Transcript
SL-DKX-050 ServerLink DVI KVM Extender over Cat 5 - DVI, USB KB & Mouse, Audio & 1 x USB 2.0 Device up to 50mtr
Quick Installation Guide
Package Contents Transmitter (TX) Unit x 1 Receiver (RX) Unit x 1 DVI-D Male to Male cable x 1 USB cable (Type A to Type B) x 1 USB to DC Jack Cable x 1 Power Adapter (DC5V 2A) x 1 This Quick Installation Guide x 1
SL-DKX-050 ServerLink DVI KVM Extender over Cat 5, DVI, USB KB & Mouse, Audio & 1 x USB 2.0 Device up to 50mtr
c. d. e. f. g.
DVI input - connect to computer’s DVI output port USB Port (USB Type B) - connect to PC USB port RJ45 CAT5 Extension Port (A) RJ45 CAT5 Extension Port (B) Power Receptacle (DC5V 500mA, centre-positive)
Receiver Unit (RX) - Remote [RX - Front Panel]
Front & Rear Panel Connectors The front and back panels are where the various connectors are located on the CAT5 DVI KVM Extender. Before you connect these two units to any cabling or devices, you should familiarise yourself with these connectors to simplify installation. Receiver (RX) Unit – Front Panel Transmitter Unit (TX) - Local [TX - Front Panel]
1. 2. 3. 4. 5. 6. 7. 8.
Transmitter Unit (TX)
Power LED (Red) (Lit when the power is on) Link LED (Green) (Lit when the link is on) Microphone Jack Line-in Jack 3.5mm Stereo Audio Speaker Jack USB Keyboard Port USB Mouse Port USB 2.0 Device Port
Transmitter (TX) Unit – Front Panel
Receiver Unit (RX) INTRODUCTION The SL-DKX-050 DVI Extender over Cat 5 can extend your DVI monitor, keyboard, mouse, audio and a USB 2.0 device up to 50mtr away from your computer over a two (2) CAT 5 or CAT 6 UTP cables.
[RX – Back Panel] a. b.
Power LED (Red) (Lit when the power is on) Link LED (Green) (Lit when the link is on)
[TX - Back Panel]
Receiver (RX) Unit – Back Panel The CAT5 DVI Extender comprises two separate units - the Receiver (RX) Unit and the Transmitter (TX) Unit. With automatic EDID configuration, stereo audio support and crystal clear video reproduction, the SL-DKX-050 is simple to install, configure and operate.
Transmitter (TX) Unit – Back Panel
1
9. 10. 11. 12. 13.
DVI output - connect to DVI monitor EQ (Equalizer) Port RJ45 CAT5 Extension Port (A) RJ45 CAT5 Extension Port (B) Power Receptacle (DC5V 2A, centre-positive)
Rev. 1.2
Copyright© All rights reserved.
SL-DKX-050 ServerLink DVI KVM Extender over Cat 5 - DVI, USB KB & Mouse, Audio & 1 x USB 2.0 Device up to 50mtr INSTALLATION
FCC This equipment has been tested and found to comply with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference (2) This device must accept any interference received. Including interference that may cause undesired operation.
Configure the Transmitter Unit (TX) - Local Front Panel (TX) No cable connections required.
CE This equipment is in compliance with the requirements of the following regulations: EN 55 022: CLASS B.
Back Panel (TX) 1.
2. 3. 4.
Connect one CAT 5 or CAT 6 cable to the Transmitter RJ45 port A (e) and a 2nd Cat 5 or Cat 6 cable to the Transmitter RJ45 port B (f) Connect the Transmitter’s DVI port (c) to the computer’s DVI output port using the included DVI cable Connect the Transmitter’s USB port (d) to the computer’s USB port using the included USB cable Connect the USB to DC Jack cable to the Transmitter to power it up (g)
C-Tick This equipment is in compliance with ACMA’s Electromagnetic Compatibility (EMC) regulatory arrangements under the Radiocommunications Act 1992. RoHS All contents of this package, including products, packing materials and documentation comply with RoHS.
Configure the Receiver Unit (RX) - Remote Front Panel (RX) 1. 2. 3. 4. 5.
Connect the Microphone to the microphone jack (3) (Optional) Connect the Line-in cable to the Line-in jack (4) (Only when recording required.(Optional) Connect the speaker to the stereo audio jack (5) (Optional) Connect a USB keyboard (6) and a USB mouse (7) to the USB ports Connect a USB 2.0 Device (8) (Optional)
Back Panel (RX) 1. 2. 3. 4. 5.
Connect the DVI monitor to the DVI output port (9) Connect one CAT 5 or CAT 6 cable to the Receiver RJ45 port A (11) corresponding to the Transmitter A Connect a 2nd Cat 5 or Cat 6 cable to the Receiver RJ45 port B (12) corresponding to the Transmitter B Connect the AC power adapter to the Receiver to power it up (13) If the remote monitor is blank or intermittently blank, adjust the EQ (Equalizer) rotating switch (10) as needed until a stable display is achieved
TROUBLESHOOTING Q: I have connected all the cables correctly and powered on the extender, however the monitor doesn’t display any video image. How can I solve this problem? A: If you encounter no video display, please adjust the Receiver Unit’s EQ (Equalizer) rotating switch until a video image is displayed. Notes: 1.
Use good quality CATx UTP cable (max. 50mtr). Note that good quality cable will give better video outcome over a longer distance.
2.
The choice of path of the CATx UTP cable should not only take into account the shortest possible path, but also one that is relatively far away from any significant electromagnetic interference source.
2
Rev. 1.2
Copyright© All rights reserved.
