Transcript
VEHICLE CCTV AND SAFETY SYSTEMS
VEHICLE JOURNEY RECORDER
Quick Guide www.smartwitness.com
STEP 1: WHAT’S IN THE BOX? SVC100GPS
SVC100GPS-LCA/-LCA2
SVC100GPS Camera /Recording Unit including bracket
Item contains all accessories on the left, plus the following; Transparent Locking Case
Wire Splice Clips Set of stickers for Windscreen Mounting (Double-sided Tape x 2) Power Cable (Cigarette Jack)
Keys for Locking Case Telematics Cable Please note: The SVC100GPS-LCA2 will have an extra alarm output wire
USB 2.0 SD Card Reader Spare Mounting Bracket SD Memory Card*
* SD Card size will depend on the model and may not be included.
STEP 2: INSERT SD CARD Please Note
If you have been supplied with an SD card, then this will need to be set-up using the latest Smart Witness software.
1. This software can be downloaded from www.smartwitness.co.uk/article/76/support
Once on the page, select the correct software by using the Drop Down Menu
2. When downladed, go to the ‘Downloads’ folder and double click the ‘setup’ file. 3. Follow the set-up instructions, then the software icon will appear on your desktop.
2
www.smartwitness.com
4. Double click the software icon to load the software. (Below)
5. Click the ‘Tool’ button 6. Select the “SD Card Initilise” button from the drop down menu
7. You will presented with another drop down list to select the Card to format. 8. Select the “DRIVERREC” from the drop down and tick the “Quick Format” box when prompted. 9. Click “Start” to begin formatting. 10. Once the card has been formatted, you will see the screen on the right. Then, remove the SD Card from the computer.
11. Make sure the unit is turned off before inserting the SD Card. 12. Insert the SD memory card into the SD card slot.
Please Note
The very first time you power up your unit with the SD Card inserted, it is important not to disconnect the power before the 2 minutes are up, as this may damage the unit.
www.smartwitness.com
3
STEP 3: INSTALLATION SVC100GPS
- Designed for DIY Fitting
1. Attach the double-sided adhesive tape to the unit.
2. Secure the SVC100GPS to the windscreen behind the rear view mirror. Please make sure that the surface is clean and dry before attaching. Tip: Hold in position with firm pressure for 30 Seconds
3. Adjust camera view and make sure the lens has an unobstructed view.
4. Arrange the power cord neatly alongside the windshield and door pillar trim. Use the provided wire splice clip.
5. Connect the SVC100GPS to the cigarette lighter socket.
SVC100GPS-LCA/-LCA2
- Professional Installation Recommended
Please don’t attempt to permanently wire this unit unless you are familiar with auto wiring. Any incorrect installations will not be covered by the warranty.
4
www.smartwitness.com
For a full wiring description, please see the manual.
STEP 4: LED Guide
Blue LED
Red LED
See the table below for an explanation of the LED status changes on the back of the recorder. No.
BLUE LED
RED LED
1
Blink every half second
OFF
2
Blink every 4 Seconds
OFF
Continuous Recording
3
SOLID
OFF
Pre-Recording (Awaiting Triggers)
4
OFF
Blink every half second
Card Fault
5
SOLID
SOLID
6
Blink every half second Blink every half second
Meaning Event Recording
System Booting Up Unit Fault
7
SOLID
OFF
SD Card Removal in Safe Mode
8
OFF
OFF
No Power
SAFE SD CARD REMOVAL To remove the SD card either: Disconnect the power to the unit, wait until all LEDs are off and then remove the card. Use SAFE MODE. To enter safe mode whilst the unit is powered and in recording mode, press the “SD Card Format” (Blue) button for 3 seconds until the unit beeps to acknowledge it is in safe mode, then remove the SD card.
www.smartwitness.com
5
