
Motor cannot reach its position
Check if lens has not been calibrated yet
No motor connected
Calbrate lens Check motor cable
Flashing Green
Flashing Red
Red
Flashing Red
Off
Update all components
Check if camin is turned on
cmotion Mechatronikentwicklungs- und HandelsgmbH Schanzstrasse 41/1 | 1140 Vienna, AUSTRIA phone +43 1 789 10 96 | www.cmotion.eu |
[email protected]
